summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2011-04-07Merge branch 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6Linus Torvalds
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6: Fix common misspellings
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-29carl9170: Fix tx aggregation problems with some clientsChristian Lamparter
Some clients seem to rely upon the reception of BlockAckReqs to flush their rx reorder buffer. In order to fix aggregation for these clients carl9170 should set IEEE80211_TX_STAT_AMPDU_NO_BACK to generate a BlockAckReq if the transmission of an AMPDU subframe fails. This fixes aggregation problems with Intel 5100 Windows STAs (and maybe others as well). Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-28ath9k: fix a chip wakeup related crash in ath9k_startFelix Fietkau
When the chip is still asleep when ath9k_start is called, ath9k_hw_configpcipowersave can trigger a data bus error. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-23ath9k: Fix TX queue stuck issue.Senthil Balasubramanian
commit 86271e460a66003dc1f4cbfd845adafb790b7587 introduced a regression that caused mac80211 queues in stopped state. ath_drain_all_txq is called in driver flush which would reset the stopped flag and the mac80211 queues were never started after that. iperf traffic is completely stalled due to this issue. Restart the mac80211 queues in driver flush only if the txqs were drained. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-23ath9k: Fix kernel panic caused by invalid rate index access.Senthil Balasubramanian
With the recent tx status optimization in mac80211, we bail out as and and when invalid rate index is found. So the behavior of resetting rate idx to -1 and count to 0 has changed for the rate indexes that were not part of the driver's retry series. This has resulted in ath9k using incorrect rate table index which caused the system to panic. Ideally ath9k need to loop only for the indexes that were part of the retry series and so simply use hw->max_rates as the loop counter. Pasted the stack trace of the panic issue for reference. [ 754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0 [ 754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k] [ 754.094888] Call Trace: [ 754.094903] <IRQ> [ 754.094928] [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211] [ 754.094975] [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211] [ 754.095017] [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k] [ 754.095054] [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k] [ 754.095098] [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211] [ 754.095148] [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40 [ 754.095186] [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k] [ 754.095224] [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0 [ 754.095261] [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k] [ 754.095298] [<ffffffff8105599b>] tasklet_action+0x6b/0xe0 [ 754.095331] [<ffffffff81056278>] __do_softirq+0x98/0x120 [ 754.095361] [<ffffffff8100cd5c>] call_softirq+0x1c/0x30 [ 754.095393] [<ffffffff8100efb5>] do_softirq+0x65/0xa0 [ 754.095423] [<ffffffff810563fd>] irq_exit+0x8d/0x90 [ 754.095453] [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0 [ 754.095482] [<ffffffff81351413>] ret_from_intr+0x0/0x15 [ 754.095513] <EOI> [ 754.095531] [<ffffffff81014375>] ? native_sched_clock+0x15/0x70 [ 754.096475] [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor] [ 754.096475] [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor] [ 754.096475] [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100 [ 754.096475] [<ffffffff8100a236>] cpu_idle+0xa6/0xf0 [ 754.096475] [<ffffffff81339bc1>] rest_init+0x91/0xa0 [ 754.096475] [<ffffffff814efccd>] start_kernel+0x3fd/0x408 [ 754.096475] [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136 [ 754.096475] [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115 [ 754.096475] RIP [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k] Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-21ath9k: Fix kernel panic in AR2427Mohammed Shafi Shajakhan
Kernel panic occurs just after AR2427 establishes connection with AP. Unless aggregation is enabled we don't initialize the TID structure. Thus accesing the elements of the TID structure when aggregation is disabled, leads to NULL pointer dereferencing. [ 191.320358] Call Trace: [ 191.320364] [<fd250ea7>] ? ath9k_tx+0xa7/0x200 [ath9k] [ 191.320376] [<fd1ec7fc>] ? __ieee80211_tx+0x5c/0x1e0 [mac80211] [ 191.320386] [<fd1edd2b>] ? ieee80211_tx+0x7b/0x90 [mac80211] [ 191.320395] [<fd1edddd>] ? ieee80211_xmit+0x9d/0x1d0 [mac80211] [ 191.320401] [<c014218f>] ? wake_up_state+0xf/0x20 [ 191.320405] [<c015dbc8>] ? signal_wake_up+0x28/0x40 [ 191.320410] [<c012a578>] ? default_spin_lock_flags+0x8/0x10 [ 191.320420] [<fd1ee308>] ? ieee80211_subif_start_xmit+0x2e8/0x7c0 [mac80211] [ 191.320425] [<c058f905>] ? do_page_fault+0x295/0x3a0 [ 191.320431] [<c04c4a3d>] ? dev_hard_start_xmit+0x1ad/0x210 [ 191.320436] [<c04d96b5>] ? sch_direct_xmit+0x105/0x170 [ 191.320445] [<fd1f161a>] ? get_sta_flags+0x2a/0x40 [mac80211] [ 191.320449] [<c04c780f>] ? dev_queue_xmit+0x37f/0x4b0 [ 191.320452] [<c04d75b0>] ? eth_header+0x0/0xb0 [ 191.320456] [<c04cc479>] ? neigh_resolve_output+0xe9/0x310 [ 191.320461] [<c053d295>] ? ip6_output_finish+0xa5/0x110 [ 191.320464] [<c053e354>] ? ip6_output2+0x134/0x250 [ 191.320468] [<c053f7dd>] ? ip6_output+0x6d/0x100 [ 191.320471] [<c0559665>] ? mld_sendpack+0x395/0x3e0 [ 191.320475] [<c0557f81>] ? add_grhead+0x31/0xa0 [ 191.320478] [<c055a83c>] ? mld_send_cr+0x1bc/0x2b0 [ 191.320482] [<c01535d9>] ? irq_exit+0x39/0x70 [ 191.320485] [<c055a940>] ? mld_ifc_timer_expire+0x10/0x40 [ 191.320489] [<c015b92e>] ? run_timer_softirq+0x13e/0x2c0 [ 191.320493] [<c0103a30>] ? common_interrupt+0x30/0x40 [ 191.320498] [<c055a930>] ? mld_ifc_timer_expire+0x0/0x40 [ 191.320502] [<c0153358>] ? __do_softirq+0x98/0x1b0 [ 191.320506] [<c01534b5>] ? do_softirq+0x45/0x50 [ 191.320509] [<c0153605>] ? irq_exit+0x65/0x70 [ 191.320513] [<c05917dc>] ? smp_apic_timer_interrupt+0x5c/0x8b [ 191.320516] [<c0103df1>] ? apic_timer_interrupt+0x31/0x40 [ 191.320521] [<c016007b>] ? k_getrusage+0x12b/0x2f0 [ 191.320525] [<c039e384>] ? acpi_idle_enter_simple+0x117/0x148 [ 191.320529] [<c04a20da>] ? cpuidle_idle_call+0x7a/0x100 [ 191.320532] [<c01021d4>] ? cpu_idle+0x94/0xd0 [ 191.320536] [<c057ab88>] ? rest_init+0x58/0x60 [ 191.320541] [<c07a58ec>] ? start_kernel+0x351/0x357 [ 191.320544] [<c07a53c7>] ? unknown_bootoption+0x0/0x19e [ 191.320548] [<c07a50aa>] ? i386_start_kernel+0xaa/0xb1 [ 191.320550] Code: 03 66 3d 00 03 0f 84 7c 02 00 00 83 c3 18 0f b6 03 8b 4d e0 89 c3 83 e3 0f 6b c3 48 89 5d d8 8d 04 06 8d 50 0c 89 55 d0 8b 40 20 <8b> 00 3b 01 0f 85 8e 02 00 00 f6 47 20 40 0f 84 29 ff ff ff 8b [ 191.320634] EIP: [<fd2586d4>] ath_tx_start+0x474/0x770 [ath9k] SS:ESP 0068:c0761a90 [ 191.320642] CR2: 0000000000000000 [ 191.320647] ---[ end trace 9296ef23b9076ece ]--- [ 191.320650] Kernel panic - not syncing: Fatal exception in interrupt Cc: stable@kernel.org Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-15Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2011-03-14ath9k: fix aggregation related interoperability issuesFelix Fietkau
Some clients seems to keep track of their reorder window even after an aggregation session has been disabled. This causes issues if there are still retried but not completed frames pending for the TID. To ensure that rx does not stall in such situations, set sendbar to 1 for any frame purged from the TID queue on teardown. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-14ath9k: improve reliability of beacon transmission and stuck beacon handlingFelix Fietkau
ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there is not much point in doing that if the previous beacon and mcast traffic went out properly. On AR9380, calling that function too often can result in an increase of stuck beacons due to differences in the handling of the queue enable/disable functionality. With this patch, the queue will only be explicitly stopped if the previous data frames were not sent successfully. With the beacon code being the only remaining user of ath9k_hw_stoptxdma, this function can be simplified in order to remove the now pointless attempts at waiting for transmission completion, which would never happen at this point due to the different method of tx scheduling of the beacon queue. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-14ath9k: fix the .flush driver op implementationFelix Fietkau
This patch simplifies the flush op and reuses ath_drain_all_txq for flushing out pending frames if necessary. It also uses a global timeout of 200ms instead of the per-queue 60ms timeout. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-14ath9k: fix stopping tx dma on resetFelix Fietkau
In some situations, stopping Tx DMA frequently fails, leading to messages like this: ath: Failed to stop TX DMA in 100 msec after killing last frame ath: Failed to stop TX DMA! This patch uses a few MAC features to abort DMA globally instead of iterating over all hardware queues and attempting to stop them individually. Not only is that faster and works with a shorter timeout, it also makes the process much more reliable. With this change, I can no longer trigger these messages on AR9380, and on AR9280 they become much more rare. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-14ath9k_hw: fix REG_SET_BIT and REG_CLR_BIT for multiple bitsFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11ath5k: implement ieee80211_ops->{get,set}_ringparamJohn W. Linville
set_ringparam only allows changes to tx ring at this time. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11ath9k_hw: Increase the wait count for nf load.Vivek Natarajan
Increasing the wait count makes the nf load pass in most of the cases. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11ath9k_hw: Fix PLL initialization for AR9485.Vivek Natarajan
Increase the delay to make sure the initialization of pll passes. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11ath9k_hw: Improve idle power consumption for AR9485.Vivek Natarajan
Set some GPIO pins to Pull-down mode to save power. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11ath9k: remove support for the FIF_PROMISC_IN_BSS filter flagFelix Fietkau
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad and covers even frames with PHY errors. When this flag is enabled, this message shows up frequently during scanning or hardware resets: ath: Could not stop RX, we could be confusing the DMA engine when we start RX up Since promiscuous mode is usually not particularly useful, yet enabled by default by bridging (either used normally in 4-addr mode, or with hacks for various virtualization software), we should sacrifice it for better reliability during normal operation. This patch leaves it enabled if there are active monitor mode interfaces, since it's very useful for debugging. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-11Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2011-03-09ath5k: restrict AR5K_TX_QUEUE_ID_DATA_MAX to reflect the [0,3] rangeJohn W. Linville
This just matches reality... Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Bob Copeland <me@bobcopeland.com>
2011-03-07wireless:ath: use resource_size() help functionShan Wei
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-07ath5k: Put hardware in PROMISC mode if there is more than 1 stations.Ben Greear
It seems ath5k has issues receiving broadcast packets (ARPs) when using multiple STA interfaces associated with multiple APs. This patch ensures the NIC is always in PROMISC mode if there are more than 1 stations associated. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-04Merge branch 'for-davem' of ↵David S. Miller
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2011-03-04ath9k: Fix txq memory address printing in debugfs.Ben Greear
No use printing addresses of pointers, just print the pointers themselves. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-04ath9k_hw: Read noise floor only for available chains for AR9003Vasanthakumar Thiagarajan
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-04ath9k: Add a debugfs interface to dump chip registersVasanthakumar Thiagarajan
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface to dump the registers. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-03Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bnx2x/bnx2x.h
2011-03-01Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-03-01ath9k_htc: Handle BSSID/AID for multiple interfacesSujith Manoharan
The AID and BSSID should be set in the HW only for the first station interface or adhoc interface. Also, cancel the ANI timer in stop() for multi-STA scenario. And finally configure the HW beacon timers only for the first station interface. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-28ath9k: Fix incorrect GPIO LED pin for AR9485Senthil Balasubramanian
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually used for this. Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-28ath9k: use generic mac80211 LED blinking codeFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-28ath9k_htc: Fix an endian issueSujith Manoharan
The stream length/tag fields have to be in little endian format. Fixing this makes the driver work on big-endian platforms. Cc: stable@kernel.org Tested-by: raghunathan.kailasanathan@wipro.com Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25ath9k: Fix compilation warning.Vivek Natarajan
Initialize txq to avoid this warning: drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’: drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25ath9k: Cancel pll_work while disabling radio.Vivek Natarajan
pll_work should be cancelled on full_sleep or it may cause redundant chip reset. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25ath9k_hw: Fix pcie_serdes setting for AR9485 1.1 version.Vivek Natarajan
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25mac80211: make tx() operation return voidJohannes Berg
The return value of the tx operation is commonly misused by drivers, leading to errors. All drivers will drop frames if they fail to TX the frame, and they must also properly manage the queues (if they didn't, mac80211 would already warn). Removing the ability for drivers to return a BUSY value also allows significant cleanups of the TX TX handling code in mac80211. Note that this also fixes a bug in ath9k_htc, the old "return -1" there was wrong. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k] Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00] Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi] Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25carl9170: add Airlive X.USB a/b/g/n USBIDJan Puk
"AirLive X.USB now works perfectly under a Linux environment!" Cc: <stable@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25ath9k: correct ath9k_hw_set_interruptsStanislaw Gruszka
Commit 4df3071ebd92ef7115b409da64d0eb405d24a631 "ath9k_hw: optimize interrupt mask changes", changed ath9k_hw_set_interrupts function to enable interrupts regardless of function argument, what could possibly be wrong. Correct that behaviour and check "ints" arguments before enabling interrupts, also disable interrupts if ints do not have ATH9K_INT_GLOBAL flag set. Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23mac80211: rename RX_FLAG_TSFTJohannes Berg
The flag isn't very descriptive -- the intention is that the driver provides a TSF timestamp at the beginning of the MPDU -- make that clearer by renaming the flag to RX_FLAG_MACTIME_MPDU. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Fix error path in URB allocationSujith Manoharan
ath9k_hif_usb_alloc_urbs() takes care of freeing all the allocated URBs for the various endpoints when an error occurs. Calling ath9k_hif_usb_dealloc_urbs() would cause a panic since the URBs have already been freed. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Add debug code to print endpoint mappingSujith Manoharan
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Fix RX filtersSujith Manoharan
Add ATH9K_RX_FILTER_UNCOMP_BA_BAR and ATH9K_RX_FILTER_PSPOLL when mac80211 requires it. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Fix host RX initializationSujith Manoharan
There is no need to set the BSSID mask or opmode when initializing RX, they would be set correctly in the HW reset routine. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Fix TBTT calculation for IBSS modeSujith Manoharan
The target beacon transmission time has to be synced with the HW TSF when configuring beacon timers in Adhoc mode. Failing to do this would cause erroneous beacon transmission, for example, on completion of a scan run to check for IBSS merges. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Configure beacon timers in AP modeSujith Manoharan
Handle multi-interface situations by checking if AP interfaces are already present. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Add ANI for AP modeSujith Manoharan
The time granularity for the ANI task is different for AP and station mode. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Calculate and set the HW opmodeSujith Manoharan
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Allow AP interface to be createdSujith Manoharan
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Maintain individual counters for interfacesSujith Manoharan
This is required for allowing only one IBSS interface to be configured. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-23ath9k_htc: Protect ampdu_action with a mutexSujith Manoharan
This is required when issuing commands to the firmware. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.46.0) at 2025-08-17 16:35:07 +0000