| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit d6c9b31ac3064fbedf8961f120a4c117daa59932 ]
These are called with IRQs disabled from csio_mgmt_tmo_handler() so we
can't call spin_unlock_irq() or it will enable IRQs prematurely.
Fixes: a3667aaed569 ("[SCSI] csiostor: Chelsio FCoE offload driver")
Link: https://lore.kernel.org/r/20191019085913.GA14245@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit feff8b3d84d3d9570f893b4d83e5eab6693d6a52 ]
When operating in private loop mode, PLOGI exchanges are racing and the
driver tries to abort it's PLOGI. But the PLOGI abort ends up terminating
the login with the other end causing the other end to abort its PLOGI as
well. Discovery never fully completes.
Fix by disabling the PLOGI abort when private loop and letting the state
machine play out.
Link: https://lore.kernel.org/r/20191018211832.7917-5-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cef2a7955f2754257a7cddedec16edae7b587d0 ]
RFC 2307 states:
For CHAP [RFC1994], in the first step, the initiator MUST send:
CHAP_A=<A1,A2...>
Where A1,A2... are proposed algorithms, in order of preference.
...
For the Algorithm, as stated in [RFC1994], one value is required to
be implemented:
5 (CHAP with MD5)
LIO currently checks for this value by only comparing a single byte in
the tokenized Algorithm string, which means that any value starting with
a '5' (e.g. "55") is interpreted as "CHAP with MD5". Fix this by
comparing the entire tokenized string.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Link: https://lore.kernel.org/r/20190912095547.22427-2-ddiss@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96d3ab802e4930a29a33934373157d6dff1b2c7e ]
Page tables that reside in physical memory beyond the 4 GiB boundary are
currently not working properly. The reason is that when the physical
address for page directory entries is read, it gets truncated at 32 bits
and can cause crashes when passing that address to the DMA API.
Fix this by first casting the PDE value to a dma_addr_t and then using
the page frame number mask for the SMMU instance to mask out the invalid
bits, which are typically used for mapping attributes, etc.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 463fa44eec2fef50d111ed0199cf593235065c04 ]
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 07b8582430370097238b589f4e24da7613ca6dd3 ]
Symptoms were seen of the driver not having valid data for mailbox
commands. After debugging, the following sequence was found:
The driver maintains a port-wide pointer of the mailbox command that is
currently in execution. Once finished, the port-wide pointer is cleared
(done in lpfc_sli4_mq_release()). The next mailbox command issued will set
the next pointer and so on.
The mailbox response data is only copied if there is a valid port-wide
pointer.
In the failing case, it was seen that a new mailbox command was being
attempted in parallel with the completion. The parallel path was seeing
the mailbox no long in use (flag check under lock) and thus set the port
pointer. The completion path had cleared the active flag under lock, but
had not touched the port pointer. The port pointer is cleared after the
lock is released. In this case, the completion path cleared the just-set
value by the parallel path.
Fix by making the calls that clear mbox state/port pointer while under
lock. Also slightly cleaned up the error path.
Link: https://lore.kernel.org/r/20190922035906.10977-8-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 782b281883caf70289ba6a186af29441a117d23e ]
When user issues diag register command from application with required size,
and if driver unable to allocate the memory, then it will fail the register
command. While failing the register command, driver is not currently
clearing MPT3_CMD_PENDING bit in ctl_cmds.status variable which was set
before trying to allocate the memory. As this bit is set, subsequent
register command will be failed with BUSY status even when user wants to
register the trace buffer will less memory.
Clear MPT3_CMD_PENDING bit in ctl_cmds.status before returning the diag
register command with no memory status.
Link: https://lore.kernel.org/r/1568379890-18347-4-git-send-email-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fe0acab448f68c3146235afe03fb932e242ec94c upstream.
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66fa ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e42712596 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab42b48f32d4c766420c3499ee9c0289b7028182 upstream.
The "auto-attach" handler function `gsc_hpdi_auto_attach()` calls
`dma_alloc_coherent()` in a loop to allocate some DMA data buffers, and
also calls it to allocate a buffer for a DMA descriptor chain. However,
it does not check the return value of any of these calls. Change
`gsc_hpdi_auto_attach()` to return `-ENOMEM` if any of these
`dma_alloc_coherent()` calls fail. This will result in the comedi core
calling the "detach" handler `gsc_hpdi_detach()` as part of the
clean-up, which will call `gsc_hpdi_free_dma()` to free any allocated
DMA coherent memory buffers.
Cc: <stable@vger.kernel.org> #4.6+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20191216110823.216237-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 133b2acee3871ae6bf123b8fe34be14464aa3d2c upstream.
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b4932 ("hp-wmi: limit hotkey enable")
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64cc3f12d1c7dd054a215bc1ff9cc2abcfe35832 upstream.
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
[1] [https://www.usb.org/document-library/usb-20-specification, usb_20.pdf]
[2] [https://www.intel.com/content/dam/www/public/us/en/documents/
technical-specifications/ehci-specification-for-usb.pdf]
Signed-off-by: Erkka Talvitie <erkka.talvitie@vincit.fi>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ef70941d5f349767f19c0ed26b0dd9eed8ad81bb.1576050523.git.erkka.talvitie@vincit.fi
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aabb5b833872524eaf28f52187e5987984982264 upstream.
If a transaction error happens in vhci_recv_ret_submit(), event
handler closes connection and changes port status to kick hub_event.
Then hub tries to flush the endpoint URBs, but that causes infinite
loop between usb_hub_flush_endpoint() and vhci_urb_dequeue() because
"vhci_priv" in vhci_urb_dequeue() was already released by
vhci_recv_ret_submit() before a transmission error occurred. Thus,
vhci_urb_dequeue() terminates early and usb_hub_flush_endpoint()
continuously calls vhci_urb_dequeue().
The root cause of this issue is that vhci_recv_ret_submit()
terminates early without giving back URB when transaction error
occurs in vhci_recv_ret_submit(). That causes the error URB to still
be linked at endpoint list without “vhci_priv".
So, in the case of transaction error in vhci_recv_ret_submit(),
unlink URB from the endpoint, insert proper error code in
urb->status and give back URB.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191213023055.19933-3-suwan.kim027@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 20032b63586ac6c28c936dff696981159913a13f ]
Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.
Fixes: ce85e13ad6ef ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cad46039e4c99812db067c8ac22a864960e7acc4 ]
ql_alloc_large_buffers() has the usual RX buffer allocation
loop where it allocates skbs and maps them for DMA. It also
treats failure as a fatal error.
There are (at least) three bugs in the error paths:
1. ql_free_large_buffers() assumes that the lrg_buf[] entry for the
first buffer that couldn't be allocated will have .skb == NULL.
But the qla_buf[] array is not zero-initialised.
2. ql_free_large_buffers() DMA-unmaps all skbs in lrg_buf[]. This is
incorrect for the last allocated skb, if DMA mapping failed.
3. Commit 1acb8f2a7a9f ("net: qlogic: Fix memory leak in
ql_alloc_large_buffers") added a direct call to dev_kfree_skb_any()
after the skb is recorded in lrg_buf[], so ql_free_large_buffers()
will double-free it.
The bugs are somewhat inter-twined, so fix them all at once:
* Clear each entry in qla_buf[] before attempting to allocate
an skb for it. This goes half-way to fixing bug 1.
* Set the .skb field only after the skb is DMA-mapped. This
fixes the rest.
Fixes: 1357bfcf7106 ("qla3xxx: Dynamically size the rx buffer queue ...")
Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() ...")
Fixes: 1acb8f2a7a9f ("net: qlogic: Fix memory leak in ql_alloc_large_buffers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90b3b339364c76baa2436445401ea9ade040c216 ]
When doing stress test, we get the following trace:
kernel BUG at lib/dynamic_queue_limits.c:26!
Internal error: Oops - BUG: 0 [#1] SMP ARM
Modules linked in: hip04_eth
CPU: 0 PID: 2003 Comm: tDblStackPcap0 Tainted: G O L 4.4.197 #1
Hardware name: Hisilicon A15
task: c3637668 task.stack: de3bc000
PC is at dql_completed+0x18/0x154
LR is at hip04_tx_reclaim+0x110/0x174 [hip04_eth]
pc : [<c041abfc>] lr : [<bf0003a8>] psr: 800f0313
sp : de3bdc2c ip : 00000000 fp : c020fb10
r10: 00000000 r9 : c39b4224 r8 : 00000001
r7 : 00000046 r6 : c39b4000 r5 : 0078f392 r4 : 0078f392
r3 : 00000047 r2 : 00000000 r1 : 00000046 r0 : df5d5c80
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 32c5387d Table: 1e189b80 DAC: 55555555
Process tDblStackPcap0 (pid: 2003, stack limit = 0xde3bc190)
Stack: (0xde3bdc2c to 0xde3be000)
[<c041abfc>] (dql_completed) from [<bf0003a8>] (hip04_tx_reclaim+0x110/0x174 [hip04_eth])
[<bf0003a8>] (hip04_tx_reclaim [hip04_eth]) from [<bf0012c0>] (hip04_rx_poll+0x20/0x388 [hip04_eth])
[<bf0012c0>] (hip04_rx_poll [hip04_eth]) from [<c04c8d9c>] (net_rx_action+0x120/0x374)
[<c04c8d9c>] (net_rx_action) from [<c021eaf4>] (__do_softirq+0x218/0x318)
[<c021eaf4>] (__do_softirq) from [<c021eea0>] (irq_exit+0x88/0xac)
[<c021eea0>] (irq_exit) from [<c0240130>] (msa_irq_exit+0x11c/0x1d4)
[<c0240130>] (msa_irq_exit) from [<c0267ba8>] (__handle_domain_irq+0x110/0x148)
[<c0267ba8>] (__handle_domain_irq) from [<c0201588>] (gic_handle_irq+0xd4/0x118)
[<c0201588>] (gic_handle_irq) from [<c0558360>] (__irq_svc+0x40/0x58)
Exception stack(0xde3bdde0 to 0xde3bde28)
dde0: 00000000 00008001 c3637668 00000000 00000000 a00f0213 dd3627a0 c0af6380
de00: c086d380 a00f0213 c0a22a50 de3bde6c 00000002 de3bde30 c0558138 c055813c
de20: 600f0213 ffffffff
[<c0558360>] (__irq_svc) from [<c055813c>] (_raw_spin_unlock_irqrestore+0x44/0x54)
Kernel panic - not syncing: Fatal exception in interrupt
Pre-modification code:
int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
[...]
[1] priv->tx_head = TX_NEXT(tx_head);
[2] count++;
[3] netdev_sent_queue(ndev, skb->len);
[...]
}
An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2,
tx_head has been updated, but corresponding 'skb->len' has not been
added to dql_queue.
And then
hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim
In hip04_tx_reclaim, because tx_head has been updated,
bytes_compl will plus an additional "skb-> len"
which has not been added to dql_queue. And then
trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
To solve the problem described above, we put
"netdev_sent_queue(ndev, skb->len);"
before
"priv->tx_head = TX_NEXT(tx_head);"
Fixes: a41ea46a9a12 ("net: hisilicon: new hip04 ethernet driver")
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a288f105a03a7e0e629a8da2b31f34ebf0343ee2 ]
fjes_acpi_add() misses a check for platform_device_register_simple().
Add a check to fix it.
Fixes: 658d439b2292 ("fjes: Introduce FUJITSU Extended Socket Network Device driver")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6056a0f8ede27b296d10ef46f7f677cc9d715371 ]
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dca8 ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dca8
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 07bcc411567cb96f9d1fc84fff8d387118a2920d upstream.
This reverts commit c894e33ddc1910e14d6f2a2016f60ab613fd8b37.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a5d66f810061e2dd70fb7a108dcd14e535bc639f ]
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ee812f6143d78d8ba1399671d78c8d78bf2817c ]
In the vmx crypto Makefile we assign to a variable called TARGET and
pass that to the aesp8-ppc.pl and ghashp8-ppc.pl scripts.
The variable is meant to describe what flavour of powerpc we're
building for, eg. either 32 or 64-bit, and big or little endian.
Unfortunately TARGET is a fairly common name for a make variable, and
if it happens that TARGET is specified as a command line parameter to
make, the value specified on the command line will override our value.
In particular this can happen if the kernel Makefile is driven by an
external Makefile that uses TARGET for something.
This leads to weird build failures, eg:
nonsense at /build/linux/drivers/crypto/vmx/ghashp8-ppc.pl line 45.
/linux/drivers/crypto/vmx/Makefile:20: recipe for target 'drivers/crypto/vmx/ghashp8-ppc.S' failed
Which shows that we passed an empty value for $(TARGET) to the perl
script, confirmed with make V=1:
perl /linux/drivers/crypto/vmx/ghashp8-ppc.pl > drivers/crypto/vmx/ghashp8-ppc.S
We can avoid this confusion by using override, to tell make that we
don't want anything to override our variable, even a value specified
on the command line. We can also use a less common name, given the
script calls it "flavour", let's use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a7126603d46fe8f01aeedf589e071c6aaa6c6c39 ]
If you try to compile this driver on a 64-bit platform then you
will get warnings because it mixes size_t with unsigned int which
only works on 32-bit.
This patch fixes all of the warnings on sun4i-ss-hash.c.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 21f585480deb4bcf0d92b08879c35d066dfee030 ]
New GCC warns about inappropriate use of strncpy():
drivers/staging/fbtft/fbtft-core.c: In function ‘fbtft_framebuffer_alloc’:
drivers/staging/fbtft/fbtft-core.c:665:2: warning: ‘strncpy’ specified bound 16 equals destination size [-Wstringop-truncation]
665 | strncpy(info->fix.id, dev->driver->name, 16);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Later on the copy is being used with the assumption to be NULL terminated.
Make sure string is NULL terminated by switching to snprintf().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191120095716.26628-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5974fbb5e10b018fdbe3c3b81cb4cc54e1105ab9 ]
kasprintf() can fail, we should check the return value.
Fixes: 5ed540aecc2a ("iwlwifi: use mac80211 throughput trigger")
Fixes: 8ca151b568b6 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04358e40ba96d687c0811c21d9dede73f5244a98 ]
The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46770be0cf94149ca48be87719bda1d951066644 ]
The cpufreq core heavily depends on the availability of the struct
device for CPUs and if they aren't available at the time cpufreq driver
is registered, we will never succeed in making cpufreq work.
This happens due to following sequence of events:
- cpufreq_register_driver()
- subsys_interface_register()
- return 0; //successful registration of driver
... at a later point of time
- register_cpu();
- device_register();
- bus_probe_device();
- sif->add_dev();
- cpufreq_add_dev();
- get_cpu_device(); //FAILS
- per_cpu(cpu_sys_devices, num) = &cpu->dev; //used by get_cpu_device()
- return 0; //CPU registered successfully
Because the per-cpu variable cpu_sys_devices is set only after the CPU
device is regsitered, cpufreq will never be able to get it when
cpufreq_add_dev() is called.
This patch avoids this failure by making sure device structure of at
least CPU0 is available when the cpufreq driver is registered, else
return -EPROBE_DEFER.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 231ec2f24dad18d021b361045bbd618ba62a274e ]
Usually all the distro will load the parport low level driver as part
of their initialization. But we can get into a situation where all the
parallel port drivers are built as module and we unload all the modules
at a later time. Then if we just do "modprobe parport" it will only
load the parport module and will not load the low level driver which
will actually register the ports. So, check the bus if there is any
parport registered, if not, load the low level driver.
We can get into the above situation with all distro but only Suse has
setup the alias for "parport_lowlevel" and so it only works in Suse.
Users of Debian based distro will need to load the lowlevel module
manually.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20191016144540.18810-3-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5eb263ef08b5014cfc2539a838f39d2fd3531423 ]
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7088e29e0423d3195e09079b4f849ec4837e5a75 ]
The current code to convert a physical address mask to a grain
(defined as granularity in bytes) is:
e->grain = ~(mem_err->physical_addr_mask & ~PAGE_MASK);
This is broken in several ways:
1) It calculates to wrong grain values. E.g., a physical address mask
of ~0xfff should give a grain of 0x1000. Without considering
PAGE_MASK, there is an off-by-one. Things are worse when also
filtering it with ~PAGE_MASK. This will calculate to a grain with the
upper bits set. In the example it even calculates to ~0.
2) The grain does not depend on and is unrelated to the kernel's
page-size. The page-size only matters when unmapping memory in
memory_failure(). Smaller grains are wrongly rounded up to the
page-size, on architectures with a configurable page-size (e.g. arm64)
this could round up to the even bigger page-size of the hypervisor.
Fix this with:
e->grain = ~mem_err->physical_addr_mask + 1;
The grain_bits are defined as:
grain = 1 << grain_bits;
Change also the grain_bits calculation accordingly, it is the same
formula as in edac_mc.c now and the code can be unified.
The value in ->physical_addr_mask coming from firmware is assumed to
be contiguous, but this is not sanity-checked. However, in case the
mask is non-contiguous, a conversion to grain_bits effectively
converts the grain bit mask to a power of 2 by rounding it up.
Suggested-by: James Morse <james.morse@arm.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20191106093239.25517-11-rrichter@marvell.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2df200ab234a86836a8879a05a8007d6b884eb14 ]
The driver misses calling v4l2_ctrl_handler_free and
v4l2_device_unregister in remove like what is done in probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7f404ae9cf2a285f73b3c18ab9303d54b7a3d8e1 ]
In some device configurations there's no radio or radio support in the
driver. That's OK, as the driver sets itself up accordingly. However
on tear-down in these caes it's still trying to tear down radio
related context when there isn't anything there, leading to
dereferences through a null pointer and chaos follows.
How this bug survived unfixed for 11 years in the pvrusb2 driver is a
mystery to me.
[hverkuil: fix two checkpatch warnings]
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 05a11003a56507023f18d3249a4d4d119c0a3e9c ]
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5174f1e41074b5186608badc2e89441d021e8c08 ]
This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:
unreferenced object 0xec13ee40 (size 176):
comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
[<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
[<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
[<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
[<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
[<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
[<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
[<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
[<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
[<ac5fcae4>] process_one_work+0x22c/0x564
[<f5e6d3b6>] worker_thread+0x44/0x5d8
[<82c7b073>] kthread+0x150/0x154
[<b43e1b7d>] ret_from_fork+0x14/0x2c
[<794dff30>] 0x0
It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9a8ba9769a0e354341bc6cc01b98aadcea1dfe9 ]
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc5a3d79c345871439ffe72550b604fcde9770e1 ]
PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 884caadad128efad8e00c1cdc3177bc8912ee8ec ]
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 130f4caf145c3562108b245a576db30b916199d2 ]
With CONFIG_DEBUG_TEST_DRIVER_REMOVE set, we may find the following WARN:
[ 23.452574] ------------[ cut here ]------------
[ 23.457190] WARNING: CPU: 59 PID: 1 at drivers/ata/libata-core.c:6676 ata_host_detach+0x15c/0x168
[ 23.466047] Modules linked in:
[ 23.469092] CPU: 59 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00010-g5b83fd27752b-dirty #296
[ 23.477776] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 23.486286] pstate: a0c00009 (NzCv daif +PAN +UAO)
[ 23.491065] pc : ata_host_detach+0x15c/0x168
[ 23.495322] lr : ata_host_detach+0x88/0x168
[ 23.499491] sp : ffff800011cabb50
[ 23.502792] x29: ffff800011cabb50 x28: 0000000000000007
[ 23.508091] x27: ffff80001137f068 x26: ffff8000112c0c28
[ 23.513390] x25: 0000000000003848 x24: ffff0023ea185300
[ 23.518689] x23: 0000000000000001 x22: 00000000000014c0
[ 23.523987] x21: 0000000000013740 x20: ffff0023bdc20000
[ 23.529286] x19: 0000000000000000 x18: 0000000000000004
[ 23.534584] x17: 0000000000000001 x16: 00000000000000f0
[ 23.539883] x15: ffff0023eac13790 x14: ffff0023eb76c408
[ 23.545181] x13: 0000000000000000 x12: ffff0023eac13790
[ 23.550480] x11: ffff0023eb76c228 x10: 0000000000000000
[ 23.555779] x9 : ffff0023eac13798 x8 : 0000000040000000
[ 23.561077] x7 : 0000000000000002 x6 : 0000000000000001
[ 23.566376] x5 : 0000000000000002 x4 : 0000000000000000
[ 23.571674] x3 : ffff0023bf08a0bc x2 : 0000000000000000
[ 23.576972] x1 : 3099674201f72700 x0 : 0000000000400284
[ 23.582272] Call trace:
[ 23.584706] ata_host_detach+0x15c/0x168
[ 23.588616] ata_pci_remove_one+0x10/0x18
[ 23.592615] ahci_remove_one+0x20/0x40
[ 23.596356] pci_device_remove+0x3c/0xe0
[ 23.600267] really_probe+0xdc/0x3e0
[ 23.603830] driver_probe_device+0x58/0x100
[ 23.608000] device_driver_attach+0x6c/0x90
[ 23.612169] __driver_attach+0x84/0xc8
[ 23.615908] bus_for_each_dev+0x74/0xc8
[ 23.619730] driver_attach+0x20/0x28
[ 23.623292] bus_add_driver+0x148/0x1f0
[ 23.627115] driver_register+0x60/0x110
[ 23.630938] __pci_register_driver+0x40/0x48
[ 23.635199] ahci_pci_driver_init+0x20/0x28
[ 23.639372] do_one_initcall+0x5c/0x1b0
[ 23.643199] kernel_init_freeable+0x1a4/0x24c
[ 23.647546] kernel_init+0x10/0x108
[ 23.651023] ret_from_fork+0x10/0x18
[ 23.654590] ---[ end trace 634a14b675b71c13 ]---
With KASAN also enabled, we may also get many use-after-free reports.
The issue is that when CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, we may
attempt to detach the ata_port before it has been probed.
This is because the ata_ports are async probed, meaning that there is no
guarantee that the ata_port has probed prior to detach. When the ata_port
does probe in this scenario, we get all sorts of issues as the detach may
have already happened.
Fix by ensuring synchronisation with async_synchronize_full(). We could
alternatively use the cookie returned from the ata_port probe
async_schedule() call, but that means managing the cookie, so more
complicated.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec3b7b6eb8c90b52f61adff11b6db7a8db34de19 ]
"clock" may be copied to "best_clock". Initializing best_clock
is not sufficient. The fix initializes clock as well to avoid
memory disclosures and informaiton leaks.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191018044150.1899-1-kjlu@umn.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db033831b4f5589f9fcbadb837614a7c4eac0308 ]
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6942635032cfd3e003e980d2dfa4e6323a3ce145 ]
On some devices (e.g. Samsung Galaxy A5 (2015)), the bootloader
seems to keep interrupts enabled for SM5502 when booting Linux.
Changing the cable state (i.e. plugging in a cable) - until the driver
is loaded - will therefore produce an interrupt that is never read.
In this situation, the cable state will be stuck forever on the
initial state because SM5502 stops sending interrupts.
This can be avoided by clearing those pending interrupts after
the driver has been loaded.
One way to do this is to reset all registers to default state
by writing to SM5502_REG_RESET. This ensures that we start from
a clean state, with all interrupts disabled.
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e20b248051ca0f90d84b4d9378e4780bc31f16c6 ]
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2444846c0dbfa4ead21b621e4300ec32c90fbf38 ]
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06bec72b250b2cb3ba96fa45c2b8e0fb83745517 ]
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d10dcb615c8e29d403a24d35f8310a7a53e3050c ]
In mwifiex_pcie_init_evt_ring, a new skb is allocated which should be
released if mwifiex_map_pci_memory() fails. The release for skb and
card->evtbd_ring_vbase is added.
Fixes: 0732484b47b5 ("mwifiex: separate ring initialization and ring creation routines")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 649cd16c438f51d4cd777e71ca1f47f6e0c5e65d ]
If usb_set_interface() failed, iface->cur_altsetting will
not be assigned and it will be used in flexcop_usb_transfer_init()
It may lead a NULL pointer dereference.
Check usb_set_interface() return value in flexcop_usb_init()
and return failed to avoid using this NULL pointer.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
max8907_regulator_probe()
[ Upstream commit 472b39c3d1bba0616eb0e9a8fa3ad0f56927c7d7 ]
Inside function max8907_regulator_probe(), variable val could
be uninitialized if regmap_read() fails. However, val is used
later in the if statement to decide the content written to
"pmic", which is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20191003175813.16415-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eaecce12f5f0d2c35d278e41e1bc4522393861ab ]
When unloading omap3-rom-rng, we'll get the following:
WARNING: CPU: 0 PID: 100 at drivers/clk/clk.c:948 clk_core_disable
This is because the clock may be already disabled by omap3_rom_rng_idle().
Let's fix the issue by checking for rng_idle on exit.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes: 1c6b7c2108bd ("hwrng: OMAP3 ROM Random Number Generator support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 39abcc84846bbc0538f13c190b6a9c7e36890cd2 ]
When R-Car Gen3 USB 2.0 is in Gadget mode, if host is detached an interrupt
will be generated and Suspended state bit is set in interrupt status
register. Interrupt handler will call driver->suspend(composite_suspend)
if suspended state bit is set. composite_suspend will call
ffs_func_suspend which will post FUNCTIONFS_SUSPEND and will be consumed
by user space application via /dev/ep0.
To be able to detect host detach, extend the DVSQ_MASK to cover the
Suspended bit of the DVSQ[2:0] bitfield from the Interrupt Status
Register 0 (INTSTS0) register and perform appropriate action in the
DVST interrupt handler (usbhsg_irq_dev_state).
Without this commit, disconnection of the phone from R-Car-H3 ES2.0
Salvator-X CN9 port is not recognized and reverse role switch does
not happen. If phone is connected again it does not enumerate.
With this commit, disconnection will be recognized and reverse role
switch will happen by a user space application. If phone is connected
again it will enumerate properly and will become visible in the output
of 'lsusb'.
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1568207756-22325-3-git-send-email-external.veeraiyan.c@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3143b459de4cdcce67b36827476c966e93c1cf01 ]
The driver stores frame format settings supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, those settings are updated before they are actually applied
on hardware. If an error occurs on device update, the stored settings
my not reflect hardware state anymore and consecutive calls to
.get_fmt() may return incorrect information. That in turn may affect
ability of a bridge device to use correct DMA transfer settings if such
incorrect informmation on active frame format returned by .get_fmt() is
used.
Assuming a failed device update means its state hasn't changed, update
frame format related settings stored in the device private structure
only after they are successfully applied so the stored values always
reflect hardware state as closely as possible.
Fixes: 2f6e2404799a ("[media] SoC Camera: add driver for OV6650 sensor")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9d669fbfca20e6035ead814e55d9ef1a6b500540 ]
The initial registers sequence is only loaded at probe
time. Afterward only the resolution and format specific
register are modified. Care must be taken to make sure
registers modified by one resolution setting are reverted
back when another resolution is programmed.
This was not done properly for the 720p case.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85c4043f1d403c222d481dfc91846227d66663fb ]
In ov2659_s_stream() return value for invoked function should be checked
and propagated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
