| Age | Commit message (Collapse) | Author |
|---|
|
commit 25a097f5204675550afb879ee18238ca917cba7a upstream.
`uref->usage_index` is not always being properly checked, causing
hiddev_ioctl_usage() to go out of bounds under some cases. Fix it.
Reported-by: syzbot+34ee1b45d88571c2fa8b@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=f2aebe90b8c56806b050a20b36f51ed6acabe802
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 20934c0de13b49a072fb1e0ca79fe0fe0e40eae5 upstream.
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d4169834628d18b2392a2da92b7fbf5e8e2ce89 upstream.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf87 ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9aa37788e7ebb3f489fb4b71ce07adadd444264a upstream.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5967116e8358899ebaa22702d09b0af57fef23e1 upstream.
There's another Raydium touchscreen needs the no-lpm quirk:
[ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.339151] usb 1-9: Product: Raydium Touch System
[ 1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[ 6.450497] usb 1-9: can't set config #1, error -110
BugLink: https://bugs.launchpad.net/bugs/1889446
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200731051622.28643-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a469bc9f32dd33c7aac5744669d21a023a719cd upstream.
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f176ede3a3bde5b398a6777a7f9ff091baa2d3ff upstream.
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:
do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000370c7c68>] prepare_to_wait+0xb1/0x2a0 kernel/sched/wait.c:247
WARNING: CPU: 1 PID: 340 at kernel/sched/core.c:7253 __might_sleep+0x135/0x190
kernel/sched/core.c:7253
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 340 Comm: syz-executor677 Not tainted 5.8.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
panic+0x2aa/0x6e1 kernel/panic.c:231
__warn.cold+0x20/0x50 kernel/panic.c:600
report_bug+0x1bd/0x210 lib/bug.c:198
handle_bug+0x41/0x80 arch/x86/kernel/traps.c:234
exc_invalid_op+0x14/0x40 arch/x86/kernel/traps.c:254
asm_exc_invalid_op+0x12/0x20 arch/x86/include/asm/idtentry.h:536
RIP: 0010:__might_sleep+0x135/0x190 kernel/sched/core.c:7253
Code: 65 48 8b 1c 25 40 ef 01 00 48 8d 7b 10 48 89 fe 48 c1 ee 03 80 3c 06 00 75
2b 48 8b 73 10 48 c7 c7 e0 9e 06 86 e8 ed 12 f6 ff <0f> 0b e9 46 ff ff ff e8 1f
b2 4b 00 e9 29 ff ff ff e8 15 b2 4b 00
RSP: 0018:ffff8881cdb77a28 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8881c6458000 RCX: 0000000000000000
RDX: ffff8881c6458000 RSI: ffffffff8129ec93 RDI: ffffed1039b6ef37
RBP: ffffffff86fdade2 R08: 0000000000000001 R09: ffff8881db32f54f
R10: 0000000000000000 R11: 0000000030343354 R12: 00000000000001f2
R13: 0000000000000000 R14: 0000000000000068 R15: ffffffff83c1b1aa
slab_pre_alloc_hook.constprop.0+0xea/0x200 mm/slab.h:498
slab_alloc_node mm/slub.c:2816 [inline]
slab_alloc mm/slub.c:2900 [inline]
kmem_cache_alloc_trace+0x46/0x220 mm/slub.c:2917
kmalloc include/linux/slab.h:554 [inline]
dummy_urb_enqueue+0x7a/0x880 drivers/usb/gadget/udc/dummy_hcd.c:1251
usb_hcd_submit_urb+0x2b2/0x22d0 drivers/usb/core/hcd.c:1547
usb_submit_urb+0xb4e/0x13e0 drivers/usb/core/urb.c:570
yurex_write+0x3ea/0x820 drivers/usb/misc/yurex.c:495
This patch changes the call to use GFP_ATOMIC instead of GFP_KERNEL.
Reported-and-tested-by: syzbot+c2c3302f9c601a4b1be2@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810182954.GB307778@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
set_primary_fwnode()
commit c15e1bdda4365a5f17cdadf22bf1c1df13884a9e upstream.
When the primary firmware node pointer is removed from a
device (set to NULL) the secondary firmware node pointer,
when it exists, is made the primary node for the device.
However, the secondary firmware node pointer of the original
primary firmware node is never cleared (set to NULL).
To avoid situation where the secondary firmware node pointer
is pointing to a non-existing object, clearing it properly
when the primary node is removed from a device in
set_primary_fwnode().
Fixes: 97badf873ab6 ("device property: Make it possible to use secondary firmware nodes")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3eb6e8fba65094328b8dca635d00de74ba75b45 upstream.
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
Fixes: 1e2ef05bb8cf8 ("PM: Limit race conditions between runtime PM and system sleep (v2)")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 904df64a5f4d5ebd670801d869ca0a6d6a6e8df6 upstream.
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
data pointer which contains XEN specific information.
commit c330fb1ddc0a922f044989492b7fcca77ee1db46 upstream.
handler data is meant for interrupt handlers and not for storing irq chip
specific information as some devices require handler data to store internal
per interrupt information, e.g. pinctrl/GPIO chained interrupt handlers.
This obviously creates a conflict of interests and crashes the machine
because the XEN pointer is overwritten by the driver pointer.
As the XEN data is not handler specific it should be stored in
irqdesc::irq_data::chip_data instead.
A simple sed s/irq_[sg]et_handler_data/irq_[sg]et_chip_data/ cures that.
Cc: stable@vger.kernel.org
Reported-by: Roman Shaposhnik <roman@zededa.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Roman Shaposhnik <roman@zededa.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/87lfi2yckt.fsf@nanos.tec.linutronix.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream.
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
chain #1:
serial8250_do_startup()
spin_lock_irqsave(&port->lock);
disable_irq_nosync(port->irq);
raw_spin_lock_irqsave(&desc->lock)
chain #2:
__report_bad_irq()
raw_spin_lock_irqsave(&desc->lock)
for_each_action_of_desc()
printk()
spin_lock_irqsave(&port->lock);
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock:
ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock:
ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&irq_desc_lock_class){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
__irq_get_desc_lock+0x65/0x89
__disable_irq_nosync+0x3b/0x93
serial8250_do_startup+0x451/0x75c
uart_startup+0x1b4/0x2ff
uart_port_activate+0x73/0xa0
tty_port_open+0xae/0x10a
uart_open+0x1b/0x26
tty_open+0x24d/0x3a0
chrdev_open+0xd5/0x1cc
do_dentry_open+0x299/0x3c8
path_openat+0x434/0x1100
do_filp_open+0x9b/0x10a
do_sys_open+0x15f/0x3d7
kernel_init_freeable+0x157/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #1 (&port_lock_key){-.-.}:
_raw_spin_lock_irqsave+0x61/0x8d
serial8250_console_write+0xa7/0x2a0
console_unlock+0x3b7/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
register_console+0x336/0x3a4
uart_add_one_port+0x51b/0x5be
serial8250_register_8250_port+0x454/0x55e
dw8250_probe+0x4dc/0x5b9
platform_drv_probe+0x67/0x8b
really_probe+0x14a/0x422
driver_probe_device+0x66/0x130
device_driver_attach+0x42/0x5b
__driver_attach+0xca/0x139
bus_for_each_dev+0x97/0xc9
bus_add_driver+0x12b/0x228
driver_register+0x64/0xed
do_one_initcall+0x20c/0x4a6
do_initcall_level+0xb5/0xc5
do_basic_setup+0x4c/0x58
kernel_init_freeable+0x13f/0x1dd
kernel_init+0xe/0x105
ret_from_fork+0x27/0x50
-> #0 (console_owner){-...}:
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
console_lock_spinning_enable+0x51/0x57
console_unlock+0x25d/0x528
vprintk_emit+0x111/0x17f
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
ret_from_intr+0x0/0x1d
cpuidle_enter_state+0x12f/0x1fd
cpuidle_enter+0x2e/0x3d
do_idle+0x1ce/0x2ce
cpu_startup_entry+0x1d/0x1f
start_kernel+0x406/0x46a
secondary_startup_64+0xa4/0xb0
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &irq_desc_lock_class
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&irq_desc_lock_class);
lock(&port_lock_key);
lock(&irq_desc_lock_class);
lock(console_owner);
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
#1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55
Hardware name: XXXXXX
Call Trace:
<IRQ>
dump_stack+0xbf/0x133
? print_circular_bug+0xd6/0xe9
check_noncircular+0x1b9/0x1c3
__lock_acquire+0x118d/0x2714
lock_acquire+0x203/0x258
? console_lock_spinning_enable+0x31/0x57
console_lock_spinning_enable+0x51/0x57
? console_lock_spinning_enable+0x31/0x57
console_unlock+0x25d/0x528
? console_trylock+0x18/0x4e
vprintk_emit+0x111/0x17f
? lock_acquire+0x203/0x258
printk+0x59/0x73
__report_bad_irq+0xa3/0xba
note_interrupt+0x19a/0x1d6
handle_irq_event_percpu+0x57/0x79
handle_irq_event+0x36/0x55
handle_fasteoi_irq+0xc2/0x18a
do_IRQ+0xb3/0x157
common_interrupt+0xf/0xf
</IRQ>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Raul Rangel <rrangel@google.com>
BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800
Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream.
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream.
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc5269ca765057a1b762e79a1cfd267cd7bf1c46 upstream.
vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl
to save struct vc_data values that are modified and restore the original
values in case of error.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/1596213192-6635-2-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8d1653daec02315e06d30246cff4af72e76e54e upstream.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 531412492ce93ea29b9ca3b4eb5e3ed771f851dd upstream.
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
out-of-bounds access
commit 39b3cffb8cf3111738ea993e2757ab382253d86a upstream.
Add a check to fbcon_resize() to ensure that a possible change to user font
height or user font width will not allow a font data out-of-bounds access.
NOTE: must use original charcount in calculation as font charcount can
change and cannot be used to determine the font data allocated size.
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/1596213192-6635-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 989e4da042ca4a56bbaca9223d1a93639ad11e17 ]
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 93b6c5db06028a3b55122bbb74d0715dd8ca4ae0 ]
In ufshcd_suspend(), after clk-gating is suspended and link is set
as Hibern8 state, ufshcd_hold() is still possibly invoked before
ufshcd_suspend() returns. For example, MediaTek's suspend vops may
issue UIC commands which would call ufshcd_hold() during the command
issuing flow.
Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled,
then ufshcd_hold() may enter infinite loops because there is no
clk-ungating work scheduled or pending. In this case, ufshcd_hold()
shall just bypass, and keep the link as Hibern8 state.
Link: https://lore.kernel.org/r/20200809050734.18740-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Co-developed-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b8eb2ee9da1e8c9b8082f404f3948aa82a057b2 ]
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 914a7b3563b8fb92f976619bbd0fa3a4a708baae ]
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1769bb68a850508a492e3674ab1e5e479b11254 ]
This reverts commit 76d164f582150fd0259ec0fcbc485470bcd8033e.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b53a19284f537168fb506f2f40d7fda40a01162 ]
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Link: https://lore.kernel.org/r/20200711043018.928-1-charley.ashbringer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 602649eadaa0c977e362e641f51ec306bc1d365d ]
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 709ed1bcef12398ac1a35c149f3e582db04456c2 ]
The Intel uncore driver may claim some of the pci ids from ie31200 which
means that the ie31200 edac driver will not initialize them as part of
pci_register_driver().
Let's add a fallback for this case to 'pci_get_device()' to get a
reference on the device such that it can still be configured. This is
similar in approach to other edac drivers.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/1594923911-10885-1-git-send-email-jbaron@akamai.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e95b4789ff4380733006836d28e554dc296b2298 ]
In fcoe_sysfs_fcf_del(), we first deleted the fcf from the list and then
freed it if ctlr_dev was not NULL. This was causing a memory leak.
Free the fcf even if ctlr_dev is NULL.
Link: https://lore.kernel.org/r/20200729081824.30996-3-jhasan@marvell.com
Reviewed-by: Girish Basrur <gbasrur@marvell.com>
Reviewed-by: Santosh Vernekar <svernekar@marvell.com>
Reviewed-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68e12e5f61354eb42cfffbc20a693153fc39738e ]
If scsi_host_lookup() fails we will jump to put_host which may cause a
panic. Jump to exit_set_fnode instead.
Link: https://lore.kernel.org/r/20200615081226.183068-1-jingxiangfeng@huawei.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 990a1162986e8eff7ca18cc5a0e03b4304392ae2 ]
nouveau_connector_detect() calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bfad51c7633325b5d4b32444efe04329d53297b2 ]
nouveau_fbcon_open() calls calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03128643eb5453a798db5770952c73dc64fcaf00 ]
If usb_submit_urb fails the allocated urb should be unanchored and
released.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-3-code@reto-schneider.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a94644b440eef5a7b9c104ac8aa7a7f413e35e5 ]
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348b8 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
Link: https://lore.kernel.org/r/20200528021322.1984-1-wu000273@umn.edu
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03dbfe0668e6692917ac278883e0586cd7f7d753 ]
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f79f94765f8c39db0b7dec1d335ab046aac03f20 ]
The call to pm_runtime_get_sync increments the counter even in case of
failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e008fa6fb41544b63973a529b704ef342f47cc65 ]
in amdgpu_display_crtc_set_config, the call to pm_runtime_get_sync
increments the counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5509ac65f2fe5aa3c0003237ec629ca55024307c ]
in amdgpu_drm_ioctl the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9ba8923cbbe11564dd1bf9f3602add9a9cfbb5c6 ]
in amdgpu_driver_open_kms the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect
ref count. In case of failure, decrement the ref count before returning.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f2e8acdb48ed166b65d47837c31b177460491ec ]
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 20eca0123a35305e38b344d571cf32768854168c ]
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5a0c256d96f020e4771f6fd5524b80f89a2d3132 ]
If tcmu_handle_completions() has to process a padding shorter than
sizeof(struct tcmu_cmd_entry), the current call to
tcmu_flush_dcache_range() with sizeof(struct tcmu_cmd_entry) as length
param is wrong and causes crashes on e.g. ARM, because
tcmu_flush_dcache_range() in this case calls
flush_dcache_page(vmalloc_to_page(start)); with start being an invalid
address above the end of the vmalloc'ed area.
The fix is to use the minimum of remaining ring space and sizeof(struct
tcmu_cmd_entry) as the length param.
The patch was tested on kernel 4.19.118.
See https://bugzilla.kernel.org/show_bug.cgi?id=208045#c10
Link: https://lore.kernel.org/r/20200629093756.8947-1-bstroesser@ts.fujitsu.com
Tested-by: JiangYu <lnsyyj@hotmail.com>
Acked-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
value in debiirq()
[ Upstream commit 6499a0db9b0f1e903d52f8244eacc1d4be00eea2 ]
The value av7110->debi_virt is stored in DMA memory, and it is assigned
to data, and thus data[0] can be modified at any time by malicious
hardware. In this case, "if (data[0] < 2)" can be passed, but then
data[0] can be changed into a large number, which may cause buffer
overflow when the code "av7110->ci_slot[data[0]]" is used.
To fix this possible bug, data[0] is assigned to a local variable, which
replaces the use of data[0].
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 832707021666411d04795c564a4adea5d6b94f17 ]
When we tear down a network namespace, we unregister all
the netdevices within it. So we may queue a slave device
and a bonding device together in the same unregister queue.
If the only slave device is non-ethernet, it would
automatically unregister the bonding device as well. Thus,
we may end up unregistering the bonding device twice.
Workaround this special case by checking reg_state.
Fixes: 9b5e383c11b0 ("net: Introduce unregister_netdevice_many()")
Reported-by: syzbot+af23e7f3e0a7e10c8b67@syzkaller.appspotmail.com
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4ca0d9ac3fd8f9f90b72a15d8da2aca3ffb58418 ]
Broadcast mode bonds transmit a copy of all traffic simultaneously out of
all interfaces, so the "speed" of the bond isn't really the aggregate of
all interfaces, but rather, the speed of the slowest active interface.
Also, the type of the speed field is u32, not unsigned long, so adjust
that accordingly, as required to make min() function here without
complaining about mismatching types.
Fixes: bb5b052f751b ("bond: add support to read speed and duplex via ethtool")
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d0f5c7076e01fef6fcb86988d9508bf3ce258bd4 ]
Processing NETDEV_FEAT_CHANGE causes IPvlan links to lose
NETIF_F_LLTX feature because of the incorrect handling of
features in ipvlan_fix_features().
--before--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Actual changes:
vlan-challenged: off [fixed]
tx-lockless: off [fixed]
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: off [fixed]
lpaa10:~#
--after--
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~# ethtool -K ipvl0 tso off
Cannot change tcp-segmentation-offload
Could not change any device features
lpaa10:~# ethtool -k ipvl0 | grep tx-lockless
tx-lockless: on [fixed]
lpaa10:~#
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There appears to be a timing issue where using a divider of 32 breaks
the DSS for OMAP36xx despite the TRM stating 32 is a valid
number. Through experimentation, it appears that 31 works.
This same fix was issued for kernels 4.5+. However, between
kernels 4.4 and 4.5, the directory structure was changed when the
dss directory was moved inside the omapfb directory. That broke the
patch on kernels older than 4.5, because it didn't permit the patch
to apply cleanly for 4.4 and older.
A similar patch was applied to the 3.16 kernel already, but not to 4.4.
Commit 4b911101a5cd ("drm/omap: fix max fclk divider for omap36xx") is
on the 3.16 stable branch with notes from Ben about the path change.
Since this was applied for 3.16 already, this patch is for kernels
3.17 through 4.4 only.
Fixes: f7018c213502 ("video: move fbdev to drivers/video/fbdev")
Cc: <stable@vger.kernel.org> #3.17 - 4.4
CC: <tomi.valkeinen@ti.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For support of long running hypercalls xen_maybe_preempt_hcall() is
calling cond_resched() in case a hypercall marked as preemptible has
been interrupted.
Normally this is no problem, as only hypercalls done via some ioctl()s
are marked to be preemptible. In rare cases when during such a
preemptible hypercall an interrupt occurs and any softirq action is
started from irq_exit(), a further hypercall issued by the softirq
handler will be regarded to be preemptible, too. This might lead to
rescheduling in spite of the softirq handler potentially having set
preempt_disable(), leading to splats like:
BUG: sleeping function called from invalid context at drivers/xen/preempt.c:37
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 20775, name: xl
INFO: lockdep is turned off.
CPU: 1 PID: 20775 Comm: xl Tainted: G D W 5.4.46-1_prgmr_debug.el7.x86_64 #1
Call Trace:
<IRQ>
dump_stack+0x8f/0xd0
___might_sleep.cold.76+0xb2/0x103
xen_maybe_preempt_hcall+0x48/0x70
xen_do_hypervisor_callback+0x37/0x40
RIP: e030:xen_hypercall_xen_version+0xa/0x20
Code: ...
RSP: e02b:ffffc900400dcc30 EFLAGS: 00000246
RAX: 000000000004000d RBX: 0000000000000200 RCX: ffffffff8100122a
RDX: ffff88812e788000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffffff83ee3ad0 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000246 R12: ffff8881824aa0b0
R13: 0000000865496000 R14: 0000000865496000 R15: ffff88815d040000
? xen_hypercall_xen_version+0xa/0x20
? xen_force_evtchn_callback+0x9/0x10
? check_events+0x12/0x20
? xen_restore_fl_direct+0x1f/0x20
? _raw_spin_unlock_irqrestore+0x53/0x60
? debug_dma_sync_single_for_cpu+0x91/0xc0
? _raw_spin_unlock_irqrestore+0x53/0x60
? xen_swiotlb_sync_single_for_cpu+0x3d/0x140
? mlx4_en_process_rx_cq+0x6b6/0x1110 [mlx4_en]
? mlx4_en_poll_rx_cq+0x64/0x100 [mlx4_en]
? net_rx_action+0x151/0x4a0
? __do_softirq+0xed/0x55b
? irq_exit+0xea/0x100
? xen_evtchn_do_upcall+0x2c/0x40
? xen_do_hypervisor_callback+0x29/0x40
</IRQ>
? xen_hypercall_domctl+0xa/0x20
? xen_hypercall_domctl+0x8/0x20
? privcmd_ioctl+0x221/0x990 [xen_privcmd]
? do_vfs_ioctl+0xa5/0x6f0
? ksys_ioctl+0x60/0x90
? trace_hardirqs_off_thunk+0x1a/0x20
? __x64_sys_ioctl+0x16/0x20
? do_syscall_64+0x62/0x250
? entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix that by testing preempt_count() before calling cond_resched().
In kernel 5.8 this can't happen any more due to the entry code rework
(more than 100 patches, so not a candidate for backporting).
The issue was introduced in kernel 4.3, so this patch should go into
all stable kernels in [4.3 ... 5.7].
Reported-by: Sarah Newman <srn@prgmr.com>
Fixes: 0fa2f5cb2b0ecd8 ("sched/preempt, xen: Use need_resched() instead of should_resched()")
Cc: Sarah Newman <srn@prgmr.com>
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Chris Brannon <cmb@prgmr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 481a0d7422db26fb63e2d64f0652667a5c6d0f3e ]
The loop may exist if vq->broken is true,
virtqueue_get_buf_ctx_packed or virtqueue_get_buf_ctx_split
will return NULL, so virtnet_poll will reschedule napi to
receive packet, it will lead cpu usage(si) to 100%.
call trace as below:
virtnet_poll
virtnet_receive
virtqueue_get_buf_ctx
virtqueue_get_buf_ctx_packed
virtqueue_get_buf_ctx_split
virtqueue_napi_complete
virtqueue_poll //return true
virtqueue_napi_schedule //it will reschedule napi
to fix this, return false if vq is broken in virtqueue_poll.
Signed-off-by: Mao Wenan <wenan.mao@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1596354249-96204-1-git-send-email-wenan.mao@linux.alibaba.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec007ef40abb6a164d148b0dc19789a7a2de2cc8 ]
In fc_disc_gpn_id_resp(), skb is supposed to get freed in all cases except
for PTR_ERR. However, in some cases it didn't.
This fix is to call fc_frame_free(fp) before function returns.
Link: https://lore.kernel.org/r/20200729081824.30996-2-jhasan@marvell.com
Reviewed-by: Girish Basrur <gbasrur@marvell.com>
Reviewed-by: Santosh Vernekar <svernekar@marvell.com>
Reviewed-by: Saurav Kashyap <skashyap@marvell.com>
Reviewed-by: Shyam Sundar <ssundar@marvell.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4aec14de3a15cf9789a0e19c847f164776f49473 ]
When I cat parameter 'proto' by sysfs, it displays as follows. It's
better to add a newline for easy reading.
root@syzkaller:~# cat /sys/module/psmouse/parameters/proto
autoroot@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20200720073846.120724-1-wangxiongfeng2@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c487b0b0ea7ff22127fe99a7f67657d8730ff94 ]
If platform_driver_register() fails within vpss_init() resources are not
cleaned up. The patch fixes this issue by introducing the corresponding
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
