| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit d944b46992f8e99b6bdc721e44b02e5ca294fa2b ]
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f5d4c21a50716f8bd4e220544b82dca7408d113 ]
Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 848bd3f3de9d44950c00eda6c115e8e9785440da ]
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5b277402deac0691226a947df71c581686bd4020 ]
Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8f676b8508c250bbe255096522fdefb73f1ea0b9 ]
Whenever we update ns_head info, we need to make sure it is still
compatible with all underlying backing devices because although nvme
multipath doesn't have any explicit use of these limits, other devices
can still be stacked on top of it which may rely on the underlying limits.
Start with unlimited stacking limits, and every info update iterate over
siblings and adjust queue limits.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6778be4e520959659b27a441c06a84c9cb009085 ]
of_dma_configure() was *supposed* to be following the same logic as
acpi_dma_configure() and only setting bus_dma_mask if some range was
specified by the firmware. However, it seems that subtlety got lost in
the process of fitting it into the differently-shaped control flow, and
as a result the force_dma==true case ends up always setting the bus mask
to the 32-bit default, which is not what anyone wants.
Make sure we only touch it if the DT actually said so.
Fixes: 6c2fb2ea7636 ("of/device: Set bus DMA mask as appropriate")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Robert Richter <robert.richter@cavium.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63237f8748bdf46dccf79ef8f98f05e9fe799162 ]
[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:
[ 160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[ 160.697234] PGD 0 P4D 0
[ 160.697814] Oops: 0010 [#1] SMP PTI
[ 160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G O 4.19.0Lyude-Test+ #2
[ 160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[ 160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ 160.700322] RIP: 0010: (null)
[ 160.700920] Code: Bad RIP value.
[ 160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[ 160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[ 160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[ 160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[ 160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[ 160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[ 160.705260] FS: 0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[ 160.705854] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[ 160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 160.708372] Call Trace:
[ 160.708998] ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[ 160.709625] ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[ 160.710284] ? wake_up_q+0x54/0x70
[ 160.710877] ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[ 160.711512] ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[ 160.712161] ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[ 160.712762] ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[ 160.713408] ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[ 160.714013] ? process_one_work+0x1a1/0x3a0
[ 160.714667] ? worker_thread+0x30/0x380
[ 160.715326] ? wq_update_unbound_numa+0x10/0x10
[ 160.715939] ? kthread+0x112/0x130
[ 160.716591] ? kthread_create_worker_on_cpu+0x70/0x70
[ 160.717262] ? ret_from_fork+0x35/0x40
[ 160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[ 160.720141] CR2: 0000000000000000
Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.
[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0e6613e46fed29316f33acf86e1d1568288638b5 ]
[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.
[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02680efbb10be0d2c867fe722ae23d588f6bebef ]
[Why]
drm_plane_cleanup does not free the plane.
[How]
Call drm_primary_helper_destroy which will also free the plane.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f98e8a572bddbf27032114127d2fcc78fa5e6a9d ]
When the fixed factor clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Reported-by: Alan Tull <atull@kernel.org>
Fixes: 971451b3b15d ("clk: fixed-factor: Convert into a module platform driver")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d9cccfa7c4d1d9ef967ec9308df7304a18609b30 ]
If a call to xenmem_reservation_increase() in gnttab_dma_free_pages()
fails it triggers a message "Failed to decrease reservation..." which
should be "Failed to increase reservation..."
Fixes: 9bdc7304f536 ('xen/grant-table: Allow allocating buffers suitable for DMA')
Reported-by: Ross Philipson <ross.philipson@oracle.com>
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6ca469e22a30992b4478d2ab88737c70667c1e00 ]
This reverts commit 0586feba322e1de05075700eb4b835c8b683e62b
This patch makes it to need get_vblank_counter callback in crtc
to get frame counter from decon driver.
However, drm_dev->max_vblank_count is a member unique to
vendor's DRM driver but in case of ARM DRM, some CRTC devices
don't provide the frame counter value. As a result, this patch
made extension and clone mode not working.
Instead of this patch, we may need separated max_vblank_count
which belongs to each CRTC device, or need to implement frame
counter emulation for them who don't support HW frame counter.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3e61f01d755188cb6c2dcf5a244b9c0937c258e ]
If gcc decides not to inline make_sensor_label():
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e8ccbb7d2f53c62e14b889faaa3f6f809b657278 ]
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4b9 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30356d08159d7899438e94503ae322a8b881e205 ]
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e89f ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd74a7f9cc033cf4d405788f80292268987dc0c5 ]
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7dd8db68949a7acc5bd528ee0ecb8f8720f49921 ]
If userspace only reads the trackstick node, and no one is listening to
the touchpad nor the hidraw node then, the device is not powered on.
Add open/close callbacks to allow users to disable the touchpad in Gnome
while keeping the trackstick active.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1559632
Link: https://gitlab.gnome.org/GNOME/mutter/issues/128
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6298944d8f57f40ee2a3e6dcea1253e78d7a9969 ]
This reverts commit 67ddbb3e6568fb1820b2cc45b00c50702b114801.
67ddbb3e656 ("HID: add NOGET quirk for Eaton Ellipse MAX UPS") was reported
by Laurent Bigonville. It turns out that a later model Laurent got
doesn't need the quirk after all.
My take is that Eaton upgraded their firmwares, so we don't need it
anymore.
The old model was from 2012, so better make sure the new line works
properly by removing the quirk. This allows upower to actually fetch
the current data.
Reported-by: Laurent Bigonville <bigon@bigon.be>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00b790ea545b6ef30221adef6e9c3707e03b82b5 ]
Raydium touchpanel (2386:4B33) sometimes does not work in desktop session
although it works in display manager.
During user logging, the display manager exits, close the HID device,
then the device gets runtime suspended and powered off. The desktop
session begins shortly after, opens the HID device, then the device gets
runtime resumed and powered on.
If the trasition from display manager to desktop sesesion is fast, the
touchpanel cannot switch from powered off to powered on in short
timeframe. So add a small delay to workaround the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 202dc3cc10b4d37e5251431acf8d5040a8876c7d ]
On SCIFA and SCIFB serial ports with DMA support (i.e. some ports on
R-Car Gen2 and RZ/G1 SoCs), receive DMA operations are submitted before
the DMA channel pointer is initialized. Hence this fails, and the
driver tries to fall back to PIO. However, at this early phase in the
initialization sequence, fallback to PIO does not work, leading to a
serial port that cannot receive any data.
Fix this by calling sci_submit_rx() after initialization of the DMA
channel pointer.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2c4ee23530ffc022 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00a461cc32ec27fa7bd9c874a7b36b0c6c542c12 ]
Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.
Also fix the related node-reference leaks.
Fixes: 5b385a45e001 ("clk: ti: add support for clkctrl aliases")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ee02950d53eee0d4c7f1c08a35272b77d24b9459 ]
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526eba2143 ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2303a9ca693e585a558497ad737728fec97e2b8a ]
CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).
The other plls should not require this flag.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 69b93104c7ec5668019caf5d2dbfd0e182df06db ]
We found the PCIe driver doesn't really work with
the mpll3 clock which is actually reserved for debug,
So drop it from the mux list.
Fixes: 33b89db68236 ("clk: meson-axg: add clocks required by pcie driver")
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 684238d79ad85c5e19a71bb5818e77e329912fbc ]
To fix:
acerhdf: unknown (unsupported) BIOS version Gateway /LT31 /v1.3307 , please report, aborting!
As can be seen in the context, the BIOS registers haven't changed in
the previous versions, so the assumption is they won't have changed
in this last update for this somewhat older platform either.
Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b33228029d842269e17bba591609e83ed422005d ]
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 52091c256bdcad0d01e2852a63f19cd2cce6af96 ]
When the fixed rate clock is created by devicetree,
of_clk_add_provider is called. Add a call to
of_clk_del_provider in the remove function to balance
it out.
Signed-off-by: Alan Tull <atull@kernel.org>
Fixes: 435779fe1336 ("clk: fixed-rate: Convert into a module platform driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d98b1ef368feeb7720b8b9b6f3bd93f2ad892bc ]
On some Goldmont based systems such as ASRock J3455M the BIOS may not
enable the IPC1 device that provides access to the PMC and PUNIT. In
such scenarios, the IOSS and PSS resources from the platform device can
not be obtained and result in a invalid telemetry_plt_config which is an
internal data structure that holds platform config and is maintained by
the telemetry platform driver.
This is also applicable to the platforms where the BIOS supports IPC1
device under debug configurations but IPC1 is disabled by user or the
policy.
This change allows user to know the reason for not seeing entries under
/sys/kernel/debug/telemetry/* when there is no apparent failure at boot.
Cc: Matt Turner <matt.turner@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198779
Acked-by: Matt Turner <matt.turner@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 922dceff8dc1fb4dafc9af78139ba65671408103 ]
BOE panel (ID: 0x0771) that reports "DFP 1.x compliant TMDS".
But it's 6bpc panel only instead of 8 bpc.
Add panel ID to edid quirk list and set 6 bpc as default to
work around this issue.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540792173-7288-1-git-send-email-shawn.c.lee@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6702185c1ffec3421181b5e24491e3fac920cb61 ]
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b2f74dbaf12bf59ff35d451005b3cdee78232ff0 ]
The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.
Fixes: 3efb960f056d ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3c88ed1d798da355859ca083d3884a16ce0841f2 ]
In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.
The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a963052e539887df481d4d3a6ad4c92ca6461852 ]
Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().
Fixes: 6d4fab39533f ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 29118ab962d5476fdc65fae312ac38db68092d78 ]
Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().
Fixes: 6988eb2a9b77 ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 153fcd5f6d93b8e1e4040b1337f564a10f8d93af ]
brd_free() may be called in failure path on one brd instance which
disk isn't added yet, so release handler of gendisk may free the
associated request_queue early and causes the following use-after-free[1].
This patch fixes this issue by associating gendisk with request_queue
just before adding disk.
[1] KASAN: use-after-free Read in del_timer_syncNon-volatile memory driver v1.3
Linux agpgart interface v0.103
[drm] Initialized vgem 1.0.0 20120112 for virtual device on minor 0
usbcore: registered new interface driver udl
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20
kernel/locking/lockdep.c:3218
Read of size 8 at addr ffff8801d1b6b540 by task swapper/0/1
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.0+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.8+0x242/0x309 mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
__lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218
lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844
del_timer_sync+0xb7/0x270 kernel/time/timer.c:1283
blk_cleanup_queue+0x413/0x710 block/blk-core.c:809
brd_free+0x5d/0x71 drivers/block/brd.c:422
brd_init+0x2eb/0x393 drivers/block/brd.c:518
do_one_initcall+0x145/0x957 init/main.c:890
do_initcall_level init/main.c:958 [inline]
do_initcalls init/main.c:966 [inline]
do_basic_setup init/main.c:984 [inline]
kernel_init_freeable+0x5c6/0x6b9 init/main.c:1148
kernel_init+0x11/0x1ae init/main.c:1068
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:350
Reported-by: syzbot+3701447012fe951dabb2@syzkaller.appspotmail.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit f6e35cda66146106cfeb85ed65696e0f8e793fee upstream.
Use I915_GTT_PAGE_SIZE when talking about GTT pages rather than
physical pages.
There are some PAGE_SHIFTs left though. Not sure if we want to
introduce I915_GTT_PAGE_SHIFT or what?
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk> # at least some of it :)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180913150405.706-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7b900ead6cc66b2ee873cb042dfba169aa68b56c ]
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 85b18b0237ce9986a81a1b9534b5e2ee116f5504 ]
The commit f77f0aee4da4 ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4da4 ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 96801552f846460fe9ac10f1b189602992f004e1 ]
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73ce ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df5a8ec64eed7fe45b556cfff503acd6429ab817 ]
Up until commit 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e0700 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 284fb78ed7572117846f8e1d1d8e3dbfd16880c2 ]
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50ab90e5 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d02854dc1999ed3e7fd79ec700c64ac23ac0c458 ]
A null dereference was observed when a sysctl was being set
from userspace and rmnet was stuck trying to complete some actions
in the NETDEV_REGISTER callback. This is because the real_dev is set
only after the device registration handler completes.
sysctl call stack -
<6> Unable to handle kernel NULL pointer dereference at
virtual address 00000108
<2> pc : rmnet_vnd_get_iflink+0x1c/0x28
<2> lr : dev_get_iflink+0x2c/0x40
<2> rmnet_vnd_get_iflink+0x1c/0x28
<2> inet6_fill_ifinfo+0x15c/0x234
<2> inet6_ifinfo_notify+0x68/0xd4
<2> ndisc_ifinfo_sysctl_change+0x1b8/0x234
<2> proc_sys_call_handler+0xac/0x100
<2> proc_sys_write+0x3c/0x4c
<2> __vfs_write+0x54/0x14c
<2> vfs_write+0xcc/0x188
<2> SyS_write+0x60/0xc0
<2> el0_svc_naked+0x34/0x38
device register call stack -
<2> notifier_call_chain+0x84/0xbc
<2> raw_notifier_call_chain+0x38/0x48
<2> call_netdevice_notifiers_info+0x40/0x70
<2> call_netdevice_notifiers+0x38/0x60
<2> register_netdevice+0x29c/0x3d8
<2> rmnet_vnd_newlink+0x68/0xe8
<2> rmnet_newlink+0xa0/0x160
<2> rtnl_newlink+0x57c/0x6c8
<2> rtnetlink_rcv_msg+0x1dc/0x328
<2> netlink_rcv_skb+0xac/0x118
<2> rtnetlink_rcv+0x24/0x30
<2> netlink_unicast+0x158/0x1f0
<2> netlink_sendmsg+0x32c/0x338
<2> sock_sendmsg+0x44/0x60
<2> SyS_sendto+0x150/0x1ac
<2> el0_svc_naked+0x34/0x38
Fixes: b752eff5be24 ("net: qualcomm: rmnet: Implement ndo_get_iflink")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0432e833191ad4d17b7fc2364941f91dad51db1a ]
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44b ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a9049ff9214da68df1179a7d5e36b43479abc9b8 ]
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acf3766b36d8e59ecbc307894c6d05703ee48014 ]
The mlx5e channels should be closed before mlx5i_uninit_underlay_qp
puts the QP into RST (reset) state during mlx5i_close. Currently QP
state incorrectly set to RST before channels got deactivated and closed,
since mlx5_post_send request expects QP in RTS (Ready To Send) state.
The fix is to keep QP in RTS state until mlx5e channels get closed
and to reset QP afterwards.
Also this fix is simply correct in order to keep the open/close flow
symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open,
the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing
at close, which is exactly what this patch is doing.
Fixes: dae37456c8ac ("net/mlx5: Support for attaching multiple underlay QPs to root flow table")
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f2b18732ee9863ac036759baf616ffa03c252ed5 ]
The commit "net/mlx5: Refactor accel IPSec code" introduced a
bug where asynchronous short time change in hash key value
by create/release SA context might happen during an asynchronous
hash resize operation this could cause a subsequent remove SA
context operation to fail as the key value used during resize is
not the same key value used when remove SA context operation is
invoked.
This commit fixes the bug by defining the SA context hash key
such that it includes only fields that never change during the
lifetime of the SA context object.
Fixes: d6c4f0298cec ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 64e283348458e2fd2fe41b60dfb6c30e88ee695f ]
Querying interface FEC caps with 'ethtool [int]' after link reset
throws warning regading link speed.
This warning is not needed as there is already an indication in
user space that the link is not up.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 228c4cd04dfd0667eda182c91504b83c17d97584 ]
Loopback test had fixed packet size, which can be bigger than configured
MTU. Shorten the loopback packet size to be bigger than minimal MTU
allowed by the device. Text field removed from struct 'mlx5ehdr'
as redundant to allow send small packets as minimal allowed MTU.
Fixes: d605d66 ("net/mlx5e: Add support for ethtool self diagnostics test")
Signed-off-by: Valentine Fatiev <valentinef@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 83621b7df6a646e550fd3d36db2e301cf9a5096b ]
We get the match level (none, l2, l3, l4) while going over the match
dissectors of an offloaded tc rule. When doing this, the match level
enum and the not min inline enum values should be used, fix that.
This worked accidentally b/c both enums have the same numerical values.
Fixes: d708f902989b ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0073c8f72736b423aade8a817587a5f3e4df4ad8 ]
In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means
that WQE (RX descriptor) can be used for many packets and so the WQE is
much bigger than MTU. In virtualization setups where the port mtu can
be larger than the vf mtu, if received packet is bigger than MTU, it
won't be dropped by HW on too small receive WQE. If we use linear SKB in
striding RQ, since each stride has room for mtu size payload and skb
info, an oversized packet can lead to crash for crossing allocated page
boundary upon the call to build_skb. So driver needs to check packet
size and drop it.
Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the
number of packets dropped by the driver for being too large.
As a new field is added to the RQ struct, re-open the channels whenever
this field is being used in datapath (i.e., in the case of linear
Striding RQ).
Fixes: 619a8f2a42f1 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
