From 3f8a7fabd60e83eb2fb7add00d353d455c0e7a78 Mon Sep 17 00:00:00 2001 From: Johan Rudholm Date: Mon, 28 Jan 2013 15:08:24 +0100 Subject: mmc: sd: Simplify by using mmc_host_uhs Signed-off-by: Johan Rudholm Acked-by: Ulf Hansson Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 74972c241dff..937363948079 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -444,8 +444,7 @@ static void sd_update_bus_speed_mode(struct mmc_card *card) * If the host doesn't support any of the UHS-I modes, fallback on * default speed. */ - if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | - MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50))) { + if (!mmc_host_uhs(card->host)) { card->sd_bus_speed = 0; return; } @@ -736,8 +735,7 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) * If the host supports one of UHS-I modes, request the card * to switch to 1.8V signaling level. */ - if (host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | - MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50)) + if (mmc_host_uhs(host)) ocr |= SD_OCR_S18R; /* -- cgit v1.2.3 From 567c89032cfdda8047562abe450947ac01f2d3c7 Mon Sep 17 00:00:00 2001 From: Johan Rudholm Date: Mon, 28 Jan 2013 15:08:27 +0100 Subject: mmc: core: Break out start_signal_voltage_switch Allow callers to access the start_signal_voltage_switch host_ops member without going through any cmd11 logic. This is mostly a preparation for the following signal voltage switch patch. Also, reset ios.signal_voltage to its original value if start_signal_voltage_switch fails. Signed-off-by: Johan Rudholm Acked-by: Ulf Hansson Tested-by: Wei WANG Signed-off-by: Chris Ball --- drivers/mmc/core/core.c | 35 +++++++++++++++++++++++------------ drivers/mmc/core/core.h | 4 ++-- drivers/mmc/core/mmc.c | 8 ++++---- drivers/mmc/core/sd.c | 2 +- drivers/mmc/core/sdio.c | 3 +-- 5 files changed, 31 insertions(+), 21 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 789056fbfc93..bb794c784597 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1317,7 +1317,26 @@ u32 mmc_select_voltage(struct mmc_host *host, u32 ocr) return ocr; } -int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11) +int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) +{ + int err = 0; + int old_signal_voltage = host->ios.signal_voltage; + + host->ios.signal_voltage = signal_voltage; + if (host->ops->start_signal_voltage_switch) { + mmc_host_clk_hold(host); + err = host->ops->start_signal_voltage_switch(host, &host->ios); + mmc_host_clk_release(host); + } + + if (err) + host->ios.signal_voltage = old_signal_voltage; + + return err; + +} + +int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) { struct mmc_command cmd = {0}; int err = 0; @@ -1328,7 +1347,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11 * Send CMD11 only if the request is to switch the card to * 1.8V signalling. */ - if ((signal_voltage != MMC_SIGNAL_VOLTAGE_330) && cmd11) { + if (signal_voltage != MMC_SIGNAL_VOLTAGE_330) { cmd.opcode = SD_SWITCH_VOLTAGE; cmd.arg = 0; cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; @@ -1341,15 +1360,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, bool cmd11 return -EIO; } - host->ios.signal_voltage = signal_voltage; - - if (host->ops->start_signal_voltage_switch) { - mmc_host_clk_hold(host); - err = host->ops->start_signal_voltage_switch(host, &host->ios); - mmc_host_clk_release(host); - } - - return err; + return __mmc_set_signal_voltage(host, signal_voltage); } /* @@ -1412,7 +1423,7 @@ static void mmc_power_up(struct mmc_host *host) mmc_set_ios(host); /* Set signal voltage to 3.3V */ - mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false); + __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330); /* * This delay should be sufficient to allow the power supply diff --git a/drivers/mmc/core/core.h b/drivers/mmc/core/core.h index 9007de74d8a9..b9f18a2a8874 100644 --- a/drivers/mmc/core/core.h +++ b/drivers/mmc/core/core.h @@ -40,8 +40,8 @@ void mmc_set_ungated(struct mmc_host *host); void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode); void mmc_set_bus_width(struct mmc_host *host, unsigned int width); u32 mmc_select_voltage(struct mmc_host *host, u32 ocr); -int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, - bool cmd11); +int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage); +int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage); void mmc_set_timing(struct mmc_host *host, unsigned int timing); void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type); void mmc_power_off(struct mmc_host *host); diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c index 0d7a9795a6da..8a3ad602a877 100644 --- a/drivers/mmc/core/mmc.c +++ b/drivers/mmc/core/mmc.c @@ -769,11 +769,11 @@ static int mmc_select_hs200(struct mmc_card *card) if (card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_2V && host->caps2 & MMC_CAP2_HS200_1_2V_SDR) - err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120, 0); + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120); if (err && card->ext_csd.card_type & EXT_CSD_CARD_TYPE_SDR_1_8V && host->caps2 & MMC_CAP2_HS200_1_8V_SDR) - err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, 0); + err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); /* If fails try again during next card power cycle */ if (err) @@ -1221,8 +1221,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr, * WARNING: eMMC rules are NOT the same as SD DDR */ if (ddr == MMC_1_2V_DDR_MODE) { - err = mmc_set_signal_voltage(host, - MMC_SIGNAL_VOLTAGE_120, 0); + err = __mmc_set_signal_voltage(host, + MMC_SIGNAL_VOLTAGE_120); if (err) goto err; } diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 937363948079..9a59fcd55a75 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -757,7 +757,7 @@ try_again: */ if (!mmc_host_is_spi(host) && rocr && ((*rocr & 0x41000000) == 0x41000000)) { - err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, true); + err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); if (err) { ocr &= ~SD_OCR_S18R; goto try_again; diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c index 3a64933466b8..1a726aef211d 100644 --- a/drivers/mmc/core/sdio.c +++ b/drivers/mmc/core/sdio.c @@ -647,8 +647,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr, * it. */ if ((ocr & R4_18V_PRESENT) && mmc_host_uhs(host)) { - err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180, - true); + err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); if (err) { ocr &= ~R4_18V_PRESENT; host->ocr &= ~R4_18V_PRESENT; -- cgit v1.2.3 From 0797e5f1453b2bedc08bbcbea0ea4fbe20350823 Mon Sep 17 00:00:00 2001 From: Johan Rudholm Date: Mon, 28 Jan 2013 15:08:28 +0100 Subject: mmc: core: Fixup signal voltage switch When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the clock should be gated for 5 ms during the step. After enabling the clock, the host should wait for at least 1 ms before checking for failure. Failure by the card to switch is indicated by dat[0:3] being pulled low. The host should check for this condition and power-cycle the card if failure is indicated. Add a retry mechanism for the SDIO case. If the voltage switch fails repeatedly, give up and continue the initialization using the original voltage. This patch places a couple of requirements on the host driver: 1) mmc_set_ios with ios.clock = 0 must gate the clock 2) mmc_power_off must actually cut the power to the card 3) The card_busy host_ops member must be implemented if these requirements are not fulfilled, the 1.8V signal voltage switch will still be attempted but may not be successful. Signed-off-by: Johan Rudholm Signed-off-by: Kevin Liu Acked-by: Ulf Hansson Tested-by: Wei WANG Signed-off-by: Chris Ball --- drivers/mmc/core/core.c | 83 +++++++++++++++++++++++++++++++++++++++++++------ drivers/mmc/core/sd.c | 21 ++++++++++--- drivers/mmc/core/sdio.c | 20 ++++++++++-- 3 files changed, 107 insertions(+), 17 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index bb794c784597..e41badbf9b50 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1340,6 +1340,7 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) { struct mmc_command cmd = {0}; int err = 0; + u32 clock; BUG_ON(!host); @@ -1347,20 +1348,82 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage) * Send CMD11 only if the request is to switch the card to * 1.8V signalling. */ - if (signal_voltage != MMC_SIGNAL_VOLTAGE_330) { - cmd.opcode = SD_SWITCH_VOLTAGE; - cmd.arg = 0; - cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; + if (signal_voltage == MMC_SIGNAL_VOLTAGE_330) + return __mmc_set_signal_voltage(host, signal_voltage); - err = mmc_wait_for_cmd(host, &cmd, 0); - if (err) - return err; + /* + * If we cannot switch voltages, return failure so the caller + * can continue without UHS mode + */ + if (!host->ops->start_signal_voltage_switch) + return -EPERM; + if (!host->ops->card_busy) + pr_warning("%s: cannot verify signal voltage switch\n", + mmc_hostname(host)); + + cmd.opcode = SD_SWITCH_VOLTAGE; + cmd.arg = 0; + cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; + + err = mmc_wait_for_cmd(host, &cmd, 0); + if (err) + return err; - if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) - return -EIO; + if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) + return -EIO; + + mmc_host_clk_hold(host); + /* + * The card should drive cmd and dat[0:3] low immediately + * after the response of cmd11, but wait 1 ms to be sure + */ + mmc_delay(1); + if (host->ops->card_busy && !host->ops->card_busy(host)) { + err = -EAGAIN; + goto power_cycle; } + /* + * During a signal voltage level switch, the clock must be gated + * for 5 ms according to the SD spec + */ + clock = host->ios.clock; + host->ios.clock = 0; + mmc_set_ios(host); - return __mmc_set_signal_voltage(host, signal_voltage); + if (__mmc_set_signal_voltage(host, signal_voltage)) { + /* + * Voltages may not have been switched, but we've already + * sent CMD11, so a power cycle is required anyway + */ + err = -EAGAIN; + goto power_cycle; + } + + /* Keep clock gated for at least 5 ms */ + mmc_delay(5); + host->ios.clock = clock; + mmc_set_ios(host); + + /* Wait for at least 1 ms according to spec */ + mmc_delay(1); + + /* + * Failure to switch is indicated by the card holding + * dat[0:3] low + */ + if (host->ops->card_busy && host->ops->card_busy(host)) + err = -EAGAIN; + +power_cycle: + if (err) { + pr_debug("%s: Signal voltage switch failed, " + "power cycling card\n", mmc_hostname(host)); + mmc_power_cycle(host); + } + + mmc_host_clk_release(host); + + return err; } /* diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 9a59fcd55a75..03134b1e563c 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -712,6 +712,14 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) { int err; u32 max_current; + int retries = 10; + +try_again: + if (!retries) { + ocr &= ~SD_OCR_S18R; + pr_warning("%s: Skipping voltage switch\n", + mmc_hostname(host)); + } /* * Since we're changing the OCR value, we seem to @@ -733,9 +741,10 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) /* * If the host supports one of UHS-I modes, request the card - * to switch to 1.8V signaling level. + * to switch to 1.8V signaling level. If the card has failed + * repeatedly to switch however, skip this. */ - if (mmc_host_uhs(host)) + if (retries && mmc_host_uhs(host)) ocr |= SD_OCR_S18R; /* @@ -746,7 +755,6 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr) if (max_current > 150) ocr |= SD_OCR_XPC; -try_again: err = mmc_send_app_op_cond(host, ocr, rocr); if (err) return err; @@ -758,8 +766,11 @@ try_again: if (!mmc_host_is_spi(host) && rocr && ((*rocr & 0x41000000) == 0x41000000)) { err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); - if (err) { - ocr &= ~SD_OCR_S18R; + if (err == -EAGAIN) { + retries--; + goto try_again; + } else if (err) { + retries = 0; goto try_again; } } diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c index 1a726aef211d..aa0719a4dfd1 100644 --- a/drivers/mmc/core/sdio.c +++ b/drivers/mmc/core/sdio.c @@ -584,10 +584,19 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr, { struct mmc_card *card; int err; + int retries = 10; BUG_ON(!host); WARN_ON(!host->claimed); +try_again: + if (!retries) { + pr_warning("%s: Skipping voltage switch\n", + mmc_hostname(host)); + ocr &= ~R4_18V_PRESENT; + host->ocr &= ~R4_18V_PRESENT; + } + /* * Inform the card of the voltage */ @@ -646,9 +655,16 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr, * systems that claim 1.8v signalling in fact do not support * it. */ - if ((ocr & R4_18V_PRESENT) && mmc_host_uhs(host)) { + if (!powered_resume && (ocr & R4_18V_PRESENT) && mmc_host_uhs(host)) { err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180); - if (err) { + if (err == -EAGAIN) { + sdio_reset(host); + mmc_go_idle(host); + mmc_send_if_cond(host, host->ocr_avail); + mmc_remove_card(card); + retries--; + goto try_again; + } else if (err) { ocr &= ~R4_18V_PRESENT; host->ocr &= ~R4_18V_PRESENT; } -- cgit v1.2.3 From 52983382c74f59a3953e622d7661a24e1bc4388a Mon Sep 17 00:00:00 2001 From: Kevin Liu Date: Thu, 31 Jan 2013 11:31:37 +0800 Subject: mmc: sdhci: enhance preset value function 4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization") added preset value support and enabled it by default during sd card init. Below are the enhancements introduced by this patch: 1. In current code, preset value is enabled after setting clock finished, which means the clock is manually set by driver firstly and then suddenly switched to preset value at this point. So the first setting is useless and unnecessary. What's more, the first clock setting may differ from the preset one. The better way is enable preset value just after switch to UHS mode so the preset value can take effect immediately. So move preset value enable from mmc_sd_init_card to sdhci_set_ios which will be called during set timing. 2. In current code, preset value is disabled at the beginning of mmc_attach_sd. It's too late since low freq (400khz) should be set in mmc_power_up. So move preset value disable to sdhci_set_ios which will be called during power up. 3. host->clock and ios->drv_type should also be updated according to the preset value if it's enabled. Current code missed this. 4. This patch also introduce a quirk to disable preset value in case preset value doesn't work. This patch has been verified on sdhci-pxav3 platform with both preset enabled and disabled. Signed-off-by: Kevin Liu Reviewed-by: Ulf Hansson Signed-off-by: Chris Ball --- drivers/mmc/core/sd.c | 17 ------ drivers/mmc/host/sdhci.c | 129 ++++++++++++++++++++++++++++++++-------------- drivers/mmc/host/sdhci.h | 12 +++++ include/linux/mmc/host.h | 1 - include/linux/mmc/sdhci.h | 1 + 5 files changed, 102 insertions(+), 58 deletions(-) (limited to 'drivers/mmc/core/sd.c') diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c index 03134b1e563c..9e645e19cec6 100644 --- a/drivers/mmc/core/sd.c +++ b/drivers/mmc/core/sd.c @@ -969,16 +969,6 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr, /* Card is an ultra-high-speed card */ mmc_card_set_uhs(card); - - /* - * Since initialization is now complete, enable preset - * value registers for UHS-I cards. - */ - if (host->ops->enable_preset_value) { - mmc_host_clk_hold(card->host); - host->ops->enable_preset_value(host, true); - mmc_host_clk_release(card->host); - } } else { /* * Attempt to change to high-speed (if supported) @@ -1157,13 +1147,6 @@ int mmc_attach_sd(struct mmc_host *host) BUG_ON(!host); WARN_ON(!host->claimed); - /* Disable preset value enable if already set since last time */ - if (host->ops->enable_preset_value) { - mmc_host_clk_hold(host); - host->ops->enable_preset_value(host, false); - mmc_host_clk_release(host); - } - err = mmc_send_app_op_cond(host, 0, &ocr); if (err) return err; diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index efb112684787..ba586ae99252 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -53,6 +53,7 @@ static void sdhci_send_command(struct sdhci_host *, struct mmc_command *); static void sdhci_finish_command(struct sdhci_host *); static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode); static void sdhci_tuning_timer(unsigned long data); +static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable); #ifdef CONFIG_PM_RUNTIME static int sdhci_runtime_pm_get(struct sdhci_host *host); @@ -1082,6 +1083,37 @@ static void sdhci_finish_command(struct sdhci_host *host) } } +static u16 sdhci_get_preset_value(struct sdhci_host *host) +{ + u16 ctrl, preset = 0; + + ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); + + switch (ctrl & SDHCI_CTRL_UHS_MASK) { + case SDHCI_CTRL_UHS_SDR12: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12); + break; + case SDHCI_CTRL_UHS_SDR25: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25); + break; + case SDHCI_CTRL_UHS_SDR50: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50); + break; + case SDHCI_CTRL_UHS_SDR104: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104); + break; + case SDHCI_CTRL_UHS_DDR50: + preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50); + break; + default: + pr_warn("%s: Invalid UHS-I mode selected\n", + mmc_hostname(host->mmc)); + preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12); + break; + } + return preset; +} + static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock) { int div = 0; /* Initialized for compiler warning */ @@ -1106,35 +1138,43 @@ static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock) goto out; if (host->version >= SDHCI_SPEC_300) { + if (sdhci_readw(host, SDHCI_HOST_CONTROL2) & + SDHCI_CTRL_PRESET_VAL_ENABLE) { + u16 pre_val; + + clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL); + pre_val = sdhci_get_preset_value(host); + div = (pre_val & SDHCI_PRESET_SDCLK_FREQ_MASK) + >> SDHCI_PRESET_SDCLK_FREQ_SHIFT; + if (host->clk_mul && + (pre_val & SDHCI_PRESET_CLKGEN_SEL_MASK)) { + clk = SDHCI_PROG_CLOCK_MODE; + real_div = div + 1; + clk_mul = host->clk_mul; + } else { + real_div = max_t(int, 1, div << 1); + } + goto clock_set; + } + /* * Check if the Host Controller supports Programmable Clock * Mode. */ if (host->clk_mul) { - u16 ctrl; - + for (div = 1; div <= 1024; div++) { + if ((host->max_clk * host->clk_mul / div) + <= clock) + break; + } /* - * We need to figure out whether the Host Driver needs - * to select Programmable Clock Mode, or the value can - * be set automatically by the Host Controller based on - * the Preset Value registers. + * Set Programmable Clock Mode in the Clock + * Control register. */ - ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); - if (!(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) { - for (div = 1; div <= 1024; div++) { - if (((host->max_clk * host->clk_mul) / - div) <= clock) - break; - } - /* - * Set Programmable Clock Mode in the Clock - * Control register. - */ - clk = SDHCI_PROG_CLOCK_MODE; - real_div = div; - clk_mul = host->clk_mul; - div--; - } + clk = SDHCI_PROG_CLOCK_MODE; + real_div = div; + clk_mul = host->clk_mul; + div--; } else { /* Version 3.00 divisors must be a multiple of 2. */ if (host->max_clk <= clock) @@ -1159,6 +1199,7 @@ static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock) div >>= 1; } +clock_set: if (real_div) host->mmc->actual_clock = (host->max_clk * clk_mul) / real_div; @@ -1376,6 +1417,10 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios) sdhci_reinit(host); } + if (host->version >= SDHCI_SPEC_300 && + (ios->power_mode == MMC_POWER_UP)) + sdhci_enable_preset_value(host, false); + sdhci_set_clock(host, ios->clock); if (ios->power_mode == MMC_POWER_OFF) @@ -1496,6 +1541,20 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios) sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); } + if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) && + ((ios->timing == MMC_TIMING_UHS_SDR12) || + (ios->timing == MMC_TIMING_UHS_SDR25) || + (ios->timing == MMC_TIMING_UHS_SDR50) || + (ios->timing == MMC_TIMING_UHS_SDR104) || + (ios->timing == MMC_TIMING_UHS_DDR50))) { + u16 preset; + + sdhci_enable_preset_value(host, true); + preset = sdhci_get_preset_value(host); + ios->drv_type = (preset & SDHCI_PRESET_DRV_MASK) + >> SDHCI_PRESET_DRV_SHIFT; + } + /* Re-enable SD Clock */ sdhci_update_clock(host); } else @@ -1925,17 +1984,15 @@ out: return err; } -static void sdhci_do_enable_preset_value(struct sdhci_host *host, bool enable) + +static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable) { u16 ctrl; - unsigned long flags; /* Host Controller v3.00 defines preset value registers */ if (host->version < SDHCI_SPEC_300) return; - spin_lock_irqsave(&host->lock, flags); - ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2); /* @@ -1951,17 +2008,6 @@ static void sdhci_do_enable_preset_value(struct sdhci_host *host, bool enable) sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2); host->flags &= ~SDHCI_PV_ENABLED; } - - spin_unlock_irqrestore(&host->lock, flags); -} - -static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable) -{ - struct sdhci_host *host = mmc_priv(mmc); - - sdhci_runtime_pm_get(host); - sdhci_do_enable_preset_value(host, enable); - sdhci_runtime_pm_put(host); } static void sdhci_card_event(struct mmc_host *mmc) @@ -1997,7 +2043,6 @@ static const struct mmc_host_ops sdhci_ops = { .enable_sdio_irq = sdhci_enable_sdio_irq, .start_signal_voltage_switch = sdhci_start_signal_voltage_switch, .execute_tuning = sdhci_execute_tuning, - .enable_preset_value = sdhci_enable_preset_value, .card_event = sdhci_card_event, .card_busy = sdhci_card_busy, }; @@ -2591,8 +2636,12 @@ int sdhci_runtime_resume_host(struct sdhci_host *host) sdhci_do_set_ios(host, &host->mmc->ios); sdhci_do_start_signal_voltage_switch(host, &host->mmc->ios); - if (host_flags & SDHCI_PV_ENABLED) - sdhci_do_enable_preset_value(host, true); + if ((host_flags & SDHCI_PV_ENABLED) && + !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) { + spin_lock_irqsave(&host->lock, flags); + sdhci_enable_preset_value(host, true); + spin_unlock_irqrestore(&host->lock, flags); + } /* Set the re-tuning expiration flag */ if (host->flags & SDHCI_USING_RETUNING_TIMER) diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index c8d11b904a40..379e09d9f3c1 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -229,6 +229,18 @@ /* 60-FB reserved */ +#define SDHCI_PRESET_FOR_SDR12 0x66 +#define SDHCI_PRESET_FOR_SDR25 0x68 +#define SDHCI_PRESET_FOR_SDR50 0x6A +#define SDHCI_PRESET_FOR_SDR104 0x6C +#define SDHCI_PRESET_FOR_DDR50 0x6E +#define SDHCI_PRESET_DRV_MASK 0xC000 +#define SDHCI_PRESET_DRV_SHIFT 14 +#define SDHCI_PRESET_CLKGEN_SEL_MASK 0x400 +#define SDHCI_PRESET_CLKGEN_SEL_SHIFT 10 +#define SDHCI_PRESET_SDCLK_FREQ_MASK 0x3FF +#define SDHCI_PRESET_SDCLK_FREQ_SHIFT 0 + #define SDHCI_SLOT_INT_STATUS 0xFC #define SDHCI_HOST_VERSION 0xFE diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 0373b0a6daac..6c235e03de29 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -136,7 +136,6 @@ struct mmc_host_ops { /* The tuning command opcode value is different for SD and eMMC cards */ int (*execute_tuning)(struct mmc_host *host, u32 opcode); - void (*enable_preset_value)(struct mmc_host *host, bool enable); int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv); void (*hw_reset)(struct mmc_host *host); void (*card_event)(struct mmc_host *host); diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h index 4bbc3301fbbf..b838ffc49e4a 100644 --- a/include/linux/mmc/sdhci.h +++ b/include/linux/mmc/sdhci.h @@ -94,6 +94,7 @@ struct sdhci_host { #define SDHCI_QUIRK2_HOST_NO_CMD23 (1<<1) /* The system physically doesn't support 1.8v, even if the host does */ #define SDHCI_QUIRK2_NO_1_8_V (1<<2) +#define SDHCI_QUIRK2_PRESET_VALUE_BROKEN (1<<3) int irq; /* Device IRQ */ void __iomem *ioaddr; /* Mapped address */ -- cgit v1.2.3