| Age | Commit message (Collapse) | Author |
|---|
|
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
USB: ohci-at91: change maximum number of ports
USB: ohci-at91: rework and fix initialization
ARM: at91/dts: USB host vbus is active low
ARM: at91/USB host: specify and handle properly vbus_pin_active_low
USB: ohci-at91: fix vbus_pin_active_low handling
ARM: at91/at91sam9x5: add clkdev entries for DMA controllers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into fixes
* 'for-3.4/fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
|
|
ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain
"halt()" function. Use safe_halt() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.
This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.
This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.
Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA mapping branch from Marek Szyprowski:
"Short summary for the whole series:
A few limitations have been identified in the current dma-mapping
design and its implementations for various architectures. There exist
more than one function for allocating and freeing the buffers:
currently these 3 are used dma_{alloc, free}_coherent,
dma_{alloc,free}_writecombine, dma_{alloc,free}_noncoherent.
For most of the systems these calls are almost equivalent and can be
interchanged. For others, especially the truly non-coherent ones
(like ARM), the difference can be easily noticed in overall driver
performance. Sadly not all architectures provide implementations for
all of them, so the drivers might need to be adapted and cannot be
easily shared between different architectures. The provided patches
unify all these functions and hide the differences under the already
existing dma attributes concept. The thread with more references is
available here:
http://www.spinics.net/lists/linux-sh/msg09777.html
These patches are also a prerequisite for unifying DMA-mapping
implementation on ARM architecture with the common one provided by
dma_map_ops structure and extending it with IOMMU support. More
information is available in the following thread:
http://thread.gmane.org/gmane.linux.kernel.cross-arch/12819
More works on dma-mapping framework are planned, especially in the
area of buffer sharing and managing the shared mappings (together with
the recently introduced dma_buf interface: commit d15bd7ee445d
"dma-buf: Introduce dma buffer sharing mechanism").
The patches in the current set introduce a new alloc/free methods
(with support for memory attributes) in dma_map_ops structure, which
will later replace dma_alloc_coherent and dma_alloc_writecombine
functions."
People finally started piping up with support for merging this, so I'm
merging it as the last of the pending stuff from the merge window.
Looks like pohmelfs is going to wait for 3.5 and more external support
for merging.
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
common: DMA-mapping: add NON-CONSISTENT attribute
common: DMA-mapping: add WRITE_COMBINE attribute
common: dma-mapping: introduce mmap method
common: dma-mapping: remove old alloc_coherent and free_coherent methods
Hexagon: adapt for dma_map_ops changes
Unicore32: adapt for dma_map_ops changes
Microblaze: adapt for dma_map_ops changes
SH: adapt for dma_map_ops changes
Alpha: adapt for dma_map_ops changes
SPARC: adapt for dma_map_ops changes
PowerPC: adapt for dma_map_ops changes
MIPS: adapt for dma_map_ops changes
X86 & IA64: adapt for dma_map_ops changes
common: dma-mapping: introduce generic alloc() and free() methods
|
|
In commit (bfab27a stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modified from original patch from Chris.
The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.
This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.
Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 7d26bb103c4 "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Patch series that hopefully fixes races between the freezer and
request_firmware() and request_firmware_nowait() for good, with two
cleanups from Stephen Boyd on top.
- Runtime PM fix from Alan Stern preventing tasks from getting stuck
indefinitely in the runtime PM wait queue.
- Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
* tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: add pm_qos_update_request_timeout() API
firmware_class: Move request_firmware_nowait() to workqueues
firmware_class: Reorganize fw_create_instance()
PM / Sleep: Mitigate race between the freezer and request_firmware()
PM / Sleep: Move disabling of usermode helpers to the freezer
PM / Hibernate: Disable usermode helpers right before freezing tasks
firmware_class: Do not warn that system is not ready from async loads
firmware_class: Split _request_firmware() into three functions, v2
firmware_class: Rework usermodehelper check
PM / Runtime: don't forget to wake up waitqueue on failure
|
|
When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull a single regmap fix from Mark Brown:
"A simple bug that's been lurking for a while but not terribly visible
since a high proportion of chips have no register 0 so the normal
failure is that we end up doing a bit of extra I/O."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Fix register default look-up in sync
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Remove non-existent parameter from fixed-helper.c kernel doc
regulator: Fix setting new voltage in s5m8767_set_voltage
regulator: fix sysfs name collision between dummy and fixed dummy regulator
regulator: Fix deadlock on removal of regulators with supplies
regulator: Fix comments in include/linux/regulator/machine.h
regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable
regulator: Fix setting low power mode for wm831x aldo
regulator: Return microamps in wm8350_isink_get_current
regulator: wm8350: Fix the logic to choose best current limit setting
regulator: wm831x-isink: Fix the logic to choose best current limit setting
regulator: wm831x-dcdc: Fix the logic to choose best current limit setting
regulator: anatop: patching to device-tree property "reg".
regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting
regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable
regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
regulator: Fix set and get current limit for wm831x_buckv
regulator: tps6586x: Fix list minimal voltage setting for LDO0
|
|
This fixes the CPUFREQ dependency for regarding EXYNOS SoCs
such as EXYNOS4210, EXYNOS4X12 and EXYNOS5250. Its cpufreq
driver should be built with selection of SoC arch part.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: Call restore_sched_clock_state() only after %gs is initialized
x86: Use -mno-avx when available
x86: Remove the ancient and deprecated disable_hlt() and enable_hlt() facility
x86: Preserve lazy irq disable semantics in fixup_irqs()
|
|
Compilation error in case of non-DT configuration without this
of.h header file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
Change number of ports to 3 for newer SoCs. Modify pdata structure
and ohci-at91 code that was dealing with ports information and check
of port indexes.
Several coding style errors have been addresses as the patch was touching
affected lines of code and was producing errors while run through
checkpatch.pl.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
The DT information are filled in a pdata structure and then passed on
to the usual check code of the probe function. Thus we do not need to
redo the gpio checking and irq configuration in the DT-related code.
On the other hand, we setup GPIO direction in driver for vbus and
overcurrent. It will be useful when moving to pinctrl subsystem.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
|
|
The information is not properly taken into account
for {get|set}_power() functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org> [3.2+]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon patches from Guenter Roeck:
- Fix crash in ad7314 driver
- Add support for AMD Trinity CPUs to k10temp driver
- Fix __initdata/__initconst mixup in w83627ehf driver
- Fix runtime warnings in acpi_power_meter and max6639 drivers
- Fix build warnings in adm1031, f75375s, sht15, and gpio-fan drivers
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ad7314) Adds missing spi_dev initialization
hwmon: (k10temp) Add support for AMD Trinity CPUs
hwmon: (w83627ehf) mark const init data with __initconst instead of __initdata
hwmon: (acpi_power_meter) fix lockdep spew due to non-static lock class
hwmon: (adm1031) Fix compiler warning
hwmon: (f75375s) Fix warning message seen in some configurations
hwmon: (max6639) Convert to dev_pm_ops
hwmon: (sht15) Fix Kconfig dependencies
hwmon: (gpio-fan) Fix Kconfig dependencies
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull MCE fixlet from Borislav Petkov:
"One fix which makes MCE decoding much more "liberal" wrt families."
* tag 'mce-fix-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
MCE, AMD: Drop too granulary family model checks
|
|
Pull assorted md fixes from Neil Brown:
- some RAID levels didn't clear up properly if md_integrity_register
failed
- a 'check' of RAID5/RAID6 doesn't actually read any data since a
recent patch - so fix that (and mark for -stable)
- a couple of other minor bugs.
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/raid1,raid10: don't compare excess byte during consistency check.
md/raid5: Fix a bug about judging if the operation is syncing or replacing
md/raid1:Remove unnecessary rcu_dereference(conf->mirrors[i].rdev).
md: Avoid OOPS when reshaping raid1 to raid0
md/raid5: fix handling of bad blocks during recovery.
md/raid1: If md_integrity_register() failed,run() must free the mem
md/raid0: If md_integrity_register() fails, raid0_run() must free the mem.
md/linear: If md_integrity_register() fails, linear_run() must free the mem.
|
|
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
|
|
Pull Sparc fixes from David Miller:
"One build regression and one serial probe regression fix on sparc."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
serial/sunzilog: fix keyboard on SUN SPARCstation
sparc: pgtable_64: change include order
|
|
This reverts commit d06221c0617ab6d0bc41c4980cefdd9c8cc9a1c1.
It turns out to trigger the "BUG_ON(!PageCompound(page))" in kfree(),
apparently because the code ends up trying to free somethng that was
never kmalloced in the first place.
BenH points out that the patch was untested and wasn't meant to go into
the upstream kernel that quickly in the first place.
Backtrace:
bios_shadow
bios_shadow_prom
nv_mask
init_io
bios_shadow
nouveau_bios_init
NVReadVgaCrtc
NVSetOwner
nouveau_card_init
nouveau_load
Reported-by: Meelis Roos <mroos@linux.ee>
Requested-by: Dave Airlie <airlied@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MCA details seldom change inbetween the models of a family so don't
be too conservative and enable decoding on everything starting from
K8 onwards. Minor adjustments can come in later but most importantly,
we have some decoding infrastructure in place for upcoming models by
default.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
The keyboard on my SUN SPARCstation 5 no longer worked.
The culprint was: d4e33fac2408d37f7b52e80ca2a89f9fb482914f
("serial: Kill off NO_IRQ")
Fix up logic for no irq / irq so the keyboard works again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver was recently moved from IIO (where it worked) to hwmon (where
it doesn't.) This breakage occured because the hwmon version neglected to
correctly initialize a reference to spi_dev in its drvdata. The result is a
segfault every time the temperature is queried.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
|
|
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.
Without this fix, the link could reset and result in
a link flap.
The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes. The other
places where changes were detected previously can be removed.
Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm update from Dave Airlie:
"This pull just contains a forward of the Intel fixes from Daniel.
The only annoyance is the RC6 enable, which really should have made
-next, but since Ubuntu are shipping it I reckon its getting a good
testing now by the time 3.4 comes out.
The pull from Daniel contains his pull message to me:
"A few patches for 3.4, major part is 3 regression fixes:
- ppgtt broke hibernate on snb/ivb. Somehow our QA claims that it
still works, which is why this has not been caught earlier.
- ppgtt flails in combination with dmar. I kinda expected this one :(
- fence handling bugfix for gen2/3. Iirc this one is about a year
old, fix curtesy Chris Wilson. I've created an shockingly simple
i-g-t test to catch this in the future."
Wrt regressions I've just got a report that gmbus (newly enabled
again in 3.4) is a bit noisy. I'm looking into this atm.
Also included are the rc6 enable patches for snb from Eugeni. I
wanted to include these in the main 3.4 pull but screwed it up.
Please hit me. Imo these kind of patches really should go in
before -rc1, but in thise case rc6 has brought us tons of press and
guinea pigs^W^W testers and ubuntu is already running with it. So
I estimate a pretty small chance for this to blow up.
And some smaller things:
- two minor locking snafus
- server gt2 ivb pciid
- 2 patches to sanitize the register state left behind by the bios
some more
- 2 new quirk entries
- cs readback trick against missed IRQs from ivb also enabled on snb
- sprite fix from Jesse"
Let's see if the "enable RC6 on sandybridge" finally works and sticks.
I've been enabling it by hand (i915.i915_enable_rc6=1) for several
months on my Macbook Air, and it definitely makes a difference (and has
worked for me). But every time we enabled it before it showed some odd
hw buglet for *somebody*.
This time it's all good, I'm sure.
* 'drm-fixes-intel' of git://people.freedesktop.org/~airlied/linux:
drm/i915: treat src w & h as fixed point in sprite handling code
drm/i915: no-lvds quirk on MSI DC500
drm/i915: Add lock on drm_helper_resume_force_mode
drm/i915: don't leak struct_mutex lock on ppgtt init failures
drm/i915: disable ppgtt on snb when dmar is enabled
drm/i915: add Ivy Bridge GT2 Server entries
drm/i915: properly clear SSC1 bit in the pch refclock init code
drm/i915: apply CS reg readback trick against missed IRQ on snb
drm/i915: quirk away broken OpRegion VBT
drm/i915: enable plain RC6 on Sandy Bridge by default
drm/i915: allow to select rc6 modes via kernel parameter
drm/i915: Mark untiled BLT commands as fenced on gen2/3
drm/i915: properly restore the ppgtt page directory on resume
drm/i915: Sanitize BIOS debugging bits from PIPECONF
|
