diff options
Diffstat (limited to 'drivers')
42 files changed, 320 insertions, 213 deletions
diff --git a/drivers/md/dm-ioctl.c b/drivers/md/dm-ioctl.c index c8a18e4ee9dc..720ceeb7fa9b 100644 --- a/drivers/md/dm-ioctl.c +++ b/drivers/md/dm-ioctl.c @@ -1298,21 +1298,22 @@ static int table_load(struct dm_ioctl *param, size_t param_size) goto err_unlock_md_type; } - if (dm_get_md_type(md) == DM_TYPE_NONE) + if (dm_get_md_type(md) == DM_TYPE_NONE) { /* Initial table load: acquire type of table. */ dm_set_md_type(md, dm_table_get_type(t)); - else if (dm_get_md_type(md) != dm_table_get_type(t)) { + + /* setup md->queue to reflect md's type (may block) */ + r = dm_setup_md_queue(md); + if (r) { + DMWARN("unable to set up device queue for new table."); + goto err_unlock_md_type; + } + } else if (dm_get_md_type(md) != dm_table_get_type(t)) { DMWARN("can't change device type after initial table load."); r = -EINVAL; goto err_unlock_md_type; } - /* setup md->queue to reflect md's type (may block) */ - r = dm_setup_md_queue(md); - if (r) { - DMWARN("unable to set up device queue for new table."); - goto err_unlock_md_type; - } dm_unlock_md_type(md); /* stage inactive table */ diff --git a/drivers/md/dm.c b/drivers/md/dm.c index f8c7ca3e8947..a930b72314ac 100644 --- a/drivers/md/dm.c +++ b/drivers/md/dm.c @@ -1082,18 +1082,26 @@ static void rq_completed(struct mapped_device *md, int rw, bool run_queue) dm_put(md); } -static void free_rq_clone(struct request *clone) +static void free_rq_clone(struct request *clone, bool must_be_mapped) { struct dm_rq_target_io *tio = clone->end_io_data; struct mapped_device *md = tio->md; + WARN_ON_ONCE(must_be_mapped && !clone->q); + blk_rq_unprep_clone(clone); - if (clone->q->mq_ops) + if (md->type == DM_TYPE_MQ_REQUEST_BASED) + /* stacked on blk-mq queue(s) */ tio->ti->type->release_clone_rq(clone); else if (!md->queue->mq_ops) /* request_fn queue stacked on request_fn queue(s) */ free_clone_request(md, clone); + /* + * NOTE: for the blk-mq queue stacked on request_fn queue(s) case: + * no need to call free_clone_request() because we leverage blk-mq by + * allocating the clone at the end of the blk-mq pdu (see: clone_rq) + */ if (!md->queue->mq_ops) free_rq_tio(tio); @@ -1124,7 +1132,7 @@ static void dm_end_request(struct request *clone, int error) rq->sense_len = clone->sense_len; } - free_rq_clone(clone); + free_rq_clone(clone, true); if (!rq->q->mq_ops) blk_end_request_all(rq, error); else @@ -1143,7 +1151,7 @@ static void dm_unprep_request(struct request *rq) } if (clone) - free_rq_clone(clone); + free_rq_clone(clone, false); } /* @@ -2662,9 +2670,6 @@ static int dm_init_request_based_queue(struct mapped_device *md) { struct request_queue *q = NULL; - if (md->queue->elevator) - return 0; - /* Fully initialize the queue */ q = blk_init_allocated_queue(md->queue, dm_request_fn, NULL); if (!q) diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 78dde56ae6e6..3a10551d64cf 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -82,6 +82,8 @@ #include <net/bond_3ad.h> #include <net/bond_alb.h> +#include "bonding_priv.h" + /*---------------------------- Module parameters ----------------------------*/ /* monitor all links that often (in milliseconds). <=0 disables monitoring */ diff --git a/drivers/net/bonding/bond_procfs.c b/drivers/net/bonding/bond_procfs.c index 62694cfc05b6..b20b35acb47d 100644 --- a/drivers/net/bonding/bond_procfs.c +++ b/drivers/net/bonding/bond_procfs.c @@ -4,6 +4,7 @@ #include <net/netns/generic.h> #include <net/bonding.h> +#include "bonding_priv.h" static void *bond_info_seq_start(struct seq_file *seq, loff_t *pos) __acquires(RCU) diff --git a/drivers/net/bonding/bonding_priv.h b/drivers/net/bonding/bonding_priv.h new file mode 100644 index 000000000000..5a4d81a9437c --- /dev/null +++ b/drivers/net/bonding/bonding_priv.h @@ -0,0 +1,25 @@ +/* + * Bond several ethernet interfaces into a Cisco, running 'Etherchannel'. + * + * Portions are (c) Copyright 1995 Simon "Guru Aleph-Null" Janes + * NCM: Network and Communications Management, Inc. + * + * BUT, I'm the one who modified it for ethernet, so: + * (c) Copyright 1999, Thomas Davis, tadavis@lbl.gov + * + * This software may be used and distributed according to the terms + * of the GNU Public License, incorporated herein by reference. + * + */ + +#ifndef _BONDING_PRIV_H +#define _BONDING_PRIV_H + +#define DRV_VERSION "3.7.1" +#define DRV_RELDATE "April 27, 2011" +#define DRV_NAME "bonding" +#define DRV_DESCRIPTION "Ethernet Channel Bonding Driver" + +#define bond_version DRV_DESCRIPTION ": v" DRV_VERSION " (" DRV_RELDATE ")\n" + +#endif diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index 58808f651452..e8c96b8e86f4 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -112,7 +112,7 @@ config PCH_CAN config CAN_GRCAN tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" - depends on OF + depends on OF && HAS_DMA ---help--- Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. Note that the driver supports little endian, even though little diff --git a/drivers/net/can/usb/kvaser_usb.c b/drivers/net/can/usb/kvaser_usb.c index 4643914859b2..8b17a9065b0b 100644 --- a/drivers/net/can/usb/kvaser_usb.c +++ b/drivers/net/can/usb/kvaser_usb.c @@ -1102,7 +1102,7 @@ static void kvaser_usb_rx_can_err(const struct kvaser_usb_net_priv *priv, if (msg->u.rx_can_header.flag & (MSG_FLAG_ERROR_FRAME | MSG_FLAG_NERR)) { - netdev_err(priv->netdev, "Unknow error (flags: 0x%02x)\n", + netdev_err(priv->netdev, "Unknown error (flags: 0x%02x)\n", msg->u.rx_can_header.flag); stats->rx_errors++; diff --git a/drivers/net/ethernet/8390/etherh.c b/drivers/net/ethernet/8390/etherh.c index b36ee9e0d220..d686b9cac29f 100644 --- a/drivers/net/ethernet/8390/etherh.c +++ b/drivers/net/ethernet/8390/etherh.c @@ -523,7 +523,7 @@ static int etherh_addr(char *addr, struct expansion_card *ec) char *s; if (!ecard_readchunk(&cd, ec, 0xf5, 0)) { - printk(KERN_ERR "%s: unable to read podule description string\n", + printk(KERN_ERR "%s: unable to read module description string\n", dev_name(&ec->dev)); goto no_addr; } diff --git a/drivers/net/ethernet/altera/altera_msgdmahw.h b/drivers/net/ethernet/altera/altera_msgdmahw.h index eba070f16782..89cd11d86642 100644 --- a/drivers/net/ethernet/altera/altera_msgdmahw.h +++ b/drivers/net/ethernet/altera/altera_msgdmahw.h @@ -58,15 +58,12 @@ struct msgdma_extended_desc { /* Tx buffer control flags */ #define MSGDMA_DESC_CTL_TX_FIRST (MSGDMA_DESC_CTL_GEN_SOP | \ - MSGDMA_DESC_CTL_TR_ERR_IRQ | \ MSGDMA_DESC_CTL_GO) -#define MSGDMA_DESC_CTL_TX_MIDDLE (MSGDMA_DESC_CTL_TR_ERR_IRQ | \ - MSGDMA_DESC_CTL_GO) +#define MSGDMA_DESC_CTL_TX_MIDDLE (MSGDMA_DESC_CTL_GO) #define MSGDMA_DESC_CTL_TX_LAST (MSGDMA_DESC_CTL_GEN_EOP | \ MSGDMA_DESC_CTL_TR_COMP_IRQ | \ - MSGDMA_DESC_CTL_TR_ERR_IRQ | \ MSGDMA_DESC_CTL_GO) #define MSGDMA_DESC_CTL_TX_SINGLE (MSGDMA_DESC_CTL_GEN_SOP | \ diff --git a/drivers/net/ethernet/altera/altera_tse_main.c b/drivers/net/ethernet/altera/altera_tse_main.c index 90a76306ad0f..0533c051a3e5 100644 --- a/drivers/net/ethernet/altera/altera_tse_main.c +++ b/drivers/net/ethernet/altera/altera_tse_main.c @@ -777,6 +777,8 @@ static int init_phy(struct net_device *dev) struct altera_tse_private *priv = netdev_priv(dev); struct phy_device *phydev; struct device_node *phynode; + bool fixed_link = false; + int rc = 0; /* Avoid init phy in case of no phy present */ if (!priv->phy_iface) @@ -789,13 +791,32 @@ static int init_phy(struct net_device *dev) phynode = of_parse_phandle(priv->device->of_node, "phy-handle", 0); if (!phynode) { - netdev_dbg(dev, "no phy-handle found\n"); - if (!priv->mdio) { - netdev_err(dev, - "No phy-handle nor local mdio specified\n"); - return -ENODEV; + /* check if a fixed-link is defined in device-tree */ + if (of_phy_is_fixed_link(priv->device->of_node)) { + rc = of_phy_register_fixed_link(priv->device->of_node); + if (rc < 0) { + netdev_err(dev, "cannot register fixed PHY\n"); + return rc; + } + + /* In the case of a fixed PHY, the DT node associated + * to the PHY is the Ethernet MAC DT node. + */ + phynode = of_node_get(priv->device->of_node); + fixed_link = true; + + netdev_dbg(dev, "fixed-link detected\n"); + phydev = of_phy_connect(dev, phynode, + &altera_tse_adjust_link, + 0, priv->phy_iface); + } else { + netdev_dbg(dev, "no phy-handle found\n"); + if (!priv->mdio) { + netdev_err(dev, "No phy-handle nor local mdio specified\n"); + return -ENODEV; + } + phydev = connect_local_phy(dev); } - phydev = connect_local_phy(dev); } else { netdev_dbg(dev, "phy-handle found\n"); phydev = of_phy_connect(dev, phynode, @@ -819,10 +840,10 @@ static int init_phy(struct net_device *dev) /* Broken HW is sometimes missing the pull-up resistor on the * MDIO line, which results in reads to non-existent devices returning * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent - * device as well. + * device as well. If a fixed-link is used the phy_id is always 0. * Note: phydev->phy_id is the result of reading the UID PHY registers. */ - if (phydev->phy_id == 0) { + if ((phydev->phy_id == 0) && !fixed_link) { netdev_err(dev, "Bad PHY UID 0x%08x\n", phydev->phy_id); phy_disconnect(phydev); return -ENODEV; diff --git a/drivers/net/ethernet/amd/Kconfig b/drivers/net/ethernet/amd/Kconfig index c638c85f3954..089c269637b7 100644 --- a/drivers/net/ethernet/amd/Kconfig +++ b/drivers/net/ethernet/amd/Kconfig @@ -179,7 +179,7 @@ config SUNLANCE config AMD_XGBE tristate "AMD 10GbE Ethernet driver" - depends on (OF_NET || ACPI) && HAS_IOMEM + depends on (OF_NET || ACPI) && HAS_IOMEM && HAS_DMA select PHYLIB select AMD_XGBE_PHY select BITREVERSE diff --git a/drivers/net/ethernet/arc/Kconfig b/drivers/net/ethernet/arc/Kconfig index 8e262e2b39b6..dea29ee24da4 100644 --- a/drivers/net/ethernet/arc/Kconfig +++ b/drivers/net/ethernet/arc/Kconfig @@ -25,8 +25,7 @@ config ARC_EMAC_CORE config ARC_EMAC tristate "ARC EMAC support" select ARC_EMAC_CORE - depends on OF_IRQ - depends on OF_NET + depends on OF_IRQ && OF_NET && HAS_DMA ---help--- On some legacy ARC (Synopsys) FPGA boards such as ARCAngel4/ML50x non-standard on-chip ethernet device ARC EMAC 10/100 is used. @@ -35,7 +34,7 @@ config ARC_EMAC config EMAC_ROCKCHIP tristate "Rockchip EMAC support" select ARC_EMAC_CORE - depends on OF_IRQ && OF_NET && REGULATOR + depends on OF_IRQ && OF_NET && REGULATOR && HAS_DMA ---help--- Support for Rockchip RK3066/RK3188 EMAC ethernet controllers. This selects Rockchip SoC glue layer support for the diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c index de77d3a74abc..21e3c38c7c75 100644 --- a/drivers/net/ethernet/broadcom/bgmac.c +++ b/drivers/net/ethernet/broadcom/bgmac.c @@ -1260,7 +1260,7 @@ static int bgmac_poll(struct napi_struct *napi, int weight) /* Poll again if more events arrived in the meantime */ if (bgmac_read(bgmac, BGMAC_INT_STATUS) & (BGMAC_IS_TX0 | BGMAC_IS_RX)) - return handled; + return weight; if (handled < weight) { napi_complete(napi); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c index 2f63467bce46..3558a36b1c2d 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c @@ -2485,8 +2485,10 @@ static void bnx2x_bz_fp(struct bnx2x *bp, int index) else if (bp->flags & GRO_ENABLE_FLAG) fp->mode = TPA_MODE_GRO; - /* We don't want TPA on an FCoE L2 ring */ - if (IS_FCOE_FP(fp)) + /* We don't want TPA if it's disabled in bp + * or if this is an FCoE L2 ring. + */ + if (bp->disable_tpa || IS_FCOE_FP(fp)) fp->disable_tpa = 1; } @@ -4809,6 +4811,23 @@ netdev_features_t bnx2x_fix_features(struct net_device *dev, { struct bnx2x *bp = netdev_priv(dev); + if (pci_num_vf(bp->pdev)) { + netdev_features_t changed = dev->features ^ features; + + /* Revert the requested changes in features if they + * would require internal reload of PF in bnx2x_set_features(). + */ + if (!(features & NETIF_F_RXCSUM) && !bp->disable_tpa) { + features &= ~NETIF_F_RXCSUM; + features |= dev->features & NETIF_F_RXCSUM; + } + + if (changed & NETIF_F_LOOPBACK) { + features &= ~NETIF_F_LOOPBACK; + features |= dev->features & NETIF_F_LOOPBACK; + } + } + /* TPA requires Rx CSUM offloading */ if (!(features & NETIF_F_RXCSUM)) { features &= ~NETIF_F_LRO; @@ -4839,15 +4858,18 @@ int bnx2x_set_features(struct net_device *dev, netdev_features_t features) else flags &= ~GRO_ENABLE_FLAG; - if (features & NETIF_F_LOOPBACK) { - if (bp->link_params.loopback_mode != LOOPBACK_BMAC) { - bp->link_params.loopback_mode = LOOPBACK_BMAC; - bnx2x_reload = true; - } - } else { - if (bp->link_params.loopback_mode != LOOPBACK_NONE) { - bp->link_params.loopback_mode = LOOPBACK_NONE; - bnx2x_reload = true; + /* VFs or non SRIOV PFs should be able to change loopback feature */ + if (!pci_num_vf(bp->pdev)) { + if (features & NETIF_F_LOOPBACK) { + if (bp->link_params.loopback_mode != LOOPBACK_BMAC) { + bp->link_params.loopback_mode = LOOPBACK_BMAC; + bnx2x_reload = true; + } + } else { + if (bp->link_params.loopback_mode != LOOPBACK_NONE) { + bp->link_params.loopback_mode = LOOPBACK_NONE; + bnx2x_reload = true; + } } } @@ -4931,6 +4953,11 @@ int bnx2x_resume(struct pci_dev *pdev) } bp = netdev_priv(dev); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, "VFs are enabled, can not change MTU\n"); + return -EPERM; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { BNX2X_ERR("Handling parity error recovery. Try again later\n"); return -EAGAIN; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c index e3d853cab7c9..48ed005ba73f 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c @@ -1843,6 +1843,12 @@ static int bnx2x_set_ringparam(struct net_device *dev, "set ring params command parameters: rx_pending = %d, tx_pending = %d\n", ering->rx_pending, ering->tx_pending); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not change ring parameters\n"); + return -EPERM; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { DP(BNX2X_MSG_ETHTOOL, "Handling parity error recovery. Try again later\n"); @@ -2899,6 +2905,12 @@ static void bnx2x_self_test(struct net_device *dev, u8 is_serdes, link_up; int rc, cnt = 0; + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, + "VFs are enabled, can not perform self test\n"); + return; + } + if (bp->recovery_state != BNX2X_RECOVERY_DONE) { netdev_err(bp->dev, "Handling parity error recovery. Try again later\n"); @@ -3468,6 +3480,11 @@ static int bnx2x_set_channels(struct net_device *dev, channels->rx_count, channels->tx_count, channels->other_count, channels->combined_count); + if (pci_num_vf(bp->pdev)) { + DP(BNX2X_MSG_IOV, "VFs are enabled, can not set channels\n"); + return -EPERM; + } + /* We don't support separate rx / tx channels. * We don't allow setting 'other' channels. */ diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 1270b189a9a2..069952fa5d64 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -18129,7 +18129,9 @@ static pci_ers_result_t tg3_io_error_detected(struct pci_dev *pdev, rtnl_lock(); - tp->pcierr_recovery = true; + /* We needn't recover from permanent error */ + if (state == pci_channel_io_frozen) + tp->pcierr_recovery = true; /* We probably don't have netdev yet */ if (!netdev || !netif_running(netdev)) diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c index 9f5387249f24..665c29098e3c 100644 --- a/drivers/net/ethernet/cadence/macb.c +++ b/drivers/net/ethernet/cadence/macb.c @@ -1473,9 +1473,9 @@ static void macb_init_rings(struct macb *bp) for (i = 0; i < TX_RING_SIZE; i++) { bp->queues[0].tx_ring[i].addr = 0; bp->queues[0].tx_ring[i].ctrl = MACB_BIT(TX_USED); - bp->queues[0].tx_head = 0; - bp->queues[0].tx_tail = 0; } + bp->queues[0].tx_head = 0; + bp->queues[0].tx_tail = 0; bp->queues[0].tx_ring[TX_RING_SIZE - 1].ctrl |= MACB_BIT(TX_WRAP); bp->rx_tail = 0; diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c index 291c87036e17..2a0dc127df3f 100644 --- a/drivers/net/ethernet/ibm/ehea/ehea_main.c +++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c @@ -3347,7 +3347,7 @@ static int ehea_register_memory_hooks(void) { int ret = 0; - if (atomic_inc_and_test(&ehea_memory_hooks_registered)) + if (atomic_inc_return(&ehea_memory_hooks_registered) > 1) return 0; ret = ehea_create_busmap(); @@ -3381,12 +3381,14 @@ out3: out2: unregister_reboot_notifier(&ehea_reboot_nb); out: + atomic_dec(&ehea_memory_hooks_registered); return ret; } static void ehea_unregister_memory_hooks(void) { - if (atomic_read(&ehea_memory_hooks_registered)) + /* Only remove the hooks if we've registered them */ + if (atomic_read(&ehea_memory_hooks_registered) == 0) return; unregister_reboot_notifier(&ehea_reboot_nb); diff --git a/drivers/net/ethernet/ibm/ibmveth.c b/drivers/net/ethernet/ibm/ibmveth.c index cd7675ac5bf9..18134766a114 100644 --- a/drivers/net/ethernet/ibm/ibmveth.c +++ b/drivers/net/ethernet/ibm/ibmveth.c @@ -1238,7 +1238,7 @@ static int ibmveth_change_mtu(struct net_device *dev, int new_mtu) return -EINVAL; for (i = 0; i < IBMVETH_NUM_BUFF_POOLS; i++) - if (new_mtu_oh < adapter->rx_buff_pool[i].buff_size) + if (new_mtu_oh <= adapter->rx_buff_pool[i].buff_size) break; if (i == IBMVETH_NUM_BUFF_POOLS) @@ -1257,7 +1257,7 @@ static int ibmveth_change_mtu(struct net_device *dev, int new_mtu) for (i = 0; i < IBMVETH_NUM_BUFF_POOLS; i++) { adapter->rx_buff_pool[i].active = 1; - if (new_mtu_oh < adapter->rx_buff_pool[i].buff_size) { + if (new_mtu_oh <= adapter->rx_buff_pool[i].buff_size) { dev->mtu = new_mtu; vio_cmo_set_dev_desired(viodev, ibmveth_get_desired_dma diff --git a/drivers/net/ethernet/marvell/pxa168_eth.c b/drivers/net/ethernet/marvell/pxa168_eth.c index af829c578400..7ace07dad6a3 100644 --- a/drivers/net/ethernet/marvell/pxa168_eth.c +++ b/drivers/net/ethernet/marvell/pxa168_eth.c @@ -1508,7 +1508,8 @@ static int pxa168_eth_probe(struct platform_device *pdev) np = of_parse_phandle(pdev->dev.of_node, "phy-handle", 0); if (!np) { dev_err(&pdev->dev, "missing phy-handle\n"); - return -EINVAL; + err = -EINVAL; + goto err_netdev; } of_property_read_u32(np, "reg", &pep->phy_addr); pep->phy_intf = of_get_phy_mode(pdev->dev.of_node); @@ -1526,7 +1527,7 @@ static int pxa168_eth_probe(struct platform_device *pdev) pep->smi_bus = mdiobus_alloc(); if (pep->smi_bus == NULL) { err = -ENOMEM; - goto err_base; + goto err_netdev; } pep->smi_bus->priv = pep; pep->smi_bus->name = "pxa168_eth smi"; @@ -1551,13 +1552,10 @@ err_mdiobus: mdiobus_unregister(pep->smi_bus); err_free_mdio: mdiobus_free(pep->smi_bus); -err_base: - iounmap(pep->base); err_netdev: free_netdev(dev); err_clk: - clk_disable(clk); - clk_put(clk); + clk_disable_unprepare(clk); return err; } @@ -1574,13 +1572,9 @@ static int pxa168_eth_remove(struct platform_device *pdev) if (pep->phy) phy_disconnect(pep->phy); if (pep->clk) { - clk_disable(pep->clk); - clk_put(pep->clk); - pep->clk = NULL; + clk_disable_unprepare(pep->clk); } - iounmap(pep->base); - pep->base = NULL; mdiobus_unregister(pep->smi_bus); mdiobus_free(pep->smi_bus); unregister_netdev(dev); diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c index 3f44e2bbb982..a2ddf3d75ff8 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c @@ -1102,20 +1102,21 @@ static int mlx4_en_check_rxfh_func(struct net_device *dev, u8 hfunc) struct mlx4_en_priv *priv = netdev_priv(dev); /* check if requested function is supported by the device */ - if ((hfunc == ETH_RSS_HASH_TOP && - !(priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_RSS_TOP)) || - (hfunc == ETH_RSS_HASH_XOR && - !(priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_RSS_XOR))) - return -EINVAL; + if (hfunc == ETH_RSS_HASH_TOP) { + if (!(priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_RSS_TOP)) + return -EINVAL; + if (!(dev->features & NETIF_F_RXHASH)) + en_warn(priv, "Toeplitz hash function should be used in conjunction with RX hashing for optimal performance\n"); + return 0; + } else if (hfunc == ETH_RSS_HASH_XOR) { + if (!(priv->mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_RSS_XOR)) + return -EINVAL; + if (dev->features & NETIF_F_RXHASH) + en_warn(priv, "Enabling both XOR Hash function and RX Hashing can limit RPS functionality\n"); + return 0; + } - priv->rss_hash_fn = hfunc; - if (hfunc == ETH_RSS_HASH_TOP && !(dev->features & NETIF_F_RXHASH)) - en_warn(priv, - "Toeplitz hash function should be used in conjunction with RX hashing for optimal performance\n"); - if (hfunc == ETH_RSS_HASH_XOR && (dev->features & NETIF_F_RXHASH)) - en_warn(priv, - "Enabling both XOR Hash function and RX Hashing can limit RPS functionality\n"); - return 0; + return -EINVAL; } static int mlx4_en_get_rxfh(struct net_device *dev, u32 *ring_index, u8 *key, @@ -1189,6 +1190,8 @@ static int mlx4_en_set_rxfh(struct net_device *dev, const u32 *ring_index, priv->prof->rss_rings = rss_rings; if (key) memcpy(priv->rss_key, key, MLX4_EN_RSS_KEY_SIZE); + if (hfunc != ETH_RSS_HASH_NO_CHANGE) + priv->rss_hash_fn = hfunc; if (port_up) { err = mlx4_en_start_port(dev); diff --git a/drivers/net/ethernet/myricom/myri10ge/myri10ge.c b/drivers/net/ethernet/myricom/myri10ge/myri10ge.c index 1412f5af05ec..2bae50292dcd 100644 --- a/drivers/net/ethernet/myricom/myri10ge/myri10ge.c +++ b/drivers/net/ethernet/myricom/myri10ge/myri10ge.c @@ -69,11 +69,7 @@ #include <net/ip.h> #include <net/tcp.h> #include <asm/byteorder.h> -#include <asm/io.h> #include <asm/processor.h> -#ifdef CONFIG_MTRR -#include <asm/mtrr.h> -#endif #include <net/busy_poll.h> #include "myri10ge_mcp.h" @@ -242,8 +238,7 @@ struct myri10ge_priv { unsigned int rdma_tags_available; int intr_coal_delay; __be32 __iomem *intr_coal_delay_ptr; - int mtrr; - int wc_enabled; + int wc_cookie; int down_cnt; wait_queue_head_t down_wq; struct work_struct watchdog_work; @@ -1905,7 +1900,7 @@ static const char myri10ge_gstrings_main_stats[][ETH_GSTRING_LEN] = { "tx_aborted_errors", "tx_carrier_errors", "tx_fifo_errors", "tx_heartbeat_errors", "tx_window_errors", /* device-specific stats */ - "tx_boundary", "WC", "irq", "MSI", "MSIX", + "tx_boundary", "irq", "MSI", "MSIX", "read_dma_bw_MBs", "write_dma_bw_MBs", "read_write_dma_bw_MBs", "serial_number", "watchdog_resets", #ifdef CONFIG_MYRI10GE_DCA @@ -1984,7 +1979,6 @@ myri10ge_get_ethtool_stats(struct net_device *netdev, data[i] = ((u64 *)&link_stats)[i]; data[i++] = (unsigned int)mgp->tx_boundary; - data[i++] = (unsigned int)mgp->wc_enabled; data[i++] = (unsigned int)mgp->pdev->irq; data[i++] = (unsigned int)mgp->msi_enabled; data[i++] = (unsigned int)mgp->msix_enabled; @@ -4040,14 +4034,7 @@ static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent) mgp->board_span = pci_resource_len(pdev, 0); mgp->iomem_base = pci_resource_start(pdev, 0); - mgp->mtrr = -1; - mgp->wc_enabled = 0; -#ifdef CONFIG_MTRR - mgp->mtrr = mtrr_add(mgp->iomem_base, mgp->board_span, - MTRR_TYPE_WRCOMB, 1); - if (mgp->mtrr >= 0) - mgp->wc_enabled = 1; -#endif + mgp->wc_cookie = arch_phys_wc_add(mgp->iomem_base, mgp->board_span); mgp->sram = ioremap_wc(mgp->iomem_base, mgp->board_span); if (mgp->sram == NULL) { dev_err(&pdev->dev, "ioremap failed for %ld bytes at 0x%lx\n", @@ -4146,14 +4133,14 @@ static int myri10ge_probe(struct pci_dev *pdev, const struct pci_device_id *ent) goto abort_with_state; } if (mgp->msix_enabled) - dev_info(dev, "%d MSI-X IRQs, tx bndry %d, fw %s, WC %s\n", + dev_info(dev, "%d MSI-X IRQs, tx bndry %d, fw %s, MTRR %s, WC Enabled\n", mgp->num_slices, mgp->tx_boundary, mgp->fw_name, - (mgp->wc_enabled ? "Enabled" : "Disabled")); + (mgp->wc_cookie > 0 ? "Enabled" : "Disabled")); else - dev_info(dev, "%s IRQ %d, tx bndry %d, fw %s, WC %s\n", + dev_info(dev, "%s IRQ %d, tx bndry %d, fw %s, MTRR %s, WC Enabled\n", mgp->msi_enabled ? "MSI" : "xPIC", pdev->irq, mgp->tx_boundary, mgp->fw_name, - (mgp->wc_enabled ? "Enabled" : "Disabled")); + (mgp->wc_cookie > 0 ? "Enabled" : "Disabled")); board_number++; return 0; @@ -4175,10 +4162,7 @@ abort_with_ioremap: iounmap(mgp->sram); abort_with_mtrr: -#ifdef CONFIG_MTRR - if (mgp->mtrr >= 0) - mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span); -#endif + arch_phys_wc_del(mgp->wc_cookie); dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd), mgp->cmd, mgp->cmd_bus); @@ -4220,11 +4204,7 @@ static void myri10ge_remove(struct pci_dev *pdev) pci_restore_state(pdev); iounmap(mgp->sram); - -#ifdef CONFIG_MTRR - if (mgp->mtrr >= 0) - mtrr_del(mgp->mtrr, mgp->iomem_base, mgp->board_span); -#endif + arch_phys_wc_del(mgp->wc_cookie); myri10ge_free_slices(mgp); kfree(mgp->msix_vectors); dma_free_coherent(&pdev->dev, sizeof(*mgp->cmd), diff --git a/drivers/net/phy/mdio-gpio.c b/drivers/net/phy/mdio-gpio.c index 49ce7ece5af3..c9cb486c753d 100644 --- a/drivers/net/phy/mdio-gpio.c +++ b/drivers/net/phy/mdio-gpio.c @@ -80,7 +80,8 @@ static void mdio_dir(struct mdiobb_ctrl *ctrl, int dir) * assume the pin serves as pull-up. If direction is * output, the default value is high. */ - gpio_set_value(bitbang->mdo, 1 ^ bitbang->mdo_active_low); + gpio_set_value_cansleep(bitbang->mdo, + 1 ^ bitbang->mdo_active_low); return; } @@ -96,7 +97,8 @@ static int mdio_get(struct mdiobb_ctrl *ctrl) struct mdio_gpio_info *bitbang = container_of(ctrl, struct mdio_gpio_info, ctrl); - return gpio_get_value(bitbang->mdio) ^ bitbang->mdio_active_low; + return gpio_get_value_cansleep(bitbang->mdio) ^ + bitbang->mdio_active_low; } static void mdio_set(struct mdiobb_ctrl *ctrl, int what) @@ -105,9 +107,11 @@ static void mdio_set(struct mdiobb_ctrl *ctrl, int what) container_of(ctrl, struct mdio_gpio_info, ctrl); if (bitbang->mdo) - gpio_set_value(bitbang->mdo, what ^ bitbang->mdo_active_low); + gpio_set_value_cansleep(bitbang->mdo, + what ^ bitbang->mdo_active_low); else - gpio_set_value(bitbang->mdio, what ^ bitbang->mdio_active_low); + gpio_set_value_cansleep(bitbang->mdio, + what ^ bitbang->mdio_active_low); } static void mdc_set(struct mdiobb_ctrl *ctrl, int what) @@ -115,7 +119,7 @@ static void mdc_set(struct mdiobb_ctrl *ctrl, int what) struct mdio_gpio_info *bitbang = container_of(ctrl, struct mdio_gpio_info, ctrl); - gpio_set_value(bitbang->mdc, what ^ bitbang->mdc_active_low); + gpio_set_value_cansleep(bitbang->mdc, what ^ bitbang->mdc_active_low); } static struct mdiobb_ops mdio_gpio_ops = { diff --git a/drivers/net/phy/mdio-mux-gpio.c b/drivers/net/phy/mdio-mux-gpio.c index 1a87a585e74d..66edd99bc302 100644 --- a/drivers/net/phy/mdio-mux-gpio.c +++ b/drivers/net/phy/mdio-mux-gpio.c @@ -12,33 +12,30 @@ #include <linux/module.h> #include <linux/phy.h> #include <linux/mdio-mux.h> -#include <linux/of_gpio.h> +#include <linux/gpio/consumer.h> #define DRV_VERSION "1.1" #define DRV_DESCRIPTION "GPIO controlled MDIO bus multiplexer driver" -#define MDIO_MUX_GPIO_MAX_BITS 8 - struct mdio_mux_gpio_state { - struct gpio_desc *gpio[MDIO_MUX_GPIO_MAX_BITS]; - unsigned int num_gpios; + struct gpio_descs *gpios; void *mux_handle; }; static int mdio_mux_gpio_switch_fn(int current_child, int desired_child, void *data) { - int values[MDIO_MUX_GPIO_MAX_BITS]; - unsigned int n; struct mdio_mux_gpio_state *s = data; + int values[s->gpios->ndescs]; + unsigned int n; if (current_child == desired_child) return 0; - for (n = 0; n < s->num_gpios; n++) { + for (n = 0; n < s->gpios->ndescs; n++) values[n] = (desired_child >> n) & 1; - } - gpiod_set_array_cansleep(s->num_gpios, s->gpio, values); + + gpiod_set_array_cansleep(s->gpios->ndescs, s->gpios->desc, values); return 0; } @@ -46,56 +43,33 @@ static int mdio_mux_gpio_switch_fn(int current_child, int desired_child, static int mdio_mux_gpio_probe(struct platform_device *pdev) { struct mdio_mux_gpio_state *s; - int num_gpios; - unsigned int n; int r; - if (!pdev->dev.of_node) - return -ENODEV; - - num_gpios = of_gpio_count(pdev->dev.of_node); - if (num_gpios <= 0 || num_gpios > MDIO_MUX_GPIO_MAX_BITS) - return -ENODEV; - s = devm_kzalloc(&pdev->dev, sizeof(*s), GFP_KERNEL); if (!s) return -ENOMEM; - s->num_gpios = num_gpios; - - for (n = 0; n < num_gpios; ) { - struct gpio_desc *gpio = gpiod_get_index(&pdev->dev, NULL, n, - GPIOD_OUT_LOW); - if (IS_ERR(gpio)) { - r = PTR_ERR(gpio); - goto err; - } - s->gpio[n] = gpio; - n++; - } + s->gpios = gpiod_get_array(&pdev->dev, NULL, GPIOD_OUT_LOW); + if (IS_ERR(s->gpios)) + return PTR_ERR(s->gpios); r = mdio_mux_init(&pdev->dev, mdio_mux_gpio_switch_fn, &s->mux_handle, s); - if (r == 0) { - pdev->dev.platform_data = s; - return 0; - } -err: - while (n) { - n--; - gpiod_put(s->gpio[n]); + if (r != 0) { + gpiod_put_array(s->gpios); + return r; } - return r; + + pdev->dev.platform_data = s; + return 0; } static int mdio_mux_gpio_remove(struct platform_device *pdev) { - unsigned int n; struct mdio_mux_gpio_state *s = dev_get_platdata(&pdev->dev); mdio_mux_uninit(s->mux_handle); - for (n = 0; n < s->num_gpios; n++) - gpiod_put(s->gpio[n]); + gpiod_put_array(s->gpios); return 0; } diff --git a/drivers/net/ppp/ppp_mppe.c b/drivers/net/ppp/ppp_mppe.c index 911b21602ff2..05005c660d4d 100644 --- a/drivers/net/ppp/ppp_mppe.c +++ b/drivers/net/ppp/ppp_mppe.c @@ -478,7 +478,6 @@ mppe_decompress(void *arg, unsigned char *ibuf, int isize, unsigned char *obuf, struct blkcipher_desc desc = { .tfm = state->arc4 }; unsigned ccount; int flushed = MPPE_BITS(ibuf) & MPPE_BIT_FLUSHED; - int sanity = 0; struct scatterlist sg_in[1], sg_out[1]; if (isize <= PPP_HDRLEN + MPPE_OVHD) { @@ -514,31 +513,19 @@ mppe_decompress(void *arg, unsigned char *ibuf, int isize, unsigned char *obuf, "mppe_decompress[%d]: ENCRYPTED bit not set!\n", state->unit); state->sanity_errors += 100; - sanity = 1; + goto sanity_error; } if (!state->stateful && !flushed) { printk(KERN_DEBUG "mppe_decompress[%d]: FLUSHED bit not set in " "stateless mode!\n", state->unit); state->sanity_errors += 100; - sanity = 1; + goto sanity_error; } if (state->stateful && ((ccount & 0xff) == 0xff) && !flushed) { printk(KERN_DEBUG "mppe_decompress[%d]: FLUSHED bit not set on " "flag packet!\n", state->unit); state->sanity_errors += 100; - sanity = 1; - } - - if (sanity) { - if (state->sanity_errors < SANITY_MAX) - return DECOMP_ERROR; - else - /* - * Take LCP down if the peer is sending too many bogons. - * We don't want to do this for a single or just a few - * instances since it could just be due to packet corruption. - */ - return DECOMP_FATALERROR; + goto sanity_error; } /* @@ -546,6 +533,13 @@ mppe_decompress(void *arg, unsigned char *ibuf, int isize, unsigned char *obuf, */ if (!state->stateful) { + /* Discard late packet */ + if ((ccount - state->ccount) % MPPE_CCOUNT_SPACE + > MPPE_CCOUNT_SPACE / 2) { + state->sanity_errors++; + goto sanity_error; + } + /* RFC 3078, sec 8.1. Rekey for every packet. */ while (state->ccount != ccount) { mppe_rekey(state, 0); @@ -649,6 +643,16 @@ mppe_decompress(void *arg, unsigned char *ibuf, int isize, unsigned char *obuf, state->sanity_errors >>= 1; return osize; + +sanity_error: + if (state->sanity_errors < SANITY_MAX) + return DECOMP_ERROR; + else + /* Take LCP down if the peer is sending too many bogons. + * We don't want to do this for a single or just a few + * instances since it could just be due to packet corruption. + */ + return DECOMP_FATALERROR; } /* diff --git a/drivers/net/vxlan.c b/drivers/net/vxlan.c index 154116aafd0d..27a5f954f8e9 100644 --- a/drivers/net/vxlan.c +++ b/drivers/net/vxlan.c @@ -730,12 +730,8 @@ static int vxlan_fdb_create(struct vxlan_dev *vxlan, /* Only change unicasts */ if (!(is_multicast_ether_addr(f->eth_addr) || is_zero_ether_addr(f->eth_addr))) { - int rc = vxlan_fdb_replace(f, ip, port, vni, + notify |= vxlan_fdb_replace(f, ip, port, vni, ifindex); - - if (rc < 0) - return rc; - notify |= rc; } else return -EOPNOTSUPP; } diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c index c43aca69fb30..0fc3fe5fd5b8 100644 --- a/drivers/s390/char/con3215.c +++ b/drivers/s390/char/con3215.c @@ -667,6 +667,8 @@ static struct raw3215_info *raw3215_alloc_info(void) info->buffer = kzalloc(RAW3215_BUFFER_SIZE, GFP_KERNEL | GFP_DMA); info->inbuf = kzalloc(RAW3215_INBUF_SIZE, GFP_KERNEL | GFP_DMA); if (!info->buffer || !info->inbuf) { + kfree(info->inbuf); + kfree(info->buffer); kfree(info); return NULL; } diff --git a/drivers/sh/pm_runtime.c b/drivers/sh/pm_runtime.c index cd4c293f0dd0..fe8875f0d7be 100644 --- a/drivers/sh/pm_runtime.c +++ b/drivers/sh/pm_runtime.c @@ -80,9 +80,10 @@ static int __init sh_pm_runtime_init(void) if (IS_ENABLED(CONFIG_ARCH_SHMOBILE_MULTI)) { if (!of_machine_is_compatible("renesas,emev2") && !of_machine_is_compatible("renesas,r7s72100") && - !of_machine_is_compatible("renesas,r8a73a4") && #ifndef CONFIG_PM_GENERIC_DOMAINS_OF + !of_machine_is_compatible("renesas,r8a73a4") && !of_machine_is_compatible("renesas,r8a7740") && + !of_machine_is_compatible("renesas,sh73a0") && #endif !of_machine_is_compatible("renesas,r8a7778") && !of_machine_is_compatible("renesas,r8a7779") && @@ -90,9 +91,7 @@ static int __init sh_pm_runtime_init(void) !of_machine_is_compatible("renesas,r8a7791") && !of_machine_is_compatible("renesas,r8a7792") && !of_machine_is_compatible("renesas,r8a7793") && - !of_machine_is_compatible("renesas,r8a7794") && - !of_machine_is_compatible("renesas,sh7372") && - !of_machine_is_compatible("renesas,sh73a0")) + !of_machine_is_compatible("renesas,r8a7794")) return 0; } diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 08da4d3e2162..46bcebba54b2 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1998,6 +1998,8 @@ pci_wch_ch38x_setup(struct serial_private *priv, #define PCIE_DEVICE_ID_WCH_CH382_2S1P 0x3250 #define PCIE_DEVICE_ID_WCH_CH384_4S 0x3470 +#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358 + /* Unknown vendors/cards - this should not be in linux/pci_ids.h */ #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584 #define PCI_SUBDEVICE_ID_UNKNOWN_0x1588 0x1588 @@ -2520,6 +2522,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { .subdevice = PCI_ANY_ID, .setup = pci_xr17v35x_setup, }, + { + .vendor = PCI_VENDOR_ID_EXAR, + .device = PCI_DEVICE_ID_EXAR_XR17V8358, + .subvendor = PCI_ANY_ID, + .subdevice = PCI_ANY_ID, + .setup = pci_xr17v35x_setup, + }, /* * Xircom cards */ @@ -2999,6 +3008,7 @@ enum pci_board_num_t { pbn_exar_XR17V352, pbn_exar_XR17V354, pbn_exar_XR17V358, + pbn_exar_XR17V8358, pbn_exar_ibm_saturn, pbn_pasemi_1682M, pbn_ni8430_2, @@ -3685,6 +3695,14 @@ static struct pciserial_board pci_boards[] = { .reg_shift = 0, .first_offset = 0, }, + [pbn_exar_XR17V8358] = { + .flags = FL_BASE0, + .num_ports = 16, + .base_baud = 7812500, + .uart_offset = 0x400, + .reg_shift = 0, + .first_offset = 0, + }, [pbn_exar_ibm_saturn] = { .flags = FL_BASE0, .num_ports = 1, @@ -5080,7 +5098,7 @@ static struct pci_device_id serial_pci_tbl[] = { 0, 0, pbn_exar_XR17C158 }, /* - * Exar Corp. XR17V35[248] Dual/Quad/Octal PCIe UARTs + * Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs */ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352, PCI_ANY_ID, PCI_ANY_ID, @@ -5094,7 +5112,10 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_exar_XR17V358 }, - + { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358, + PCI_ANY_ID, PCI_ANY_ID, + 0, + 0, pbn_exar_XR17V8358 }, /* * Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke) */ diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index d58fe4763d9e..27dade29646b 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -880,6 +880,7 @@ static int atmel_prepare_tx_dma(struct uart_port *port) config.direction = DMA_MEM_TO_DEV; config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; config.dst_addr = port->mapbase + ATMEL_US_THR; + config.dst_maxburst = 1; ret = dmaengine_slave_config(atmel_port->chan_tx, &config); @@ -1059,6 +1060,7 @@ static int atmel_prepare_rx_dma(struct uart_port *port) config.direction = DMA_DEV_TO_MEM; config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; config.src_addr = port->mapbase + ATMEL_US_RHR; + config.src_maxburst = 1; ret = dmaengine_slave_config(atmel_port->chan_rx, &config); diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 5b73afb9f9f3..137381e649e5 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -346,7 +346,6 @@ static const struct of_device_id of_platform_serial_table[] = { { .compatible = "ibm,qpace-nwp-serial", .data = (void *)PORT_NWPSERIAL, }, #endif - { .type = "serial", .data = (void *)PORT_UNKNOWN, }, { /* end of list */ }, }; diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c index cf08876922f1..a0ae942d9562 100644 --- a/drivers/tty/serial/samsung.c +++ b/drivers/tty/serial/samsung.c @@ -1068,8 +1068,9 @@ static int s3c64xx_serial_startup(struct uart_port *port) spin_lock_irqsave(&port->lock, flags); ufcon = rd_regl(port, S3C2410_UFCON); - ufcon |= S3C2410_UFCON_RESETRX | S3C2410_UFCON_RESETTX | - S5PV210_UFCON_RXTRIG8; + ufcon |= S3C2410_UFCON_RESETRX | S5PV210_UFCON_RXTRIG8; + if (!uart_console(port)) + ufcon |= S3C2410_UFCON_RESETTX; wr_regl(port, S3C2410_UFCON, ufcon); enable_rx_pio(ourport); diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index eb5b03be9dfd..0b7bb12dfc68 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -1770,7 +1770,7 @@ static const struct file_operations uart_proc_fops = { * @port: the port to write the message * @s: array of characters * @count: number of characters in string to write - * @write: function to write character to port + * @putchar: function to write character to port */ void uart_console_write(struct uart_port *port, const char *s, unsigned int count, diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c index 708eead850b0..b1c6bd3d483f 100644 --- a/drivers/tty/serial/uartlite.c +++ b/drivers/tty/serial/uartlite.c @@ -632,7 +632,8 @@ MODULE_DEVICE_TABLE(of, ulite_of_match); static int ulite_probe(struct platform_device *pdev) { - struct resource *res, *res2; + struct resource *res; + int irq; int id = pdev->id; #ifdef CONFIG_OF const __be32 *prop; @@ -646,11 +647,11 @@ static int ulite_probe(struct platform_device *pdev) if (!res) return -ENODEV; - res2 = platform_get_resource(pdev, IORESOURCE_IRQ, 0); - if (!res2) - return -ENODEV; + irq = platform_get_irq(pdev, 0); + if (irq <= 0) + return -ENXIO; - return ulite_assign(&pdev->dev, id, res->start, res2->start); + return ulite_assign(&pdev->dev, id, res->start, irq); } static int ulite_remove(struct platform_device *pdev) diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c index f218ec658f5d..3ddbac767db3 100644 --- a/drivers/tty/serial/xilinx_uartps.c +++ b/drivers/tty/serial/xilinx_uartps.c @@ -1331,9 +1331,9 @@ static SIMPLE_DEV_PM_OPS(cdns_uart_dev_pm_ops, cdns_uart_suspend, */ static int cdns_uart_probe(struct platform_device *pdev) { - int rc, id; + int rc, id, irq; struct uart_port *port; - struct resource *res, *res2; + struct resource *res; struct cdns_uart *cdns_uart_data; cdns_uart_data = devm_kzalloc(&pdev->dev, sizeof(*cdns_uart_data), @@ -1380,9 +1380,9 @@ static int cdns_uart_probe(struct platform_device *pdev) goto err_out_clk_disable; } - res2 = platform_get_resource(pdev, IORESOURCE_IRQ, 0); - if (!res2) { - rc = -ENODEV; + irq = platform_get_irq(pdev, 0); + if (irq <= 0) { + rc = -ENXIO; goto err_out_clk_disable; } @@ -1411,7 +1411,7 @@ static int cdns_uart_probe(struct platform_device *pdev) * and triggers invocation of the config_port() entry point. */ port->mapbase = res->start; - port->irq = res2->start; + port->irq = irq; port->dev = &pdev->dev; port->uartclk = clk_get_rate(cdns_uart_data->uartclk); port->private_data = cdns_uart_data; diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c index 632fc8152061..8e53fe469664 100644 --- a/drivers/tty/tty_ioctl.c +++ b/drivers/tty/tty_ioctl.c @@ -536,7 +536,7 @@ EXPORT_SYMBOL(tty_termios_hw_change); * Locking: termios_rwsem */ -static int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) +int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) { struct ktermios old_termios; struct tty_ldisc *ld; @@ -569,6 +569,7 @@ static int tty_set_termios(struct tty_struct *tty, struct ktermios *new_termios) up_write(&tty->termios_rwsem); return 0; } +EXPORT_SYMBOL_GPL(tty_set_termios); /** * set_termios - set termios values for a tty diff --git a/drivers/usb/chipidea/otg_fsm.c b/drivers/usb/chipidea/otg_fsm.c index 083acf45ad5a..19d655a743b5 100644 --- a/drivers/usb/chipidea/otg_fsm.c +++ b/drivers/usb/chipidea/otg_fsm.c @@ -520,7 +520,6 @@ static int ci_otg_start_host(struct otg_fsm *fsm, int on) { struct ci_hdrc *ci = container_of(fsm, struct ci_hdrc, fsm); - mutex_unlock(&fsm->lock); if (on) { ci_role_stop(ci); ci_role_start(ci, CI_ROLE_HOST); @@ -529,7 +528,6 @@ static int ci_otg_start_host(struct otg_fsm *fsm, int on) hw_device_reset(ci); ci_role_start(ci, CI_ROLE_GADGET); } - mutex_lock(&fsm->lock); return 0; } @@ -537,12 +535,10 @@ static int ci_otg_start_gadget(struct otg_fsm *fsm, int on) { struct ci_hdrc *ci = container_of(fsm, struct ci_hdrc, fsm); - mutex_unlock(&fsm->lock); if (on) usb_gadget_vbus_connect(&ci->gadget); else usb_gadget_vbus_disconnect(&ci->gadget); - mutex_lock(&fsm->lock); return 0; } diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 3e15add665e2..5c8f58114677 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -1142,11 +1142,16 @@ static int acm_probe(struct usb_interface *intf, } while (buflen > 0) { + elength = buffer[0]; + if (!elength) { + dev_err(&intf->dev, "skipping garbage byte\n"); + elength = 1; + goto next_desc; + } if (buffer[1] != USB_DT_CS_INTERFACE) { dev_err(&intf->dev, "skipping garbage\n"); goto next_desc; } - elength = buffer[0]; switch (buffer[2]) { case USB_CDC_UNION_TYPE: /* we've found it */ diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c index 9db74ca7e5b9..275c92e53a59 100644 --- a/drivers/usb/host/ehci-msm.c +++ b/drivers/usb/host/ehci-msm.c @@ -88,13 +88,20 @@ static int ehci_msm_probe(struct platform_device *pdev) } res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - hcd->regs = devm_ioremap_resource(&pdev->dev, res); - if (IS_ERR(hcd->regs)) { - ret = PTR_ERR(hcd->regs); + if (!res) { + dev_err(&pdev->dev, "Unable to get memory resource\n"); + ret = -ENODEV; goto put_hcd; } + hcd->rsrc_start = res->start; hcd->rsrc_len = resource_size(res); + hcd->regs = devm_ioremap(&pdev->dev, hcd->rsrc_start, hcd->rsrc_len); + if (!hcd->regs) { + dev_err(&pdev->dev, "ioremap failed\n"); + ret = -ENOMEM; + goto put_hcd; + } /* * OTG driver takes care of PHY initialization, clock management, diff --git a/drivers/usb/storage/uas-detect.h b/drivers/usb/storage/uas-detect.h index 9893d696fc97..f58caa9e6a27 100644 --- a/drivers/usb/storage/uas-detect.h +++ b/drivers/usb/storage/uas-detect.h @@ -51,7 +51,8 @@ static int uas_find_endpoints(struct usb_host_interface *alt, } static int uas_use_uas_driver(struct usb_interface *intf, - const struct usb_device_id *id) + const struct usb_device_id *id, + unsigned long *flags_ret) { struct usb_host_endpoint *eps[4] = { }; struct usb_device *udev = interface_to_usbdev(intf); @@ -73,7 +74,7 @@ static int uas_use_uas_driver(struct usb_interface *intf, * this writing the following versions exist: * ASM1051 - no uas support version * ASM1051 - with broken (*) uas support - * ASM1053 - with working uas support + * ASM1053 - with working uas support, but problems with large xfers * ASM1153 - with working uas support * * Devices with these chips re-use a number of device-ids over the @@ -103,6 +104,9 @@ static int uas_use_uas_driver(struct usb_interface *intf, } else if (usb_ss_max_streams(&eps[1]->ss_ep_comp) == 32) { /* Possibly an ASM1051, disable uas */ flags |= US_FL_IGNORE_UAS; + } else { + /* ASM1053, these have issues with large transfers */ + flags |= US_FL_MAX_SECTORS_240; } } @@ -132,5 +136,8 @@ static int uas_use_uas_driver(struct usb_interface *intf, return 0; } + if (flags_ret) + *flags_ret = flags; + return 1; } diff --git a/drivers/usb/storage/uas.c b/drivers/usb/storage/uas.c index 6cdabdc119a7..6d3122afeed3 100644 --- a/drivers/usb/storage/uas.c +++ b/drivers/usb/storage/uas.c @@ -759,7 +759,10 @@ static int uas_eh_bus_reset_handler(struct scsi_cmnd *cmnd) static int uas_slave_alloc(struct scsi_device *sdev) { - sdev->hostdata = (void *)sdev->host->hostdata; + struct uas_dev_info *devinfo = + (struct uas_dev_info *)sdev->host->hostdata; + + sdev->hostdata = devinfo; /* USB has unusual DMA-alignment requirements: Although the * starting address of each scatter-gather element doesn't matter, @@ -778,6 +781,11 @@ static int uas_slave_alloc(struct scsi_device *sdev) */ blk_queue_update_dma_alignment(sdev->request_queue, (512 - 1)); + if (devinfo->flags & US_FL_MAX_SECTORS_64) + blk_queue_max_hw_sectors(sdev->request_queue, 64); + else if (devinfo->flags & US_FL_MAX_SECTORS_240) + blk_queue_max_hw_sectors(sdev->request_queue, 240); + return 0; } @@ -887,8 +895,9 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id) struct Scsi_Host *shost = NULL; struct uas_dev_info *devinfo; struct usb_device *udev = interface_to_usbdev(intf); + unsigned long dev_flags; - if (!uas_use_uas_driver(intf, id)) + if (!uas_use_uas_driver(intf, id, &dev_flags)) return -ENODEV; if (uas_switch_interface(udev, intf)) @@ -910,8 +919,7 @@ static int uas_probe(struct usb_interface *intf, const struct usb_device_id *id) devinfo->udev = udev; devinfo->resetting = 0; devinfo->shutdown = 0; - devinfo->flags = id->driver_info; - usb_stor_adjust_quirks(udev, &devinfo->flags); + devinfo->flags = dev_flags; init_usb_anchor(&devinfo->cmd_urbs); init_usb_anchor(&devinfo->sense_urbs); init_usb_anchor(&devinfo->data_urbs); diff --git a/drivers/usb/storage/usb.c b/drivers/usb/storage/usb.c index 5600c33fcadb..6c10c888f35f 100644 --- a/drivers/usb/storage/usb.c +++ b/drivers/usb/storage/usb.c @@ -479,7 +479,8 @@ void usb_stor_adjust_quirks(struct usb_device *udev, unsigned long *fflags) US_FL_SINGLE_LUN | US_FL_NO_WP_DETECT | US_FL_NO_READ_DISC_INFO | US_FL_NO_READ_CAPACITY_16 | US_FL_INITIAL_READ10 | US_FL_WRITE_CACHE | - US_FL_NO_ATA_1X | US_FL_NO_REPORT_OPCODES); + US_FL_NO_ATA_1X | US_FL_NO_REPORT_OPCODES | + US_FL_MAX_SECTORS_240); p = quirks; while (*p) { @@ -520,6 +521,9 @@ void usb_stor_adjust_quirks(struct usb_device *udev, unsigned long *fflags) case 'f': f |= US_FL_NO_REPORT_OPCODES; break; + case 'g': + f |= US_FL_MAX_SECTORS_240; + break; case 'h': f |= US_FL_CAPACITY_HEURISTICS; break; @@ -1080,7 +1084,7 @@ static int storage_probe(struct usb_interface *intf, /* If uas is enabled and this device can do uas then ignore it. */ #if IS_ENABLED(CONFIG_USB_UAS) - if (uas_use_uas_driver(intf, id)) + if (uas_use_uas_driver(intf, id, NULL)) return -ENXIO; #endif |