| Age | Commit message (Collapse) | Author |
|---|
|
Under certain circumstances, the device may not have enough resources to
enable all of the VFs that it advertises in config space. Although the
number of supported VFs is reported upon driver init, it is not obvious
when this is different from the number reported in config space. To
eliminate this confusion, add an error message explaining the problem.
Additionally, move the 'Allocating VFs' message down below the error
checks so as to prevent further confusion.
Change-ID: I45b7efca53a7aebf7777be33a8bc9d615ae48ea1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The interrupt enable function can be inlined by moving it to the header
file, which decreases the function call overhead for a frequently called
function.
Change-ID: I3214cc99593725768642680e7b8ce7e9bba7e44d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was issuing a WARN_ON during ring size changes
because the code was cloning the rx_ring struct but
not zeroing out the pointers before allocating new memory.
Zero out the pointers in the cloned copy before allocating
new memory for them. In this case the code was correctly
avoiding memory leaks but still triggering the warning.
Change-ID: I186dd493948e9b7254ab0593d4aad8b68808918d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Change-ID: I0a76c52427dadf97d4dba4538a3068d05e4eb56b
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously, the driver could call this function and have only true/false
returned, but false could mean multiple things like failure to read
or link was down. This change allows the caller to get all return values
in the call chain bubbled back to the source, which keeps information about
failures from being lost.
Also, in some unlikely scenarios, the firmware can become slow to respond
to admin queue (AQ) queries for link state. Should the AQ time out,
the driver can detect the state and avoid a link change when there
may have been none.
Change-ID: Ib2ac38407b7880750fb891b392fa77457fe6c21c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The checksum is not correct on big endian machines so add code to swap it
correctly.
Change-ID: Ic92b886d172a2cbe49f5d7eee1bc78e447023c7b
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ethtool, there is a possibility of speed getting set to 0
if advertise is set to 0 (which it is when autoneg is disabled).
We never want this to happen as the firmware will actually attempt
to set the speed to 0 sending link down, so add an extra check
to make sure this doesn't happen.
Change-ID: I62e0eeee2cbf043d8e6f5c9c9f0b92794e877f01
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch extends the size of the text available for the interrupt names.
Without this patch, all the descriptive data available for the Flow
Director interrupts is truncated.
Change-ID: I2ac458f23ac3b4ea8f1edf73edc283b1d3704c7f
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40e_init_pf_fcoe() didn't return anything except 0, it prints enough
error info already, and no driver logic depends on the return value,
so this can be void.
Change-ID: Ie6afad849857d87a7064c42c3cce14c74c2f29d8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a shift value that was wrong, ending up with a bad bitmask. Also add
a blank line between two sets of #defines for better readability.
Change-ID: I3e41fa2a2ab904d3a4e6cbf13972ab0036a10601
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.
Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Explicitly stop the rings belonging to each VF when disabling SR-IOV.
Even though the VFs were gone, and the associated VSIs were removed, the
rings were not stopped, and in some circumstances the hardware would
continue to access the memory formerly used by the rings, causing memory
corruption or DMAR errors, both of which would lead to general malaise
of the kernel.
To relieve this condition, explicitly stop all the rings associated with
each VF before releasing its resources.
Change-ID: I78c05d562c66e7b594b7e48d67860f49b3e5b6ec
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was disabling Wake-on-LAN by default and waiting for the user
to expressly turn it on. This patch has the driver turning on WoL from
the start if enabled in the hardware config, which matches the behavior
of our other drivers.
Change-ID: I43faedb907f8ba4d1a61b72a7c86072b97af12b1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some rare cases the reset can take longer to complete so increase the
amount of time we wait.
Change-ID: Ib5628ec54b526a811ee33d1214fe763226406671
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver still was not offloading TSO on GRE tunnels because
it forgot to set the GSO_GRE flag, causing lots of retransmits.
This fixes generic GRE traffic (like a tunnel added like below)
whereas before it would get 1Gb/s or less, now on a 10G adapter
it gets 8.7Gb/s.
ip ad ad 11.1.0.2/24 dev ens2f0
ip l set ens2f0 up
ip link add gre2 type gretap remote 11.1.0.1 local 11.1.0.2 dev ens2f0
ip l set gre2 up
ip ad ad 192.168.124.2/24 dev gre2
ping 192.168.124.1
netperf -H 192.168.124.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we have the spinlocks before we clear the ARQ and ASQ management
registers. Also, widen the locked portion and make a sanity check earlier
in the send function to be sure we're working with safe register values.
Change-ID: I34b56044b33461ed780f3d2de8d62826cdf933f9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In any case free the memory allocated before exiting.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Function i40e_clean_rx_irq() tries to reuse memory pages allocated
from the nearest node. To better support memoryless node, use
numa_mem_id() instead of numa_node_id() to get the nearest node with
memory.
This change should only affect performance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-30
This series contains updates to i40e and i40evf only.
Vasily Averin provides a couple of rtnl lock/unlock fixes for both i40e
and i40evf.
Shannon provides several updates and fixes, first fixes up a type clash
in i40e_aq_rc_to_posix(), where the error codes are signed values, so we
need to treat them as such. Then fixes up a padding issue where an
extra byte is added in i40e_aqc_get_cee_dcb_cfg_v1_resp to directly
acknowledge the padding. Updated i40e to keep debugfs register read
and writes from accessing outside of the io-remapped space. Added
support and device id for another 20 GbE device.
Jesse fixes the transmit hand workaround code for ARM that was causing
Tx hangs to still occur occasionally when there really was no hang. Then
fixed the receive dropped counter to show up in netstat interface.
Refactor the interrupt enable function since it was always making the
caller add the base_vector from the VSI struct which is already passed
to the function. Fix kbuild warnings found in 0day build infrastructure
by adding a harmless cast to a dev_info(), also fix 32 bit build
warnings found by sparse.
Greg fixed a configuration error that results if a port VLAN is set
for a VF before the VF driver is loaded, so that when the VF driver is
loaded the port VLAN is ignored.
Mitch fixes the use of QOS field consistently in
i40e_ndo_set_vf_port_vlan(). Modified the init timing of the driver
to increase stability on load/unload and SR-IOV enable/disable cycles.
Anjali updates i40e to not collect VEB stats if they are disabled in the
hardware for performance reasons.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/dsa/slave.c
net/dsa/slave.c simply had overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sparse found some issues with 32 bit compilation, which probably should
at least work without warning. Not only that, but the code was wrong.
Thanks sparse!!
And thanks to the kbuild robot zero day testing for finding this issue.
$ make ARCH=i386 M=drivers/net/ethernet/intel/i40e C=2 CF="-D__CHECK_ENDIAN__"
CHECK drivers/net/ethernet/intel/i40e/i40e_main.c
include/linux/etherdevice.h:79:32: warning: restricted __be16 degrades to integer
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (32) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (42) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (39) for type unsigned long
drivers/net/ethernet/intel/i40e/i40e_main.c:7565:17: warning: shift too big (40) for type unsigned long
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The 0day build infrastructure found some issues in i40e, this
removes the warnings by adding a harmless cast to a dev_info.
CC: kbuild-all@01.org
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Down was requesting queue disables, but then exited immediately without
waiting for the queues to actually disable. This could allow any
function called after i40evf_down to run immediately, including
i40evf_up, and causes a memory leak.
This issue has been fixed in a recent refactor of the reset code, but
add a couple WARN_ONs in the slow path to help us recognize if we
reintroduce this issue or if we missed any cases.
Change-ID: I27b6b5c9a79c1892f0ba453129f116bc32647dd0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The interrupt enable function was always making the caller add
the base_vector from the VSI struct which is already passed to
the function. Just collapse the math into the helper function.
Change-ID: I54ef33aa7ceebc3231c3cc48f7b39fd0c3ff5806
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Due to performance reasons, VEB stats have been disabled in the hw. This
patch adds code to check for that condition before accumulating these
stats.
Change-ID: I7d805669476fedabb073790403703798ae5d878e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add new device id and support for another 20Gb device.
Change-ID: Ib1b61e5bb6201d84953f97cade39a6e3369c2cf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove a useless message that blathers on whenever a vxlan port is deleted.
Change-ID: If63fb8cf38e56cf433b68e498f11389de51919ba
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Don't let the debugfs register read and write commands try to access
outside of the ioremapped space. While we're at it, remove the use of
a misleading constant.
Change-ID: Ifce2893e232c65c7a76c23532c658f298218a81b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In i40e_ndo_set_vf_port_vlan, we were using the QOS value
inconsistently, sometimes shifting it, sometimes not. Do the shift-and-
or operation correctly, once, and use the result consistently everywhere
in the function.
Change-ID: I46f062f3edc90a8a017ecec9137f4d1ab0ab9e41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e rx_dropped counter was not showing up in netstat -i.
Add the right counter to be updated with the stats.
Change-ID: I4dd552e9995836099184f9d9a08e90edb591155f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The arm writeback (arm_wb) code is used for kicking the Tx ring to
make sure any pending work is completed even if interrupts are
disabled. It was running when it didn't need to, and not clearing
the ring->arm_wb state after it was set. This caused Tx hangs
to still occur occasionally when there really was no hang.
Fix this by resetting the variable right after it was used.
Change-ID: I7bf75d552ba9c4bd203d40615213861a24bb5594
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The struct i40e_aqc_get_cee_dcb_cfg_v1_resp was originally defined with
word boundary layout issues, which most compilers deal with by silently
adding padding, making the actual struct larger than designed.
This patch adds an extra byte in fields reserved3 and reserved4 to directly
acknowledge that padding.
Because the struct doesn't actually change in size or layout, this doesn't
constitute a change in the API.
Change-ID: I53fa4741b73fa255621232a85fba000b0e223015
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If a port VLAN is set for a given virtual function (VF) before the VF
driver is loaded then a configuration error results in which the port
VLAN is ignored when the VF driver is subsequently loaded. This causes
the VF's MAC/VLAN filters to not use the correct VLAN filter. This
patch ensures that the port VLAN filter is considered at the right time
during configuration of the VF's MAC/VLAN filters.
Change-ID: I28f404cbc21a4c6d70a7980b87c77f13f06685a4
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The error code sent into i40e_aq_rc_to_posix() are signed values, so we
really need to treat them as such.
Change-ID: I3d1ae0ee9ae0b1b6f5fc424f8b8cc58b0ea93203
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It's possible that while we are waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If we then attempt to use the queue, we will panic.
Add a check for this condition on the receive side. This matches
an existing check on the send queue side.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously to this patch, the hardware was removing
VLAN tags from the inner header of VXLAN packets. The
hardware configuration can be changed to leave the
packet alone since that is what the linux stack
expects for this type of VLAN in VXLAN packet.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sync_vsi_filters function can be called directly under RTNL
or through the timer subtask without one. This was causing a deadlock.
If sync_vsi_filters is called from a thread which held the lock,
and in another thread the PROMISC setting got changed we would
be executing the PROMISC change in the thread which already held
the lock alongside the other filter update. The PROMISC change
requires a reset if we are on a VEB, which requires it to be called
under RTNL.
Earlier the driver would call reset for PROMISC change without
checking if we were already under RTNL and would try to grab it
causing a deadlock. This patch changes the flow to see if we are
already under RTNL before trying to grab it.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the issue of forcing WB too often causing us to not
benefit from NAPI.
Without this patch we were forcing WB/arming interrupt too often taking
away the benefits of NAPI and causing a performance impact.
With this patch we disable force WB in the clean routine for X710
and XL710 adapters. X722 adapters do not enable interrupt to force
a WB and benefit from WB_ON_ITR and hence force WB is left enabled
for those adapters.
For XL710 and X710 adapters if we have less than 4 packets pending
a software Interrupt triggered from service task will force a WB.
This patch also changes the conditions for setting RS bit as described
in code comments. This optimizes when the HW does a tail bump and when
it does a WB. It also optimizes when we do a wmb.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make sure the Tx checksum encoder knows about GRE protocol and sets the
descriptor flag appropriately.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch modifies the driver timeout logic by issuing a writeback
request via a software interrupt to the hardware the first time the
driver detects a hang. The driver was too aggressive in resetting a hung
queue, so back that off by removing logic to down the netdevice after
too many hangs, and move the function to the service task.
Change-ID: Ife100b9d124cd08cbdb81ab659008c1b9abbedea
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40e_get_head needs to be called in multiple files in a further patch,
prepare by moving the function into a header file.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump.
Change-ID: If7ce84218361defa209142d1d8c6f69d48c2d7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
