Age | Commit message (Collapse) | Author |
|
|
|
SSYNC register was once defined as 0x34-37 in the old Intel datasheet,
but corrected later to 0x38-3b. For fixing the register usage, a new
bit-flag is introduced for indicating the old ICH SSYNC register, and
ICH* PCI entries are added explicitly to enable this quirk.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some HP laptops with AD1981 have SPDIF connections, but currently the
driver disables it statically. Better to check the pin default config
to judge whether to enable or disable the SPDIF.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
If DMA active status should be checked, I2SCON register should be referenced.
In this patch, Fix the incorrect referencing of I2SCON register.
Reported-by : Lakkyung Jung <lakkyung.jung@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
Make sure we follow naming convention for all PCM ops.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
In preparation for the new ASoC Dynamic PCM support (AKA DSP support).
The new ASoC Dynamic PCM core allows DAIs to be dynamically re-routed
at runtime between the PCM device end (or Frontend - FE) and the physical DAI
(Backend - BE) using regular kcontrols (just like a hardware CODEC routes
audio in the analog domain). The Dynamic PCM core therefore must be
able to call PCM operations for both the Frontend and Backend(s) DAIs at
the same time.
Currently we have a global pcm_mutex that is used to serialise
the ASoC PCM operations. This patch removes the global mutex
and adds a mutex per RTD allowing the PCM operations to be reentrant and
allow control of more than one DAI at at time. e.g. a frontend PCM hw_params()
could configure multiple backend DAI hw_params() with similar or different
hw parameters at the same time.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
In preparation for Dynamic PCM support (AKA DSP support).
There will be future patches that add support to allow PCMs to be dynamically
routed to multiple DAIs at startup and also during stream runtime. This patch
moves the ASoC core PCM operaitions into a new file called soc-pcm.c. This will
in simplify the ASoC core features into distinct files.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Currently it is possible that snd_soc_new_{mixer,mux,pga} is called with a
DAPM context not matching the widgets context. This can lead to a wrong
prefix_len calculation, which will result in undefined behaviour. To avoid
this always use the DAPM context from the widget itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: alsa-devel@alsa-project.org
Link: http://lkml.kernel.org/r/20110601180610.532642190@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180610.054254048@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/arm/mach-footbridge/isa-timer.c | 2 +-
arch/mips/cobalt/time.c | 2 +-
arch/mips/jazz/irq.c | 2 +-
arch/mips/kernel/i8253.c | 2 +-
arch/mips/mti-malta/malta-time.c | 2 +-
arch/mips/sgi-ip22/ip22-time.c | 2 +-
arch/mips/sni/time.c | 2 +-
arch/x86/kernel/apic/apic.c | 2 +-
arch/x86/kernel/apm_32.c | 2 +-
arch/x86/kernel/hpet.c | 2 +-
arch/x86/kernel/i8253.c | 2 +-
arch/x86/kernel/time.c | 2 +-
drivers/block/hd.c | 2 +-
drivers/clocksource/i8253.c | 2 +-
drivers/input/gameport/gameport.c | 2 +-
drivers/input/joystick/analog.c | 2 +-
drivers/input/misc/pcspkr.c | 2 +-
include/linux/i8253.h | 11 +++++++++++
sound/drivers/pcsp/pcsp.h | 2 +-
19 files changed, 29 insertions(+), 18 deletions(-)
|
|
|
|
Device tree integer properties are encoded in big-endian format, but some of
the Freescale ASoC drivers were assuming that the host is in big-endian format
as well. Although this is true, it's better to use endian-safe accessors.
Also add a check for a failed ioremap() call in the SSI driver.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The DMA (PCM) driver used by some Freescale PowerPC supports separate DAIs
for playback and capture, so DMA buffers should be allocated only for the
initialized streams. Instead of checking for the number of active channels,
which apparently is not reliable, check to see if the actual stream object
exists.
Also provide a better name for the DMA interrupt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Reported-by: Kieran O'Leary <Kieran.O'Leary@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
|
|
Now that we have the EP93xx DMA engine driver in place, we convert the ASoC
drivers (I2S, AC97 and PCM) to take advantage of this new API. There are no
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Don't require an audio rate SYSCLK in hw_params() in order to better
support microphone detection use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ReTune Mobile modes are not currently supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
We really should be getting the interrupt - if we don't get one it's very
likely that the configuration is incorrect and audio will fail. Also
increase the timeout substantially in this case for safety.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
The chip can actually support SPI so we shouldn't assume we've got an I2C
device even though that's the most common configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Currently the rbtree code will write out the entire register map when
doing a cache sync which is wasteful and will slow things down. Check
to see if the value we're about to write is the default and don't bother
restoring it if it is, either the value will have been retained or the
device will have been reset and holds the value already.
We should really store the defaults in the nodes but this resolves the
immediate issue.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
|
|
Some ASoC components depend on other ASoC components to provide clocks and
power resources in order to probe() and vice versa for remove().
Allow components to be ordered so that components can be probed() and removed()
in sequences that conform to their dependencies.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
Instead of checking the azx_dev index with a fixed number (4), check
the stream direction of the assigned substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When reading from the position-buffer results in -1, handle as it's
invalid and falls back to LPIB mode as well as 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
Commit f97d0c6d5f94 ("ASoC: AD1836: Add input gain control for ADC2") contained
a typo in the register name, causing a build error. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
removing unnecessary if(ret) checks
This updated patch corrects a minor spelling problem in the commit message
and resolves two other (similar) issues found in wm8940.c by Jonathan Cameron.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
BugLink: https://launchpad.net/bugs/792712
The original reporter states that sound from the internal speakers is
inaudible until using the model=auto quirk. This symptom is due to an
existing quirk mask for 0x102802b* that uses the model=dell quirk. To
limit the possible regressions, leave the existing quirk mask but add
a higher priority specific mask for the reporter's PCI SSID.
Reported-and-tested-by: rodni hipp
Cc: <stable@kernel.org> [2.6.38+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
The AD1836 has a PGA for its second ADC. This patch adds a control for
adjusting the the gain of the PGA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The control_type field is never used, so it can be removed. The
control_data field is used to initialize the codec's control_data field,
but since this is also done by the snd-soc-cache core, the redundant
assignment can be removed and the field can be dropped.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The AD183X codec devices are mostly register compatible and can easily be
supported by the same driver. The main difference between those devices
is the number of DACs and ADCs.
This patch adjusts the driver to allocate the controls, DAPM widgets and
routes for the DACs and ADCs dynamically based on the chip type.
The AD1836 is a bit special in that it supports different modes for its second
ADC, so it needs some special handling. Right now the driver hardcodes the mode
to the differential PGA mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The different ADC and DAC controls follow the same scheme, so add some helper
macros for declaring them.
This should make the code a bit more readable and also decreases the code size
a bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Now that the CODEC driver supports it defer configuration of the system
clock until bias management which is a much more idiomatic place to do
system power control and makes things a lot more happy when we're using
both interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|