summaryrefslogtreecommitdiff
path: root/Documentation/userspace-api/media/rc/lirc-dev-intro.rst
blob: 167b354bf05157b9e89e542da6ef61908e7f0e11 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
.. SPDX-License-Identifier: GFDL-1.1-no-invariants-or-later

.. _lirc_dev_intro:

************
Introduction
************

LIRC stands for Linux Infrared Remote Control. The LIRC device interface is
a bi-directional interface for transporting raw IR and decoded scancodes
data between userspace and kernelspace. Fundamentally, it is just a chardev
(/dev/lircX, for X = 0, 1, 2, ...), with a number of standard struct
file_operations defined on it. With respect to transporting raw IR and
decoded scancodes to and fro, the essential fops are read, write and ioctl.

It is also possible to attach a BPF program to a LIRC device for decoding
raw IR into scancodes.

Example dmesg output upon a driver registering w/LIRC:

.. code-block:: none

    $ dmesg |grep lirc_dev
    rc rc0: lirc_dev: driver mceusb registered at minor = 0, raw IR receiver, raw IR transmitter

What you should see for a chardev:

.. code-block:: none

    $ ls -l /dev/lirc*
    crw-rw---- 1 root root 248, 0 Jul 2 22:20 /dev/lirc0

Note that the package `v4l-utils <https://git.linuxtv.org/v4l-utils.git/>`_
contains tools for working with LIRC devices:

 - ir-ctl: can receive raw IR and transmit IR, as well as query LIRC
   device features.

 - ir-keytable: can load keymaps; allows you to set IR kernel protocols; load
   BPF IR decoders and test IR decoding. Some BPF IR decoders are also
   provided.

.. _lirc_modes:

**********
LIRC modes
**********

LIRC supports some modes of receiving and sending IR codes, as shown
on the following table.

.. _lirc-mode-scancode:
.. _lirc-scancode-flag-toggle:
.. _lirc-scancode-flag-repeat:

``LIRC_MODE_SCANCODE``

    This mode is for both sending and receiving IR.

    For transmitting (aka sending), create a ``struct lirc_scancode`` with
    the desired scancode set in the ``scancode`` member, :c:type:`rc_proto`
    set to the :ref:`IR protocol <Remote_controllers_Protocols>`, and all other
    members set to 0. Write this struct to the lirc device.

    For receiving, you read ``struct lirc_scancode`` from the LIRC device.
    The ``scancode`` field is set to the received scancode and the
    :ref:`IR protocol <Remote_controllers_Protocols>` is set in
    :c:type:`rc_proto`. If the scancode maps to a valid key code, this is set
    in the ``keycode`` field, else it is set to ``KEY_RESERVED``.

    The ``flags`` can have ``LIRC_SCANCODE_FLAG_TOGGLE`` set if the toggle
    bit is set in protocols that support it (e.g. rc-5 and rc-6), or
    ``LIRC_SCANCODE_FLAG_REPEAT`` for when a repeat is received for protocols
    that support it (e.g. nec).

    In the Sanyo and NEC protocol, if you hold a button on remote, rather than
    repeating the entire scancode, the remote sends a shorter message with
    no scancode, which just means button is held, a "repeat". When this is
    received, the ``LIRC_SCANCODE_FLAG_REPEAT`` is set and the scancode and
    keycode is repeated.

    With nec, there is no way to distinguish "button hold" from "repeatedly
    pressing the same button". The rc-5 and rc-6 protocols have a toggle bit.
    When a button is released and pressed again, the toggle bit is inverted.
    If the toggle bit is set, the ``LIRC_SCANCODE_FLAG_TOGGLE`` is set.

    The ``timestamp`` field is filled with the time nanoseconds
    (in ``CLOCK_MONOTONIC``) when the scancode was decoded.

.. _lirc-mode-mode2:

``LIRC_MODE_MODE2``

    The driver returns a sequence of pulse and space codes to userspace,
    as a series of u32 values.

    This mode is used only for IR receive.

    The upper 8 bits determine the packet type, and the lower 24 bits
    the payload. Use ``LIRC_VALUE()`` macro to get the payload, and
    the macro ``LIRC_MODE2()`` will give you the type, which
    is one of:

    ``LIRC_MODE2_PULSE``

        Signifies the presence of IR in microseconds.

    ``LIRC_MODE2_SPACE``

        Signifies absence of IR in microseconds.

    ``LIRC_MODE2_FREQUENCY``

        If measurement of the carrier frequency was enabled with
        :ref:`lirc_set_measure_carrier_mode` then this packet gives you
        the carrier frequency in Hertz.

    ``LIRC_MODE2_TIMEOUT``

        If timeout reports are enabled with
        :ref:`lirc_set_rec_timeout_reports`, when the timeout set with
        :ref:`lirc_set_rec_timeout` expires due to no IR being detected,
        this packet will be sent, with the number of microseconds with
        no IR.

.. _lirc-mode-pulse:

``LIRC_MODE_PULSE``

    In pulse mode, a sequence of pulse/space integer values are written to the
    lirc device using :ref:`lirc-write`.

    The values are alternating pulse and space lengths, in microseconds. The
    first and last entry must be a pulse, so there must be an odd number
    of entries.

    This mode is used only for IR send.

********************
BPF based IR decoder
********************

The kernel has support for decoding the most common
:ref:`IR protocols <Remote_controllers_Protocols>`, but there
are many protocols which are not supported. To support these, it is possible
to load an BPF program which does the decoding. This can only be done on
LIRC devices which support reading raw IR.

First, using the `bpf(2)`_ syscall with the ``BPF_LOAD_PROG`` argument,
program must be loaded of type ``BPF_PROG_TYPE_LIRC_MODE2``. Once attached
to the LIRC device, this program will be called for each pulse, space or
timeout event on the LIRC device. The context for the BPF program is a
pointer to a unsigned int, which is a :ref:`LIRC_MODE_MODE2 <lirc-mode-mode2>`
value. When the program has decoded the scancode, it can be submitted using
the BPF functions ``bpf_rc_keydown()`` or ``bpf_rc_repeat()``. Mouse or pointer
movements can be reported using ``bpf_rc_pointer_rel()``.

Once you have the file descriptor for the ``BPF_PROG_TYPE_LIRC_MODE2`` BPF
program, it can be attached to the LIRC device using the `bpf(2)`_ syscall.
The target must be the file descriptor for the LIRC device, and the
attach type must be ``BPF_LIRC_MODE2``. No more than 64 BPF programs can be
attached to a single LIRC device at a time.

.. _bpf(2): http://man7.org/linux/man-pages/man2/bpf.2.html