diff options
Diffstat (limited to 'include/linux/nl80211.h')
| -rw-r--r-- | include/linux/nl80211.h | 578 |
1 files changed, 557 insertions, 21 deletions
diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index 0edb2566c14c..c7ccaae15af6 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -77,6 +77,39 @@ */ /** + * DOC: Virtual interface / concurrency capabilities + * + * Some devices are able to operate with virtual MACs, they can have + * more than one virtual interface. The capability handling for this + * is a bit complex though, as there may be a number of restrictions + * on the types of concurrency that are supported. + * + * To start with, each device supports the interface types listed in + * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the + * types there no concurrency is implied. + * + * Once concurrency is desired, more attributes must be observed: + * To start with, since some interface types are purely managed in + * software, like the AP-VLAN type in mac80211 for example, there's + * an additional list of these, they can be added at any time and + * are only restricted by some semantic restrictions (e.g. AP-VLAN + * cannot be added without a corresponding AP interface). This list + * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute. + * + * Further, the list of supported combinations is exported. This is + * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically, + * it exports a list of "groups", and at any point in time the + * interfaces that are currently active must fall into any one of + * the advertised groups. Within each group, there are restrictions + * on the number of interfaces of different types that are supported + * and also the number of different channels, along with potentially + * some other restrictions. See &enum nl80211_if_combination_attrs. + * + * All together, these attributes define the concurrency of virtual + * interfaces that a given device supports. + */ + +/** * enum nl80211_commands - supported nl80211 commands * * @NL80211_CMD_UNSPEC: unspecified command to catch errors @@ -148,6 +181,10 @@ * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to * destination %NL80211_ATTR_MAC on the interface identified by * %NL80211_ATTR_IFINDEX. + * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by + * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP. + * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by + * %NL80211_ATTR_MAC. * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the * the interface identified by %NL80211_ATTR_IFINDEX. * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC @@ -172,10 +209,10 @@ * to the specified ISO/IEC 3166-1 alpha2 country code. The core will * store this as a valid request and then query userspace for it. * - * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the + * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * - * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the + * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the * interface identified by %NL80211_ATTR_IFINDEX * * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The @@ -199,6 +236,28 @@ * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons, * partial scan results may be available * + * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain + * intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL. + * Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS) + * are passed, they are used in the probe requests. For + * broadcast, a broadcast SSID must be passed (ie. an empty + * string). If no SSID is passed, no probe requests are sent and + * a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES, + * if passed, define which channels should be scanned; if not + * passed, all channels allowed for the current regulatory domain + * are used. Extra IEs can also be passed from the userspace by + * using the %NL80211_ATTR_IE attribute. + * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan + * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan + * results available. + * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has + * stopped. The driver may issue this event at any time during a + * scheduled scan. One reason for stopping the scan is if the hardware + * does not support starting an association or a normal scan while running + * a scheduled scan. This event is also sent when the + * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface + * is brought down while a scheduled scan was running. + * * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation * or noise level * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to @@ -358,11 +417,16 @@ * user space application). %NL80211_ATTR_FRAME is used to specify the * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on - * which channel the frame is to be transmitted or was received. This - * channel has to be the current channel (remain-on-channel or the - * operational channel). When called, this operation returns a cookie - * (%NL80211_ATTR_COOKIE) that will be included with the TX status event - * pertaining to the TX request. + * which channel the frame is to be transmitted or was received. If this + * channel is not the current channel (remain-on-channel or the + * operational channel) the device will switch to the given channel and + * transmit the frame, optionally waiting for a response for the time + * specified using %NL80211_ATTR_DURATION. When called, this operation + * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the + * TX status event pertaining to the TX request. + * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this + * command may be used with the corresponding cookie to cancel the wait + * time if it is known that it is no longer necessary. * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility. * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies @@ -389,11 +453,41 @@ * * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. * + * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial + * mesh config parameters may be given. + * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the + * network is determined by the network interface. + * + * @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame + * notification. This event is used to indicate that an unprotected + * deauthentication frame was dropped when MFP is in use. + * @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame + * notification. This event is used to indicate that an unprotected + * disassociation frame was dropped when MFP is in use. + * + * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a + * beacon or probe response from a compatible mesh peer. This is only + * sent while no station information (sta_info) exists for the new peer + * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On + * reception of this notification, userspace may decide to create a new + * station (@NL80211_CMD_NEW_STATION). To stop this notification from + * reoccurring, the userspace authentication daemon may want to create the + * new station with the AUTHENTICATED flag unset and maybe change it later + * depending on the authentication result. + * + * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings. + * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings. + * Since wireless is more complex than wired ethernet, it supports + * various triggers. These triggers can be configured through this + * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For + * more background information, see + * http://wireless.kernel.org/en/users/Documentation/WoWLAN. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ enum nl80211_commands { -/* don't change the order or add anything inbetween, this is ABI! */ +/* don't change the order or add anything between, this is ABI! */ NL80211_CMD_UNSPEC, NL80211_CMD_GET_WIPHY, /* can dump */ @@ -431,8 +525,8 @@ enum nl80211_commands { NL80211_CMD_SET_REG, NL80211_CMD_REQ_SET_REG, - NL80211_CMD_GET_MESH_PARAMS, - NL80211_CMD_SET_MESH_PARAMS, + NL80211_CMD_GET_MESH_CONFIG, + NL80211_CMD_SET_MESH_CONFIG, NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */, @@ -493,6 +587,24 @@ enum nl80211_commands { NL80211_CMD_SET_CHANNEL, NL80211_CMD_SET_WDS_PEER, + NL80211_CMD_FRAME_WAIT_CANCEL, + + NL80211_CMD_JOIN_MESH, + NL80211_CMD_LEAVE_MESH, + + NL80211_CMD_UNPROT_DEAUTHENTICATE, + NL80211_CMD_UNPROT_DISASSOCIATE, + + NL80211_CMD_NEW_PEER_CANDIDATE, + + NL80211_CMD_GET_WOWLAN, + NL80211_CMD_SET_WOWLAN, + + NL80211_CMD_START_SCHED_SCAN, + NL80211_CMD_STOP_SCHED_SCAN, + NL80211_CMD_SCHED_SCAN_RESULTS, + NL80211_CMD_SCHED_SCAN_STOPPED, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -513,6 +625,11 @@ enum nl80211_commands { #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT +/* source-level API compatibility */ +#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG +#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG +#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE + /** * enum nl80211_attrs - nl80211 netlink attributes * @@ -583,7 +700,7 @@ enum nl80211_commands { * consisting of a nested array. * * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes). - * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link. + * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link. * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path. * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path * info given for %NL80211_CMD_GET_MPATH, nested attribute described at @@ -758,6 +875,9 @@ enum nl80211_commands { * cache, a wiphy attribute. * * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32. + * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that + * specifies the maximum duration that can be requested with the + * remain-on-channel operation, in milliseconds, u32. * * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects. * @@ -804,11 +924,83 @@ enum nl80211_commands { * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly * means support for per-station GTKs. * + * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting. + * This can be used to mask out antennas which are not attached or should + * not be used for transmitting. If an antenna is not selected in this + * bitmap the hardware is not allowed to transmit on this antenna. + * + * Each bit represents one antenna, starting with antenna 1 at the first + * bit. Depending on which antennas are selected in the bitmap, 802.11n + * drivers can derive which chainmasks to use (if all antennas belonging to + * a particular chain are disabled this chain should be disabled) and if + * a chain has diversity antennas wether diversity should be used or not. + * HT capabilities (STBC, TX Beamforming, Antenna selection) can be + * derived from the available chains after applying the antenna mask. + * Non-802.11n drivers can derive wether to use diversity or not. + * Drivers may reject configurations or RX/TX mask combinations they cannot + * support by returning -EINVAL. + * + * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving. + * This can be used to mask out antennas which are not attached or should + * not be used for receiving. If an antenna is not selected in this bitmap + * the hardware should not be configured to receive on this antenna. + * For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX. + * + * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available + * for configuration as TX antennas via the above parameters. + * + * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available + * for configuration as RX antennas via the above parameters. + * + * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS + * + * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be + * transmitted on another channel when the channel given doesn't match + * the current channel. If the current channel doesn't match and this + * flag isn't set, the frame will be rejected. This is also used as an + * nl80211 capability flag. + * + * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16) + * + * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags + * attributes, specifying what a key should be set as default as. + * See &enum nl80211_key_default_types. + * + * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be + * changed once the mesh is active. + * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute + * containing attributes from &enum nl80211_meshconf_params. + * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver + * allows auth frames in a mesh to be passed to userspace for processing via + * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag. + * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as + * defined in &enum nl80211_plink_state. Used when userspace is + * driving the peer link management state machine. + * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled. + * + * @NL80211_ATTR_WOWLAN_SUPPORTED: indicates, as part of the wiphy capabilities, + * the supported WoWLAN triggers + * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to + * indicate which WoW triggers should be enabled. This is also + * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN + * triggers. + + * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan + * cycles, in msecs. + * + * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported + * interface combinations. In each nested item, it contains attributes + * defined in &enum nl80211_if_combination_attrs. + * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like + * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that + * are managed in software: interfaces of these types aren't subject to + * any restrictions in their number or combinations. + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ enum nl80211_attrs { -/* don't change the order or add anything inbetween, this is ABI! */ +/* don't change the order or add anything between, this is ABI! */ NL80211_ATTR_UNSPEC, NL80211_ATTR_WIPHY, @@ -858,7 +1050,7 @@ enum nl80211_attrs { NL80211_ATTR_REG_ALPHA2, NL80211_ATTR_REG_RULES, - NL80211_ATTR_MESH_PARAMS, + NL80211_ATTR_MESH_CONFIG, NL80211_ATTR_BSS_BASIC_RATES, @@ -973,6 +1165,35 @@ enum nl80211_attrs { NL80211_ATTR_SUPPORT_IBSS_RSN, + NL80211_ATTR_WIPHY_ANTENNA_TX, + NL80211_ATTR_WIPHY_ANTENNA_RX, + + NL80211_ATTR_MCAST_RATE, + + NL80211_ATTR_OFFCHANNEL_TX_OK, + + NL80211_ATTR_BSS_HT_OPMODE, + + NL80211_ATTR_KEY_DEFAULT_TYPES, + + NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION, + + NL80211_ATTR_MESH_SETUP, + + NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX, + NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX, + + NL80211_ATTR_SUPPORT_MESH_AUTH, + NL80211_ATTR_STA_PLINK_STATE, + + NL80211_ATTR_WOWLAN_TRIGGERS, + NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, + + NL80211_ATTR_SCHED_SCAN_INTERVAL, + + NL80211_ATTR_INTERFACE_COMBINATIONS, + NL80211_ATTR_SOFTWARE_IFTYPES, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -981,6 +1202,7 @@ enum nl80211_attrs { /* source-level API compatibility */ #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION +#define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG /* * Allow user space programs to use #ifdef on new attributes by defining them @@ -1024,7 +1246,9 @@ enum nl80211_attrs { * @NL80211_IFTYPE_ADHOC: independent BSS member * @NL80211_IFTYPE_STATION: managed BSS member * @NL80211_IFTYPE_AP: access point - * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points + * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces + * are a bit special in that they must always be tied to a pre-existing + * AP type interface. * @NL80211_IFTYPE_WDS: wireless distribution interface * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames * @NL80211_IFTYPE_MESH_POINT: mesh point @@ -1066,6 +1290,7 @@ enum nl80211_iftype { * with short barker preamble * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection + * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ @@ -1075,6 +1300,7 @@ enum nl80211_sta_flags { NL80211_STA_FLAG_SHORT_PREAMBLE, NL80211_STA_FLAG_WME, NL80211_STA_FLAG_MFP, + NL80211_STA_FLAG_AUTHENTICATED, /* keep last */ __NL80211_STA_FLAG_AFTER_LAST, @@ -1120,6 +1346,36 @@ enum nl80211_rate_info { }; /** + * enum nl80211_sta_bss_param - BSS information collected by STA + * + * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM + * when getting information about the bitrate of a station. + * + * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved + * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag) + * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled + * (flag) + * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8) + * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16) + * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined + * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use + */ +enum nl80211_sta_bss_param { + __NL80211_STA_BSS_PARAM_INVALID, + NL80211_STA_BSS_PARAM_CTS_PROT, + NL80211_STA_BSS_PARAM_SHORT_PREAMBLE, + NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME, + NL80211_STA_BSS_PARAM_DTIM_PERIOD, + NL80211_STA_BSS_PARAM_BEACON_INTERVAL, + + /* keep last */ + __NL80211_STA_BSS_PARAM_AFTER_LAST, + NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1 +}; + +/** * enum nl80211_sta_info - station information * * These attribute types are used with %NL80211_ATTR_STA_INFO @@ -1129,16 +1385,26 @@ enum nl80211_rate_info { * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs) * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station) * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station) - * @__NL80211_STA_INFO_AFTER_LAST: internal - * @NL80211_STA_INFO_MAX: highest possible station info attribute * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm) * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute - * containing info as possible, see &enum nl80211_sta_info_txrate. + * containing info as possible, see &enum nl80211_rate_info * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station) * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this * station) * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station) * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station) + * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm) + * @NL80211_STA_INFO_LLID: the station's mesh LLID + * @NL80211_STA_INFO_PLID: the station's mesh PLID + * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station + * (see %enum nl80211_plink_state) + * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested + * attribute, like NL80211_STA_INFO_TX_BITRATE. + * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute + * containing info as possible, see &enum nl80211_sta_bss_param + * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected + * @__NL80211_STA_INFO_AFTER_LAST: internal + * @NL80211_STA_INFO_MAX: highest possible station info attribute */ enum nl80211_sta_info { __NL80211_STA_INFO_INVALID, @@ -1154,6 +1420,10 @@ enum nl80211_sta_info { NL80211_STA_INFO_TX_PACKETS, NL80211_STA_INFO_TX_RETRIES, NL80211_STA_INFO_TX_FAILED, + NL80211_STA_INFO_SIGNAL_AVG, + NL80211_STA_INFO_RX_BITRATE, + NL80211_STA_INFO_BSS_PARAM, + NL80211_STA_INFO_CONNECTED_TIME, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -1307,7 +1577,11 @@ enum nl80211_bitrate_attr { * wireless core it thinks its knows the regulatory domain we should be in. * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an * 802.11 country information element with regulatory information it - * thinks we should consider. + * thinks we should consider. cfg80211 only processes the country + * code from the IE, and relies on the regulatory domain information + * structure passed by userspace (CRDA) from our wireless-regdb. + * If a channel is enabled but the country code indicates it should + * be disabled we disable the channel and re-enable it upon disassociation. */ enum nl80211_reg_initiator { NL80211_REGDOM_SET_BY_CORE, @@ -1476,14 +1750,15 @@ enum nl80211_mntr_flags { /** * enum nl80211_meshconf_params - mesh configuration parameters * - * Mesh configuration parameters + * Mesh configuration parameters. These can be changed while the mesh is + * active. * * @__NL80211_MESHCONF_INVALID: internal use * * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in * millisecond units, used by the Peer Link Open message * - * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in + * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in * millisecond units, used by the peer link management to close a peer link * * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in @@ -1523,7 +1798,10 @@ enum nl80211_mntr_flags { * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs) * that it takes for an HWMP information element to propagate across the mesh * - * @NL80211_MESHCONF_ROOTMODE: whether root mode is enabled or not + * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not + * + * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a + * source mesh point for path selection elements. * * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute * @@ -1545,6 +1823,7 @@ enum nl80211_meshconf_params { NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL, NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME, NL80211_MESHCONF_HWMP_ROOTMODE, + NL80211_MESHCONF_ELEMENT_TTL, /* keep last */ __NL80211_MESHCONF_ATTR_AFTER_LAST, @@ -1552,6 +1831,54 @@ enum nl80211_meshconf_params { }; /** + * enum nl80211_mesh_setup_params - mesh setup parameters + * + * Mesh setup parameters. These are used to start/join a mesh and cannot be + * changed while the mesh is active. + * + * @__NL80211_MESH_SETUP_INVALID: Internal use + * + * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a + * vendor specific path selection algorithm or disable it to use the default + * HWMP. + * + * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a + * vendor specific path metric or disable it to use the default Airtime + * metric. + * + * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a + * robust security network ie, or a vendor specific information element that + * vendors will use to identify the path selection methods and metrics in use. + * + * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication + * daemon will be authenticating mesh candidates. + * + * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication + * daemon will be securing peer link frames. AMPE is a secured version of Mesh + * Peering Management (MPM) and is implemented with the assistance of a + * userspace daemon. When this flag is set, the kernel will send peer + * management frames to a userspace daemon that will implement AMPE + * functionality (security capabilities selection, key confirmation, and key + * management). When the flag is unset (default), the kernel can autonomously + * complete (unsecured) mesh peering without the need of a userspace daemon. + * + * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number + * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use + */ +enum nl80211_mesh_setup_params { + __NL80211_MESH_SETUP_INVALID, + NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL, + NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC, + NL80211_MESH_SETUP_IE, + NL80211_MESH_SETUP_USERSPACE_AUTH, + NL80211_MESH_SETUP_USERSPACE_AMPE, + + /* keep last */ + __NL80211_MESH_SETUP_ATTR_AFTER_LAST, + NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1 +}; + +/** * enum nl80211_txq_attr - TX queue parameter attributes * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*) @@ -1709,6 +2036,23 @@ enum nl80211_wpa_versions { }; /** + * enum nl80211_key_default_types - key default types + * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid + * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default + * unicast key + * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default + * multicast key + * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types + */ +enum nl80211_key_default_types { + __NL80211_KEY_DEFAULT_TYPE_INVALID, + NL80211_KEY_DEFAULT_TYPE_UNICAST, + NL80211_KEY_DEFAULT_TYPE_MULTICAST, + + NUM_NL80211_KEY_DEFAULT_TYPES +}; + +/** * enum nl80211_key_attributes - key attributes * @__NL80211_KEY_INVALID: invalid * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of @@ -1724,6 +2068,9 @@ enum nl80211_wpa_versions { * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not * specified the default depends on whether a MAC address was * given with the command using the key or not (u32) + * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags + * attributes, specifying what a key should be set as default as. + * See &enum nl80211_key_default_types. * @__NL80211_KEY_AFTER_LAST: internal * @NL80211_KEY_MAX: highest key attribute */ @@ -1736,6 +2083,7 @@ enum nl80211_key_attributes { NL80211_KEY_DEFAULT, NL80211_KEY_DEFAULT_MGMT, NL80211_KEY_TYPE, + NL80211_KEY_DEFAULT_TYPES, /* keep last */ __NL80211_KEY_AFTER_LAST, @@ -1786,6 +2134,8 @@ enum nl80211_ps_state { * the minimum amount the RSSI level must change after an event before a * new event may be issued (to reduce effects of RSSI oscillation). * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event + * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many + * consecutive packets were not acknowledged by the peer * @__NL80211_ATTR_CQM_AFTER_LAST: internal * @NL80211_ATTR_CQM_MAX: highest key attribute */ @@ -1794,6 +2144,7 @@ enum nl80211_attr_cqm { NL80211_ATTR_CQM_RSSI_THOLD, NL80211_ATTR_CQM_RSSI_HYST, NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT, + NL80211_ATTR_CQM_PKT_LOSS_EVENT, /* keep last */ __NL80211_ATTR_CQM_AFTER_LAST, @@ -1825,4 +2176,189 @@ enum nl80211_tx_power_setting { NL80211_TX_POWER_FIXED, }; +/** + * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute + * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute + * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has + * a zero bit are ignored + * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have + * a bit for each byte in the pattern. The lowest-order bit corresponds + * to the first byte of the pattern, but the bytes of the pattern are + * in a little-endian-like format, i.e. the 9th byte of the pattern + * corresponds to the lowest-order bit in the second byte of the mask. + * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where + * xx indicates "don't care") would be represented by a pattern of + * twelve zero bytes, and a mask of "0xed,0x07". + * Note that the pattern matching is done as though frames were not + * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked + * first (including SNAP header unpacking) and then matched. + * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes + * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number + */ +enum nl80211_wowlan_packet_pattern_attr { + __NL80211_WOWLAN_PKTPAT_INVALID, + NL80211_WOWLAN_PKTPAT_MASK, + NL80211_WOWLAN_PKTPAT_PATTERN, + + NUM_NL80211_WOWLAN_PKTPAT, + MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1, +}; + +/** + * struct nl80211_wowlan_pattern_support - pattern support information + * @max_patterns: maximum number of patterns supported + * @min_pattern_len: minimum length of each pattern + * @max_pattern_len: maximum length of each pattern + * + * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when + * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the + * capability information given by the kernel to userspace. + */ +struct nl80211_wowlan_pattern_support { + __u32 max_patterns; + __u32 min_pattern_len; + __u32 max_pattern_len; +} __attribute__((packed)); + +/** + * enum nl80211_wowlan_triggers - WoWLAN trigger definitions + * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes + * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put + * the chip into a special state -- works best with chips that have + * support for low-power operation already (flag) + * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect + * is detected is implementation-specific (flag) + * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed + * by 16 repetitions of MAC addr, anywhere in payload) (flag) + * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns + * which are passed in an array of nested attributes, each nested attribute + * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern. + * Each pattern defines a wakeup packet. The matching is done on the MSDU, + * i.e. as though the packet was an 802.3 packet, so the pattern matching + * is done after the packet is converted to the MSDU. + * + * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute + * carrying a &struct nl80211_wowlan_pattern_support. + * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers + * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number + */ +enum nl80211_wowlan_triggers { + __NL80211_WOWLAN_TRIG_INVALID, + NL80211_WOWLAN_TRIG_ANY, + NL80211_WOWLAN_TRIG_DISCONNECT, + NL80211_WOWLAN_TRIG_MAGIC_PKT, + NL80211_WOWLAN_TRIG_PKT_PATTERN, + + /* keep last */ + NUM_NL80211_WOWLAN_TRIG, + MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1 +}; + +/** + * enum nl80211_iface_limit_attrs - limit attributes + * @NL80211_IFACE_LIMIT_UNSPEC: (reserved) + * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that + * can be chosen from this set of interface types (u32) + * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a + * flag attribute for each interface type in this set + * @NUM_NL80211_IFACE_LIMIT: number of attributes + * @MAX_NL80211_IFACE_LIMIT: highest attribute number + */ +enum nl80211_iface_limit_attrs { + NL80211_IFACE_LIMIT_UNSPEC, + NL80211_IFACE_LIMIT_MAX, + NL80211_IFACE_LIMIT_TYPES, + + /* keep last */ + NUM_NL80211_IFACE_LIMIT, + MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1 +}; + +/** + * enum nl80211_if_combination_attrs -- interface combination attributes + * + * @NL80211_IFACE_COMB_UNSPEC: (reserved) + * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits + * for given interface types, see &enum nl80211_iface_limit_attrs. + * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of + * interfaces that can be created in this group. This number doesn't + * apply to interfaces purely managed in software, which are listed + * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE. + * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that + * beacon intervals within this group must be all the same even for + * infrastructure and AP/GO combinations, i.e. the GO(s) must adopt + * the infrastructure network's beacon interval. + * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many + * different channels may be used within this group. + * @NUM_NL80211_IFACE_COMB: number of attributes + * @MAX_NL80211_IFACE_COMB: highest attribute number + * + * Examples: + * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2 + * => allows an AP and a STA that must match BIs + * + * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8 + * => allows 8 of AP/GO + * + * numbers = [ #{STA} <= 2 ], channels = 2, max = 2 + * => allows two STAs on different channels + * + * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4 + * => allows a STA plus three P2P interfaces + * + * The list of these four possiblities could completely be contained + * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate + * that any of these groups must match. + * + * "Combinations" of just a single interface will not be listed here, + * a single interface of any valid interface type is assumed to always + * be possible by itself. This means that implicitly, for each valid + * interface type, the following group always exists: + * numbers = [ #{<type>} <= 1 ], channels = 1, max = 1 + */ +enum nl80211_if_combination_attrs { + NL80211_IFACE_COMB_UNSPEC, + NL80211_IFACE_COMB_LIMITS, + NL80211_IFACE_COMB_MAXNUM, + NL80211_IFACE_COMB_STA_AP_BI_MATCH, + NL80211_IFACE_COMB_NUM_CHANNELS, + + /* keep last */ + NUM_NL80211_IFACE_COMB, + MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1 +}; + + +/** + * enum nl80211_plink_state - state of a mesh peer link finite state machine + * + * @NL80211_PLINK_LISTEN: initial state, considered the implicit + * state of non existant mesh peer links + * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to + * this mesh peer + * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received + * from this mesh peer + * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been + * received from this mesh peer + * @NL80211_PLINK_ESTAB: mesh peer link is established + * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled + * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh + * plink are discarded + * @NUM_NL80211_PLINK_STATES: number of peer link states + * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states + */ +enum nl80211_plink_state { + NL80211_PLINK_LISTEN, + NL80211_PLINK_OPN_SNT, + NL80211_PLINK_OPN_RCVD, + NL80211_PLINK_CNF_RCVD, + NL80211_PLINK_ESTAB, + NL80211_PLINK_HOLDING, + NL80211_PLINK_BLOCKED, + + /* keep last */ + NUM_NL80211_PLINK_STATES, + MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1 +}; + #endif /* __LINUX_NL80211_H */ |