| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-10-19
This series contains updates to i40e and i40evf only.
Kiran adds a spinlock around code accessing VSI MAC filter list to
ensure that we are synchronizing access to the filter list, otherwise
we can end up with multiple accesses at the same time which can cause
the VSI MAC filter list to get in an unstable or corrupted state.
Jesse fixes overlong BIT defines, where the RSS enabling call were
mistakenly missed. Also fixes a bug where the enable function was
enabling the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx, while refactoring the IRQ
enable function to simplify reading the flow. Addressed the high
CPU utilization of some small streaming workloads that the driver should
reduce CPU in.
Anjali fixes two X722 issues with respect to EEPROM checksum verify and
reading NVM version info. Fixed where a mask value was accidentally
replaced with a bit mask causing Flow Director sideband to be broken.
Alex Duyck fixes areas of the drivers which run from hard interrupt
context or with interrupts already disabled in netpoll, so use
napi_schedule_irqoff() instead of napi_schedule().
Mitch fixes the VF drivers to not easily give up when it is not able
to communicate with the PF driver.
Carolyn fixes a problem where our tools MAC loopback test, after driver
unbind would fail because the hardware was configured for multiqueue and
unbind operation did not clear this configuration. Also fixed a issue
where the NVMUpdate tool gets bad data from the PHY when using the PHY
NVM feature because of contention on the MDIO interface from getting
PHY capability calls from the driver during regular operations.
Catherine fixed an issue where we were checking if autoneg was allowed
to change before checking if autoneg was changing, these checks need to
be in the reverse order.
Jean Sacren fixes up an function header comment to align the kernel-docs
with the actual code.
v2: Cleaned up the use of spin_is_locked() in patch 1 based on feedback
from David Miller, since it always evaluates to zero on uni-processor
builds
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bump.
Change-ID: Id0a7ecaa491f88ce94c9eba4901e592a56044ee0
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A mask value of 0x1FF was accidentally replaced with a bit mask
causing flow director sideband to be broken.
Change-ID: Id3387f67dd1b567b41692b570b383c58671e1eae
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The dynamic algorithm, while now working, doesn't have good
performance in 40G mode.
One part of this patch addresses the high CPU utilization of some small
streaming workloads that the driver should reduce CPU in.
It also changes the minimum ITR that the dynamic algorithm
will settle on, causing our minimum latency to go from 12us
to about 14us, when using adaptive mode.
It also changes the BULK interrupt rate to allow maximum throughput
on a 40Gb connection with a single thread of transmit, clamping
interrupt rate to 8000 for TX makes single thread traffic go too
slow.
The new ULTRA bulk setting is introduced and is used
when the Rx packet rate on this queue exceeds 40000 packets per
second. This value of 40000 was chosen because the automatic tuning
of minimum ITR=20us means that a single queue can't quite achieve
that many packets per second from a round-robin test.
Change-ID: Icce8faa128688ca5fd2c4229bdd9726877a92ea2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was using a value expressed in 2us increments
for the divisor to figure out our bytes/usec values.
Fix the usecs variable to contain a value in microseconds.
Change-ID: I5c20493103c295d6f201947bb908add7040b7c41
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change moves a multi-line register setting into a function
which simplifies reading the flow of the enable function.
This also fixes a bug where the enable function was enabling
the interrupt twice while trying to update the two interrupt
throttle rate thresholds for Rx and Tx.
Change-ID: Ie308f9d0d48540204590cb9d7a5a7b1196f959bb
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the VF driver is unable to communicate with the PF, it just gives
up and never tries again. Aside from the obvious character flaw that
this shows, it's also a lousy user experience.
When PF communications fail, wait five seconds, and try again. And
again. Don't give up, little VF driver! Your prince will come!
Change-ID: Ia1378a39879883563b8faffce819f375821f9585
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e_intr and i40e/i40evf_msix_clean_rings functions run from hard
interrupt context or with interrupts already disabled in netpoll.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The defines from the RSS enabling call were mistakenly
missed in the patches to the i40e which should have been
to i40evf as well.
This is a follow up to (commit ed921559886dd40528) "fix
32 bit build warnings".
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump.
Change-ID: I7ec818a507554648675b9b245ced9e6b6bd9ed4e
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The vlan_features field was correctly being set to the same value as the
netdev features field. However, this was being done before the features
were actually being set up, leaving the vlan_features empty.
Also, after a reset, vlan_features will be incorrectly assigned the
previous netdev feature flags, which can contain VLAN feature bits. This
makes the VLAN code angry and will cause a stack dump.
To fix these issues, set up the netdev features first, then mask out the
VLAN feature bits when assigning vlan_features.
Change-ID: Ib0548869dc83cf6a841cb8697dd94c12359ba4d2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The XL710 hardware has a different interrupt moderation design
that can support a limit of total interrupts per second per
vector, in addition to the "number of interrupts per second"
controls already established in the driver. This combination
of hardware features allows us to set very low default latency
settings but minimize the total CPU utilization by not
making too many interrupts, should the user desire.
The current driver implementation is still enabling the dynamic
moderation in the driver, and only using the rx/tx-usecs
limit in ethtool to limit the interrupt rate per second, by default.
The new code implemented in this patch
2) adds init/use of the new "Interrupt Limit" register
3) adds ethtool knob to control/report the limits above
Usage is ethtool -C ethx rx-usecs-high <value> Where <value> is number
of microseconds to create a rate of 1/N interrupts per second,
regardless of rx-usecs or tx-usecs values. Since there is a credit based
scheme in the hardware, the rx-usecs and tx-usecs can be configured for
very low latency for short bursts, but once the credit runs out the
refill rate on the credits is limited by rx-usecs-high.
Change-ID: I3a1075d3296123b0f4f50623c779b027af5b188d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add const to functions that return strings that aren't going to be
modified. This addresses some reported compile complaints.
Change-ID: Ic56b1e814ab4d23a50480e7fdec652445f776ee8
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As per Eric Dumazet's previous patches:
(see commit (24d2e4a50737) - tg3: use napi_complete_done())
Quoting verbatim:
Using napi_complete_done() instead of napi_complete() allows
us to use /sys/class/net/ethX/gro_flush_timeout
GRO layer can aggregate more packets if the flush is delayed a bit,
without having to set too big coalescing parameters that impact
latencies.
</end quote>
Tested
configuration: low latency via ethtool -C ethx adaptive-rx off
rx-usecs 10 adaptive-tx off tx-usecs 15
workload: streaming rx using netperf TCP_MAERTS
igb:
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.48 10^6bits/s over 1.000 seconds ending at 1440193171.589
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1176930056 1475.36 797726 16384.00 71905
MIGRATED TCP MAERTS TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 10.0.0.1 () port 0 AF_INET : demo
...
Interim result: 941.49 10^6bits/s over 0.997 seconds ending at 1440193142.763
Alignment Offset Bytes Bytes Recvs Bytes Sends
Local Remote Local Remote Xfered Per Per
Recv Send Recv Send Recv (avg) Send (avg)
8 8 0 0 1175182320 50476.00 23282 16384.00 71816
i40e:
Hard to test because the traffic is incoming so fast (24Gb/s) that GRO
always receives 87kB, even at the highest interrupt rate.
Other drivers were only compile tested.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The polling routine for i40e was rounding up the budget for Rx cleanup to
1. This is incorrect as the netpoll poll call is expecting no Rx to be
processed as the budget passed was 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump.
Change-ID: I8d9a99f320af43960deba8718eee2d6de50eaf46
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Shorten up the delays in the init task, allowing the VF driver to
initialize faster. This aids performance in load/unload tests and
mitigates DMAR errors in VF enable/disable tests with absurdly short
delays. In the real world, the VF driver will come up more quickly.
The original values were set conservatively based on what we expected
from the firmware in terms of performance. Now that the driver is in use
and we know how well firmware responds to our requests, we can shorten
these delays.
Change-ID: Ibead77d34b19e8170e667c3f58bc14748bbc5bc9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove a variable declaration inside an if block hiding an existing
declaration at the start of the function.
Also remove a forward function declaration that is no longer needed due
to code re-organization.
Change-ID: I12954668b722718074949c93d74cd20eaacd93e4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X722 has a way to work around the descriptor WB issue,
this offload helps turn that feature on.
Change-ID: I7ffa67622426bfca5a651417b63e3afcfeb60412
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Bump.
Change-ID: If3cd42f6c1b9546beed60faf9c79faab35216f58
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information
will help us determine what speeds the device is capable of when link is
down.
Also add an enum to decode the PHY types the NVM is capable of.
Use the phy_types variable to determine what phy types are possible
when link is down instead of device id as it will be more accurate.
When on a backplane device, we do not support changing any settings,
however we should display all the phy_types we are capable of so if we
see a backplane dev ID set supported and advertised purely based on
the phy_types variable.
Change-ID: Ia75d560f1fcd30c54cbfb7458690c5867559a930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add a module_types variable to the link_info struct to save the module
information from get_phy_capabilities. This information can be used to
determine which speeds the module supports.
Also add a new function update_link_info which updates the module_types
parameter and then calls get_link_info. This function should be called
in place of get_link_info so that the module_types variable stays
up-to-date with the rest of the link information.
The EAS table does not reflect the values that are actually returned,
so instead, basing these values on the Ethernet compliance codes
specified in table 33 of SFF-8436 as these have been accurate.
Use the new variable in ethtool to differentiate between a 10G/1G dual
speed fiber module and a 10G only module.
Change-ID: Ib7585cce321319c10ce15180054c41a6cbd41389
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Due to desires to write userland drivers, and other requests, without
needing the rest of the include files, the device ids are pulled out
into a standalone file.
Change-ID: Ic0b047dbf9d4b0891892309c1f2079f56d9b60e8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a member to the nvm_info struct for oem_ver info to be
output either by OID or ethtool.
Change-ID: I1e5d513ae67622e2af17042924fdb4b5d6d85366
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was not correctly handling calls to its ndo_set_mac_address
method. It did not properly check to see if the override would be
allowed by the PF driver, and never removed the old address from its
filter list.
Add a new flag to the adapter struct which is set if the MAC address is
assigned by the PF. Check this flag and don't allow the MAC address to
be changed if it is set. Search for and properly remove the filter
for the old MAC address when the new one is set.
Change-ID: I817bf620c869c5a80e6a7eab65c9cbad1dc89799
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the new Port link status bit and rename the link status to function
link status.
Change-ID: I71289327ae62638ce967b6ad40114caf998b6dab
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.
Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the capabilities passed to us by the PF driver to control VF driver
behavior. In the process, clean up the VLAN add/remove code so it's not
a horrible morass of ifdefs.
Change-ID: I1050eaf12b658a26fea6813047c9964163c70a73
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using VFGEN_RSTAT to detect a VF reset is an endeavor that is fraught
with peril. It's entirely too easy to miss a reset because none of the
bits are sticky. By the time the VF driver reads the register, the reset
may have been processed and cleaned up by the PF driver, leaving the
register in the same state that it was before the reset.
Instead, detect a reset with the VF_ARQLEN register. When the VF is
reset, the enable bit in this register is cleared, and it stays cleared
until the VF driver processes the reset and re-enables the admin queue.
Because we now deal with multiple registers in the reset and watchdog
tasks, rename the rstat_val variable to reg_val.
Change-ID: Id1df17045c0992e607da0162d31807f7fc20d199
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Ran into an issue where PF's VSI type list was different from VF's,
which was resulted in different enum index. The VSI type list can
be different depending on what build flag is used for PF and VF.
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type event if the
enum lists are different.
Change-ID: I8c0e5fdb515f324f7964df863a458073cf467e57
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Change-ID: I19c550369594384eaff4cc63e690ca740231195d
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This opcode is not required. VFs that program RSS through the firmware
do it by interacting directly with the firmware, and do not need to use
the virtual channel for this functionality.
Change-ID: Iaf17d2600e28ff1b6be8653f2fe9df1facd23b0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Lower level functions are properly reporting errors, and higher-level
functions are correctly responding to errors, but the errors aren't
actually getting through. Typically, the middle-manager function seems
to want to shield its boss from any bad news.
This change fixes a panic if the driver is unable to enable MSI-X or is
unable to acquire enough vectors.
Change-ID: Ifd5787ce92519a5d97e4b465902db930d97b71a1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Keep track of how many times we ask the stack to linearize the
skb because the HW cannot handle skbs with more than 8 frags per
segment/single packet.
Change-ID: If455452060963a769bbe6112cba952e79e944b52
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using something like "ip maddr add ..." to add another unicast mac
address to the netdev, the mac address comes into the set_rx_mode handler
in the multicast list whether it is a unicast or multicast address.
This was confusing the code when it was trying to search for addresses
that needed to be deleted from the VSI, because it was looking for the
VSI unicast address in the netdev unicast list. The result was that a
new unicast address would get added to the VSI list and then immediately
removed, and would never actually make it down into the hardware.
This patch removes the separation from unicast and multicast in the search
for filters to be deleted. It also simplifies the logic a little with a
jump to the bottom of the loop when an address is found. Now it doesn't
matter which netdev list the address is hiding in, we'll check them all.
Change-ID: Ie3685a92427ae7d2212bf948919ce295bc7a874c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During early development, we added the function name to all of the error
strings to make debugging simpler. Now that we've released the driver,
our users should have more comprehensible error messages. So tear the
roof off and give up the __func__. Ow.
Change-ID: I7e1766252c7a032b9af6520da6aff536bdfd533c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was a possibility where the asq_last_status could get through without
update and thus report a previous error. I don't think we've actually seen
this happen, but this patch will help make sure it doesn't.
Change-ID: I9e33927052a5ee6ea21f80b66d4c4b76c2760b17
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Rework an if expression to assure there is no type compare problem between
a size and a possible negative number.
Change-ID: I4921fcc96abfcf69490efce020a9e4007f251c99
Reported-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Early addition of new a device id.
Change-ID: I61a8c8556fdf4f5714be4e4089689e374f30293c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The standard way to check if the AQ is enabled is to look at the
count field. So we should only set this field after we have
successfully allocated memory. To do otherwise is to incite
panic among the populace.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain circumstances, we can get an extra VF_RESOURCES message
from the PF driver at runtime. When this happens, we need to parse it
because our VSI may have changed out from underneath us, and that will
affect our relationship with the PF driver.
However, parsing the resources message also blows away our current MAC
address in the hardware struct, usually with all zeros. When this
happens, the next time the interface is opened, it will have no MAC
address and will a) not work and b) complain.
Fix this issue by restoring the current MAC address from the netdev
struct after we parse the resource message.
Change-ID: I6cd1b624fc20432f81dc901166c8de195b8e0e65
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make sure we have the spinlocks before we clear the ARQ and ASQ management
registers. Also, widen the locked portion and make a sanity check earlier
in the send function to be sure we're working with safe register values.
Change-ID: I34b56044b33461ed780f3d2de8d62826cdf933f9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Function i40e_clean_rx_irq() tries to reuse memory pages allocated
from the nearest node. To better support memoryless node, use
numa_mem_id() instead of numa_node_id() to get the nearest node with
memory.
This change should only affect performance.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
