summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2012-02-13drm/i915: Fix TV Out refresh rate.Rodrigo Vivi
commit 23bd15ec662344dc10e9918fdd0dbc58bc71526d upstream. TV Out refresh rate was half of the specification for almost all modes. Due to this reason pixel clock was so low for some modes causing flickering screen. Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/i915: check ACTHD of all ringsDaniel Vetter
commit 097354eb14fa94d31a09c64d640643f58e4a5a9a upstream. Otherwise hangcheck spuriously fires when running blitter/bsd-only workloads. Contrary to a similar patch by Ben Widawsky this does not check INSTDONE of the other rings. Chris Wilson implied that in a failure to detect a hang, most likely because INSTDONE was fluctuating. Thus only check ACTHD, which as far as I know is rather reliable. Also, blitter and bsd rings can't launch complex tasks from a single instruction (like 3D_PRIM on the render with complex or even infinite shaders). This fixes spurious gpu hang detection when running tests/gem_hangcheck_forcewake on snb/ivb. Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/i915: DisplayPort hot remove notification to audio driverWu Fengguang
commit 832afda6a7d7235ef0e09f4ec46736861540da6d upstream. On DP monitor hot remove, clear DP_AUDIO_OUTPUT_ENABLE accordingly, so that the audio driver will receive hot plug events and take action to refresh its device state and ELD contents. Note that the DP_AUDIO_OUTPUT_ENABLE bit may be enabled or disabled only when the link training is complete and set to "Normal". Tested OK for both hot plug/remove and DPMS on/off. Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/i915: HDMI hot remove notification to audio driverWu Fengguang
commit 2deed761188d7480eb5f7efbfe7aa77f09322ed8 upstream. On HDMI monitor hot remove, clear SDVO_AUDIO_ENABLE accordingly, so that the audio driver will receive hot plug events and take action to refresh its device state and ELD contents. The cleared SDVO_AUDIO_ENABLE bit needs to be restored to prevent losing HDMI audio after DPMS on. CC: Wang Zhenyu <zhenyu.z.wang@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/radeon/kms: disable output polling when suspendedSeth Forshee
commit 86698c20f71d488b32c49ed4687fb3cf8a88a5ca upstream. Polling the outputs when the device is suspended can result in erroneous status updates. Disable output polling during suspend to prevent this from happening. Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/nouveau/gem: fix fence_sync race / oopsBen Skeggs
commit 525895ba388c949aa906f26e3ec5cb1ab041f56b upstream. Due to a race it was possible for a fence to be destroyed while another thread was trying to synchronise with it. If this happened in the fallback non-semaphore path, it lead to the following oops due to fence->channel being NULL. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<fa9632ce>] nouveau_fence_update+0xe/0xe0 [nouveau] *pde = a649c067 SMP Modules linked in: fuse nouveau(O) ttm(O) drm_kms_helper(O) drm(O) mxm_wmi video wmi netconsole configfs lockd bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack ip6table_filter ip6_tables snd_hda_codec_realtek snd_hda_intel snd_hda_cobinfmt_misc uinput ata_generic pata_acpi pata_aet2c_algo_bit i2c_core [last unloaded: wmi] Pid: 2255, comm: gnome-shell Tainted: G O 3.2.0-0.rc5.git0.1.fc17.i686 #1 System manufacturer System Product Name/M2A-VM EIP: 0060:[<fa9632ce>] EFLAGS: 00010296 CPU: 1 EIP is at nouveau_fence_update+0xe/0xe0 [nouveau] EAX: 00000000 EBX: ddfc6dd0 ECX: dd111580 EDX: 00000000 ESI: 00003e80 EDI: dd111580 EBP: dd121d00 ESP: dd121ce8 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process gnome-shell (pid: 2255, ti=dd120000 task=dd111580 task.ti=dd120000) Stack: 7dc86c76 00000000 00003e80 ddfc6dd0 00003e80 dd111580 dd121d0c fa96371f 00000000 dd121d3c fa963773 dd111580 01000246 000ec53d 00000000 ddfc6dd0 00001f40 00000000 ddfc6dd0 00000010 dc7df840 dd121d6c fa9639a0 00000000 Call Trace: [<fa96371f>] __nouveau_fence_signalled+0x1f/0x30 [nouveau] [<fa963773>] __nouveau_fence_wait+0x43/0xd0 [nouveau] [<fa9639a0>] nouveau_fence_sync+0x1a0/0x1c0 [nouveau] [<fa964046>] validate_list+0x176/0x300 [nouveau] [<f7d9c9c0>] ? ttm_bo_mem_put+0x30/0x30 [ttm] [<fa964b8a>] nouveau_gem_ioctl_pushbuf+0x48a/0xfd0 [nouveau] [<c0406481>] ? die+0x31/0x80 [<f7c93d98>] drm_ioctl+0x388/0x490 [drm] [<c0406481>] ? die+0x31/0x80 [<fa964700>] ? nouveau_gem_ioctl_new+0x150/0x150 [nouveau] [<c0635c7b>] ? file_has_perm+0xcb/0xe0 [<f7c93a10>] ? drm_copy_field+0x80/0x80 [drm] [<c0564f56>] do_vfs_ioctl+0x86/0x5b0 [<c0406481>] ? die+0x31/0x80 [<c0635f22>] ? selinux_file_ioctl+0x62/0x130 [<c0554f30>] ? fget_light+0x30/0x340 [<c05654ef>] sys_ioctl+0x6f/0x80 [<c099e3a4>] syscall_call+0x7/0xb [<c0406481>] ? die+0x31/0x80 [<c0406481>] ? die+0x31/0x80 Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.Michel Dänzer
commit 1b61925061660009f5b8047f93c5297e04541273 upstream. The value of this register is transferred to the V_COUNTER register at the beginning of vertical blank. V_COUNTER is the reference for VLINE waits and goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout, so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the beginning of vertical blank, and VLINE waits excluding the whole scanout area could never finish (possibly only if VIEWPORT_Y_START is larger than the length of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer height should prevent this for any kind of VLINE wait. Fixes https://bugs.freedesktop.org/show_bug.cgi?id=45329 . Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13at_hdmac: bugfix for enabling channel irqNikolaus Voss
commit bda3a47c886664e86ee14eb79e9072b9e341f575 upstream. commit 463894705e4089d0ff69e7d877312d496ac70e5b deleted redundant chan_id and chancnt initialization in dma drivers as this is done in dma_async_device_register(). However, atc_enable_irq() relied on chan_id set before registering the device, what left only channel 0 functional for this driver. This patch introduces atc_enable/disable_chan_irq() as a variant of atc_enable/disable_irq() with the channel as explicit argument. Signed-off-by: Nikolaus Voss <n.voss@weinmann.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13IB/mlx4: pass SMP vendor-specific attribute MADs to firmwareJack Morgenstein
commit a6f7feae6d19e84253918d88b04153af09d3a243 upstream. In the current code, vendor-specific MADs (e.g with the FDR-10 attribute) are silently dropped by the driver, resulting in timeouts at the sending side and inability to query/configure the relevant feature. However, the ConnectX firmware is able to handle such MADs. For unsupported attributes, the firmware returns a GET_RESPONSE MAD containing an error status. For example, for a FDR-10 node with LID 11: # ibstat mlx4_0 1 CA: 'mlx4_0' Port 1: State: Active Physical state: LinkUp Rate: 40 (FDR10) Base lid: 11 LMC: 0 SM lid: 24 Capability mask: 0x02514868 Port GUID: 0x0002c903002e65d1 Link layer: InfiniBand Extended Port Query (EPI) vendor mad timeouts before the patch: # smpquery MEPI 11 -d ibwarn: [4196] smp_query_via: attr 0xff90 mod 0x0 route Lid 11 ibwarn: [4196] _do_madrpc: retry 1 (timeout 1000 ms) ibwarn: [4196] _do_madrpc: retry 2 (timeout 1000 ms) ibwarn: [4196] _do_madrpc: timeout after 3 retries, 3000 ms ibwarn: [4196] mad_rpc: _do_madrpc failed; dport (Lid 11) smpquery: iberror: [pid 4196] main: failed: operation EPI: ext port info query failed EPI query works OK with the patch: # smpquery MEPI 11 -d ibwarn: [6548] smp_query_via: attr 0xff90 mod 0x0 route Lid 11 ibwarn: [6548] mad_rpc: data offs 64 sz 64 mad data 0000 0000 0000 0001 0000 0001 0000 0001 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 # Ext Port info: Lid 11 port 0 StateChangeEnable:...............0x00 LinkSpeedSupported:..............0x01 LinkSpeedEnabled:................0x01 LinkSpeedActive:.................0x01 Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Ira Weiny <weiny2@llnl.gov> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13firewire: ohci: disable MSI on Ricoh controllersStefan Richter
commit 320cfa6ce0b3dc794fedfa4bae54c0f65077234d upstream. The PCIe device FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd FireWire Host Controller [1180:e832] (prog-if 10 [OHCI]) is unable to access attached FireWire devices when MSI is enabled but works if MSI is disabled. http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html Hence add the "disable MSI" quirks flag for this device, or in fact for safety and simplicity for all current (R5U230, R5U231, R5U240) and future Ricoh PCIe 1394 controllers. Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13firewire: ohci: add reset packet quirk for SB AudigyClemens Ladisch
commit d1bb399ad03c11e792f6dea198d3b1e23061f094 upstream. The Audigy's SB1394 controller is actually from Texas Instruments and has the same bus reset packet generation bug, so it needs the same quirk entry. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-13drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layerSamuel Thibault
commit cbcb8346054073d000ecac324763372d6abd44ac upstream. KDFONTOP(GET) currently fails with EIO when being run in a 32bit userland with a 64bit kernel if the font width is not 8. This is because of the setting of the KD_FONT_FLAG_OLD flag, which makes con_font_get return EIO in such case. This flag should *not* be set for KDFONTOP, since it's actually the whole point of this flag (see comment in con_font_set for instance). Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Cc: Arthur Taylor <art@ified.ca> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-06PCI: Rework ASPM disable codeMatthew Garrett
commit 3c076351c4027a56d5005a39a0b518a4ba393ce2 upstream. Right now we forcibly clear ASPM state on all devices if the BIOS indicates that the feature isn't supported. Based on the Microsoft presentation "PCI Express In Depth for Windows Vista and Beyond", I'm starting to think that this may be an error. The implication is that unless the platform grants full control via _OSC, Windows will not touch any PCIe features - including ASPM. In that case clearing ASPM state would be an error unless the platform has granted us that control. This patch reworks the ASPM disabling code such that the actual clearing of state is triggered by a successful handoff of PCIe control to the OS. The general ASPM code undergoes some changes in order to ensure that the ability to clear the bits isn't overridden by ASPM having already been disabled. Further, this theoretically now allows for situations where only a subset of PCIe roots hand over control, leaving the others in the BIOS state. It's difficult to know for sure that this is the right thing to do - there's zero public documentation on the interaction between all of these components. But enough vendors enable ASPM on platforms and then set this bit that it seems likely that they're expecting the OS to leave them alone. Measured to save around 5W on an idle Thinkpad X220. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: allow more baud rates above 1MbaudJohan Hovold
commit d1620ca9e7bb0030068c3b45b653defde8839dac upstream. Allow more baud rates to be set in [1M,2M] baud. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: initialise baud rate at openJohan Hovold
commit cdc32fd6f7b2b2580d7f1b74563f888e4dd9eb8a upstream. The newer cp2104 devices require the baud rate to be initialised after power on. Make sure it is set when port is opened. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: clean up, refactor and document speed handlingJohan Hovold
commit e5990874e511d5bbca23b3396419480cb2ca0ee7 upstream. Clean up and refactor speed handling. Document baud rate handling for CP210{1,2,4,5,10}. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: fix up set_termios variablesJohan Hovold
commit 34b76fcaee574017862ea3fa0efdcd77a9d0e57d upstream. [Based on a patch from Johan, mangled by gregkh to keep things in line] Fix up the variable usage in the set_termios call. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: do not map baud rates to B0Johan Hovold
commit be125d9c8d59560e7cc2d6e2b65c8fd233498ab7 upstream. We do not implement B0 hangup yet so map low baudrates to 300bps. Signed-off-by: Johan Hovold <jhovold@gmail.com> Cc: Preston Fick <preston.fick@silabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: fix CP2104 baudrate usagePreston Fick
commit 7f482fc88ac47662228d6b1f05759797c8936a30 upstream. This fix changes the way baudrates are set on the CP210x devices from Silicon Labs. The CP2101/2/3 will respond to both a GET/SET_BAUDDIV command, and GET/SET_BAUDRATE command, while CP2104 and higher devices only respond to GET/SET_BAUDRATE. The current cp210x.ko driver in kernel version 3.2.0 only implements the GET/SET_BAUDDIV command. This patch implements the two new codes for the GET/SET_BAUDRATE commands. Then there is a change in the way that the baudrate is assigned or retrieved. This is done according to the CP210x USB specification in AN571. This document can be found here: http://www.silabs.com/pages/DownloadDoc.aspx?FILEURL=Support%20Documents/TechnicalDocs/AN571.pdf&src=DocumentationWebPart Sections 5.3/5.4 describe the USB packets for the old baudrate method. Sections 5.5/5.6 describe the USB packets for the new method. This patch also implements the new request scheme, and eliminates the unnecessary baudrate calculations since it uses the "actual baudrate" method. This patch solves the problem reported for the CP2104 in bug 42586, and also keeps support for all other devices (CP2101/2/3). This patchfile is also attached to the bug report on bugzilla.kernel.org. This patch has been developed and test on the 3.2.0 mainline kernel version under Ubuntu 10.11. Signed-off-by: Preston Fick <preston.fick@silabs.com> [duplicate patch also sent by Johan - gregkh] Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cp210x: call generic open last in openJohan Hovold
commit 55b2afbb92ad92e9f6b0aa4354eb1c94589280c3 upstream. Make sure port is fully initialised before calling generic open. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: serial: CP210x: Added USB-ID for the Link Instruments MSO-19Renato Caldas
commit 791b7d7cf69de11275e4dccec2f538eec02cbff6 upstream. This device is a Oscilloscope/Logic Analizer/Pattern Generator/TDR, using a Silabs CP2103 USB to UART Bridge. Signed-off-by: Renato Caldas <rmsc@fe.up.pt> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03bonding: fix enslaving in alb mode when link downJiri Bohac
[ Upstream commit b924551bed09f61b64f21bffe241afc5526b091a ] bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC address. This is done differently for TLB and ALB modes. bond->alb_info.rlb_enabled is used to discriminate between the two modes but this flag may be uninitialized if the slave is being enslaved prior to calling bond_open() -> bond_alb_initialize() on the master. It turns out all the callers of alb_set_slave_mac_addr() pass bond->alb_info.rlb_enabled as the hw parameter. This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and makes the function decide based on the bonding mode instead, which fixes the above problem. Reported-by: Narendra K <Narendra_K@Dell.com> Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPEBjørn Mork
commit 15699e6fafc3a90e5fdc2ef30555a04dee62286f upstream. The probe does not strictly require the USB_CDC_DMM_TYPE descriptor, which is a good thing as it makes the driver usable on non-conforming interfaces. A user could e.g. bind to it to a CDC ECM interface by using the new_id and bind sysfs files. But this would fail with a 0 buffer length due to the missing descriptor. Fix by defining a reasonable fallback size: The minimum device receive buffer size required by the CDC WMC standard, revision 1.1 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cdc-wdm: better allocate a buffer that is at least as big as we tell ↵Bjørn Mork
the USB core commit 655e247daf52b202a6c2d0f8a06dd2051e756ce4 upstream. As it turns out, there was a mismatch between the allocated inbuf size (desc->bMaxPacketSize0, typically something like 64) and the length we specified in the URB (desc->wMaxCommand, typically something like 2048) Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removalBjørn Mork
commit 62aaf24dc125d7c55c93e313d15611f152b030c7 upstream. wdm_disconnect() waits for the mutex held by wdm_read() before calling wake_up_all(). This causes a deadlock, preventing device removal to complete. Do the wake_up_all() before we start waiting for the locks. Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Oliver Neukum <oliver@neukum.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03hwmon: (sht15) fix bad error codeVivien Didelot
commit 6edf3c30af01854c416f8654d3d5d2652470afd4 upstream. When no platform data was supplied, returned error code was 0. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776FGuenter Roeck
commit ad77c3e1808f07fa70f707b1c92a683b7c7d3f85 upstream. NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt is made to set those pwm channels to DC mode. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03hwmon: (f71805f) Fix clamping of temperature limitsJean Delvare
commit 86b2bbfdbd1fcc4a3aa62ccd3f245c40c5ad5b85 upstream. Properly clamp temperature limits set by the user. Without this fix, attempts to write temperature limits above the maximum supported by the chip (255 degrees Celsius) would arbitrarily and unexpectedly result in the limit being set to 0 degree Celsius. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03xHCI: Cleanup isoc transfer ring when TD length mismatch foundAndiry Xu
commit cf840551a884360841bd3d3ce1ad0868ff0b759a upstream. When a TD length mismatch is found during isoc TRB enqueue, it directly returns -EINVAL. However, isoc transfer is partially enqueued at this time, and the ring should be cleared. This should be backported to kernels as old as 2.6.36, which contain the commit 522989a27c7badb608155b1f1dea3487ed431f74 "xhci: Fix failed enqueue in the middle of isoch TD." Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03xhci: Fix USB 3.0 device restart on resume.Sarah Sharp
commit d0cd5d482b8a6dc92c6c69a5387baf72ea84f23a upstream. The xHCI hub port code gets passed a zero-based port number by the USB core. It then adds one to in order to find a device slot by port number and device speed by calling xhci_find_slot_id_by_port. That function clearly states it requires a one-based port number. The xHCI port status change event handler was using a zero-based port number that it got from find_faked_portnum_from_hw_portnum, not a one-based port number. This lead to the doorbells never being rung for a device after a resume, or worse, a different device with the same speed having its doorbell rung (which could lead to bad power management in the xHCI host controller). This patch should be backported to kernels as old as 2.6.39. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03drivers/usb/host/ehci-fsl.c: add missing iounmapJulia Lawall
commit 2492c6e6454ff3edb11e273b071a6ea80a199c71 upstream. Add missing iounmap in error handling code, in a case where the function already preforms iounmap on some other execution path. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e; statement S,S1; int ret; @@ e = \(ioremap\|ioremap_nocache\)(...) ... when != iounmap(e) if (<+...e...+>) S ... when any when != iounmap(e) *if (...) { ... when != iounmap(e) return ...; } ... when any iounmap(e); // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: usbsevseg: fix max lengthHarrison Metzger
commit 1097ccebe630170080c41df0edcf88e0626e9c75 upstream. This changes the max length for the usb seven segment delcom device to 8 from 6. Delcom has both 6 and 8 variants and having 8 works fine with devices which are only 6. Signed-off-by: Harrison Metzger <harrisonmetz@gmail.com> Signed-off-by: Stuart Pook <stuart@acm.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03vmwgfx: Fix assignment in vmw_framebuffer_create_handleRyan Mallon
commit bf9c05d5b6d19b3e4c9fe21047694e94f48db89b upstream. The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space. Signed-off-by: Ryan Mallon <rmallon@gmail.com> Reviewed-by: Jakob Bornecrantz<jakob@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03jsm: Fixed EEH recovery errorLucas Kannebley Tavares
commit 26aa38cafae0dbef3b2fe75ea487c83313c36d45 upstream. There was an error on the jsm driver that would cause it to be unable to recover after a second error is detected. At the first error, the device recovers properly: [72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0 [72521.485695] EEH: This PCI device has failed 1 times in the last hour: ... [72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm [72532.105689] jsm: Port 3 added However, at the second error, it cascades until EEH disables the device: [72631.229549] Call Trace: ... [72641.725687] jsm: Port 3 added [72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0 [72641.725698] EEH: This PCI device has failed 3 times in the last hour: It was caused because the PCI state was not being saved after the first restore. Therefore, at the second recovery the PCI state would not be restored. Signed-off-by: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by: Breno Leitao <brenohl@br.ibm.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03serial: amba-pl011: lock console writes against interruptsRabin Vincent
commit ef605fdb33883d687cff5ba75095a91b313b4966 upstream. Protect against pl011_console_write() and the interrupt for the console UART running concurrently on different CPUs. Otherwise the console_write could spin for a long time waiting for the UART to become not busy, while the other CPU continuously services UART interrupts and keeps the UART busy. The checks for sysrq and oops_in_progress are taken from 8250.c. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by: Bibek Basu <bibek.basu@stericsson.com> Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03TTY: fix UV serial console regressionJiri Slaby
commit 0eee50af5b13e00b3fb7a5fe8480419a71b8235d upstream. Commit 74c2107759d (serial: Use block_til_ready helper) and its fixup 3f582b8c110 (serial: fix termios settings in open) introduced a regression on UV systems. The serial eventually freezes while being used. It's completely unpredictable and sometimes needs a heap of traffic to happen first. To reproduce this, yast installation was used as it turned out to be pretty reliable in reproducing. Especially during installation process where one doesn't have an SSH daemon running. And no monitor as the HW is completely headless. So this was fun to find. Given the machine doesn't boot on vanilla before 2.6.36 final. (And the commits above are older.) Unless there is some bad race in the code, the hardware seems to be pretty broken. Otherwise pure MSR read should not cause such a bug, or? So to prevent the bug, revert to the old behavior. I.e. read modem status only if we really have to -- for non-CLOCAL set serials. Non-CLOCAL works on this hardware OK, I tried. See? I don't. And document that shit. Signed-off-by: Jiri Slaby <jslaby@suse.cz> References: https://lkml.org/lkml/2011/12/6/573 References: https://bugzilla.novell.com/show_bug.cgi?id=718518 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03usb: io_ti: Make edge_remove_sysfs_attrs the port_remove method.Eric W. Biederman
commit 6d443d8499e4e59ffb949759cdded32730f8d2f6 upstream. Calling edge_remove_sysfs_attrs from edge_disconnect is too late as the device has already been removed from sysfs. Do the simple and obvious thing and make edge_remove_sysfs_attrs the port_remove method. Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Reported-by: Wolfgang Frisch <wfpub@roembden.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03qcaux: add more Pantech UML190 and UML290 portsDan Williams
commit 074cc73506f529f39fef32ad1c9e1d4cdd8acf6c upstream. More ports we now know how to talk to. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cdc-wdm: use two mutexes to allow simultaneous read and writeBjørn Mork
commit e8537bd2c4f325a4796da33564ddcef9489b7feb upstream. using a separate read and write mutex for locking is sufficient to make the driver accept simultaneous read and write. This improves useability a lot. Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: cdc-wdm: updating desc->length must be protected by spin_lockBjørn Mork
commit c428b70c1e115c5649707a602742e34130d19428 upstream. wdm_in_callback() will also touch this field, so we cannot change it without locking Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: ftdi_sio: Add more identifiersAlan Cox
commit 2353f806c97020d4c7709f15eebb49b591f7306d upstream. 0x04d8, 0x000a: Hornby Elite Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: serial: ftdi additional IDsPeter Naulls
commit fc216ec363f4d174932df90bbf35c77d0540e561 upstream. I tested this against 2.6.39 in the Ubuntu kernel, however I see the IDs are not in latest 3.2 git. This adds IDs for the FTDI controller in the Rainforest Automation Zigbee dongle. Signed-off-by: Peter Naulls <peter@chocky.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: ftdi_sio: add PID for TI XDS100v2 / BeagleBone A3Peter Korsgaard
commit 55f13aeae0346f0c89bfface91ad9a97653dc433 upstream. Port A for JTAG, port B for serial. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: ftdi_sio: fix initial baud rateJohan Hovold
commit 108e02b12921078a59dcacd048079ece48a4a983 upstream. Fix regression introduced by commit b1ffb4c851f1 ("USB: Fix Corruption issue in USB ftdi driver ftdi_sio.c") which caused the termios settings to no longer be initialised at open. Consequently it was no longer possible to set the port to the default speed of 9600 baud without first changing to another baud rate and back again. Reported-by: Roland Ramthun <mail@roland-ramthun.de> Signed-off-by: Johan Hovold <jhovold@gmail.com> Tested-by: Roland Ramthun <mail@roland-ramthun.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: ftdi_sio: fix TIOCSSERIAL baud_base handlingJohan Hovold
commit eb833a9e0972f60beb4ab8104ad7ef6bf30f02fc upstream. Return EINVAL if new baud_base does not match the current one. The baud_base is device specific and can not be changed. This restores the old (pre-2005) behaviour which was changed due to a misunderstanding regarding this fact (see https://lkml.org/lkml/2005/1/20/84). Reported-by: Torbjörn Lofterud <torbjorn@pi.nxs.se> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03USB: option: Add LG docomo L-02CKentaro Matsuyama
commit e423d7401fd0717cb56a6cf51dd8341cc3e800d2 upstream. Add vendor and product ID for USB 3G/LTE modem of docomo L-02C Signed-off-by: Kentaro Matsuyama <kentaro.matsuyama@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03drm/i915/sdvo: always set positive sync polarityPaulo Zanoni
commit ba68e086223a5f149f37bf8692c8cdbf1b0ba3ef upstream. This is a revert of 81a14b46846fea0741902e8d8dfcc6c6c78154c8. We already set the mode polarity using the SDVO commands with struct intel_sdvo_dtd. We have at least 3 bugs that get fixed with this patch. The documentation, despite not clear, can also be interpreted in a way that suggests this patch is needed. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=15766 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42174 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43333 Reviewed-by: Eric Anholt <eric@anholt.net> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Keith Packard <keithp@keithp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03drm: Fix authentication kernel crashThomas Hellstrom
commit 598781d71119827b454fd75d46f84755bca6f0c6 upstream. If the master tries to authenticate a client using drm_authmagic and that client has already closed its drm file descriptor, either wilfully or because it was terminated, the call to drm_authmagic will dereference a stale pointer into kmalloc'ed memory and corrupt it. Typically this results in a hard system hang. This patch fixes that problem by removing any authentication tokens (struct drm_magic_entry) open for a file descriptor when that file descriptor is closed. Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-02-03drm/radeon/kms: Add an MSI quirk for Dell RS690Alex Deucher
commit 44517c44496062180a6376cc704b33129441ce60 upstream. Interrupts only work with MSIs. https://bugs.freedesktop.org/show_bug.cgi?id=37679 Reported-by: Dmitry Podgorny <pasis.uax@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-25iwlegacy: 3945: fix hw passive scan on radar channelsStanislaw Gruszka
commit 68acc4afb040d98ddfd2cae0de09e2f4e1ee127f upstream. Patch fix firmware error on "iw dev wlan0 scan passive" for hardware scanning (with disable_hw_scan=0 module parameter). iwl3945 0000:03:00.0: Microcode SW error detected. Restarting 0x82000008. iwl3945 0000:03:00.0: Loaded firmware version: 15.32.2.9 iwl3945 0000:03:00.0: Start IWL Error Log Dump: iwl3945 0000:03:00.0: Status: 0x0002A2E4, count: 1 iwl3945 0000:03:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line iwl3945 0000:03:00.0: SYSASSERT (0x5) 0041263900 0x13756 0x0031C 0x00000 764 iwl3945 0000:03:00.0: Error Reply type 0x000002FC cmd C_SCAN (0x80) seq 0x443E ser 0x00340000 iwl3945 0000:03:00.0: Command C_SCAN failed: FW Error iwl3945 0000:03:00.0: Can't stop Rx DMA. We have disable ability to change passive scanning to active on particular channel when traffic is detected on that channel. Otherwise firmware will report error, when we try to do passive scan on radar channels. Reported-and-debugged-by: Pedro Francisco <pedrogfrancisco@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-14 14:20:11 +0000