| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixes for interrupt controller drivers:
- Skip IRQ_M_EXT entries in the device tree when initializing the
RISCV PLIC controller to avoid a double init attempt.
- Use the correct ITS list when issuing the VMOVP synchronization
command so the operation works only on the ITS instances which are
associated to a VM"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Skip contexts except supervisor in plic_init()
irqchip/gic-v3-its: Use the exact ITSList for VMOVP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fix from Greg KH:
"Here is a single tty/serial driver fix for 5.4-rc5 that resolves a
reported issue.
It has been in linux-next for a while with no problems"
* tag 'tty-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
8250-men-mcb: fix error checking when get_num_ports returns -ENODEV
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix, for the wlan-ng driver, that
resolves a reported issue.
It is been in linux-next for a while with no reported issues"
* tag 'staging-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wlan-ng: fix exit return when sme->key_idx >= NUM_WEPKEYS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull binder fix from Greg KH:
"This is a single binder fix to resolve a reported issue by Jann. It's
been in linux-next for a while with no reported issues"
* tag 'char-misc-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: Don't modify VMA bounds in ->mmap handler
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.4-rc5.
More "fun" with some of the misc USB drivers as found by syzbot, and
there are a number of other small bugfixes in here for reported
issues.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdns3: Error out if USB_DR_MODE_UNKNOWN in cdns3_core_init_role()
USB: ldusb: fix read info leaks
USB: serial: ti_usb_3410_5052: clean up serial data access
USB: serial: ti_usb_3410_5052: fix port-close races
USB: usblp: fix use-after-free on disconnect
usb: udc: lpc32xx: fix bad bit shift operation
usb: cdns3: Fix dequeue implementation.
USB: legousbtower: fix a signedness bug in tower_probe()
USB: legousbtower: fix memleak on disconnect
USB: ldusb: fix memleak on disconnect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A few driver fixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: stm32f7: remove warning when compiling with W=1
i2c: stm32f7: fix a race in slave mode with arbitration loss irq
i2c: stm32f7: fix first byte to send in slave mode
i2c: mt65xx: fix NULL ptr dereference
i2c: aspeed: fix master pending state handling
|
|
Pull block and io_uring fixes from Jens Axboe:
"A bit bigger than usual at this point in time, mostly due to some good
bug hunting work by Pavel that resulted in three io_uring fixes from
him and two from me. Anyway, this pull request contains:
- Revert of the submit-and-wait optimization for io_uring, it can't
always be done safely. It depends on commands always making
progress on their own, which isn't necessarily the case outside of
strict file IO. (me)
- Series of two patches from me and three from Pavel, fixing issues
with shared data and sequencing for io_uring.
- Lastly, two timeout sequence fixes for io_uring (zhangyi)
- Two nbd patches fixing races (Josef)
- libahci regulator_get_optional() fix (Mark)"
* tag 'for-linus-2019-10-26' of git://git.kernel.dk/linux-block:
nbd: verify socket is supported during setup
ata: libahci_platform: Fix regulator_get_optional() misuse
nbd: handle racing with error'ed out commands
nbd: protect cmd->status with cmd->lock
io_uring: fix bad inflight accounting for SETUP_IOPOLL|SETUP_SQTHREAD
io_uring: used cached copies of sq->dropped and cq->overflow
io_uring: Fix race for sqes with userspace
io_uring: Fix broken links with offloading
io_uring: Fix corrupted user_data
io_uring: correct timeout req sequence when inserting a new entry
io_uring : correct timeout req sequence when waiting timeout
io_uring: revert "io_uring: optimize submit_and_wait API"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Add R_390_GLOB_DAT relocation type support. This fixes boot problem
on linux-next.
- Fix memory leak in zcrypt
* tag 's390-5.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kaslr: add support for R_390_GLOB_DAT relocation type
s390/zcrypt: fix memleak at release
|
|
Pull dma-mapping fix from Christoph Hellwig:
"Fix a regression in the intel-iommu get_required_mask conversion
(Arvind Sankar)"
* tag 'dma-mapping-5.4-2' of git://git.infradead.org/users/hch/dma-mapping:
iommu/vt-d: Return the correct dma mask when we are bypassing the IOMMU
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A fix for st1232 driver to properly report coordinates for 2nd and
subsequent fingers when more than one is on the surface"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: st1232 - fix reporting multitouch coordinates
|
|
nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.
This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.
Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This driver is using regulator_get_optional() to handle all the supplies
that it handles, and only ever enables and disables all supplies en masse
without ever doing any other configuration of the device to handle missing
power. These are clear signs that the API is being misused - it should only
be used for supplies that may be physically absent from the system and in
these cases the hardware usually needs different configuration if the
supply is missing. Instead use normal regualtor_get(), if the supply is
not described in DT then the framework will substitute a dummy regulator in
so no special handling is needed by the consumer driver.
In the case of the PHY regulator the handling in the driver is a hack to
deal with integrated PHYs; the supplies are only optional in the sense
that that there's some confusion in the code about where they're bound to.
From a code point of view they function exactly as normal supplies so can
be treated as such. It'd probably be better to model this by instantiating
a PHY object for integrated PHYs.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We hit the following warning in production
print_req_error: I/O error, dev nbd0, sector 7213934408 flags 80700
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 25 PID: 32407 at lib/refcount.c:190 refcount_sub_and_test_checked+0x53/0x60
Workqueue: knbd-recv recv_work [nbd]
RIP: 0010:refcount_sub_and_test_checked+0x53/0x60
Call Trace:
blk_mq_free_request+0xb7/0xf0
blk_mq_complete_request+0x62/0xf0
recv_work+0x29/0xa1 [nbd]
process_one_work+0x1f5/0x3f0
worker_thread+0x2d/0x3d0
? rescuer_thread+0x340/0x340
kthread+0x111/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x1f/0x30
---[ end trace b079c3c67f98bb7c ]---
This was preceded by us timing out everything and shutting down the
sockets for the device. The problem is we had a request in the queue at
the same time, so we completed the request twice. This can actually
happen in a lot of cases, we fail to get a ref on our config, we only
have one connection and just error out the command, etc.
Fix this by checking cmd->status in nbd_read_stat. We only change this
under the cmd->lock, so we are safe to check this here and see if we've
already error'ed this command out, which would indicate that we've
completed it as well.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We already do this for the most part, except in timeout and clear_req.
For the timeout case we take the lock after we grab a ref on the config,
but that isn't really necessary because we're safe to touch the cmd at
this point, so just move the order around.
For the clear_req cause this is initiated by the user, so again is safe.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A slightly larger set of fixes have accrued in the last two weeks.
Mostly a collection of the usual smaller fixes:
- Marvell Armada: USB phy setup issues on Turris Mox
- Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus
width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some
maintainer updates.
- OMAP: Fixlets for display config, interrupt settings for wifi, some
clock/PM pieces. Also IOMMU regression fix and a ti-sysc
no-watchdog regression fix.
- i.MX: A few fixes around PM/settings, some devicetree fixlets and
catching up with config option changes in DRM
- Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display
panel settings
... and some smaller fixes for Davinci (backlight, McBSP DMA),
Allwinner (phy regulators, PMU removal on A64, etc)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
MAINTAINERS: Update the Spreadtrum SoC maintainer
MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
ARM: davinci_all_defconfig: enable GPIO backlight
ARM: davinci: dm365: Fix McBSP dma_slave_map entry
ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
mailmap: Add Simon Arlott (replacement for expired email address)
arm64: dts: rockchip: Fix override mode for rk3399-kevin panel
...
|
|
Pull drm fixes from Dave Airlie:
"Quiet week this week, which I suspect means some people just didn't
get around to sending me fixes pulls in time. This has 2 komeda and a
bunch of amdgpu fixes in it:
komeda:
- typo fixes
- flushing pipes fix
amdgpu:
- Fix suspend/resume issue related to multi-media engines
- Fix memory leak in user ptr code related to hmm conversion
- Fix possible VM faults when allocating page table memory
- Fix error handling in bo list ioctl"
* tag 'drm-fixes-2019-10-25' of git://anongit.freedesktop.org/drm/drm:
drm/komeda: Fix typos in komeda_splitter_validate
drm/komeda: Don't flush inactive pipes
drm/amdgpu/vce: fix allocation size in enc ring test
drm/amdgpu: fix error handling in amdgpu_bo_list_create
drm/amdgpu: fix potential VM faults
drm/amdgpu: user pages array memory leak fix
drm/amdgpu/vcn: fix allocation size in enc ring test
drm/amdgpu/uvd7: fix allocation size in enc ring test (v2)
drm/amdgpu/uvd6: fix allocation size in enc ring test (v2)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC host fixes:
- mxs: Fix flags passed to dmaengine_prep_slave_sg
- cqhci: Add a missing memory barrier
- sdhci-omap: Fix tuning procedure for temperatures < -20C"
* tag 'mmc-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: fix flags passed to dmaengine_prep_slave_sg
mmc: cqhci: Commit descriptors before setting the doorbell
mmc: sdhci-omap: Fix Tuning procedure for temperatures < -20C
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull the second lot of irqchip updates for 5.4 from Marc Zyngier:
- Sifive PLIC: force driver to skip non-relevant contexts
- GICv4: Don't send VMOVP commands to ITSs that don't have
this vPE mapped
|
|
Modify plic_init() to skip .dts interrupt contexts other
than supervisor external interrupt.
The .dts entry for plic may specify multiple interrupt contexts.
For example, it may assign two entries IRQ_M_EXT and IRQ_S_EXT,
in that order, to the same interrupt controller. This patch
modifies plic_init() to skip the IRQ_M_EXT context since
IRQ_S_EXT is currently the only supported context.
If IRQ_M_EXT is not skipped, plic_init() will report "handler
already present for context" when it comes across the IRQ_S_EXT
context in the next iteration of its loop.
Without this patch, .dts would have to be edited to replace the
value of IRQ_M_EXT with -1 for it to be skipped.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # arch/riscv
Link: https://lkml.kernel.org/r/1571933503-21504-1-git-send-email-alan.mikhak@sifive.com
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-10-23:
amdgpu:
- Fix suspend/resume issue related to multi-media engines
- Fix memory leak in user ptr code related to hmm conversion
- Fix possible VM faults when allocating page table memory
- Fix error handling in bo list ioctl
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191024031809.3155-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Two fixes for komeda, one for typos and one to prevent an hardware issue
when flushing inactive pipes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191023112643.evpp6f23mpjwdsn4@gilmour
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"A couple more DT fixes for 5.4: fix a ref count, memory leak, and
Risc-V cpu schema warnings"
* tag 'devicetree-fixes-for-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: reserved_mem: add missing of_node_put() for proper ref-counting
of: unittest: fix memory leak in unittest_data_add
dt-bindings: riscv: Fix CPU schema errors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix locking issue in the error code path of a function that belongs to
the sysfs interface exposed by the ACPI NFIT handling code (Dan
Carpenter)"
* tag 'acpi-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: NFIT: Fix unlock on error in scrub_show()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix problems related to frequency limits management in cpufreq
that were introduced during the 5.3 cycle (when PM QoS had started to
be used for that), fix a few issues in the OPP (operating performance
points) library code and fix up the recently added haltpoll cpuidle
driver.
The cpufreq changes are somewhat bigger that I would like them to be
at this stage of the cycle, but the problems fixed by them include
crashes on boot and shutdown in some cases (among other things) and in
my view it is better to address the root of the issue right away.
Specifics:
- Using device PM QoS of CPU devices for managing frequency limits in
cpufreq does not work, so introduce frequency QoS (based on the
original low-level PM QoS) for this purpose, switch cpufreq and
related code over to using it and fix a race involving deferred
updates of frequency limits on top of that (Rafael Wysocki, Sudeep
Holla).
- Avoid calling regulator_enable()/disable() from the OPP framework
to avoid side-effects on boot-enabled regulators that may change
their initial voltage due to performing initial voltage balancing
without all restrictions from the consumers (Marek Szyprowski).
- Avoid a kref management issue in the OPP library code and drop an
incorrectly added lockdep_assert_held() from it (Viresh Kumar).
- Make the recently added haltpoll cpuidle driver take the 'idle='
override into account as appropriate (Zhenzhong Duan)"
* tag 'pm-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Reinitialize the list_kref before adding the static OPPs again
cpufreq: Cancel policy update work scheduled before freeing
cpuidle: haltpoll: Take 'idle=' override into account
opp: core: Revert "add regulators enable and disable"
PM: QoS: Drop frequency QoS types from device PM QoS
cpufreq: Use per-policy frequency QoS
PM: QoS: Introduce frequency QoS
opp: of: drop incorrect lockdep_assert_held()
|
|
Remove the following warning:
drivers/i2c/busses/i2c-stm32f7.c:315:
warning: cannot understand function prototype:
'struct stm32f7_i2c_spec i2c_specs[] =
Replace a comment starting with /** by simply /* to avoid having
it interpreted as a kernel-doc comment.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
remains set until next master xfer (e.g. when STOPIE irq get unmasked).
In this case, completion is generated too early: immediately upon new
transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
stretches the SCL line: the bus gets busy until a future master transfer
triggers the bus busy / recovery mechanism (this can take time... and
may never happen at all)
So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.
[1] https://www.kernel.org/doc/Documentation/i2c/slave-interface
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since commit abf4923e97c3 ("i2c: mediatek: disable zero-length transfers
for mt8183"), there is a NULL pointer dereference for all the SoCs
that don't have any quirk. mtk_i2c_functionality is not checking that
the quirks pointer is not NULL before starting to use it.
This commit add a call to i2c_check_quirks which will check whether
the quirks pointer is set, and if so will check if the IP has the
NO_ZERO_LEN quirk.
Fixes: abf4923e97c3 ("i2c: mediatek: disable zero-length transfers for mt8183")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Cengiz Can <cengiz@kernel.wtf>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Ulrich Hecht <uli@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On a system without Single VMOVP support (say GITS_TYPER.VMOVP == 0),
we will map vPEs only on ITSs that will actually control interrupts
for the given VM. And when moving a vPE, the VMOVP command will be
issued only for those ITSs.
But when issuing VMOVPs we seemed fail to present the exact ITSList
to ITSs who are actually included in the synchronization operation.
The its_list_map we're currently using includes all ITSs in the system,
even though some of them don't have the corresponding vPE mapping at all.
Introduce get_its_list() to get the per-VM its_list_map, to indicate
which ITSs have vPE mappings for the given VM, and use this map as
the expected ITSList when building VMOVP. This is hopefully a performance
gain not to do some synchronization with those unsuspecting ITSs.
And initialize the whole command descriptor to zero at beginning, since
the seq_num and its_list should be RES0 when GITS_TYPER.VMOVP == 1.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571802386-2680-1-git-send-email-yuzenghui@huawei.com
|
|
* pm-cpuidle:
cpuidle: haltpoll: Take 'idle=' override into account
* pm-opp:
opp: Reinitialize the list_kref before adding the static OPPs again
opp: core: Revert "add regulators enable and disable"
opp: of: drop incorrect lockdep_assert_held()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fix from Lee Jones:
"Fix broken support for BananaPi-r2"
* tag 'mfd-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: mt6397: Fix probe after changing mt6397-core
|
|
Part 3 from this series [1] was not merged due to wrong splitting
and breaks mt6323 pmic on bananapi-r2
dmesg prints this line and at least switch is not initialized on bananapi-r2
mt6397 1000d000.pwrap:mt6323: unsupported chip: 0x0
this patch contains only the probe-changes and chip_data structs
from original part 3 by Hsin-Hsiung Wang
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=164155
Fixes: a4872e80ce7d ("mfd: mt6397: Extract IRQ related code from core driver")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit d698a388146c ("of: reserved-memory: ignore disabled memory-region
nodes") added an early return in of_reserved_mem_device_init_by_idx(), but
didn't call of_node_put() on a device_node whose ref-count was incremented
in the call to of_parse_phandle() preceding the early exit.
Fixes: d698a388146c ("of: reserved-memory: ignore disabled memory-region nodes")
Signed-off-by: Chris Goldsworthy <cgoldswo@codeaurora.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
In unittest_data_add, a copy buffer is created via kmemdup. This buffer
is leaked if of_fdt_unflatten_tree fails. The release for the
unittest_data buffer is added.
Fixes: b951f9dc7f25 ("Enabling OF selftest to run without machine's devicetree")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pull VFIO fixlet from Alex Williamson:
"Fix (false) uninitialized variable warning (Joerg Roedel)"
* tag 'vfio-v5.4-rc5' of git://github.com/awilliam/linux-vfio:
vfio/type1: Initialize resv_msi_base
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"There are a few core fixes here around error handling and handling if
suspend mode configuration and some driver specific fixes here but the
most important change is the fix to the fixed-regulator DT schema
conversion introduced during the last merge window.
That fixes one of the last two errors preventing successful execution
of "make dt_binding_check" which will be enormously helpful for DT
schema development"
* tag 'regulator-fix-v5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
regulator: lochnagar: Add on_off_delay for VDDCORE
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
regulator: da9062: fix suspend_enable/disable preparation
dt-bindings: fixed-regulator: fix compatible enum
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
regulator: core: make regulator_register() EPROBE_DEFER aware
regulator: of: fix suspend-min/max-voltage parsing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Three fixes for omaps for v5.4-rc cycle
Two regression fixes for omap3 iommu. I missed applying two omap3
related iommu pdata quirks patches earlier because the kbuild test
robot produced errors on them for missing dependencies.
Fix ti-sysc interconnect target module driver handling for watchdog
quirk. I must have tested this earlier only with watchdog service
running, but clearly it does not do what it needs to do.
* tag 'omap-for-v5.4/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix watchdog quirk handling
ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU
ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs
Link: https://lore.kernel.org/r/pull-1571848757-282222@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
:Pull ARM fixes from Russell King:
- fix for alignment faults under high memory pressure
- use u32 for ARM instructions in fault handler
- mark functions that must always be inlined with __always_inline
- fix for nommu XIP
- fix ARMv7M switch to handler mode in reboot path
- fix the recently introduced AMBA reset control error paths
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8926/1: v7m: remove register save to stack before svc
ARM: 8914/1: NOMMU: Fix exc_ret for XIP
ARM: 8908/1: add __always_inline to functions called from __get_user_check()
ARM: mm: alignment: use "u32" for 32-bit instructions
ARM: mm: fix alignment handler faults under memory pressure
drivers/amba: fix reset control error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
"Fix ghes_edac UAF case triggered by KASAN and DEBUG_TEST_DRIVER_REMOVE.
Future pending rework of the ghes_edac instances registration will do
away with the single memory controller per system model and that ugly
hackery there.
This is a minimal fix for stable@, courtesy of James Morse"
* tag 'edac_urgent_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/ghes: Fix Use after free in ghes_edac remove path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) framework fixes for v5.4
from Viresh Kumar:
"This contains:
- Patch to revert addition of regulator enable/disable in OPP core
(Marek).
- Remove incorrect lockdep assert (Viresh).
- Fix a kref counting issue (Viresh)."
* 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Reinitialize the list_kref before adding the static OPPs again
opp: core: Revert "add regulators enable and disable"
opp: of: drop incorrect lockdep_assert_held()
|
|
The list_kref reaches a count of 0 when all the static OPPs are removed,
for example when dev_pm_opp_of_cpumask_remove_table() is called, though
the actual OPP table may not get freed as it may still be referenced by
other parts of the kernel, like from a call to
dev_pm_opp_set_supported_hw(). And if we call
dev_pm_opp_of_cpumask_add_table() again at this point, we must
reinitialize the list_kref otherwise the kernel will hit a WARN() in
kref infrastructure for incrementing a kref with value 0.
Fixes: 11e1a1648298 ("opp: Don't decrement uninitialized list_kref")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
|
|
Scheduled policy update work may end up racing with the freeing of the
policy and unregistering the driver.
One possible race is as below, where the cpufreq_driver is unregistered,
but the scheduled work gets executed at later stage when, cpufreq_driver
is NULL (i.e. after freeing the policy and driver).
Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = (ptrval)
[0000001c] *pgd=80000080204003, *pmd=00000000
Internal error: Oops: 206 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 34 Comm: kworker/0:1 Not tainted 5.4.0-rc3-00006-g67f5a8081a4b #86
Hardware name: ARM-Versatile Express
Workqueue: events handle_update
PC is at cpufreq_set_policy+0x58/0x228
LR is at dev_pm_qos_read_value+0x77/0xac
Control: 70c5387d Table: 80203000 DAC: fffffffd
Process kworker/0:1 (pid: 34, stack limit = 0x(ptrval))
(cpufreq_set_policy) from (refresh_frequency_limits.part.24+0x37/0x48)
(refresh_frequency_limits.part.24) from (handle_update+0x2f/0x38)
(handle_update) from (process_one_work+0x16d/0x3cc)
(process_one_work) from (worker_thread+0xff/0x414)
(worker_thread) from (kthread+0xff/0x100)
(kthread) from (ret_from_fork+0x11/0x28)
Fixes: 67d874c3b2c6 ("cpufreq: Register notifiers with the PM QoS framework")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
[ rjw: Cancel the work before dropping the QoS requests ]
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If a process is interrupted while accessing the crypto device and the
global ap_perms_mutex is contented, release() could return early and
fail to free related resources.
Fixes: 00fab2350e6b ("s390/zcrypt: multiple zcrypt device nodes support")
Cc: <stable@vger.kernel.org> # 4.19
Cc: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a bunch of pin control fixes. I was lagging behind on this
one, some fixes should have come in earlier, sorry about that.
Anyways here it is, pretty straight-forward fixes, the Strago fix
stand out as something serious affecting a lot of machines.
Summary:
- Handle multiple instances of Intel chips without complaining.
- Restore the Intel Strago DMI workaround
- Make the Armada 37xx handle pins over 32
- Fix the polarity of the LED group on Armada 37xx
- Fix an off-by-one bug in the NS2 driver
- Fix error path for iproc's platform_get_irq()
- Fix error path on the STMFX driver
- Fix a typo in the Berlin AS370 driver
- Fix up misc errors in the Aspeed 2600 BMC support
- Fix a stray SPDX tag"
* tag 'pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed-g6: Rename SD3 to EMMC and rework pin groups
pinctrl: aspeed-g6: Fix UART13 group pinmux
pinctrl: aspeed-g6: Make SIG_DESC_CLEAR() behave intuitively
pinctrl: aspeed-g6: Fix I3C3/I3C4 pinmux configuration
pinctrl: aspeed-g6: Fix I2C14 SDA description
pinctrl: aspeed-g6: Sort pins for sanity
dt-bindings: pinctrl: aspeed-g6: Rework SD3 function and groups
pinctrl: berlin: as370: fix a typo s/spififib/spdifib
pinctrl: armada-37xx: swap polarity on LED group
pinctrl: stmfx: fix null pointer on remove
pinctrl: iproc: allow for error from platform_get_irq()
pinctrl: ns2: Fix off by one bugs in ns2_pinmux_enable()
pinctrl: bcm-iproc: Use SPDX header
pinctrl: armada-37xx: fix control of pins 32 and up
pinctrl: cherryview: restore Strago DMI workaround for all versions
pinctrl: intel: Allocate IRQ chip dynamic
|
|
Currenly haltpoll isn't aware of the 'idle=' override, the priority is
'idle=poll' > haltpoll > 'idle=halt'. When 'idle=poll' is used, cpuidle
driver is bypassed but current_driver in sys still shows 'haltpoll'.
When 'idle=halt' is used, haltpoll takes precedence and makes
'idle=halt' have no effect.
Add a check to prevent the haltpoll driver from loading if 'idle=' is
present.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Co-developed-by: Joao Martins <joao.m.martins@oracle.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We change the locking in this function and forgot to update this error
path so we are accidentally still holding the "dev->lockdep_mutex".
Fixes: 87a30e1f05d7 ("driver-core, libnvdimm: Let device subsystems add local lockdep coverage")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: 5.3+ <stable@vger.kernel.org> # 5.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.4:
- Re-enable SNVS power key for imx6q-logicpd board which was accidentally
disabled by a SoC level change.
- Fix I2C switches on vf610-zii-scu4-aib board by specifying property
i2c-mux-idle-disconnect.
- A fix on imx-scu API that reads UID from firmware to avoid kernel NULL
pointer dump.
- A series from Anson to correct i.MX7 GPT and i.MX8 USDHC IPG clock.
- A fix on DRM_MSM Kconfig regression on i.MX5 by adding the option
explicitly into imx_v6_v7_defconfig.
- Fix ARM regulator states issue for zii-ultra board, which is impacting
stability of the board.
- A correction on CPU core idle state name for LayerScape LX2160A SoC.
* tag 'imx-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM
arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk
arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk
ARM: dts: imx7s: Correct GPT's ipg clock source
ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect'
ARM: dts: imx6q-logicpd: Re-Enable SNVS power key
arm64: dts: lx2160a: Correct CPU core idle state name
arm64: dts: zii-ultra: fix ARM regulator states
soc: imx: imx-scu: Getting UID from SCU should have response
Link: https://lore.kernel.org/r/20191017141851.GA22506@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For Sitronix st1633 multi-touch controller driver the coordinates reported
for multiple fingers were wrong, as it was always taking LSB of coordinates
from the first contact data.
Signed-off-by: Dixit Parmar <dixitparmar19@gmail.com>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Cc: stable@vger.kernel.org
Fixes: 351e0592bfea ("Input: st1232 - add support for st1633")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204561
Link: https://lore.kernel.org/r/1566209314-21767-1-git-send-email-dixitparmar19@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
