1 files changed, 18 insertions, 122 deletions

diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
index d52651a05daa..e237602e10ea 100644
--- a/arch/arm/mach-omap2/omap_phy_internal.c
+++ b/arch/arm/mach-omap2/omap_phy_internal.c
@@ -27,147 +27,43 @@
 #include <linux/io.h>
 #include <linux/err.h>
 #include <linux/usb.h>
+#include <linux/usb/musb.h>
 
-#include <plat/usb.h>
+#include "soc.h"
 #include "control.h"
+#include "usb.h"
 
-/* OMAP control module register for UTMI PHY */
 #define CONTROL_DEV_CONF		0x300
 #define PHY_PD				0x1
 
-#define USBOTGHS_CONTROL		0x33c
-#define	AVALID				BIT(0)
-#define	BVALID				BIT(1)
-#define	VBUSVALID			BIT(2)
-#define	SESSEND				BIT(3)
-#define	IDDIG				BIT(4)
+/**
+ * omap4430_phy_power_down: disable MUSB PHY during early init
+ *
+ * OMAP4 MUSB PHY module is enabled by default on reset, but this will
+ * prevent core retention if not disabled by SW. USB driver will
+ * later on enable this, once and if the driver needs it.
+ */
+static int __init omap4430_phy_power_down(void)
+{
+	void __iomem *ctrl_base;
 
-static struct clk *phyclk, *clk48m, *clk32k;
-static void __iomem *ctrl_base;
-static int usbotghs_control;
+	if (!cpu_is_omap44xx())
+		return 0;
 
-int omap4430_phy_init(struct device *dev)
-{
 	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
 	if (!ctrl_base) {
 		pr_err("control module ioremap failed\n");
 		return -ENOMEM;
 	}
+
 	/* Power down the phy */
 	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
 
-	if (!dev) {
-		iounmap(ctrl_base);
-		return 0;
-	}
-
-	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
-	if (IS_ERR(phyclk)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
-		iounmap(ctrl_base);
-		return PTR_ERR(phyclk);
-	}
-
-	clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m");
-	if (IS_ERR(clk48m)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n");
-		clk_put(phyclk);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk48m);
-	}
-
-	clk32k = clk_get(dev, "usb_phy_cm_clk32k");
-	if (IS_ERR(clk32k)) {
-		dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n");
-		clk_put(phyclk);
-		clk_put(clk48m);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk32k);
-	}
-	return 0;
-}
-
-int omap4430_phy_set_clk(struct device *dev, int on)
-{
-	static int state;
-
-	if (on && !state) {
-		/* Enable the phy clocks */
-		clk_enable(phyclk);
-		clk_enable(clk48m);
-		clk_enable(clk32k);
-		state = 1;
-	} else if (state) {
-		/* Disable the phy clocks */
-		clk_disable(phyclk);
-		clk_disable(clk48m);
-		clk_disable(clk32k);
-		state = 0;
-	}
-	return 0;
-}
-
-int omap4430_phy_power(struct device *dev, int ID, int on)
-{
-	if (on) {
-		if (ID)
-			/* enable VBUS valid, IDDIG groung */
-			__raw_writel(AVALID | VBUSVALID, ctrl_base +
-							USBOTGHS_CONTROL);
-		else
-			/*
-			 * Enable VBUS Valid, AValid and IDDIG
-			 * high impedance
-			 */
-			__raw_writel(IDDIG | AVALID | VBUSVALID,
-						ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable session END and IDIG to high impedance. */
-		__raw_writel(SESSEND | IDDIG, ctrl_base +
-					USBOTGHS_CONTROL);
-	}
-	return 0;
-}
-
-int omap4430_phy_suspend(struct device *dev, int suspend)
-{
-	if (suspend) {
-		/* Disable the clocks */
-		omap4430_phy_set_clk(dev, 0);
-		/* Power down the phy */
-		__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-		/* save the context */
-		usbotghs_control = __raw_readl(ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable the internel phy clcoks */
-		omap4430_phy_set_clk(dev, 1);
-		/* power on the phy */
-		if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) {
-			__raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-			mdelay(200);
-		}
-
-		/* restore the context */
-		__raw_writel(usbotghs_control, ctrl_base + USBOTGHS_CONTROL);
-	}
-
-	return 0;
-}
-
-int omap4430_phy_exit(struct device *dev)
-{
-	if (ctrl_base)
-		iounmap(ctrl_base);
-	if (phyclk)
-		clk_put(phyclk);
-	if (clk48m)
-		clk_put(clk48m);
-	if (clk32k)
-		clk_put(clk32k);
+	iounmap(ctrl_base);
 
 	return 0;
 }
+early_initcall(omap4430_phy_power_down);
 
 void am35x_musb_reset(void)
 {