From b7fb14d3ac63117e0e8beabe75f4ea52051fbe3a Mon Sep 17 00:00:00 2001 From: Christoph Hellwig Date: Wed, 16 Jun 2021 15:46:58 +0200 Subject: ide: remove the legacy ide driver The legay ide driver has been replace with libata starting in 2003 and has been scheduled for removal for a while. Finally kill it off so that we can start cleaning up various bits of cruft it forced on the block layer. Signed-off-by: Christoph Hellwig Signed-off-by: Jens Axboe --- Documentation/userspace-api/ioctl/hdio.rst | 845 +---------------------------- 1 file changed, 25 insertions(+), 820 deletions(-) (limited to 'Documentation/userspace-api') diff --git a/Documentation/userspace-api/ioctl/hdio.rst b/Documentation/userspace-api/ioctl/hdio.rst index 817371bf94e9..6ee8fc88699f 100644 --- a/Documentation/userspace-api/ioctl/hdio.rst +++ b/Documentation/userspace-api/ioctl/hdio.rst @@ -7,8 +7,8 @@ Summary of `HDIO_` ioctl calls November, 2004 This document attempts to describe the ioctl(2) calls supported by -the HD/IDE layer. These are by-and-large implemented (as of Linux 2.6) -in drivers/ide/ide.c and drivers/block/scsi_ioctl.c +the HD/IDE layer. These are by-and-large implemented (as of Linux 5.11) +drivers/ata/libata-scsi.c. ioctl values are listed in . As of this writing, they are as follows: @@ -17,50 +17,17 @@ are as follows: ======================= ======================================= HDIO_GETGEO get device geometry - HDIO_GET_UNMASKINTR get current unmask setting - HDIO_GET_MULTCOUNT get current IDE blockmode setting - HDIO_GET_QDMA get use-qdma flag - HDIO_SET_XFER set transfer rate via proc - HDIO_OBSOLETE_IDENTITY OBSOLETE, DO NOT USE - HDIO_GET_KEEPSETTINGS get keep-settings-on-reset flag HDIO_GET_32BIT get current io_32bit setting - HDIO_GET_NOWERR get ignore-write-error flag - HDIO_GET_DMA get use-dma flag - HDIO_GET_NICE get nice flags HDIO_GET_IDENTITY get IDE identification info - HDIO_GET_WCACHE get write cache mode on|off - HDIO_GET_ACOUSTIC get acoustic value - HDIO_GET_ADDRESS get sector addressing mode - HDIO_GET_BUSSTATE get the bus state of the hwif - HDIO_TRISTATE_HWIF execute a channel tristate - HDIO_DRIVE_RESET execute a device reset HDIO_DRIVE_TASKFILE execute raw taskfile HDIO_DRIVE_TASK execute task and special drive command HDIO_DRIVE_CMD execute a special drive command - HDIO_DRIVE_CMD_AEB HDIO_DRIVE_TASK ======================= ======================================= ioctls that pass non-pointer values: ======================= ======================================= - HDIO_SET_MULTCOUNT change IDE blockmode - HDIO_SET_UNMASKINTR permit other irqs during I/O - HDIO_SET_KEEPSETTINGS keep ioctl settings on reset HDIO_SET_32BIT change io_32bit flags - HDIO_SET_NOWERR change ignore-write-error flag - HDIO_SET_DMA change use-dma flag - HDIO_SET_PIO_MODE reconfig interface to new speed - HDIO_SCAN_HWIF register and (re)scan interface - HDIO_SET_NICE set nice flags - HDIO_UNREGISTER_HWIF unregister interface - HDIO_SET_WCACHE change write cache enable-disable - HDIO_SET_ACOUSTIC change acoustic behavior - HDIO_SET_BUSSTATE set the bus state of the hwif - HDIO_SET_QDMA change use-qdma flag - HDIO_SET_ADDRESS change lba addressing modes - - HDIO_SET_IDE_SCSI Set scsi emulation mode on/off - HDIO_SET_SCSI_IDE not implemented yet ======================= ======================================= @@ -137,512 +104,49 @@ HDIO_GETGEO - -HDIO_GET_UNMASKINTR - get current unmask setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_UNMASKINTR, &val); - - inputs: - none - - - - outputs: - The value of the drive's current unmask setting - - - - - -HDIO_SET_UNMASKINTR - permit other irqs during I/O - - - usage:: - - unsigned long val; - - ioctl(fd, HDIO_SET_UNMASKINTR, val); - - inputs: - New value for unmask flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - - -HDIO_GET_MULTCOUNT - get current IDE blockmode setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_MULTCOUNT, &val); - - inputs: - none - - - - outputs: - The value of the current IDE block mode setting. This - controls how many sectors the drive will transfer per - interrupt. - - - -HDIO_SET_MULTCOUNT - change IDE blockmode - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_MULTCOUNT, val); - - inputs: - New value for IDE block mode setting. This controls how many - sectors the drive will transfer per interrupt. - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range supported by disk. - - EBUSY Controller busy or blockmode already set. - - EIO Drive did not accept new block mode. - - notes: - Source code comments read:: - - This is tightly woven into the driver->do_special cannot - touch. DON'T do it again until a total personality rewrite - is committed. - - If blockmode has already been set, this ioctl will fail with - -EBUSY - - - -HDIO_GET_QDMA - get use-qdma flag - - - Not implemented, as of 2.6.8.1 - - - -HDIO_SET_XFER - set transfer rate via proc - - - Not implemented, as of 2.6.8.1 - - - -HDIO_OBSOLETE_IDENTITY - OBSOLETE, DO NOT USE - - - Same as HDIO_GET_IDENTITY (see below), except that it only - returns the first 142 bytes of drive identity information. - - - -HDIO_GET_IDENTITY - get IDE identification info - - - usage:: - - unsigned char identity[512]; - - ioctl(fd, HDIO_GET_IDENTITY, identity); - - inputs: - none - - - - outputs: - ATA drive identity information. For full description, see - the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in - the ATA specification. - - error returns: - - EINVAL Called on a partition instead of the whole disk device - - ENOMSG IDENTIFY DEVICE information not available - - notes: - Returns information that was obtained when the drive was - probed. Some of this information is subject to change, and - this ioctl does not re-probe the drive to update the - information. - - This information is also available from /proc/ide/hdX/identify - - - -HDIO_GET_KEEPSETTINGS - get keep-settings-on-reset flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_KEEPSETTINGS, &val); - - inputs: - none - - - - outputs: - The value of the current "keep settings" flag - - - - notes: - When set, indicates that kernel should restore settings - after a drive reset. - - - -HDIO_SET_KEEPSETTINGS - keep ioctl settings on reset - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_KEEPSETTINGS, val); - - inputs: - New value for keep_settings flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_GET_32BIT - get current io_32bit setting - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_32BIT, &val); - - inputs: - none - - - - outputs: - The value of the current io_32bit setting - - - - notes: - 0=16-bit, 1=32-bit, 2,3 = 32bit+sync - - - - - -HDIO_GET_NOWERR - get ignore-write-error flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_NOWERR, &val); - - inputs: - none - - - - outputs: - The value of the current ignore-write-error flag - - - - - -HDIO_GET_DMA - get use-dma flag - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_DMA, &val); - - inputs: - none - - - - outputs: - The value of the current use-dma flag - - - - - -HDIO_GET_NICE - get nice flags - - - usage:: - - long nice; - - ioctl(fd, HDIO_GET_NICE, &nice); - - inputs: - none - - - - outputs: - The drive's "nice" values. - - - - notes: - Per-drive flags which determine when the system will give more - bandwidth to other devices sharing the same IDE bus. - - See , near symbol IDE_NICE_DSC_OVERLAP. - - - - -HDIO_SET_NICE - set nice flags - - - usage:: - - unsigned long nice; - - ... - ioctl(fd, HDIO_SET_NICE, nice); - - inputs: - bitmask of nice flags. - - - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - EPERM Flags other than DSC_OVERLAP and NICE_1 set. - - EPERM DSC_OVERLAP specified but not supported by drive - - notes: - This ioctl sets the DSC_OVERLAP and NICE_1 flags from values - provided by the user. - - Nice flags are listed in , starting with - IDE_NICE_DSC_OVERLAP. These values represent shifts. - - - - - -HDIO_GET_WCACHE - get write cache mode on|off - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_WCACHE, &val); - - inputs: - none - - - - outputs: - The value of the current write cache mode - - - - - -HDIO_GET_ACOUSTIC - get acoustic value - - - usage:: - - long val; - - ioctl(fd, HDIO_GET_ACOUSTIC, &val); - - inputs: - none - - - - outputs: - The value of the current acoustic settings - - - - notes: - See HDIO_SET_ACOUSTIC - - - - - -HDIO_GET_ADDRESS - usage:: - - - long val; - - ioctl(fd, HDIO_GET_ADDRESS, &val); - - inputs: - none - - - - outputs: - The value of the current addressing mode: - - = =================== - 0 28-bit - 1 48-bit - 2 48-bit doing 28-bit - 3 64-bit - = =================== - - - -HDIO_GET_BUSSTATE - get the bus state of the hwif - - - usage:: - - long state; - - ioctl(fd, HDIO_SCAN_HWIF, &state); - - inputs: - none - - - - outputs: - Current power state of the IDE bus. One of BUSSTATE_OFF, - BUSSTATE_ON, or BUSSTATE_TRISTATE - - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - - - -HDIO_SET_BUSSTATE - set the bus state of the hwif +HDIO_GET_IDENTITY + get IDE identification info usage:: - int state; + unsigned char identity[512]; - ... - ioctl(fd, HDIO_SCAN_HWIF, state); + ioctl(fd, HDIO_GET_IDENTITY, identity); inputs: - Desired IDE power state. One of BUSSTATE_OFF, BUSSTATE_ON, - or BUSSTATE_TRISTATE - - outputs: none - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - EOPNOTSUPP Hardware interface does not support bus power control - - - + outputs: + ATA drive identity information. For full description, see + the IDENTIFY DEVICE and IDENTIFY PACKET DEVICE commands in + the ATA specification. -HDIO_TRISTATE_HWIF - execute a channel tristate + error returns: + - EINVAL Called on a partition instead of the whole disk device + - ENOMSG IDENTIFY DEVICE information not available + notes: + Returns information that was obtained when the drive was + probed. Some of this information is subject to change, and + this ioctl does not re-probe the drive to update the + information. - Not implemented, as of 2.6.8.1. See HDIO_SET_BUSSTATE + This information is also available from /proc/ide/hdX/identify -HDIO_DRIVE_RESET - execute a device reset +HDIO_GET_32BIT + get current io_32bit setting usage:: - int args[3] + long val; - ... - ioctl(fd, HDIO_DRIVE_RESET, args); + ioctl(fd, HDIO_GET_32BIT, &val); inputs: none @@ -650,22 +154,12 @@ HDIO_DRIVE_RESET outputs: - none - + The value of the current io_32bit setting - error returns: - - EACCES Access denied: requires CAP_SYS_ADMIN - - ENXIO No such device: phy dead or ctl_addr == 0 - - EIO I/O error: reset timed out or hardware error notes: - - - Execute a reset on the device as soon as the current IO - operation has completed. - - - Executes an ATAPI soft reset if applicable, otherwise - executes an ATA soft reset on the controller. + 0=16-bit, 1=32-bit, 2,3 = 32bit+sync @@ -1026,14 +520,6 @@ HDIO_DRIVE_TASK -HDIO_DRIVE_CMD_AEB - HDIO_DRIVE_TASK - - - Not implemented, as of 2.6.8.1 - - - HDIO_SET_32BIT change io_32bit flags @@ -1059,284 +545,3 @@ HDIO_SET_32BIT - EACCES Access denied: requires CAP_SYS_ADMIN - EINVAL value out of range [0 3] - EBUSY Controller busy - - - - -HDIO_SET_NOWERR - change ignore-write-error flag - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_NOWERR, val); - - inputs: - New value for ignore-write-error flag. Used for ignoring - - - WRERR_STAT - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_DMA - change use-dma flag - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_DMA, val); - - inputs: - New value for use-dma flag - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_PIO_MODE - reconfig interface to new speed - - - usage:: - - long val; - - ioctl(fd, HDIO_SET_PIO_MODE, val); - - inputs: - New interface speed. - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 255] - - EBUSY Controller busy - - - -HDIO_SCAN_HWIF - register and (re)scan interface - - - usage:: - - int args[3] - - ... - ioctl(fd, HDIO_SCAN_HWIF, args); - - inputs: - - ======= ========================= - args[0] io address to probe - - - args[1] control address to probe - args[2] irq number - ======= ========================= - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - EIO Probe failed. - - notes: - This ioctl initializes the addresses and irq for a disk - controller, probes for drives, and creates /proc/ide - interfaces as appropriate. - - - -HDIO_UNREGISTER_HWIF - unregister interface - - - usage:: - - int index; - - ioctl(fd, HDIO_UNREGISTER_HWIF, index); - - inputs: - index index of hardware interface to unregister - - - - outputs: - none - - - - error returns: - - EACCES Access denied: requires CAP_SYS_RAWIO - - notes: - This ioctl removes a hardware interface from the kernel. - - Currently (2.6.8) this ioctl silently fails if any drive on - the interface is busy. - - - -HDIO_SET_WCACHE - change write cache enable-disable - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_WCACHE, val); - - inputs: - New value for write cache enable - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_ACOUSTIC - change acoustic behavior - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_ACOUSTIC, val); - - inputs: - New value for drive acoustic settings - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 254] - - EBUSY Controller busy - - - -HDIO_SET_QDMA - change use-qdma flag - - - Not implemented, as of 2.6.8.1 - - - -HDIO_SET_ADDRESS - change lba addressing modes - - - usage:: - - int val; - - ioctl(fd, HDIO_SET_ADDRESS, val); - - inputs: - New value for addressing mode - - = =================== - 0 28-bit - 1 48-bit - 2 48-bit doing 28-bit - = =================== - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 2] - - EBUSY Controller busy - - EIO Drive does not support lba48 mode. - - -HDIO_SET_IDE_SCSI - usage:: - - - long val; - - ioctl(fd, HDIO_SET_IDE_SCSI, val); - - inputs: - New value for scsi emulation mode (?) - - - - outputs: - none - - - - error return: - - EINVAL Called on a partition instead of the whole disk device - - EACCES Access denied: requires CAP_SYS_ADMIN - - EINVAL value out of range [0 1] - - EBUSY Controller busy - - - -HDIO_SET_SCSI_IDE - Not implemented, as of 2.6.8.1 -- cgit v1.2.3