From 1241f29fa3c6fa95f20e3e77452f8d6d60deae7a Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 06:25:42 +0000
Subject: e1000e: SerDes autoneg flow control

Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.

Remove inapplicable comment in defines.h

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 02a12b69555f..20735327a7a0 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -241,9 +241,9 @@
 #define E1000_CTRL_VME      0x40000000  /* IEEE VLAN mode enable */
 #define E1000_CTRL_PHY_RST  0x80000000  /* PHY Reset */
 
-/* Bit definitions for the Management Data IO (MDIO) and Management Data
- * Clock (MDC) pins in the Device Control Register.
- */
+#define E1000_PCS_LCTL_FORCE_FCTRL	0x80
+
+#define E1000_PCS_LSTS_AN_COMPLETE	0x10000
 
 /* Device Status */
 #define E1000_STATUS_FD         0x00000001      /* Full duplex.0=half,1=full */
-- 
cgit v1.2.3


From 1cc7a3a14fa60f31ca4ff69f0dd31f369e0a51c2 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 9 Jan 2013 08:15:42 +0000
Subject: e1000e: Invalid Image CSUM bit changed for I217

On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs.  When validating the EEPROM checksum,
check the appropriate bit on different devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  4 ++++
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 29 +++++++++++++++++++++--------
 2 files changed, 25 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 20735327a7a0..7326ea2fef8f 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -639,6 +639,10 @@
 /* NVM Word Offsets */
 #define NVM_COMPAT                 0x0003
 #define NVM_ID_LED_SETTINGS        0x0004
+#define NVM_FUTURE_INIT_WORD1      0x0019
+#define NVM_COMPAT_VALID_CSUM      0x0001
+#define NVM_FUTURE_INIT_WORD1_VALID_CSUM	0x0040
+
 #define NVM_INIT_CONTROL2_REG      0x000F
 #define NVM_INIT_CONTROL3_PORT_B   0x0014
 #define NVM_INIT_3GIO_3            0x001A
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 976336547607..7d5f6b7856e6 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -2949,19 +2949,32 @@ static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw)
 {
 	s32 ret_val;
 	u16 data;
+	u16 word;
+	u16 valid_csum_mask;
 
-	/* Read 0x19 and check bit 6.  If this bit is 0, the checksum
-	 * needs to be fixed.  This bit is an indication that the NVM
-	 * was prepared by OEM software and did not calculate the
-	 * checksum...a likely scenario.
+	/* Read NVM and check Invalid Image CSUM bit.  If this bit is 0,
+	 * the checksum needs to be fixed.  This bit is an indication that
+	 * the NVM was prepared by OEM software and did not calculate
+	 * the checksum...a likely scenario.
 	 */
-	ret_val = e1000_read_nvm(hw, 0x19, 1, &data);
+	switch (hw->mac.type) {
+	case e1000_pch_lpt:
+		word = NVM_COMPAT;
+		valid_csum_mask = NVM_COMPAT_VALID_CSUM;
+		break;
+	default:
+		word = NVM_FUTURE_INIT_WORD1;
+		valid_csum_mask = NVM_FUTURE_INIT_WORD1_VALID_CSUM;
+		break;
+	}
+
+	ret_val = e1000_read_nvm(hw, word, 1, &data);
 	if (ret_val)
 		return ret_val;
 
-	if (!(data & 0x40)) {
-		data |= 0x40;
-		ret_val = e1000_write_nvm(hw, 0x19, 1, &data);
+	if (!(data & valid_csum_mask)) {
+		data |= valid_csum_mask;
+		ret_val = e1000_write_nvm(hw, word, 1, &data);
 		if (ret_val)
 			return ret_val;
 		ret_val = e1000e_update_nvm_checksum(hw);
-- 
cgit v1.2.3


From 203e41514a557b71c4c42b4bb2912b56fa0c2fdc Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 5 Dec 2012 08:40:59 +0000
Subject: e1000e: add ethtool .get_eee/.set_eee

Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  30 +++++++
 drivers/net/ethernet/intel/e1000e/e1000.h   |   1 +
 drivers/net/ethernet/intel/e1000e/ethtool.c | 134 ++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/hw.h      |   1 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c |  24 +----
 5 files changed, 167 insertions(+), 23 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 7326ea2fef8f..3041a54e3a61 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -383,6 +383,9 @@
 
 #define E1000_KABGTXD_BGSQLBIAS           0x00050000
 
+/* Low Power IDLE Control */
+#define E1000_LPIC_LPIET_SHIFT		24	/* Low Power Idle Entry Time */
+
 /* PBA constants */
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
@@ -799,6 +802,33 @@
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 
+/* PHY Low Power Idle Control */
+#define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
+#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
+#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
+
+/* Extended Management Interface (EMI) Registers */
+#define I82579_EMI_ADDR		0x10
+#define I82579_EMI_DATA		0x11
+#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
+#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
+#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_CAPABILITY	0x0410	/* IEEE MMD Register 3.20 */
+#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
+#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
+#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
+#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
+#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
+
+#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
+#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
 
 #define PHY_PAGE_SHIFT 5
 #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 3f8bbc31795c..b89b181da7b1 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -659,6 +659,7 @@ extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern bool e1000_check_phy_82574(struct e1000_hw *hw);
+extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 2225603a8a28..636ba09ca6fb 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -35,6 +35,7 @@
 #include <linux/slab.h>
 #include <linux/delay.h>
 #include <linux/vmalloc.h>
+#include <linux/mdio.h>
 
 #include "e1000.h"
 
@@ -2050,6 +2051,137 @@ static int e1000_get_rxnfc(struct net_device *netdev,
 	}
 }
 
+static int e1000e_get_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	u16 cap_addr, adv_addr, lpa_addr, pcs_stat_addr, phy_data, lpi_ctrl;
+	u32 status, ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	switch (hw->phy.type) {
+	case e1000_phy_82579:
+		cap_addr = I82579_EEE_CAPABILITY;
+		adv_addr = I82579_EEE_ADVERTISEMENT;
+		lpa_addr = I82579_EEE_LP_ABILITY;
+		pcs_stat_addr = I82579_EEE_PCS_STATUS;
+		break;
+	case e1000_phy_i217:
+		cap_addr = I217_EEE_CAPABILITY;
+		adv_addr = I217_EEE_ADVERTISEMENT;
+		lpa_addr = I217_EEE_LP_ABILITY;
+		pcs_stat_addr = I217_EEE_PCS_STATUS;
+		break;
+	default:
+		return -EOPNOTSUPP;
+	}
+
+	ret_val = hw->phy.ops.acquire(hw);
+	if (ret_val)
+		return -EBUSY;
+
+	/* EEE Capability */
+	ret_val = e1000_read_emi_reg_locked(hw, cap_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->supported = mmd_eee_cap_to_ethtool_sup_t(phy_data);
+
+	/* EEE Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, adv_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE Link Partner Advertised */
+	ret_val = e1000_read_emi_reg_locked(hw, lpa_addr, &phy_data);
+	if (ret_val)
+		goto release;
+	edata->lp_advertised = mmd_eee_adv_to_ethtool_adv_t(phy_data);
+
+	/* EEE PCS Status */
+	ret_val = e1000_read_emi_reg_locked(hw, pcs_stat_addr, &phy_data);
+	if (hw->phy.type == e1000_phy_82579)
+		phy_data <<= 8;
+
+release:
+	hw->phy.ops.release(hw);
+	if (ret_val)
+		return -ENODATA;
+
+	e1e_rphy(hw, I82579_LPI_CTRL, &lpi_ctrl);
+	status = er32(STATUS);
+
+	/* Result of the EEE auto negotiation - there is no register that
+	 * has the status of the EEE negotiation so do a best-guess based
+	 * on whether both Tx and Rx LPI indications have been received or
+	 * base it on the link speed, the EEE advertised speeds on both ends
+	 * and the speeds on which EEE is enabled locally.
+	 */
+	if (((phy_data & E1000_EEE_TX_LPI_RCVD) &&
+	     (phy_data & E1000_EEE_RX_LPI_RCVD)) ||
+	    ((status & E1000_STATUS_SPEED_100) &&
+	     (edata->advertised & ADVERTISED_100baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_100baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_100_ENABLE)) ||
+	    ((status & E1000_STATUS_SPEED_1000) &&
+	     (edata->advertised & ADVERTISED_1000baseT_Full) &&
+	     (edata->lp_advertised & ADVERTISED_1000baseT_Full) &&
+	     (lpi_ctrl & I82579_LPI_CTRL_1000_ENABLE)))
+		edata->eee_active = true;
+
+	edata->eee_enabled = !hw->dev_spec.ich8lan.eee_disable;
+	edata->tx_lpi_enabled = true;
+	edata->tx_lpi_timer = er32(LPIC) >> E1000_LPIC_LPIET_SHIFT;
+
+	return 0;
+}
+
+static int e1000e_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct e1000_hw *hw = &adapter->hw;
+	struct ethtool_eee eee_curr;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_IS_ICH) ||
+	    !(adapter->flags2 & FLAG2_HAS_EEE))
+		return -EOPNOTSUPP;
+
+	ret_val = e1000e_get_eee(netdev, &eee_curr);
+	if (ret_val)
+		return ret_val;
+
+	if (eee_curr.advertised != edata->advertised) {
+		e_err("Setting EEE advertisement is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_enabled != edata->tx_lpi_enabled) {
+		e_err("Setting EEE tx-lpi is not supported\n");
+		return -EINVAL;
+	}
+
+	if (eee_curr.tx_lpi_timer != edata->tx_lpi_timer) {
+		e_err("Setting EEE Tx LPI timer is not supported\n");
+		return -EINVAL;
+	}
+
+	if (hw->dev_spec.ich8lan.eee_disable != !edata->eee_enabled) {
+		hw->dev_spec.ich8lan.eee_disable = !edata->eee_enabled;
+
+		/* reset the link */
+		if (netif_running(netdev))
+			e1000e_reinit_locked(adapter);
+		else
+			e1000e_reset(adapter);
+	}
+
+	return 0;
+}
+
 static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_settings		= e1000_get_settings,
 	.set_settings		= e1000_set_settings,
@@ -2078,6 +2210,8 @@ static const struct ethtool_ops e1000_ethtool_ops = {
 	.set_coalesce		= e1000_set_coalesce,
 	.get_rxnfc		= e1000_get_rxnfc,
 	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_eee		= e1000e_get_eee,
+	.set_eee		= e1000e_set_eee,
 };
 
 void e1000e_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 06239fe47db1..81afad5b80f2 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -62,6 +62,7 @@ enum e1e_registers {
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
 	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
 #define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
+	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
 	E1000_RCTL     = 0x00100, /* Rx Control - RW */
 	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
 	E1000_TXCW     = 0x00178, /* Tx Configuration Word - RW */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 051dfda75fc0..3829f7fd1d97 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -148,28 +148,6 @@
 #define HV_PM_CTRL		PHY_REG(770, 17)
 #define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
 
-/* PHY Low Power Idle Control */
-#define I82579_LPI_CTRL				PHY_REG(772, 20)
-#define I82579_LPI_CTRL_100_ENABLE		0x2000
-#define I82579_LPI_CTRL_1000_ENABLE		0x4000
-#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
-#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
-
-/* Extended Management Interface (EMI) Registers */
-#define I82579_EMI_ADDR         0x10
-#define I82579_EMI_DATA         0x11
-#define I82579_LPI_UPDATE_TIMER 0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD    0x084F	/* 82579 Mean Square Error Threshold */
-#define I82577_MSE_THRESHOLD    0x0887	/* 82577 Mean Square Error Threshold */
-#define I82579_MSE_LINK_DOWN    0x2411	/* MSE count before dropping link */
-#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
-#define I82579_EEE_LP_ABILITY	0x040F	/* IEEE MMD Register 7.61 */
-#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
-#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
-#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
-#define I217_EEE_ADVERTISEMENT  0x8001	/* IEEE MMD Register 7.60 */
-#define I217_EEE_LP_ABILITY     0x8002	/* IEEE MMD Register 7.61 */
-
 /* Intel Rapid Start Technology Support */
 #define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
 #define I217_PROXY_CTRL_AUTO_DISABLE    0x0080
@@ -829,7 +807,7 @@ static s32 __e1000_access_emi_reg_locked(struct e1000_hw *hw, u16 address,
  *
  *  Assumes the SW/FW/HW Semaphore is already acquired.
  **/
-static s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
+s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data)
 {
 	return __e1000_access_emi_reg_locked(hw, addr, data, true);
 }
-- 
cgit v1.2.3


From b67e191307a3f330525265af3e2877a74d557cbf Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Thu, 27 Dec 2012 08:32:33 +0000
Subject: e1000e: add support for hardware timestamping on some devices

On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set.  Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   |   2 +
 drivers/net/ethernet/intel/e1000e/defines.h |  14 ++
 drivers/net/ethernet/intel/e1000e/e1000.h   |  46 +++-
 drivers/net/ethernet/intel/e1000e/ethtool.c |  25 +-
 drivers/net/ethernet/intel/e1000e/hw.h      |  10 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c |   2 +
 drivers/net/ethernet/intel/e1000e/netdev.c  | 371 +++++++++++++++++++++++++++-
 7 files changed, 462 insertions(+), 8 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index c77d010d5c59..587890d2d55e 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -2044,6 +2044,7 @@ const struct e1000_info e1000_82574_info = {
 				  | FLAG_HAS_MSIX
 				  | FLAG_HAS_JUMBO_FRAMES
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT
@@ -2065,6 +2066,7 @@ const struct e1000_info e1000_82583_info = {
 	.mac			= e1000_82583,
 	.flags			= FLAG_HAS_HW_VLAN_FILTER
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_APME_IN_CTRL3
 				  | FLAG_HAS_SMART_POWER_DOWN
 				  | FLAG_HAS_AMT
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 3041a54e3a61..36f9fad19a76 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -107,6 +107,7 @@
 #define E1000_RXD_ERR_RXE       0x80    /* Rx Data Error */
 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF  /* VLAN ID is in lower 12 bits */
 
+#define E1000_RXDEXT_STATERR_TST   0x00000100	/* Time Stamp taken */
 #define E1000_RXDEXT_STATERR_CE    0x01000000
 #define E1000_RXDEXT_STATERR_SE    0x02000000
 #define E1000_RXDEXT_STATERR_SEQ   0x04000000
@@ -318,6 +319,7 @@
 #define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
 #define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
 #define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
+#define E1000_TXD_EXTCMD_TSTAMP	0x00000010 /* IEEE1588 Timestamp packet */
 
 /* Transmit Control */
 #define E1000_TCTL_EN     0x00000002    /* enable Tx */
@@ -536,6 +538,18 @@
 #define E1000_RXCW_C          0x20000000        /* Receive config */
 #define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
 
+#define E1000_TSYNCTXCTL_VALID		0x00000001 /* Tx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
+#define E1000_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
+
+#define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
+#define E1000_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_ENABLED	0x00000010 /* enable Rx timestamping */
+#define E1000_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
+
+#define E1000_TIMINCA_INCPERIOD_SHIFT	24
+#define E1000_TIMINCA_INCVALUE_MASK	0x00FFFFFF
+
 /* PCI Express Control */
 #define E1000_GCR_RXD_NO_SNOOP          0x00000001
 #define E1000_GCR_RXDSCW_NO_SNOOP       0x00000002
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index b89b181da7b1..dea9e5552966 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -41,6 +41,8 @@
 #include <linux/pci-aspm.h>
 #include <linux/crc32.h>
 #include <linux/if_vlan.h>
+#include <linux/clocksource.h>
+#include <linux/net_tstamp.h>
 
 #include "hw.h"
 
@@ -353,6 +355,7 @@ struct e1000_adapter {
 	u64 gorc_old;
 	u32 alloc_rx_buff_failed;
 	u32 rx_dma_failed;
+	u32 rx_hwtstamp_cleared;
 
 	unsigned int rx_ps_pages;
 	u16 rx_ps_bsize0;
@@ -402,6 +405,14 @@ struct e1000_adapter {
 
 	u16 tx_ring_count;
 	u16 rx_ring_count;
+
+	struct hwtstamp_config hwtstamp_config;
+	struct delayed_work systim_overflow_work;
+	struct sk_buff *tx_hwtstamp_skb;
+	struct work_struct tx_hwtstamp_work;
+	spinlock_t systim_lock;	/* protects SYSTIML/H regsters */
+	struct cyclecounter cc;
+	struct timecounter tc;
 };
 
 struct e1000_info {
@@ -416,6 +427,38 @@ struct e1000_info {
 	const struct e1000_nvm_operations *nvm_ops;
 };
 
+/* The system time is maintained by a 64-bit counter comprised of the 32-bit
+ * SYSTIMH and SYSTIML registers.  How the counter increments (and therefore
+ * its resolution) is based on the contents of the TIMINCA register - it
+ * increments every incperiod (bits 31:24) clock ticks by incvalue (bits 23:0).
+ * For the best accuracy, the incperiod should be as small as possible.  The
+ * incvalue is scaled by a factor as large as possible (while still fitting
+ * in bits 23:0) so that relatively small clock corrections can be made.
+ *
+ * As a result, a shift of INCVALUE_SHIFT_n is used to fit a value of
+ * INCVALUE_n into the TIMINCA register allowing 32+8+(24-INCVALUE_SHIFT_n)
+ * bits to count nanoseconds leaving the rest for fractional nonseconds.
+ */
+#define INCVALUE_96MHz		125
+#define INCVALUE_SHIFT_96MHz	17
+#define INCPERIOD_SHIFT_96MHz	2
+#define INCPERIOD_96MHz		(12 >> INCPERIOD_SHIFT_96MHz)
+
+#define INCVALUE_25MHz		40
+#define INCVALUE_SHIFT_25MHz	18
+#define INCPERIOD_25MHz		1
+
+/* Another drawback of scaling the incvalue by a large factor is the
+ * 64-bit SYSTIM register overflows more quickly.  This is dealt with
+ * by simply reading the clock before it overflows.
+ *
+ * Clock	ns bits	Overflows after
+ * ~~~~~~	~~~~~~~	~~~~~~~~~~~~~~~
+ * 96MHz	47-bit	2^(47-INCPERIOD_SHIFT_96MHz) / 10^9 / 3600 = 9.77 hrs
+ * 25MHz	46-bit	2^46 / 10^9 / 3600 = 19.55 hours
+ */
+#define E1000_SYSTIM_OVERFLOW_PERIOD	(HZ * 60 * 60 * 4)
+
 /* hardware capability, feature, and workaround flags */
 #define FLAG_HAS_AMT                      (1 << 0)
 #define FLAG_HAS_FLASH                    (1 << 1)
@@ -431,7 +474,7 @@ struct e1000_info {
 #define FLAG_HAS_SMART_POWER_DOWN         (1 << 11)
 #define FLAG_IS_QUAD_PORT_A               (1 << 12)
 #define FLAG_IS_QUAD_PORT                 (1 << 13)
-/* reserved bit14 */
+#define FLAG_HAS_HW_TIMESTAMP             (1 << 14)
 #define FLAG_APME_IN_WUC                  (1 << 15)
 #define FLAG_APME_IN_CTRL3                (1 << 16)
 #define FLAG_APME_CHECK_PORT_B            (1 << 17)
@@ -463,6 +506,7 @@ struct e1000_info {
 #define FLAG2_NO_DISABLE_RX               (1 << 10)
 #define FLAG2_PCIM2PCI_ARBITER_WA         (1 << 11)
 #define FLAG2_DFLT_CRC_STRIPPING          (1 << 12)
+#define FLAG2_CHECK_RX_HWTSTAMP           (1 << 13)
 
 #define E1000_RX_DESC_PS(R, i)	    \
 	(&(((union e1000_rx_desc_packet_split *)((R).desc))[i]))
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 636ba09ca6fb..f268cbcb751d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -108,6 +108,7 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("dropped_smbus", stats.mgpdc),
 	E1000_STAT("rx_dma_failed", rx_dma_failed),
 	E1000_STAT("tx_dma_failed", tx_dma_failed),
+	E1000_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
 };
 
 #define E1000_GLOBAL_STATS_LEN	ARRAY_SIZE(e1000_gstrings_stats)
@@ -2182,6 +2183,28 @@ static int e1000e_set_eee(struct net_device *netdev, struct ethtool_eee *edata)
 	return 0;
 }
 
+static int e1000e_get_ts_info(struct net_device *netdev,
+			      struct ethtool_ts_info *info)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+
+	ethtool_op_get_ts_info(netdev, info);
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return 0;
+
+	info->so_timestamping |= (SOF_TIMESTAMPING_TX_HARDWARE |
+				  SOF_TIMESTAMPING_RX_HARDWARE |
+				  SOF_TIMESTAMPING_RAW_HARDWARE);
+
+	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
+
+	info->rx_filters = ((1 << HWTSTAMP_FILTER_NONE) |
+			    (1 << HWTSTAMP_FILTER_ALL));
+
+	return 0;
+}
+
 static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_settings		= e1000_get_settings,
 	.set_settings		= e1000_set_settings,
@@ -2209,7 +2232,7 @@ static const struct ethtool_ops e1000_ethtool_ops = {
 	.get_coalesce		= e1000_get_coalesce,
 	.set_coalesce		= e1000_set_coalesce,
 	.get_rxnfc		= e1000_get_rxnfc,
-	.get_ts_info		= ethtool_op_get_ts_info,
+	.get_ts_info		= e1000e_get_ts_info,
 	.get_eee		= e1000e_get_eee,
 	.set_eee		= e1000e_set_eee,
 };
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 81afad5b80f2..8e7e80345a60 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -60,6 +60,7 @@ enum e1e_registers {
 	E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
 	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
+	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
 	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
 #define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
 	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
@@ -241,6 +242,15 @@ enum e1e_registers {
 #define E1000_PCH_RAICC(_n)	(E1000_PCH_RAICC_BASE + ((_n) * 4))
 #define E1000_CRC_OFFSET	E1000_PCH_RAICC_BASE
 	E1000_HICR      = 0x08F00, /* Host Interface Control */
+	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
+	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
+	E1000_TIMINCA   = 0x0B608, /* Increment attributes register - RW */
+	E1000_TSYNCTXCTL = 0x0B614, /* Tx Time Sync Control register - RW */
+	E1000_TXSTMPL   = 0x0B618, /* Tx timestamp value Low - RO */
+	E1000_TXSTMPH   = 0x0B61C, /* Tx timestamp value High - RO */
+	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
+	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
+	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
 };
 
 #define E1000_MAX_PHY_ADDR		4
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 3829f7fd1d97..50935ef48171 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4601,6 +4601,7 @@ const struct e1000_info e1000_pch2_info = {
 	.mac			= e1000_pch2lan,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
@@ -4620,6 +4621,7 @@ const struct e1000_info e1000_pch_lpt_info = {
 	.mac			= e1000_pch_lpt,
 	.flags			= FLAG_IS_ICH
 				  | FLAG_HAS_WOL
+				  | FLAG_HAS_HW_TIMESTAMP
 				  | FLAG_HAS_CTRLEXT_ON_LOAD
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index bf2c84cf250f..c15b7e438a44 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -487,21 +487,88 @@ static int e1000_desc_unused(struct e1000_ring *ring)
 	return ring->count + ring->next_to_clean - ring->next_to_use - 1;
 }
 
+/**
+ * e1000e_systim_to_hwtstamp - convert system time value to hw time stamp
+ * @adapter: board private structure
+ * @hwtstamps: time stamp structure to update
+ * @systim: unsigned 64bit system time value.
+ *
+ * Convert the system time value stored in the RX/TXSTMP registers into a
+ * hwtstamp which can be used by the upper level time stamping functions.
+ *
+ * The 'systim_lock' spinlock is used to protect the consistency of the
+ * system time value. This is needed because reading the 64 bit time
+ * value involves reading two 32 bit registers. The first read latches the
+ * value.
+ **/
+static void e1000e_systim_to_hwtstamp(struct e1000_adapter *adapter,
+				      struct skb_shared_hwtstamps *hwtstamps,
+				      u64 systim)
+{
+	u64 ns;
+	unsigned long flags;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	ns = timecounter_cyc2time(&adapter->tc, systim);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	memset(hwtstamps, 0, sizeof(*hwtstamps));
+	hwtstamps->hwtstamp = ns_to_ktime(ns);
+}
+
+/**
+ * e1000e_rx_hwtstamp - utility function which checks for Rx time stamp
+ * @adapter: board private structure
+ * @status: descriptor extended error and status field
+ * @skb: particular skb to include time stamp
+ *
+ * If the time stamp is valid, convert it into the timecounter ns value
+ * and store that result into the shhwtstamps structure which is passed
+ * up the network stack.
+ **/
+static void e1000e_rx_hwtstamp(struct e1000_adapter *adapter, u32 status,
+			       struct sk_buff *skb)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u64 rxstmp;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP) ||
+	    !(status & E1000_RXDEXT_STATERR_TST) ||
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID))
+		return;
+
+	/* The Rx time stamp registers contain the time stamp.  No other
+	 * received packet will be time stamped until the Rx time stamp
+	 * registers are read.  Because only one packet can be time stamped
+	 * at a time, the register values must belong to this packet and
+	 * therefore none of the other additional attributes need to be
+	 * compared.
+	 */
+	rxstmp = (u64)er32(RXSTMPL);
+	rxstmp |= (u64)er32(RXSTMPH) << 32;
+	e1000e_systim_to_hwtstamp(adapter, skb_hwtstamps(skb), rxstmp);
+
+	adapter->flags2 &= ~FLAG2_CHECK_RX_HWTSTAMP;
+}
+
 /**
  * e1000_receive_skb - helper function to handle Rx indications
  * @adapter: board private structure
- * @status: descriptor status field as written by hardware
+ * @staterr: descriptor extended error and status field as written by hardware
  * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
  * @skb: pointer to sk_buff to be indicated to stack
  **/
 static void e1000_receive_skb(struct e1000_adapter *adapter,
 			      struct net_device *netdev, struct sk_buff *skb,
-			      u8 status, __le16 vlan)
+			      u32 staterr, __le16 vlan)
 {
 	u16 tag = le16_to_cpu(vlan);
+
+	e1000e_rx_hwtstamp(adapter, staterr, skb);
+
 	skb->protocol = eth_type_trans(skb, netdev);
 
-	if (status & E1000_RXD_STAT_VP)
+	if (staterr & E1000_RXD_STAT_VP)
 		__vlan_hwaccel_put_tag(skb, tag);
 
 	napi_gro_receive(&adapter->napi, skb);
@@ -1091,6 +1158,41 @@ static void e1000_print_hw_hang(struct work_struct *work)
 		e_err("Try turning off Tx pause (flow control) via ethtool\n");
 }
 
+/**
+ * e1000e_tx_hwtstamp_work - check for Tx time stamp
+ * @work: pointer to work struct
+ *
+ * This work function polls the TSYNCTXCTL valid bit to determine when a
+ * timestamp has been taken for the current stored skb.  The timestamp must
+ * be for this skb because only one such packet is allowed in the queue.
+ */
+static void e1000e_tx_hwtstamp_work(struct work_struct *work)
+{
+	struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
+						     tx_hwtstamp_work);
+	struct e1000_hw *hw = &adapter->hw;
+
+	if (!adapter->tx_hwtstamp_skb)
+		return;
+
+	if (er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_VALID) {
+		struct skb_shared_hwtstamps shhwtstamps;
+		u64 txstmp;
+
+		txstmp = er32(TXSTMPL);
+		txstmp |= (u64)er32(TXSTMPH) << 32;
+
+		e1000e_systim_to_hwtstamp(adapter, &shhwtstamps, txstmp);
+
+		skb_tstamp_tx(adapter->tx_hwtstamp_skb, &shhwtstamps);
+		dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+		adapter->tx_hwtstamp_skb = NULL;
+	} else {
+		/* reschedule to check later */
+		schedule_work(&adapter->tx_hwtstamp_work);
+	}
+}
+
 /**
  * e1000_clean_tx_irq - Reclaim resources after transmit completes
  * @tx_ring: Tx descriptor ring
@@ -1345,8 +1447,8 @@ copydone:
 			   cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
 			adapter->rx_hdr_split++;
 
-		e1000_receive_skb(adapter, netdev, skb,
-				  staterr, rx_desc->wb.middle.vlan);
+		e1000_receive_skb(adapter, netdev, skb, staterr,
+				  rx_desc->wb.middle.vlan);
 
 next_desc:
 		rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
@@ -3303,6 +3405,159 @@ static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
 	ew32(MRQC, mrqc);
 }
 
+/**
+ * e1000e_get_base_timinca - get default SYSTIM time increment attributes
+ * @adapter: board private structure
+ * @timinca: pointer to returned time increment attributes
+ *
+ * Get attributes for incrementing the System Time Register SYSTIML/H at
+ * the default base frequency, and set the cyclecounter shift value.
+ **/
+static s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	u32 incvalue, incperiod, shift;
+
+	/* Make sure clock is enabled on I217 before checking the frequency */
+	if ((hw->mac.type == e1000_pch_lpt) &&
+	    !(er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) &&
+	    !(er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_ENABLED)) {
+		u32 fextnvm7 = er32(FEXTNVM7);
+
+		if (!(fextnvm7 & (1 << 0))) {
+			ew32(FEXTNVM7, fextnvm7 | (1 << 0));
+			e1e_flush();
+		}
+	}
+
+	switch (hw->mac.type) {
+	case e1000_pch2lan:
+	case e1000_pch_lpt:
+		/* On I217, the clock frequency is 25MHz or 96MHz as
+		 * indicated by the System Clock Frequency Indication
+		 */
+		if ((hw->mac.type != e1000_pch_lpt) ||
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
+			/* Stable 96MHz frequency */
+			incperiod = INCPERIOD_96MHz;
+			incvalue = INCVALUE_96MHz;
+			shift = INCVALUE_SHIFT_96MHz;
+			adapter->cc.shift = shift + INCPERIOD_SHIFT_96MHz;
+			break;
+		}
+		/* fall-through */
+	case e1000_82574:
+	case e1000_82583:
+		/* Stable 25MHz frequency */
+		incperiod = INCPERIOD_25MHz;
+		incvalue = INCVALUE_25MHz;
+		shift = INCVALUE_SHIFT_25MHz;
+		adapter->cc.shift = shift;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	*timinca = ((incperiod << E1000_TIMINCA_INCPERIOD_SHIFT) |
+		    ((incvalue << shift) & E1000_TIMINCA_INCVALUE_MASK));
+
+	return 0;
+}
+
+/**
+ * e1000e_config_hwtstamp - configure the hwtstamp registers and enable/disable
+ * @adapter: board private structure
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	struct hwtstamp_config *config = &adapter->hwtstamp_config;
+	u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
+	u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
+	u32 regval;
+	s32 ret_val;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return -EINVAL;
+
+	/* flags reserved for future extensions - must be zero */
+	if (config->flags)
+		return -EINVAL;
+
+	switch (config->tx_type) {
+	case HWTSTAMP_TX_OFF:
+		tsync_tx_ctl = 0;
+		break;
+	case HWTSTAMP_TX_ON:
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	switch (config->rx_filter) {
+	case HWTSTAMP_FILTER_NONE:
+		tsync_rx_ctl = 0;
+		break;
+	case HWTSTAMP_FILTER_ALL:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
+		config->rx_filter = HWTSTAMP_FILTER_ALL;
+		break;
+	default:
+		return -ERANGE;
+	}
+
+	/* enable/disable Tx h/w time stamping */
+	regval = er32(TSYNCTXCTL);
+	regval &= ~E1000_TSYNCTXCTL_ENABLED;
+	regval |= tsync_tx_ctl;
+	ew32(TSYNCTXCTL, regval);
+	if ((er32(TSYNCTXCTL) & E1000_TSYNCTXCTL_ENABLED) !=
+	    (regval & E1000_TSYNCTXCTL_ENABLED)) {
+		e_err("Timesync Tx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* enable/disable Rx h/w time stamping */
+	regval = er32(TSYNCRXCTL);
+	regval &= ~(E1000_TSYNCRXCTL_ENABLED | E1000_TSYNCRXCTL_TYPE_MASK);
+	regval |= tsync_rx_ctl;
+	ew32(TSYNCRXCTL, regval);
+	if ((er32(TSYNCRXCTL) & (E1000_TSYNCRXCTL_ENABLED |
+				 E1000_TSYNCRXCTL_TYPE_MASK)) !=
+	    (regval & (E1000_TSYNCRXCTL_ENABLED |
+		       E1000_TSYNCRXCTL_TYPE_MASK))) {
+		e_err("Timesync Rx Control register not set as expected\n");
+		return -EAGAIN;
+	}
+
+	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
+	regval = er32(RXSTMPH);
+	regval = er32(TXSTMPH);
+
+	/* Get and set the System Time Register SYSTIM base frequency */
+	ret_val = e1000e_get_base_timinca(adapter, &regval);
+	if (ret_val)
+		return ret_val;
+	ew32(TIMINCA, regval);
+
+	/* reset the ns time counter */
+	timecounter_init(&adapter->tc, &adapter->cc,
+			 ktime_to_ns(ktime_get_real()));
+
+	return 0;
+}
+
 /**
  * e1000_configure - configure the hardware for Rx and Tx
  * @adapter: private board structure
@@ -3529,6 +3784,9 @@ void e1000e_reset(struct e1000_adapter *adapter)
 
 	e1000e_reset_adaptive(hw);
 
+	/* initialize systim and reset the ns time counter */
+	e1000e_config_hwtstamp(adapter);
+
 	if (!netif_running(adapter->netdev) &&
 	    !test_bit(__E1000_TESTING, &adapter->state)) {
 		e1000_power_down_phy(adapter);
@@ -3664,6 +3922,24 @@ void e1000e_reinit_locked(struct e1000_adapter *adapter)
 	clear_bit(__E1000_RESETTING, &adapter->state);
 }
 
+/**
+ * e1000e_cyclecounter_read - read raw cycle counter (used by time counter)
+ * @cc: cyclecounter structure
+ **/
+static cycle_t e1000e_cyclecounter_read(const struct cyclecounter *cc)
+{
+	struct e1000_adapter *adapter = container_of(cc, struct e1000_adapter,
+						     cc);
+	struct e1000_hw *hw = &adapter->hw;
+	cycle_t systim;
+
+	/* latch SYSTIMH on read of SYSTIML */
+	systim = (cycle_t)er32(SYSTIML);
+	systim |= (cycle_t)er32(SYSTIMH) << 32;
+
+	return systim;
+}
+
 /**
  * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
  * @adapter: board private structure to initialize
@@ -3690,6 +3966,17 @@ static int e1000_sw_init(struct e1000_adapter *adapter)
 	if (e1000_alloc_queues(adapter))
 		return -ENOMEM;
 
+	/* Setup hardware time stamping cyclecounter */
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		adapter->cc.read = e1000e_cyclecounter_read;
+		adapter->cc.mask = CLOCKSOURCE_MASK(64);
+		adapter->cc.mult = 1;
+		/* cc.shift set in e1000e_get_base_tininca() */
+
+		spin_lock_init(&adapter->systim_lock);
+		INIT_WORK(&adapter->tx_hwtstamp_work, e1000e_tx_hwtstamp_work);
+	}
+
 	/* Explicitly disable IRQ since the NIC can be in any state. */
 	e1000_irq_disable(adapter);
 
@@ -4597,6 +4884,17 @@ link_up:
 	if (adapter->flags2 & FLAG2_CHECK_PHY_HANG)
 		e1000e_check_82574_phy_workaround(adapter);
 
+	/* Clear valid timestamp stuck in RXSTMPL/H due to a Rx error */
+	if (adapter->hwtstamp_config.rx_filter != HWTSTAMP_FILTER_NONE) {
+		if ((adapter->flags2 & FLAG2_CHECK_RX_HWTSTAMP) &&
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_VALID)) {
+			er32(RXSTMPH);
+			adapter->rx_hwtstamp_cleared++;
+		} else {
+			adapter->flags2 |= FLAG2_CHECK_RX_HWTSTAMP;
+		}
+	}
+
 	/* Reset the timer */
 	if (!test_bit(__E1000_DOWN, &adapter->state))
 		mod_timer(&adapter->watchdog_timer,
@@ -4608,6 +4906,7 @@ link_up:
 #define E1000_TX_FLAGS_TSO		0x00000004
 #define E1000_TX_FLAGS_IPV4		0x00000008
 #define E1000_TX_FLAGS_NO_FCS		0x00000010
+#define E1000_TX_FLAGS_HWTSTAMP		0x00000020
 #define E1000_TX_FLAGS_VLAN_MASK	0xffff0000
 #define E1000_TX_FLAGS_VLAN_SHIFT	16
 
@@ -4866,6 +5165,11 @@ static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
 	if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
 		txd_lower &= ~(E1000_TXD_CMD_IFCS);
 
+	if (unlikely(tx_flags & E1000_TX_FLAGS_HWTSTAMP)) {
+		txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
+		txd_upper |= E1000_TXD_EXTCMD_TSTAMP;
+	}
+
 	i = tx_ring->next_to_use;
 
 	do {
@@ -5089,7 +5393,15 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
 	count = e1000_tx_map(tx_ring, skb, first, adapter->tx_fifo_limit,
 			     nr_frags);
 	if (count) {
-		skb_tx_timestamp(skb);
+		if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
+			     !adapter->tx_hwtstamp_skb)) {
+			skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
+			tx_flags |= E1000_TX_FLAGS_HWTSTAMP;
+			adapter->tx_hwtstamp_skb = skb_get(skb);
+			schedule_work(&adapter->tx_hwtstamp_work);
+		} else {
+			skb_tx_timestamp(skb);
+		}
 
 		netdev_sent_queue(netdev, skb->len);
 		e1000_tx_queue(tx_ring, tx_flags, count);
@@ -5317,6 +5629,43 @@ static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
 	return 0;
 }
 
+/**
+ * e1000e_hwtstamp_ioctl - control hardware time stamping
+ * @netdev: network interface device structure
+ * @ifreq: interface request
+ *
+ * Outgoing time stamping can be enabled and disabled. Play nice and
+ * disable it when requested, although it shouldn't cause any overhead
+ * when no packet needs it. At most one packet in the queue may be
+ * marked for time stamping, otherwise it would be impossible to tell
+ * for sure to which packet the hardware time stamp belongs.
+ *
+ * Incoming time stamping has to be configured via the hardware filters.
+ * Not all combinations are supported, in particular event type has to be
+ * specified. Matching the kind of event packet is not supported, with the
+ * exception of "all V2 events regardless of level 2 or 4".
+ **/
+static int e1000e_hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr)
+{
+	struct e1000_adapter *adapter = netdev_priv(netdev);
+	struct hwtstamp_config config;
+	int ret_val;
+
+	if (copy_from_user(&config, ifr->ifr_data, sizeof(config)))
+		return -EFAULT;
+
+	adapter->hwtstamp_config = config;
+
+	ret_val = e1000e_config_hwtstamp(adapter);
+	if (ret_val)
+		return ret_val;
+
+	config = adapter->hwtstamp_config;
+
+	return copy_to_user(ifr->ifr_data, &config,
+			    sizeof(config)) ? -EFAULT : 0;
+}
+
 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 {
 	switch (cmd) {
@@ -5324,6 +5673,8 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
 	case SIOCGMIIREG:
 	case SIOCSMIIREG:
 		return e1000_mii_ioctl(netdev, ifr, cmd);
+	case SIOCSHWTSTAMP:
+		return e1000e_hwtstamp_ioctl(netdev, ifr);
 	default:
 		return -EOPNOTSUPP;
 	}
@@ -6380,6 +6731,14 @@ static void e1000_remove(struct pci_dev *pdev)
 	cancel_work_sync(&adapter->update_phy_task);
 	cancel_work_sync(&adapter->print_hang_task);
 
+	if (adapter->flags & FLAG_HAS_HW_TIMESTAMP) {
+		cancel_work_sync(&adapter->tx_hwtstamp_work);
+		if (adapter->tx_hwtstamp_skb) {
+			dev_kfree_skb_any(adapter->tx_hwtstamp_skb);
+			adapter->tx_hwtstamp_skb = NULL;
+		}
+	}
+
 	if (!(netdev->flags & IFF_UP))
 		e1000_power_down_phy(adapter);
 
-- 
cgit v1.2.3


From d89777bf0e42e7cb6ce8eae35190b9375c3b4211 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 19 Jan 2013 01:09:58 +0000
Subject: e1000e: add support for IEEE-1588 PTP

Add PTP IEEE-1588 support and make accesible via the PHC subsystem.

v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger

Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/Kconfig          |   1 +
 drivers/net/ethernet/intel/e1000e/Makefile  |   2 +-
 drivers/net/ethernet/intel/e1000e/defines.h |  11 ++
 drivers/net/ethernet/intel/e1000e/e1000.h   |   9 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c |  12 ++
 drivers/net/ethernet/intel/e1000e/hw.h      |   2 +
 drivers/net/ethernet/intel/e1000e/netdev.c  | 107 ++++++++++-
 drivers/net/ethernet/intel/e1000e/ptp.c     | 276 ++++++++++++++++++++++++++++
 8 files changed, 417 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/ptp.c

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/Kconfig b/drivers/net/ethernet/intel/Kconfig
index 21353f0fef63..3d5f6d463757 100644
--- a/drivers/net/ethernet/intel/Kconfig
+++ b/drivers/net/ethernet/intel/Kconfig
@@ -74,6 +74,7 @@ config E1000E
 	tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
 	depends on PCI && (!SPARC32 || BROKEN)
 	select CRC32
+	select PTP_1588_CLOCK
 	---help---
 	  This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
 	  ethernet family of adapters. For PCI or PCI-X e1000 adapters,
diff --git a/drivers/net/ethernet/intel/e1000e/Makefile b/drivers/net/ethernet/intel/e1000e/Makefile
index 591b71324505..1da0faac0411 100644
--- a/drivers/net/ethernet/intel/e1000e/Makefile
+++ b/drivers/net/ethernet/intel/e1000e/Makefile
@@ -34,5 +34,5 @@ obj-$(CONFIG_E1000E) += e1000e.o
 
 e1000e-objs := 82571.o ich8lan.o 80003es2lan.o \
 	       mac.o manage.o nvm.o phy.o \
-	       param.o ethtool.o netdev.o
+	       param.o ethtool.o netdev.o ptp.o
 
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 36f9fad19a76..5cb7441dca2a 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -544,9 +544,20 @@
 
 #define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
 #define E1000_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
+#define E1000_TSYNCRXCTL_TYPE_L2_V2	0x00
+#define E1000_TSYNCRXCTL_TYPE_L4_V1	0x02
+#define E1000_TSYNCRXCTL_TYPE_L2_L4_V2	0x04
+#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
+#define E1000_TSYNCRXCTL_TYPE_EVENT_V2	0x0A
 #define E1000_TSYNCRXCTL_ENABLED	0x00000010 /* enable Rx timestamping */
 #define E1000_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
 
+#define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE	0x00000000
+#define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE	0x00010000
+
+#define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE	0x00000000
+#define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE	0x01000000
+
 #define E1000_TIMINCA_INCPERIOD_SHIFT	24
 #define E1000_TIMINCA_INCVALUE_MASK	0x00FFFFFF
 
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index dea9e5552966..bd5876171376 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -43,7 +43,8 @@
 #include <linux/if_vlan.h>
 #include <linux/clocksource.h>
 #include <linux/net_tstamp.h>
-
+#include <linux/ptp_clock_kernel.h>
+#include <linux/ptp_classify.h>
 #include "hw.h"
 
 struct e1000_info;
@@ -413,6 +414,8 @@ struct e1000_adapter {
 	spinlock_t systim_lock;	/* protects SYSTIML/H regsters */
 	struct cyclecounter cc;
 	struct timecounter tc;
+	struct ptp_clock *ptp_clock;
+	struct ptp_clock_info ptp_clock_info;
 };
 
 struct e1000_info {
@@ -427,6 +430,8 @@ struct e1000_info {
 	const struct e1000_nvm_operations *nvm_ops;
 };
 
+s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca);
+
 /* The system time is maintained by a 64-bit counter comprised of the 32-bit
  * SYSTIMH and SYSTIML registers.  How the counter increments (and therefore
  * its resolution) is based on the contents of the TIMINCA register - it
@@ -704,6 +709,8 @@ extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
 extern bool e1000_check_phy_82574(struct e1000_hw *hw);
 extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
+extern void e1000e_ptp_init(struct e1000_adapter *adapter);
+extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
 static inline s32 e1000_phy_hw_reset(struct e1000_hw *hw)
 {
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index ceff1bf300b3..e3855bb10599 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -2209,8 +2209,20 @@ static int e1000e_get_ts_info(struct net_device *netdev,
 	info->tx_types = (1 << HWTSTAMP_TX_OFF) | (1 << HWTSTAMP_TX_ON);
 
 	info->rx_filters = ((1 << HWTSTAMP_FILTER_NONE) |
+			    (1 << HWTSTAMP_FILTER_PTP_V1_L4_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L4_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L2_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_EVENT) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_SYNC) |
+			    (1 << HWTSTAMP_FILTER_PTP_V2_DELAY_REQ) |
 			    (1 << HWTSTAMP_FILTER_ALL));
 
+	if (adapter->ptp_clock)
+		info->phc_index = ptp_clock_index(adapter->ptp_clock);
+
 	return 0;
 }
 
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 8e7e80345a60..84e6beb78718 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -251,6 +251,8 @@ enum e1e_registers {
 	E1000_TSYNCRXCTL = 0x0B620, /* Rx Time Sync Control register - RW */
 	E1000_RXSTMPL   = 0x0B624, /* Rx timestamp Low - RO */
 	E1000_RXSTMPH   = 0x0B628, /* Rx timestamp High - RO */
+	E1000_RXMTRL    = 0x0B634, /* Timesync Rx EtherType and Msg Type - RW */
+	E1000_RXUDP     = 0x0B638, /* Timesync Rx UDP Port - RW */
 };
 
 #define E1000_MAX_PHY_ADDR		4
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 8bb5d28eca14..34be756ee1e2 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3413,7 +3413,7 @@ static void e1000e_setup_rss_hash(struct e1000_adapter *adapter)
  * Get attributes for incrementing the System Time Register SYSTIML/H at
  * the default base frequency, and set the cyclecounter shift value.
  **/
-static s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
+s32 e1000e_get_base_timinca(struct e1000_adapter *adapter, u32 *timinca)
 {
 	struct e1000_hw *hw = &adapter->hw;
 	u32 incvalue, incperiod, shift;
@@ -3485,6 +3485,10 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 	struct hwtstamp_config *config = &adapter->hwtstamp_config;
 	u32 tsync_tx_ctl = E1000_TSYNCTXCTL_ENABLED;
 	u32 tsync_rx_ctl = E1000_TSYNCRXCTL_ENABLED;
+	u32 rxmtrl = 0;
+	u16 rxudp = 0;
+	bool is_l4 = false;
+	bool is_l2 = false;
 	u32 regval;
 	s32 ret_val;
 
@@ -3509,7 +3513,69 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 	case HWTSTAMP_FILTER_NONE:
 		tsync_rx_ctl = 0;
 		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
+		rxmtrl = E1000_RXMTRL_PTP_V1_SYNC_MESSAGE;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L4_V1;
+		rxmtrl = E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+		/* Also time stamps V2 L2 Path Delay Request/Response */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
+		is_l2 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+		/* Also time stamps V2 L2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
+		is_l2 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+		/* Hardware cannot filter just V2 L4 Sync messages;
+		 * fall-through to V2 (both L2 and L4) Sync.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_SYNC:
+		/* Also time stamps V2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_SYNC_MESSAGE;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+		/* Hardware cannot filter just V2 L4 Delay Request messages;
+		 * fall-through to V2 (both L2 and L4) Delay Request.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+		/* Also time stamps V2 Path Delay Request/Response. */
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_L2_L4_V2;
+		rxmtrl = E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
+	case HWTSTAMP_FILTER_PTP_V2_L2_EVENT:
+		/* Hardware cannot filter just V2 L4 or L2 Event messages;
+		 * fall-through to all V2 (both L2 and L4) Events.
+		 */
+	case HWTSTAMP_FILTER_PTP_V2_EVENT:
+		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_EVENT_V2;
+		config->rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
+		is_l2 = true;
+		is_l4 = true;
+		break;
+	case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
+		/* For V1, the hardware can only filter Sync messages or
+		 * Delay Request messages but not both so fall-through to
+		 * time stamp all packets.
+		 */
 	case HWTSTAMP_FILTER_ALL:
+		is_l2 = true;
+		is_l4 = true;
 		tsync_rx_ctl |= E1000_TSYNCRXCTL_TYPE_ALL;
 		config->rx_filter = HWTSTAMP_FILTER_ALL;
 		break;
@@ -3541,6 +3607,22 @@ static int e1000e_config_hwtstamp(struct e1000_adapter *adapter)
 		return -EAGAIN;
 	}
 
+	/* L2: define ethertype filter for time stamped packets */
+	if (is_l2)
+		rxmtrl |= ETH_P_1588;
+
+	/* define which PTP packets get time stamped */
+	ew32(RXMTRL, rxmtrl);
+
+	/* Filter by destination port */
+	if (is_l4) {
+		rxudp = PTP_EV_PORT;
+		cpu_to_be16s(&rxudp);
+	}
+	ew32(RXUDP, rxudp);
+
+	e1e_flush();
+
 	/* Clear TSYNCRXCTL_VALID & TSYNCTXCTL_VALID bit */
 	regval = er32(RXSTMPH);
 	regval = er32(TXSTMPH);
@@ -5665,6 +5747,24 @@ static int e1000e_hwtstamp_ioctl(struct net_device *netdev, struct ifreq *ifr)
 
 	config = adapter->hwtstamp_config;
 
+	switch (config.rx_filter) {
+	case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_SYNC:
+	case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
+	case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ:
+	case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
+		/* With V2 type filters which specify a Sync or Delay Request,
+		 * Path Delay Request/Response messages are also time stamped
+		 * by hardware so notify the caller the requested packets plus
+		 * some others are time stamped.
+		 */
+		config.rx_filter = HWTSTAMP_FILTER_SOME;
+		break;
+	default:
+		break;
+	}
+
 	return copy_to_user(ifr->ifr_data, &config,
 			    sizeof(config)) ? -EFAULT : 0;
 }
@@ -6672,6 +6772,9 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	/* carrier off reporting is important to ethtool even BEFORE open */
 	netif_carrier_off(netdev);
 
+	/* init PTP hardware clock */
+	e1000e_ptp_init(adapter);
+
 	e1000_print_device_info(adapter);
 
 	if (pci_dev_run_wake(pdev))
@@ -6720,6 +6823,8 @@ static void e1000_remove(struct pci_dev *pdev)
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	bool down = test_bit(__E1000_DOWN, &adapter->state);
 
+	e1000e_ptp_remove(adapter);
+
 	/* The timers may be rescheduled, so explicitly disable them
 	 * from being rescheduled.
 	 */
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
new file mode 100644
index 000000000000..32da00c0cbc9
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -0,0 +1,276 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2012 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+/* PTP 1588 Hardware Clock (PHC)
+ * Derived from PTP Hardware Clock driver for Intel 82576 and 82580 (igb)
+ * Copyright (C) 2011 Richard Cochran <richardcochran@gmail.com>
+ */
+
+#include "e1000.h"
+
+/**
+ * e1000e_phc_adjfreq - adjust the frequency of the hardware clock
+ * @ptp: ptp clock structure
+ * @delta: Desired frequency change in parts per billion
+ *
+ * Adjust the frequency of the PHC cycle counter by the indicated delta from
+ * the base frequency.
+ **/
+static int e1000e_phc_adjfreq(struct ptp_clock_info *ptp, s32 delta)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	struct e1000_hw *hw = &adapter->hw;
+	bool neg_adj = false;
+	u64 adjustment;
+	u32 timinca, incvalue;
+	s32 ret_val;
+
+	if ((delta > ptp->max_adj) || (delta <= -1000000000))
+		return -EINVAL;
+
+	if (delta < 0) {
+		neg_adj = true;
+		delta = -delta;
+	}
+
+	/* Get the System Time Register SYSTIM base frequency */
+	ret_val = e1000e_get_base_timinca(adapter, &timinca);
+	if (ret_val)
+		return ret_val;
+
+	incvalue = timinca & E1000_TIMINCA_INCVALUE_MASK;
+
+	adjustment = incvalue;
+	adjustment *= delta;
+	adjustment = div_u64(adjustment, 1000000000);
+
+	incvalue = neg_adj ? (incvalue - adjustment) : (incvalue + adjustment);
+
+	timinca &= ~E1000_TIMINCA_INCVALUE_MASK;
+	timinca |= incvalue;
+
+	ew32(TIMINCA, timinca);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_adjtime - Shift the time of the hardware clock
+ * @ptp: ptp clock structure
+ * @delta: Desired change in nanoseconds
+ *
+ * Adjust the timer by resetting the timecounter structure.
+ **/
+static int e1000e_phc_adjtime(struct ptp_clock_info *ptp, s64 delta)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	s64 now;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	now = timecounter_read(&adapter->tc);
+	now += delta;
+	timecounter_init(&adapter->tc, &adapter->cc, now);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_gettime - Reads the current time from the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec structure to hold the current time value
+ *
+ * Read the timecounter and return the correct value in ns after converting
+ * it into a struct timespec.
+ **/
+static int e1000e_phc_gettime(struct ptp_clock_info *ptp, struct timespec *ts)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	u32 remainder;
+	u64 ns;
+
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	ns = timecounter_read(&adapter->tc);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	ts->tv_sec = div_u64_rem(ns, NSEC_PER_SEC, &remainder);
+	ts->tv_nsec = remainder;
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_settime - Set the current time on the hardware clock
+ * @ptp: ptp clock structure
+ * @ts: timespec containing the new time for the cycle counter
+ *
+ * Reset the timecounter to use a new base value instead of the kernel
+ * wall timer value.
+ **/
+static int e1000e_phc_settime(struct ptp_clock_info *ptp,
+			      const struct timespec *ts)
+{
+	struct e1000_adapter *adapter = container_of(ptp, struct e1000_adapter,
+						     ptp_clock_info);
+	unsigned long flags;
+	u64 ns;
+
+	ns = ts->tv_sec * NSEC_PER_SEC;
+	ns += ts->tv_nsec;
+
+	/* reset the timecounter */
+	spin_lock_irqsave(&adapter->systim_lock, flags);
+	timecounter_init(&adapter->tc, &adapter->cc, ns);
+	spin_unlock_irqrestore(&adapter->systim_lock, flags);
+
+	return 0;
+}
+
+/**
+ * e1000e_phc_enable - enable or disable an ancillary feature
+ * @ptp: ptp clock structure
+ * @request: Desired resource to enable or disable
+ * @on: Caller passes one to enable or zero to disable
+ *
+ * Enable (or disable) ancillary features of the PHC subsystem.
+ * Currently, no ancillary features are supported.
+ **/
+static int e1000e_phc_enable(struct ptp_clock_info *ptp,
+			     struct ptp_clock_request *request, int on)
+{
+	return -EOPNOTSUPP;
+}
+
+static void e1000e_systim_overflow_work(struct work_struct *work)
+{
+	struct e1000_adapter *adapter = container_of(work, struct e1000_adapter,
+						     systim_overflow_work.work);
+	struct e1000_hw *hw = &adapter->hw;
+	struct timespec ts;
+
+	adapter->ptp_clock_info.gettime(&adapter->ptp_clock_info, &ts);
+
+	e_dbg("SYSTIM overflow check at %ld.%09lu\n", ts.tv_sec, ts.tv_nsec);
+
+	schedule_delayed_work(&adapter->systim_overflow_work,
+			      E1000_SYSTIM_OVERFLOW_PERIOD);
+}
+
+static const struct ptp_clock_info e1000e_ptp_clock_info = {
+	.owner		= THIS_MODULE,
+	.n_alarm	= 0,
+	.n_ext_ts	= 0,
+	.n_per_out	= 0,
+	.pps		= 0,
+	.adjfreq	= e1000e_phc_adjfreq,
+	.adjtime	= e1000e_phc_adjtime,
+	.gettime	= e1000e_phc_gettime,
+	.settime	= e1000e_phc_settime,
+	.enable		= e1000e_phc_enable,
+};
+
+/**
+ * e1000e_ptp_init - initialize PTP for devices which support it
+ * @adapter: board private structure
+ *
+ * This function performs the required steps for enabling PTP support.
+ * If PTP support has already been loaded it simply calls the cyclecounter
+ * init routine and exits.
+ **/
+void e1000e_ptp_init(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+
+	adapter->ptp_clock = NULL;
+
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return;
+
+	adapter->ptp_clock_info = e1000e_ptp_clock_info;
+
+	snprintf(adapter->ptp_clock_info.name,
+		 sizeof(adapter->ptp_clock_info.name), "%pm",
+		 adapter->netdev->perm_addr);
+
+	switch (hw->mac.type) {
+	case e1000_pch2lan:
+	case e1000_pch_lpt:
+		if ((hw->mac.type != e1000_pch_lpt) ||
+		    (er32(TSYNCRXCTL) & E1000_TSYNCRXCTL_SYSCFI)) {
+			adapter->ptp_clock_info.max_adj = 24000000 - 1;
+			break;
+		}
+		/* fall-through */
+	case e1000_82574:
+	case e1000_82583:
+		adapter->ptp_clock_info.max_adj = 600000000 - 1;
+		break;
+	default:
+		break;
+	}
+
+	INIT_DELAYED_WORK(&adapter->systim_overflow_work,
+			  e1000e_systim_overflow_work);
+
+	schedule_delayed_work(&adapter->systim_overflow_work,
+			      E1000_SYSTIM_OVERFLOW_PERIOD);
+
+	adapter->ptp_clock = ptp_clock_register(&adapter->ptp_clock_info,
+						&adapter->pdev->dev);
+	if (IS_ERR(adapter->ptp_clock)) {
+		adapter->ptp_clock = NULL;
+		e_err("ptp_clock_register failed\n");
+	} else {
+		e_info("registered PHC clock\n");
+	}
+}
+
+/**
+ * e1000e_ptp_remove - disable PTP device and stop the overflow check
+ * @adapter: board private structure
+ *
+ * Stop the PTP support, and cancel the delayed work.
+ **/
+void e1000e_ptp_remove(struct e1000_adapter *adapter)
+{
+	if (!(adapter->flags & FLAG_HAS_HW_TIMESTAMP))
+		return;
+
+	cancel_delayed_work_sync(&adapter->systim_overflow_work);
+
+	if (adapter->ptp_clock) {
+		ptp_clock_unregister(adapter->ptp_clock);
+		adapter->ptp_clock = NULL;
+		e_info("removed PHC\n");
+	}
+}
-- 
cgit v1.2.3


From 94fb848bf43fae3410639fb2110a783200e9e1da Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 23 Jan 2013 09:00:03 +0000
Subject: e1000e: enable ECC on I217/I218 to catch packet buffer memory errors

In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions.  Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors.  Correctable errors will be handled
by the hardware.  Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded.  If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error.  The driver will then reset the hardware in order to
clear the error and restart.

Both types of errors will be accounted for in statistics counters.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  9 ++++++
 drivers/net/ethernet/intel/e1000e/e1000.h   |  2 ++
 drivers/net/ethernet/intel/e1000e/ethtool.c |  2 ++
 drivers/net/ethernet/intel/e1000e/hw.h      |  1 +
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 11 +++++++
 drivers/net/ethernet/intel/e1000e/netdev.c  | 46 +++++++++++++++++++++++++++++
 6 files changed, 71 insertions(+)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 5cb7441dca2a..f0452311c95a 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -233,6 +233,7 @@
 #define E1000_CTRL_FRCDPX   0x00001000  /* Force Duplex */
 #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */
 #define E1000_CTRL_LANPHYPC_VALUE    0x00020000 /* SW value of LANPHYPC */
+#define E1000_CTRL_MEHE     0x00080000  /* Memory Error Handling Enable */
 #define E1000_CTRL_SWDPIN0  0x00040000  /* SWDPIN 0 value */
 #define E1000_CTRL_SWDPIN1  0x00080000  /* SWDPIN 1 value */
 #define E1000_CTRL_SWDPIO0  0x00400000  /* SWDPIN 0 Input or output */
@@ -394,6 +395,12 @@
 
 #define E1000_PBS_16K E1000_PBA_16K
 
+/* Uncorrectable/correctable ECC Error counts and enable bits */
+#define E1000_PBECCSTS_CORR_ERR_CNT_MASK	0x000000FF
+#define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK	0x0000FF00
+#define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT	8
+#define E1000_PBECCSTS_ECC_ENABLE		0x00010000
+
 #define IFS_MAX       80
 #define IFS_MIN       40
 #define IFS_RATIO     4
@@ -413,6 +420,7 @@
 #define E1000_ICR_RXSEQ         0x00000008 /* Rx sequence error */
 #define E1000_ICR_RXDMT0        0x00000010 /* Rx desc min. threshold (0) */
 #define E1000_ICR_RXT0          0x00000080 /* Rx timer intr (ring 0) */
+#define E1000_ICR_ECCER         0x00400000 /* Uncorrectable ECC Error */
 #define E1000_ICR_INT_ASSERTED  0x80000000 /* If this bit asserted, the driver should claim the interrupt */
 #define E1000_ICR_RXQ0          0x00100000 /* Rx Queue 0 Interrupt */
 #define E1000_ICR_RXQ1          0x00200000 /* Rx Queue 1 Interrupt */
@@ -448,6 +456,7 @@
 #define E1000_IMS_RXSEQ     E1000_ICR_RXSEQ     /* Rx sequence error */
 #define E1000_IMS_RXDMT0    E1000_ICR_RXDMT0    /* Rx desc min. threshold */
 #define E1000_IMS_RXT0      E1000_ICR_RXT0      /* Rx timer intr */
+#define E1000_IMS_ECCER     E1000_ICR_ECCER     /* Uncorrectable ECC Error */
 #define E1000_IMS_RXQ0      E1000_ICR_RXQ0      /* Rx Queue 0 Interrupt */
 #define E1000_IMS_RXQ1      E1000_ICR_RXQ1      /* Rx Queue 1 Interrupt */
 #define E1000_IMS_TXQ0      E1000_ICR_TXQ0      /* Tx Queue 0 Interrupt */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index bd5876171376..c96e6fcfdcbc 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -312,6 +312,8 @@ struct e1000_adapter {
 
 	struct napi_struct napi;
 
+	unsigned int uncorr_errors;	/* uncorrectable ECC errors */
+	unsigned int corr_errors;	/* correctable ECC errors */
 	unsigned int restart_queue;
 	u32 txd_cmd;
 
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index e3855bb10599..124821b49df6 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -109,6 +109,8 @@ static const struct e1000_stats e1000_gstrings_stats[] = {
 	E1000_STAT("rx_dma_failed", rx_dma_failed),
 	E1000_STAT("tx_dma_failed", tx_dma_failed),
 	E1000_STAT("rx_hwtstamp_cleared", rx_hwtstamp_cleared),
+	E1000_STAT("uncorr_ecc_errors", uncorr_errors),
+	E1000_STAT("corr_ecc_errors", corr_errors),
 };
 
 #define E1000_GLOBAL_STATS_LEN	ARRAY_SIZE(e1000_gstrings_stats)
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 84e6beb78718..4bd49be5915a 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -79,6 +79,7 @@ enum e1e_registers {
 #define E1000_POEMB	E1000_PHY_CTRL	/* PHY OEM Bits */
 	E1000_PBA      = 0x01000, /* Packet Buffer Allocation - RW */
 	E1000_PBS      = 0x01008, /* Packet Buffer Size */
+	E1000_PBECCSTS = 0x0100C, /* Packet Buffer ECC Status - RW */
 	E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */
 	E1000_EEWR     = 0x0102C, /* EEPROM Write Register - RW */
 	E1000_FLOP     = 0x0103C, /* FLASH Opcode Register */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 50935ef48171..56cbfa7981eb 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -3704,6 +3704,17 @@ static void e1000_initialize_hw_bits_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_ich8lan)
 		reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
 	ew32(RFCTL, reg);
+
+	/* Enable ECC on Lynxpoint */
+	if (hw->mac.type == e1000_pch_lpt) {
+		reg = er32(PBECCSTS);
+		reg |= E1000_PBECCSTS_ECC_ENABLE;
+		ew32(PBECCSTS, reg);
+
+		reg = er32(CTRL);
+		reg |= E1000_CTRL_MEHE;
+		ew32(CTRL, reg);
+	}
 }
 
 /**
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 34be756ee1e2..4c7e9fe23458 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1780,6 +1780,23 @@ static irqreturn_t e1000_intr_msi(int irq, void *data)
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	/* Reset on uncorrectable ECC error */
+	if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+		u32 pbeccsts = er32(PBECCSTS);
+
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+
+		/* Do the reset outside of interrupt context */
+		schedule_work(&adapter->reset_task);
+
+		/* return immediately since reset is imminent */
+		return IRQ_HANDLED;
+	}
+
 	if (napi_schedule_prep(&adapter->napi)) {
 		adapter->total_tx_bytes = 0;
 		adapter->total_tx_packets = 0;
@@ -1843,6 +1860,23 @@ static irqreturn_t e1000_intr(int irq, void *data)
 			mod_timer(&adapter->watchdog_timer, jiffies + 1);
 	}
 
+	/* Reset on uncorrectable ECC error */
+	if ((icr & E1000_ICR_ECCER) && (hw->mac.type == e1000_pch_lpt)) {
+		u32 pbeccsts = er32(PBECCSTS);
+
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+
+		/* Do the reset outside of interrupt context */
+		schedule_work(&adapter->reset_task);
+
+		/* return immediately since reset is imminent */
+		return IRQ_HANDLED;
+	}
+
 	if (napi_schedule_prep(&adapter->napi)) {
 		adapter->total_tx_bytes = 0;
 		adapter->total_tx_packets = 0;
@@ -2206,6 +2240,8 @@ static void e1000_irq_enable(struct e1000_adapter *adapter)
 	if (adapter->msix_entries) {
 		ew32(EIAC_82574, adapter->eiac_mask & E1000_EIAC_MASK_82574);
 		ew32(IMS, adapter->eiac_mask | E1000_IMS_OTHER | E1000_IMS_LSC);
+	} else if (hw->mac.type == e1000_pch_lpt) {
+		ew32(IMS, IMS_ENABLE_MASK | E1000_IMS_ECCER);
 	} else {
 		ew32(IMS, IMS_ENABLE_MASK);
 	}
@@ -4619,6 +4655,16 @@ static void e1000e_update_stats(struct e1000_adapter *adapter)
 	adapter->stats.mgptc += er32(MGTPTC);
 	adapter->stats.mgprc += er32(MGTPRC);
 	adapter->stats.mgpdc += er32(MGTPDC);
+
+	/* Correctable ECC Errors */
+	if (hw->mac.type == e1000_pch_lpt) {
+		u32 pbeccsts = er32(PBECCSTS);
+		adapter->corr_errors +=
+		    pbeccsts & E1000_PBECCSTS_CORR_ERR_CNT_MASK;
+		adapter->uncorr_errors +=
+		    (pbeccsts & E1000_PBECCSTS_UNCORR_ERR_CNT_MASK) >>
+		    E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT;
+	}
 }
 
 /**
-- 
cgit v1.2.3


From bf67044bf86d9b5613cdba9d7d04deb4ea08892e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 1 Jan 2013 16:00:01 +0000
Subject: e1000e: update copyright date

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 2 +-
 drivers/net/ethernet/intel/e1000e/82571.c       | 2 +-
 drivers/net/ethernet/intel/e1000e/Makefile      | 2 +-
 drivers/net/ethernet/intel/e1000e/defines.h     | 2 +-
 drivers/net/ethernet/intel/e1000e/e1000.h       | 2 +-
 drivers/net/ethernet/intel/e1000e/ethtool.c     | 2 +-
 drivers/net/ethernet/intel/e1000e/hw.h          | 2 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c     | 2 +-
 drivers/net/ethernet/intel/e1000e/mac.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/manage.c      | 2 +-
 drivers/net/ethernet/intel/e1000e/netdev.c      | 4 ++--
 drivers/net/ethernet/intel/e1000e/nvm.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/param.c       | 2 +-
 drivers/net/ethernet/intel/e1000e/phy.c         | 2 +-
 drivers/net/ethernet/intel/e1000e/ptp.c         | 2 +-
 15 files changed, 16 insertions(+), 16 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index e73c2c355993..97ff50e5eb5a 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 587890d2d55e..e9d9bef12599 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/Makefile b/drivers/net/ethernet/intel/e1000e/Makefile
index 1da0faac0411..c2dcfcc10857 100644
--- a/drivers/net/ethernet/intel/e1000e/Makefile
+++ b/drivers/net/ethernet/intel/e1000e/Makefile
@@ -1,7 +1,7 @@
 ################################################################################
 #
 # Intel PRO/1000 Linux driver
-# Copyright(c) 1999 - 2012 Intel Corporation.
+# Copyright(c) 1999 - 2013 Intel Corporation.
 #
 # This program is free software; you can redistribute it and/or modify it
 # under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index f0452311c95a..3b997194ac3b 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index b8020b8b15c4..c7bc610a0b55 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index 124821b49df6..4262b4d00609 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 4bd49be5915a..0a08b1438a18 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 9a93223bd09a..c25678dc2ddd 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 0fa4c0656e09..d21f749a6492 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/manage.c b/drivers/net/ethernet/intel/e1000e/manage.c
index 6dc47beb3adc..4dae0dbda837 100644
--- a/drivers/net/ethernet/intel/e1000e/manage.c
+++ b/drivers/net/ethernet/intel/e1000e/manage.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 4c7e9fe23458..12784e804f42 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
@@ -7045,7 +7045,7 @@ static int __init e1000_init_module(void)
 	int ret;
 	pr_info("Intel(R) PRO/1000 Network Driver - %s\n",
 		e1000e_driver_version);
-	pr_info("Copyright(c) 1999 - 2012 Intel Corporation.\n");
+	pr_info("Copyright(c) 1999 - 2013 Intel Corporation.\n");
 	ret = pci_register_driver(&e1000_driver);
 
 	return ret;
diff --git a/drivers/net/ethernet/intel/e1000e/nvm.c b/drivers/net/ethernet/intel/e1000e/nvm.c
index 1e7882c7d6d4..84fecc268162 100644
--- a/drivers/net/ethernet/intel/e1000e/nvm.c
+++ b/drivers/net/ethernet/intel/e1000e/nvm.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index b29a8a5116a8..19c40d6f53cc 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 28b38ff37e84..70f759399355 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
diff --git a/drivers/net/ethernet/intel/e1000e/ptp.c b/drivers/net/ethernet/intel/e1000e/ptp.c
index 32da00c0cbc9..6b8df6587858 100644
--- a/drivers/net/ethernet/intel/e1000e/ptp.c
+++ b/drivers/net/ethernet/intel/e1000e/ptp.c
@@ -1,7 +1,7 @@
 /*******************************************************************************
 
   Intel PRO/1000 Linux driver
-  Copyright(c) 1999 - 2012 Intel Corporation.
+  Copyright(c) 1999 - 2013 Intel Corporation.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms and conditions of the GNU General Public License,
-- 
cgit v1.2.3


From 3e35d9918cbbc224f88da4dd19cd90b2cd4f765e Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:25:22 +0000
Subject: e1000e: adjust PM QoS request

It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.  For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this.  To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  2 ++
 drivers/net/ethernet/intel/e1000e/netdev.c  | 32 +++++++++++++++--------------
 2 files changed, 19 insertions(+), 15 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 3b997194ac3b..c4587671dc73 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -393,6 +393,8 @@
 #define E1000_PBA_8K  0x0008    /* 8KB */
 #define E1000_PBA_16K 0x0010    /* 16KB */
 
+#define E1000_PBA_RXA_MASK	0xFFFF
+
 #define E1000_PBS_16K E1000_PBA_16K
 
 /* Uncorrectable/correctable ECC Error counts and enable bits */
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e386e95102f4..46a38a4d8da5 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -3242,18 +3242,23 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
 		rxcsum &= ~E1000_RXCSUM_TUOFL;
 	ew32(RXCSUM, rxcsum);
 
-	if (adapter->hw.mac.type == e1000_pch2lan) {
-		/* With jumbo frames, excessive C-state transition
-		 * latencies result in dropped transactions.
-		 */
-		if (adapter->netdev->mtu > ETH_DATA_LEN) {
+	/* With jumbo frames, excessive C-state transition latencies result
+	 * in dropped transactions.
+	 */
+	if (adapter->netdev->mtu > ETH_DATA_LEN) {
+		u32 lat =
+		    ((er32(PBA) & E1000_PBA_RXA_MASK) * 1024 -
+		     adapter->max_frame_size) * 8 / 1000;
+
+		if (adapter->flags & FLAG_IS_ICH) {
 			u32 rxdctl = er32(RXDCTL(0));
 			ew32(RXDCTL(0), rxdctl | 0x3);
-			pm_qos_update_request(&adapter->netdev->pm_qos_req, 55);
-		} else {
-			pm_qos_update_request(&adapter->netdev->pm_qos_req,
-					      PM_QOS_DEFAULT_VALUE);
 		}
+
+		pm_qos_update_request(&adapter->netdev->pm_qos_req, lat);
+	} else {
+		pm_qos_update_request(&adapter->netdev->pm_qos_req,
+				      PM_QOS_DEFAULT_VALUE);
 	}
 
 	/* Enable Receives */
@@ -4281,10 +4286,8 @@ static int e1000_open(struct net_device *netdev)
 		e1000_update_mng_vlan(adapter);
 
 	/* DMA latency requirement to workaround jumbo issue */
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_add_request(&adapter->netdev->pm_qos_req,
-				   PM_QOS_CPU_DMA_LATENCY,
-				   PM_QOS_DEFAULT_VALUE);
+	pm_qos_add_request(&adapter->netdev->pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
+			   PM_QOS_DEFAULT_VALUE);
 
 	/* before we allocate an interrupt, we must be ready to handle it.
 	 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
@@ -4392,8 +4395,7 @@ static int e1000_close(struct net_device *netdev)
 	    !test_bit(__E1000_TESTING, &adapter->state))
 		e1000e_release_hw_control(adapter);
 
-	if (adapter->hw.mac.type == e1000_pch2lan)
-		pm_qos_remove_request(&adapter->netdev->pm_qos_req);
+	pm_qos_remove_request(&adapter->netdev->pm_qos_req);
 
 	pm_runtime_put_sync(&pdev->dev);
 
-- 
cgit v1.2.3


From 39149d4da6d50de92f9e7f70c743a8b8c20eeac1 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:26:53 +0000
Subject: e1000e: cleanup: remove comments which are no longer applicable

Code was removed but the applicable comments were not.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h | 7 -------
 1 file changed, 7 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index c4587671dc73..d29b2fd4c09c 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -261,8 +261,6 @@
 #define E1000_STATUS_PHYRA      0x00000400      /* PHY Reset Asserted */
 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
 
-/* Constants used to interpret the masked PCI-X bus speed. */
-
 #define HALF_DUPLEX 1
 #define FULL_DUPLEX 2
 
@@ -330,8 +328,6 @@
 #define E1000_TCTL_RTLC   0x01000000    /* Re-transmit on late collision */
 #define E1000_TCTL_MULR   0x10000000    /* Multiple request support */
 
-/* Transmit Arbitration Count */
-
 /* SerDes Control */
 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
 
@@ -800,9 +796,6 @@
 #define M88E1000_PSCR_AUTO_X_1000T     0x0040
 /* Auto crossover enabled all speeds */
 #define M88E1000_PSCR_AUTO_X_MODE      0x0060
-/* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold)
- * 0=Normal 10BASE-T Rx Threshold
- */
 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
 
 /* M88E1000 PHY Specific Status Register */
-- 
cgit v1.2.3


From 0cdc63449df6ee5e7840b3e58554d7a41068b542 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:27:23 +0000
Subject: e1000e: cleanup defines.h

Remove redundant defines which are defined elsewhere.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h | 21 ---------------------
 1 file changed, 21 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index d29b2fd4c09c..acfe1fadd8de 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -29,25 +29,6 @@
 #ifndef _E1000_DEFINES_H_
 #define _E1000_DEFINES_H_
 
-#define E1000_TXD_POPTS_IXSM 0x01       /* Insert IP checksum */
-#define E1000_TXD_POPTS_TXSM 0x02       /* Insert TCP/UDP checksum */
-#define E1000_TXD_CMD_EOP    0x01000000 /* End of Packet */
-#define E1000_TXD_CMD_IFCS   0x02000000 /* Insert FCS (Ethernet CRC) */
-#define E1000_TXD_CMD_IC     0x04000000 /* Insert Checksum */
-#define E1000_TXD_CMD_RS     0x08000000 /* Report Status */
-#define E1000_TXD_CMD_RPS    0x10000000 /* Report Packet Sent */
-#define E1000_TXD_CMD_DEXT   0x20000000 /* Descriptor extension (0 = legacy) */
-#define E1000_TXD_CMD_VLE    0x40000000 /* Add VLAN tag */
-#define E1000_TXD_CMD_IDE    0x80000000 /* Enable Tidv register */
-#define E1000_TXD_STAT_DD    0x00000001 /* Descriptor Done */
-#define E1000_TXD_STAT_EC    0x00000002 /* Excess Collisions */
-#define E1000_TXD_STAT_LC    0x00000004 /* Late Collisions */
-#define E1000_TXD_STAT_TU    0x00000008 /* Transmit underrun */
-#define E1000_TXD_CMD_TCP    0x01000000 /* TCP packet */
-#define E1000_TXD_CMD_IP     0x02000000 /* IP packet */
-#define E1000_TXD_CMD_TSE    0x04000000 /* TCP Seg enable */
-#define E1000_TXD_STAT_TC    0x00000004 /* Tx Underrun */
-
 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
 #define REQ_TX_DESCRIPTOR_MULTIPLE  8
 #define REQ_RX_DESCRIPTOR_MULTIPLE  8
@@ -86,7 +67,6 @@
 #define E1000_CTRL_EXT_EIAME          0x01000000
 #define E1000_CTRL_EXT_DRV_LOAD       0x10000000 /* Driver loaded bit for FW */
 #define E1000_CTRL_EXT_IAME           0x08000000 /* Interrupt acknowledge Auto-mask */
-#define E1000_CTRL_EXT_INT_TIMER_CLR  0x20000000 /* Clear Interrupt timers after IMS clear */
 #define E1000_CTRL_EXT_PBA_CLR        0x80000000 /* PBA Clear */
 #define E1000_CTRL_EXT_LSECCK         0x00001000
 #define E1000_CTRL_EXT_PHYPDEN        0x00100000
@@ -546,7 +526,6 @@
 #define E1000_RXCW_SYNCH      0x40000000        /* Receive config synch */
 
 #define E1000_TSYNCTXCTL_VALID		0x00000001 /* Tx timestamp valid */
-#define E1000_TSYNCRXCTL_TYPE_ALL	0x08
 #define E1000_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
 
 #define E1000_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
-- 
cgit v1.2.3


From 55c5f55e524cec35b5931df16936118dc6c0837b Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Sat, 12 Jan 2013 07:28:24 +0000
Subject: e1000e: cleanup some whitespace and indentation issues

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c | 22 ++++++------
 drivers/net/ethernet/intel/e1000e/82571.c       | 13 +++----
 drivers/net/ethernet/intel/e1000e/defines.h     | 47 +++++++++++++------------
 drivers/net/ethernet/intel/e1000e/ich8lan.c     |  4 +--
 drivers/net/ethernet/intel/e1000e/mac.c         |  4 +--
 drivers/net/ethernet/intel/e1000e/netdev.c      |  4 +--
 drivers/net/ethernet/intel/e1000e/param.c       |  3 +-
 7 files changed, 49 insertions(+), 48 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 3f27546baaa7..765211a289d8 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -1438,18 +1438,18 @@ static const struct e1000_phy_operations es2_phy_ops = {
 	.acquire		= e1000_acquire_phy_80003es2lan,
 	.check_polarity		= e1000_check_polarity_m88,
 	.check_reset_block	= e1000e_check_reset_block_generic,
-	.commit		 	= e1000e_phy_sw_reset,
-	.force_speed_duplex 	= e1000_phy_force_speed_duplex_80003es2lan,
-	.get_cfg_done       	= e1000_get_cfg_done_80003es2lan,
-	.get_cable_length   	= e1000_get_cable_length_80003es2lan,
-	.get_info       	= e1000e_get_phy_info_m88,
-	.read_reg       	= e1000_read_phy_reg_gg82563_80003es2lan,
+	.commit			= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000_phy_force_speed_duplex_80003es2lan,
+	.get_cfg_done		= e1000_get_cfg_done_80003es2lan,
+	.get_cable_length	= e1000_get_cable_length_80003es2lan,
+	.get_info		= e1000e_get_phy_info_m88,
+	.read_reg		= e1000_read_phy_reg_gg82563_80003es2lan,
 	.release		= e1000_release_phy_80003es2lan,
-	.reset		  	= e1000e_phy_hw_reset_generic,
-	.set_d0_lplu_state  	= NULL,
-	.set_d3_lplu_state  	= e1000e_set_d3_lplu_state,
-	.write_reg      	= e1000_write_phy_reg_gg82563_80003es2lan,
-	.cfg_on_link_up      	= e1000_cfg_on_link_up_80003es2lan,
+	.reset			= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= NULL,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_reg		= e1000_write_phy_reg_gg82563_80003es2lan,
+	.cfg_on_link_up		= e1000_cfg_on_link_up_80003es2lan,
 };
 
 static const struct e1000_nvm_operations es2_nvm_ops = {
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index 076938c87a26..db364b69f87e 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -1327,9 +1327,10 @@ static void e1000_clear_vfta_82571(struct e1000_hw *hw)
 			 */
 			vfta_offset = (hw->mng_cookie.vlan_id >>
 				       E1000_VFTA_ENTRY_SHIFT) &
-				      E1000_VFTA_ENTRY_MASK;
-			vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
-					       E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
+			    E1000_VFTA_ENTRY_MASK;
+			vfta_bit_in_reg =
+			    1 << (hw->mng_cookie.vlan_id &
+				  E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
 		}
 		break;
 	default:
@@ -1931,7 +1932,7 @@ static const struct e1000_phy_operations e82_phy_ops_igp = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_igp,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_phy_operations e82_phy_ops_m88 = {
@@ -1949,7 +1950,7 @@ static const struct e1000_phy_operations e82_phy_ops_m88 = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_m88,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_phy_operations e82_phy_ops_bm = {
@@ -1967,7 +1968,7 @@ static const struct e1000_phy_operations e82_phy_ops_bm = {
 	.set_d0_lplu_state	= e1000_set_d0_lplu_state_82571,
 	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
 	.write_reg		= e1000e_write_phy_reg_bm2,
-	.cfg_on_link_up      	= NULL,
+	.cfg_on_link_up		= NULL,
 };
 
 static const struct e1000_nvm_operations e82571_nvm_ops = {
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index acfe1fadd8de..1257f917af34 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -96,19 +96,19 @@
 
 /* mask to determine if packets should be dropped due to frame errors */
 #define E1000_RXD_ERR_FRAME_ERR_MASK ( \
-    E1000_RXD_ERR_CE  |                \
-    E1000_RXD_ERR_SE  |                \
-    E1000_RXD_ERR_SEQ |                \
-    E1000_RXD_ERR_CXE |                \
-    E1000_RXD_ERR_RXE)
+	E1000_RXD_ERR_CE  |		\
+	E1000_RXD_ERR_SE  |		\
+	E1000_RXD_ERR_SEQ |		\
+	E1000_RXD_ERR_CXE |		\
+	E1000_RXD_ERR_RXE)
 
 /* Same mask, but for extended and packet split descriptors */
 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
-    E1000_RXDEXT_STATERR_CE  |            \
-    E1000_RXDEXT_STATERR_SE  |            \
-    E1000_RXDEXT_STATERR_SEQ |            \
-    E1000_RXDEXT_STATERR_CXE |            \
-    E1000_RXDEXT_STATERR_RXE)
+	E1000_RXDEXT_STATERR_CE  |	\
+	E1000_RXDEXT_STATERR_SE  |	\
+	E1000_RXDEXT_STATERR_SEQ |	\
+	E1000_RXDEXT_STATERR_CXE |	\
+	E1000_RXDEXT_STATERR_RXE)
 
 #define E1000_MRQC_RSS_FIELD_MASK              0xFFFF0000
 #define E1000_MRQC_RSS_FIELD_IPV4_TCP          0x00010000
@@ -253,14 +253,15 @@
 #define ADVERTISE_1000_FULL               0x0020
 
 /* 1000/H is not supported, nor spec-compliant. */
-#define E1000_ALL_SPEED_DUPLEX ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
-				ADVERTISE_100_HALF |  ADVERTISE_100_FULL | \
-						     ADVERTISE_1000_FULL)
-#define E1000_ALL_NOT_GIG      ( ADVERTISE_10_HALF |   ADVERTISE_10_FULL | \
-				ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
-#define E1000_ALL_100_SPEED    (ADVERTISE_100_HALF |  ADVERTISE_100_FULL)
-#define E1000_ALL_10_SPEED      (ADVERTISE_10_HALF |   ADVERTISE_10_FULL)
-#define E1000_ALL_HALF_DUPLEX   (ADVERTISE_10_HALF |  ADVERTISE_100_HALF)
+#define E1000_ALL_SPEED_DUPLEX	( \
+	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+	ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
+#define E1000_ALL_NOT_GIG	( \
+	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
+	ADVERTISE_100_FULL)
+#define E1000_ALL_100_SPEED	(ADVERTISE_100_HALF | ADVERTISE_100_FULL)
+#define E1000_ALL_10_SPEED	(ADVERTISE_10_HALF | ADVERTISE_10_FULL)
+#define E1000_ALL_HALF_DUPLEX	(ADVERTISE_10_HALF | ADVERTISE_100_HALF)
 
 #define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX
 
@@ -422,11 +423,11 @@
  *   o LSC    = Link Status Change
  */
 #define IMS_ENABLE_MASK ( \
-    E1000_IMS_RXT0   |    \
-    E1000_IMS_TXDW   |    \
-    E1000_IMS_RXDMT0 |    \
-    E1000_IMS_RXSEQ  |    \
-    E1000_IMS_LSC)
+	E1000_IMS_RXT0   |    \
+	E1000_IMS_TXDW   |    \
+	E1000_IMS_RXDMT0 |    \
+	E1000_IMS_RXSEQ  |    \
+	E1000_IMS_LSC)
 
 /* Interrupt Mask Set */
 #define E1000_IMS_TXDW      E1000_ICR_TXDW      /* Transmit desc written back */
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 58547b8abe3d..2ca6f2f502ea 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -4507,7 +4507,7 @@ static const struct e1000_mac_operations ich8_mac_ops = {
 	.reset_hw		= e1000_reset_hw_ich8lan,
 	.init_hw		= e1000_init_hw_ich8lan,
 	.setup_link		= e1000_setup_link_ich8lan,
-	.setup_physical_interface= e1000_setup_copper_link_ich8lan,
+	.setup_physical_interface = e1000_setup_copper_link_ich8lan,
 	/* id_led_init dependent on mac type */
 	.config_collision_dist	= e1000e_config_collision_dist_generic,
 	.rar_set		= e1000e_rar_set_generic,
@@ -4529,7 +4529,7 @@ static const struct e1000_phy_operations ich8_phy_ops = {
 
 static const struct e1000_nvm_operations ich8_nvm_ops = {
 	.acquire		= e1000_acquire_nvm_ich8lan,
-	.read		 	= e1000_read_nvm_ich8lan,
+	.read			= e1000_read_nvm_ich8lan,
 	.release		= e1000_release_nvm_ich8lan,
 	.reload			= e1000e_reload_nvm_generic,
 	.update			= e1000_update_nvm_checksum_ich8lan,
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 0709f49f0335..5992eefca54e 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1074,8 +1074,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val =
-		    e1e_rphy(hw, PHY_LP_ABILITY, &mii_nway_lp_ability_reg);
+		ret_val = e1e_rphy(hw, PHY_LP_ABILITY,
+				   &mii_nway_lp_ability_reg);
 		if (ret_val)
 			return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 46a38a4d8da5..e878dbfb9096 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -6571,8 +6571,8 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 
 	err = pci_request_selected_regions_exclusive(pdev,
-	                                  pci_select_bars(pdev, IORESOURCE_MEM),
-	                                  e1000e_driver_name);
+					  pci_select_bars(pdev, IORESOURCE_MEM),
+					  e1000e_driver_name);
 	if (err)
 		goto err_pci_reg;
 
diff --git a/drivers/net/ethernet/intel/e1000e/param.c b/drivers/net/ethernet/intel/e1000e/param.c
index 19c40d6f53cc..98da75dff936 100644
--- a/drivers/net/ethernet/intel/e1000e/param.c
+++ b/drivers/net/ethernet/intel/e1000e/param.c
@@ -53,8 +53,7 @@ MODULE_PARM_DESC(copybreak,
  */
 #define E1000_PARAM_INIT { [0 ... E1000_MAX_NIC] = OPTION_UNSET }
 #define E1000_PARAM(X, desc)					\
-	static int X[E1000_MAX_NIC+1]		\
-		= E1000_PARAM_INIT;				\
+	static int X[E1000_MAX_NIC+1] = E1000_PARAM_INIT;	\
 	static unsigned int num_##X;				\
 	module_param_array_named(X, X, int, &num_##X, 0);	\
 	MODULE_PARM_DESC(X, desc);
-- 
cgit v1.2.3


From c2ade1a41d69b8b734dd9947bf7ec25bb2fd2f33 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Wed, 16 Jan 2013 08:54:35 +0000
Subject: e1000e: use generic IEEE MII definitions

For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions.  Use those instead of redundant local
defines.

Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).

Some whitespace issues in the surrounding context of the above changes are
also cleaned up.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/80003es2lan.c |   6 +-
 drivers/net/ethernet/intel/e1000e/82571.c       |   4 +-
 drivers/net/ethernet/intel/e1000e/defines.h     |  60 --------
 drivers/net/ethernet/intel/e1000e/e1000.h       |   1 +
 drivers/net/ethernet/intel/e1000e/ethtool.c     |  24 ++--
 drivers/net/ethernet/intel/e1000e/ich8lan.c     |  10 +-
 drivers/net/ethernet/intel/e1000e/mac.c         |  31 ++--
 drivers/net/ethernet/intel/e1000e/netdev.c      |  27 ++--
 drivers/net/ethernet/intel/e1000e/phy.c         | 179 ++++++++++++------------
 9 files changed, 138 insertions(+), 204 deletions(-)

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index 765211a289d8..a00457abce69 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -624,16 +624,16 @@ static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
 
 	e_dbg("GG82563 PSCR: %X\n", phy_data);
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
 	/* Reset the phy to commit changes. */
-	phy_data |= MII_CR_RESET;
+	phy_data |= BMCR_RESET;
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index db364b69f87e..cf86090edd3b 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -447,13 +447,13 @@ static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
 		break;
 	case e1000_82574:
 	case e1000_82583:
-		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
 		if (ret_val)
 			return ret_val;
 
 		phy->id = (u32)(phy_id << 16);
 		udelay(20);
-		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
 		if (ret_val)
 			return ret_val;
 
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 1257f917af34..615b900c0152 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -563,66 +563,6 @@
 			   E1000_GCR_TXDSCW_NO_SNOOP      | \
 			   E1000_GCR_TXDSCR_NO_SNOOP)
 
-/* PHY Control Register */
-#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
-#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
-#define MII_CR_POWER_DOWN       0x0800  /* Power down */
-#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
-#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
-#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */
-#define MII_CR_SPEED_1000       0x0040
-#define MII_CR_SPEED_100        0x2000
-#define MII_CR_SPEED_10         0x0000
-
-/* PHY Status Register */
-#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
-#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
-
-/* Autoneg Advertisement Register */
-#define NWAY_AR_10T_HD_CAPS      0x0020   /* 10T   Half Duplex Capable */
-#define NWAY_AR_10T_FD_CAPS      0x0040   /* 10T   Full Duplex Capable */
-#define NWAY_AR_100TX_HD_CAPS    0x0080   /* 100TX Half Duplex Capable */
-#define NWAY_AR_100TX_FD_CAPS    0x0100   /* 100TX Full Duplex Capable */
-#define NWAY_AR_PAUSE            0x0400   /* Pause operation desired */
-#define NWAY_AR_ASM_DIR          0x0800   /* Asymmetric Pause Direction bit */
-
-/* Link Partner Ability Register (Base Page) */
-#define NWAY_LPAR_100TX_FD_CAPS  0x0100 /* LP 100TX Full Dplx Capable */
-#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
-#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
-
-/* Autoneg Expansion Register */
-#define NWAY_ER_LP_NWAY_CAPS     0x0001 /* LP has Auto Neg Capability */
-
-/* 1000BASE-T Control Register */
-#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
-#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
-					/* 0=DTE device */
-#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
-					/* 0=Configure PHY as Slave */
-#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
-					/* 0=Automatic Master/Slave config */
-
-/* 1000BASE-T Status Register */
-#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
-#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
-
-
-/* PHY 1000 MII Register/Bit Definitions */
-/* PHY Registers defined by IEEE */
-#define PHY_CONTROL      0x00 /* Control Register */
-#define PHY_STATUS       0x01 /* Status Register */
-#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
-#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
-#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
-#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */
-
-#define PHY_CONTROL_LB   0x4000 /* PHY Loopback bit */
-
 /* NVM Control */
 #define E1000_EECD_SK        0x00000001 /* NVM Clock */
 #define E1000_EECD_CS        0x00000002 /* NVM Chip Select */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index c7d5c5b92ee5..4b0bd9c225cc 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -45,6 +45,7 @@
 #include <linux/net_tstamp.h>
 #include <linux/ptp_clock_kernel.h>
 #include <linux/ptp_classify.h>
+#include <linux/mii.h>
 #include "hw.h"
 
 struct e1000_info;
diff --git a/drivers/net/ethernet/intel/e1000e/ethtool.c b/drivers/net/ethernet/intel/e1000e/ethtool.c
index b1447783ff29..c6c3e921686d 100644
--- a/drivers/net/ethernet/intel/e1000e/ethtool.c
+++ b/drivers/net/ethernet/intel/e1000e/ethtool.c
@@ -472,10 +472,10 @@ static void e1000_get_regs(struct net_device *netdev,
 		regs_buff[22] = adapter->phy_stats.receive_errors;
 		regs_buff[23] = regs_buff[13]; /* mdix mode */
 	}
-	regs_buff[21] = 0; /* was idle_errors */
-	e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
-	regs_buff[24] = (u32)phy_data;  /* phy local receiver status */
-	regs_buff[25] = regs_buff[24];  /* phy remote receiver status */
+	regs_buff[21] = 0;	/* was idle_errors */
+	e1e_rphy(hw, MII_STAT1000, &phy_data);
+	regs_buff[24] = (u32)phy_data;	/* phy local receiver status */
+	regs_buff[25] = regs_buff[24];	/* phy remote receiver status */
 }
 
 static int e1000_get_eeprom_len(struct net_device *netdev)
@@ -1284,7 +1284,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 
 	if (hw->phy.type == e1000_phy_ife) {
 		/* force 100, set loopback */
-		e1e_wphy(hw, PHY_CONTROL, 0x6100);
+		e1e_wphy(hw, MII_BMCR, 0x6100);
 
 		/* Now set up the MAC to the same speed/duplex as the PHY. */
 		ctrl_reg = er32(CTRL);
@@ -1307,9 +1307,9 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 		/* Auto-MDI/MDIX Off */
 		e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
 		/* reset to update Auto-MDI/MDIX */
-		e1e_wphy(hw, PHY_CONTROL, 0x9140);
+		e1e_wphy(hw, MII_BMCR, 0x9140);
 		/* autoneg off */
-		e1e_wphy(hw, PHY_CONTROL, 0x8140);
+		e1e_wphy(hw, MII_BMCR, 0x8140);
 		break;
 	case e1000_phy_gg82563:
 		e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x1CC);
@@ -1363,7 +1363,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 	}
 
 	/* force 1000, set loopback */
-	e1e_wphy(hw, PHY_CONTROL, 0x4140);
+	e1e_wphy(hw, MII_BMCR, 0x4140);
 	mdelay(250);
 
 	/* Now set up the MAC to the same speed/duplex as the PHY. */
@@ -1538,10 +1538,10 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter)
 		hw->mac.autoneg = 1;
 		if (hw->phy.type == e1000_phy_gg82563)
 			e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x180);
-		e1e_rphy(hw, PHY_CONTROL, &phy_reg);
-		if (phy_reg & MII_CR_LOOPBACK) {
-			phy_reg &= ~MII_CR_LOOPBACK;
-			e1e_wphy(hw, PHY_CONTROL, phy_reg);
+		e1e_rphy(hw, MII_BMCR, &phy_reg);
+		if (phy_reg & BMCR_LOOPBACK) {
+			phy_reg &= ~BMCR_LOOPBACK;
+			e1e_wphy(hw, MII_BMCR, phy_reg);
 			if (hw->phy.ops.commit)
 				hw->phy.ops.commit(hw);
 		}
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 5ca21f9b3334..a019b46f30e2 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -312,12 +312,12 @@ static bool e1000_phy_is_accessible_pchlan(struct e1000_hw *hw)
 	u16 retry_count;
 
 	for (retry_count = 0; retry_count < 2; retry_count++) {
-		ret_val = e1e_rphy_locked(hw, PHY_ID1, &phy_reg);
+		ret_val = e1e_rphy_locked(hw, MII_PHYSID1, &phy_reg);
 		if (ret_val || (phy_reg == 0xFFFF))
 			continue;
 		phy_id = (u32)(phy_reg << 16);
 
-		ret_val = e1e_rphy_locked(hw, PHY_ID2, &phy_reg);
+		ret_val = e1e_rphy_locked(hw, MII_PHYSID2, &phy_reg);
 		if (ret_val || (phy_reg == 0xFFFF)) {
 			phy_id = 0;
 			continue;
@@ -882,8 +882,8 @@ static s32 e1000_set_eee_pchlan(struct e1000_hw *hw)
 			lpi_ctrl |= I82579_LPI_CTRL_1000_ENABLE;
 
 		if (dev_spec->eee_lp_ability & I82579_EEE_100_SUPPORTED) {
-			e1e_rphy_locked(hw, PHY_LP_ABILITY, &data);
-			if (data & NWAY_LPAR_100TX_FD_CAPS)
+			e1e_rphy_locked(hw, MII_LPA, &data);
+			if (data & LPA_100FULL)
 				lpi_ctrl |= I82579_LPI_CTRL_100_ENABLE;
 			else
 				/* EEE is not supported in 100Half, so ignore
@@ -1792,7 +1792,7 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 		 */
 		if (hw->phy.revision < 2) {
 			e1000e_phy_sw_reset(hw);
-			ret_val = e1e_wphy(hw, PHY_CONTROL, 0x3140);
+			ret_val = e1e_wphy(hw, MII_BMCR, 0x3140);
 		}
 	}
 
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c
index 7365288f20f7..b78e02174601 100644
--- a/drivers/net/ethernet/intel/e1000e/mac.c
+++ b/drivers/net/ethernet/intel/e1000e/mac.c
@@ -1053,14 +1053,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 * has completed.  We read this twice because this reg has
 		 * some "sticky" (latched) bits.
 		 */
-		ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+		ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_rphy(hw, PHY_STATUS, &mii_status_reg);
+		ret_val = e1e_rphy(hw, MII_BMSR, &mii_status_reg);
 		if (ret_val)
 			return ret_val;
 
-		if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
+		if (!(mii_status_reg & BMSR_ANEGCOMPLETE)) {
 			e_dbg("Copper PHY and Auto Neg has not completed.\n");
 			return ret_val;
 		}
@@ -1071,11 +1071,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 * Page Ability Register (Address 5) to determine how
 		 * flow control was negotiated.
 		 */
-		ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg);
+		ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_nway_adv_reg);
 		if (ret_val)
 			return ret_val;
-		ret_val = e1e_rphy(hw, PHY_LP_ABILITY,
-				   &mii_nway_lp_ability_reg);
+		ret_val = e1e_rphy(hw, MII_LPA, &mii_nway_lp_ability_reg);
 		if (ret_val)
 			return ret_val;
 
@@ -1112,8 +1111,8 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *   1   |   DC    |   1   |   DC    | E1000_fc_full
 		 *
 		 */
-		if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-		    (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+		if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+		    (mii_nway_lp_ability_reg & LPA_PAUSE_CAP)) {
 			/* Now we need to check if the user selected Rx ONLY
 			 * of pause frames.  In this case, we had to advertise
 			 * FULL flow control because we could not advertise Rx
@@ -1135,10 +1134,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *-------|---------|-------|---------|--------------------
 		 *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
 		 */
-		else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+		else if (!(mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+			 (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_CAP) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) {
 			hw->fc.current_mode = e1000_fc_tx_pause;
 			e_dbg("Flow Control = Tx PAUSE frames only.\n");
 		}
@@ -1149,10 +1148,10 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
 		 *-------|---------|-------|---------|--------------------
 		 *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
 		 */
-		else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
-			 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
-			 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
-			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
+		else if ((mii_nway_adv_reg & ADVERTISE_PAUSE_CAP) &&
+			 (mii_nway_adv_reg & ADVERTISE_PAUSE_ASYM) &&
+			 !(mii_nway_lp_ability_reg & LPA_PAUSE_CAP) &&
+			 (mii_nway_lp_ability_reg & LPA_PAUSE_ASYM)) {
 			hw->fc.current_mode = e1000_fc_rx_pause;
 			e_dbg("Flow Control = Rx PAUSE frames only.\n");
 		} else {
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index eb01a55f60a6..e0eb5dddf3ea 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -42,7 +42,6 @@
 #include <linux/slab.h>
 #include <net/checksum.h>
 #include <net/ip6_checksum.h>
-#include <linux/mii.h>
 #include <linux/ethtool.h>
 #include <linux/if_vlan.h>
 #include <linux/cpu.h>
@@ -1117,9 +1116,9 @@ static void e1000_print_hw_hang(struct work_struct *work)
 	adapter->tx_hang_recheck = false;
 	netif_stop_queue(netdev);
 
-	e1e_rphy(hw, PHY_STATUS, &phy_status);
-	e1e_rphy(hw, PHY_1000T_STATUS, &phy_1000t_status);
-	e1e_rphy(hw, PHY_EXT_STATUS, &phy_ext_status);
+	e1e_rphy(hw, MII_BMSR, &phy_status);
+	e1e_rphy(hw, MII_STAT1000, &phy_1000t_status);
+	e1e_rphy(hw, MII_ESTATUS, &phy_ext_status);
 
 	pci_read_config_word(adapter->pdev, PCI_STATUS, &pci_status);
 
@@ -4677,14 +4676,14 @@ static void e1000_phy_read_status(struct e1000_adapter *adapter)
 	    (adapter->hw.phy.media_type == e1000_media_type_copper)) {
 		int ret_val;
 
-		ret_val  = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
-		ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
-		ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
-		ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
-		ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
-		ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
-		ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
-		ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
+		ret_val = e1e_rphy(hw, MII_BMCR, &phy->bmcr);
+		ret_val |= e1e_rphy(hw, MII_BMSR, &phy->bmsr);
+		ret_val |= e1e_rphy(hw, MII_ADVERTISE, &phy->advertise);
+		ret_val |= e1e_rphy(hw, MII_LPA, &phy->lpa);
+		ret_val |= e1e_rphy(hw, MII_EXPANSION, &phy->expansion);
+		ret_val |= e1e_rphy(hw, MII_CTRL1000, &phy->ctrl1000);
+		ret_val |= e1e_rphy(hw, MII_STAT1000, &phy->stat1000);
+		ret_val |= e1e_rphy(hw, MII_ESTATUS, &phy->estatus);
 		if (ret_val)
 			e_warn("Error reading PHY register\n");
 	} else {
@@ -4856,9 +4855,9 @@ static void e1000_watchdog_task(struct work_struct *work)
 			    (adapter->link_duplex == HALF_DUPLEX)) {
 				u16 autoneg_exp;
 
-				e1e_rphy(hw, PHY_AUTONEG_EXP, &autoneg_exp);
+				e1e_rphy(hw, MII_EXPANSION, &autoneg_exp);
 
-				if (!(autoneg_exp & NWAY_ER_LP_NWAY_CAPS))
+				if (!(autoneg_exp & EXPANSION_NWAY))
 					e_info("Autonegotiated half duplex but link partner cannot autoneg.  Try forcing full duplex if link gets many collisions.\n");
 			}
 
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 6f32811dbcf0..ae656f16c9fd 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -131,13 +131,13 @@ s32 e1000e_get_phy_id(struct e1000_hw *hw)
 		return 0;
 
 	while (retry_count < 2) {
-		ret_val = e1e_rphy(hw, PHY_ID1, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
 		if (ret_val)
 			return ret_val;
 
 		phy->id = (u32)(phy_id << 16);
 		udelay(20);
-		ret_val = e1e_rphy(hw, PHY_ID2, &phy_id);
+		ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
 		if (ret_val)
 			return ret_val;
 
@@ -641,31 +641,31 @@ static s32 e1000_set_master_slave_mode(struct e1000_hw *hw)
 	u16 phy_data;
 
 	/* Resolve Master/Slave mode */
-	ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_CTRL1000, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	/* load defaults for future use */
-	hw->phy.original_ms_type = (phy_data & CR_1000T_MS_ENABLE) ?
-	    ((phy_data & CR_1000T_MS_VALUE) ?
+	hw->phy.original_ms_type = (phy_data & CTL1000_ENABLE_MASTER) ?
+	    ((phy_data & CTL1000_AS_MASTER) ?
 	     e1000_ms_force_master : e1000_ms_force_slave) : e1000_ms_auto;
 
 	switch (hw->phy.ms_type) {
 	case e1000_ms_force_master:
-		phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+		phy_data |= (CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER);
 		break;
 	case e1000_ms_force_slave:
-		phy_data |= CR_1000T_MS_ENABLE;
-		phy_data &= ~(CR_1000T_MS_VALUE);
+		phy_data |= CTL1000_ENABLE_MASTER;
+		phy_data &= ~(CTL1000_AS_MASTER);
 		break;
 	case e1000_ms_auto:
-		phy_data &= ~CR_1000T_MS_ENABLE;
+		phy_data &= ~CTL1000_ENABLE_MASTER;
 		/* fall-through */
 	default:
 		break;
 	}
 
-	return e1e_wphy(hw, PHY_1000T_CTRL, phy_data);
+	return e1e_wphy(hw, MII_CTRL1000, phy_data);
 }
 
 /**
@@ -943,12 +943,12 @@ s32 e1000e_copper_link_setup_igp(struct e1000_hw *hw)
 				return ret_val;
 
 			/* Set auto Master/Slave resolution process */
-			ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &data);
+			ret_val = e1e_rphy(hw, MII_CTRL1000, &data);
 			if (ret_val)
 				return ret_val;
 
-			data &= ~CR_1000T_MS_ENABLE;
-			ret_val = e1e_wphy(hw, PHY_1000T_CTRL, data);
+			data &= ~CTL1000_ENABLE_MASTER;
+			ret_val = e1e_wphy(hw, MII_CTRL1000, data);
 			if (ret_val)
 				return ret_val;
 		}
@@ -978,13 +978,13 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	phy->autoneg_advertised &= phy->autoneg_mask;
 
 	/* Read the MII Auto-Neg Advertisement Register (Address 4). */
-	ret_val = e1e_rphy(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+	ret_val = e1e_rphy(hw, MII_ADVERTISE, &mii_autoneg_adv_reg);
 	if (ret_val)
 		return ret_val;
 
 	if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
 		/* Read the MII 1000Base-T Control Register (Address 9). */
-		ret_val = e1e_rphy(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+		ret_val = e1e_rphy(hw, MII_CTRL1000, &mii_1000t_ctrl_reg);
 		if (ret_val)
 			return ret_val;
 	}
@@ -1000,36 +1000,35 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	 * Advertisement Register (Address 4) and the 1000 mb speed bits in
 	 * the  1000Base-T Control Register (Address 9).
 	 */
-	mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
-				 NWAY_AR_100TX_HD_CAPS |
-				 NWAY_AR_10T_FD_CAPS   |
-				 NWAY_AR_10T_HD_CAPS);
-	mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+	mii_autoneg_adv_reg &= ~(ADVERTISE_100FULL |
+				 ADVERTISE_100HALF |
+				 ADVERTISE_10FULL | ADVERTISE_10HALF);
+	mii_1000t_ctrl_reg &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
 
 	e_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
 
 	/* Do we want to advertise 10 Mb Half Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
 		e_dbg("Advertise 10mb Half duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_10HALF;
 	}
 
 	/* Do we want to advertise 10 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
 		e_dbg("Advertise 10mb Full duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_10FULL;
 	}
 
 	/* Do we want to advertise 100 Mb Half Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
 		e_dbg("Advertise 100mb Half duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_100HALF;
 	}
 
 	/* Do we want to advertise 100 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
 		e_dbg("Advertise 100mb Full duplex\n");
-		mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+		mii_autoneg_adv_reg |= ADVERTISE_100FULL;
 	}
 
 	/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
@@ -1039,14 +1038,14 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 	/* Do we want to advertise 1000 Mb Full Duplex? */
 	if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
 		e_dbg("Advertise 1000mb Full duplex\n");
-		mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+		mii_1000t_ctrl_reg |= ADVERTISE_1000FULL;
 	}
 
 	/* Check for a software override of the flow control settings, and
 	 * setup the PHY advertisement registers accordingly.  If
 	 * auto-negotiation is enabled, then software will have to set the
 	 * "PAUSE" bits to the correct value in the Auto-Negotiation
-	 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+	 * Advertisement Register (MII_ADVERTISE) and re-start auto-
 	 * negotiation.
 	 *
 	 * The possible values of the "fc" parameter are:
@@ -1064,7 +1063,8 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 		/* Flow control (Rx & Tx) is completely disabled by a
 		 * software over-ride.
 		 */
-		mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg &=
+		    ~(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	case e1000_fc_rx_pause:
 		/* Rx Flow control is enabled, and Tx Flow control is
@@ -1076,34 +1076,36 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
 		 * (in e1000e_config_fc_after_link_up) we will disable the
 		 * hw's ability to send PAUSE frames.
 		 */
-		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg |=
+		    (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	case e1000_fc_tx_pause:
 		/* Tx Flow control is enabled, and Rx Flow control is
 		 * disabled, by a software over-ride.
 		 */
-		mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
-		mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+		mii_autoneg_adv_reg |= ADVERTISE_PAUSE_ASYM;
+		mii_autoneg_adv_reg &= ~ADVERTISE_PAUSE_CAP;
 		break;
 	case e1000_fc_full:
 		/* Flow control (both Rx and Tx) is enabled by a software
 		 * over-ride.
 		 */
-		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		mii_autoneg_adv_reg |=
+		    (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
 		break;
 	default:
 		e_dbg("Flow control param set incorrectly\n");
 		return -E1000_ERR_CONFIG;
 	}
 
-	ret_val = e1e_wphy(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+	ret_val = e1e_wphy(hw, MII_ADVERTISE, mii_autoneg_adv_reg);
 	if (ret_val)
 		return ret_val;
 
 	e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
 
 	if (phy->autoneg_mask & ADVERTISE_1000_FULL)
-		ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+		ret_val = e1e_wphy(hw, MII_CTRL1000, mii_1000t_ctrl_reg);
 
 	return ret_val;
 }
@@ -1145,12 +1147,12 @@ static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
 	/* Restart auto-negotiation by setting the Auto Neg Enable bit and
 	 * the Auto Neg Restart bit in the PHY control register.
 	 */
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
-	phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+	phy_ctrl |= (BMCR_ANENABLE | BMCR_ANRESTART);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
@@ -1237,13 +1239,13 @@ s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw)
 	u16 phy_data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -1315,13 +1317,13 @@ s32 e1000e_phy_force_speed_duplex_m88(struct e1000_hw *hw)
 
 	e_dbg("M88E1000 PSCR: %X\n", phy_data);
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -1408,13 +1410,13 @@ s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw)
 	u16 data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, data);
+	ret_val = e1e_wphy(hw, MII_BMCR, data);
 	if (ret_val)
 		return ret_val;
 
@@ -1458,13 +1460,13 @@ s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw)
 /**
  *  e1000e_phy_force_speed_duplex_setup - Configure forced PHY speed/duplex
  *  @hw: pointer to the HW structure
- *  @phy_ctrl: pointer to current value of PHY_CONTROL
+ *  @phy_ctrl: pointer to current value of MII_BMCR
  *
  *  Forces speed and duplex on the PHY by doing the following: disable flow
  *  control, force speed/duplex on the MAC, disable auto speed detection,
  *  disable auto-negotiation, configure duplex, configure speed, configure
  *  the collision distance, write configuration to CTRL register.  The
- *  caller must write to the PHY_CONTROL register for these settings to
+ *  caller must write to the MII_BMCR register for these settings to
  *  take affect.
  **/
 void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
@@ -1484,29 +1486,28 @@ void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl)
 	ctrl &= ~E1000_CTRL_ASDE;
 
 	/* Disable autoneg on the phy */
-	*phy_ctrl &= ~MII_CR_AUTO_NEG_EN;
+	*phy_ctrl &= ~BMCR_ANENABLE;
 
 	/* Forcing Full or Half Duplex? */
 	if (mac->forced_speed_duplex & E1000_ALL_HALF_DUPLEX) {
 		ctrl &= ~E1000_CTRL_FD;
-		*phy_ctrl &= ~MII_CR_FULL_DUPLEX;
+		*phy_ctrl &= ~BMCR_FULLDPLX;
 		e_dbg("Half Duplex\n");
 	} else {
 		ctrl |= E1000_CTRL_FD;
-		*phy_ctrl |= MII_CR_FULL_DUPLEX;
+		*phy_ctrl |= BMCR_FULLDPLX;
 		e_dbg("Full Duplex\n");
 	}
 
 	/* Forcing 10mb or 100mb? */
 	if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) {
 		ctrl |= E1000_CTRL_SPD_100;
-		*phy_ctrl |= MII_CR_SPEED_100;
-		*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+		*phy_ctrl |= BMCR_SPEED100;
+		*phy_ctrl &= ~BMCR_SPEED1000;
 		e_dbg("Forcing 100mb\n");
 	} else {
 		ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
-		*phy_ctrl |= MII_CR_SPEED_10;
-		*phy_ctrl &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+		*phy_ctrl &= ~(BMCR_SPEED1000 | BMCR_SPEED100);
 		e_dbg("Forcing 10mb\n");
 	}
 
@@ -1747,13 +1748,13 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw)
 
 	/* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
 	for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		if (phy_status & MII_SR_AUTONEG_COMPLETE)
+		if (phy_status & BMSR_ANEGCOMPLETE)
 			break;
 		msleep(100);
 	}
@@ -1780,21 +1781,21 @@ s32 e1000e_phy_has_link_generic(struct e1000_hw *hw, u32 iterations,
 	u16 i, phy_status;
 
 	for (i = 0; i < iterations; i++) {
-		/* Some PHYs require the PHY_STATUS register to be read
+		/* Some PHYs require the MII_BMSR register to be read
 		 * twice due to the link bit being sticky.  No harm doing
 		 * it across the board.
 		 */
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			/* If the first read fails, another entity may have
 			 * ownership of the resources, wait and try again to
 			 * see if they have relinquished the resources yet.
 			 */
 			udelay(usec_interval);
-		ret_val = e1e_rphy(hw, PHY_STATUS, &phy_status);
+		ret_val = e1e_rphy(hw, MII_BMSR, &phy_status);
 		if (ret_val)
 			break;
-		if (phy_status & MII_SR_LINK_STATUS)
+		if (phy_status & BMSR_LSTATUS)
 			break;
 		if (usec_interval >= 1000)
 			mdelay(usec_interval/1000);
@@ -1968,17 +1969,15 @@ s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &phy_data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &phy_data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (phy_data & SR_1000T_LOCAL_RX_STATUS)
-				? e1000_1000t_rx_status_ok
-				: e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (phy_data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (phy_data & SR_1000T_REMOTE_RX_STATUS)
-				 ? e1000_1000t_rx_status_ok
-				 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (phy_data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		/* Set values to "undefined" */
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
@@ -2032,17 +2031,15 @@ s32 e1000e_get_phy_info_igp(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
-				? e1000_1000t_rx_status_ok
-				: e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
-				 ? e1000_1000t_rx_status_ok
-				 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
 		phy->local_rx = e1000_1000t_rx_status_undefined;
@@ -2116,12 +2113,12 @@ s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 phy_ctrl;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_ctrl);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
-	phy_ctrl |= MII_CR_RESET;
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_ctrl);
+	phy_ctrl |= BMCR_RESET;
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_ctrl);
 	if (ret_val)
 		return ret_val;
 
@@ -2751,9 +2748,9 @@ void e1000_power_up_phy_copper(struct e1000_hw *hw)
 	u16 mii_reg = 0;
 
 	/* The PHY will retain its settings across a power down/up cycle */
-	e1e_rphy(hw, PHY_CONTROL, &mii_reg);
-	mii_reg &= ~MII_CR_POWER_DOWN;
-	e1e_wphy(hw, PHY_CONTROL, mii_reg);
+	e1e_rphy(hw, MII_BMCR, &mii_reg);
+	mii_reg &= ~BMCR_PDOWN;
+	e1e_wphy(hw, MII_BMCR, mii_reg);
 }
 
 /**
@@ -2769,9 +2766,9 @@ void e1000_power_down_phy_copper(struct e1000_hw *hw)
 	u16 mii_reg = 0;
 
 	/* The PHY will retain its settings across a power down/up cycle */
-	e1e_rphy(hw, PHY_CONTROL, &mii_reg);
-	mii_reg |= MII_CR_POWER_DOWN;
-	e1e_wphy(hw, PHY_CONTROL, mii_reg);
+	e1e_rphy(hw, MII_BMCR, &mii_reg);
+	mii_reg |= BMCR_PDOWN;
+	e1e_wphy(hw, MII_BMCR, mii_reg);
 	usleep_range(1000, 2000);
 }
 
@@ -3087,8 +3084,8 @@ s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw)
 		return 0;
 
 	/* Do not apply workaround if in PHY loopback bit 14 set */
-	e1e_rphy(hw, PHY_CONTROL, &data);
-	if (data & PHY_CONTROL_LB)
+	e1e_rphy(hw, MII_BMCR, &data);
+	if (data & BMCR_LOOPBACK)
 		return 0;
 
 	/* check if link is up and at 1Gbps */
@@ -3152,13 +3149,13 @@ s32 e1000_phy_force_speed_duplex_82577(struct e1000_hw *hw)
 	u16 phy_data;
 	bool link;
 
-	ret_val = e1e_rphy(hw, PHY_CONTROL, &phy_data);
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
 	if (ret_val)
 		return ret_val;
 
 	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
 
-	ret_val = e1e_wphy(hw, PHY_CONTROL, phy_data);
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
 	if (ret_val)
 		return ret_val;
 
@@ -3226,17 +3223,15 @@ s32 e1000_get_phy_info_82577(struct e1000_hw *hw)
 		if (ret_val)
 			return ret_val;
 
-		ret_val = e1e_rphy(hw, PHY_1000T_STATUS, &data);
+		ret_val = e1e_rphy(hw, MII_STAT1000, &data);
 		if (ret_val)
 			return ret_val;
 
-		phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS)
-		                ? e1000_1000t_rx_status_ok
-		                : e1000_1000t_rx_status_not_ok;
+		phy->local_rx = (data & LPA_1000LOCALRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 
-		phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS)
-		                 ? e1000_1000t_rx_status_ok
-		                 : e1000_1000t_rx_status_not_ok;
+		phy->remote_rx = (data & LPA_1000REMRXOK)
+		    ? e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
 	} else {
 		phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED;
 		phy->local_rx = e1000_1000t_rx_status_undefined;
-- 
cgit v1.2.3


From f25701df2ef171894730534e5b557186d2bacf17 Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:04 +0000
Subject: e1000e: cosmetic move of #defines and prototypes to the new 82571.h

Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names).  These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/82571.c   | 15 --------
 drivers/net/ethernet/intel/e1000e/82571.h   | 58 +++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/defines.h |  2 -
 drivers/net/ethernet/intel/e1000e/e1000.h   |  4 --
 drivers/net/ethernet/intel/e1000e/hw.h      |  5 +--
 drivers/net/ethernet/intel/e1000e/netdev.c  |  1 -
 6 files changed, 60 insertions(+), 25 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/82571.h

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/82571.c b/drivers/net/ethernet/intel/e1000e/82571.c
index cf86090edd3b..1db7e3df43ea 100644
--- a/drivers/net/ethernet/intel/e1000e/82571.c
+++ b/drivers/net/ethernet/intel/e1000e/82571.c
@@ -44,21 +44,6 @@
 
 #include "e1000.h"
 
-#define ID_LED_RESERVED_F746 0xF746
-#define ID_LED_DEFAULT_82573 ((ID_LED_DEF1_DEF2 << 12) | \
-			      (ID_LED_OFF1_ON2  <<  8) | \
-			      (ID_LED_DEF1_DEF2 <<  4) | \
-			      (ID_LED_DEF1_DEF2))
-
-#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
-#define AN_RETRY_COUNT          5 /* Autoneg Retry Count value */
-#define E1000_BASE1000T_STATUS          10
-#define E1000_IDLE_ERROR_COUNT_MASK     0xFF
-#define E1000_RECEIVE_ERROR_COUNTER     21
-#define E1000_RECEIVE_ERROR_MAX         0xFFFF
-
-#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
-
 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
diff --git a/drivers/net/ethernet/intel/e1000e/82571.h b/drivers/net/ethernet/intel/e1000e/82571.h
new file mode 100644
index 000000000000..85cb1a3b7cd4
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/82571.h
@@ -0,0 +1,58 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_82571_H_
+#define _E1000E_82571_H_
+
+#define ID_LED_RESERVED_F746	0xF746
+#define ID_LED_DEFAULT_82573	((ID_LED_DEF1_DEF2 << 12) | \
+				 (ID_LED_OFF1_ON2  <<  8) | \
+				 (ID_LED_DEF1_DEF2 <<  4) | \
+				 (ID_LED_DEF1_DEF2))
+
+#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX	0x08000000
+#define AN_RETRY_COUNT		5	/* Autoneg Retry Count value */
+
+/* Intr Throttling - RW */
+#define E1000_EITR_82574(_n)	(0x000E8 + (0x4 * (_n)))
+
+#define E1000_EIAC_82574	0x000DC	/* Ext. Interrupt Auto Clear - RW */
+#define E1000_EIAC_MASK_82574	0x01F00000
+
+/* Manageability Operation Mode mask */
+#define E1000_NVM_INIT_CTRL2_MNGM	0x6000
+
+#define E1000_BASE1000T_STATUS		10
+#define E1000_IDLE_ERROR_COUNT_MASK	0xFF
+#define E1000_RECEIVE_ERROR_COUNTER	21
+#define E1000_RECEIVE_ERROR_MAX		0xFFFF
+bool e1000_check_phy_82574(struct e1000_hw *hw);
+bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
+void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
+
+#endif
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index 615b900c0152..b425544144ec 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -606,8 +606,6 @@
 #define NVM_ALT_MAC_ADDR_PTR       0x0037
 #define NVM_CHECKSUM_REG           0x003F
 
-#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */
-
 #define E1000_NVM_CFG_DONE_PORT_0  0x40000 /* MNG config cycle done */
 #define E1000_NVM_CFG_DONE_PORT_1  0x80000 /* ...for second port */
 
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 4b0bd9c225cc..12c5d4043505 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -579,9 +579,6 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern bool e1000e_get_laa_state_82571(struct e1000_hw *hw);
-extern void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state);
-
 extern void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
 extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
 						 bool state);
@@ -703,7 +700,6 @@ extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
-extern bool e1000_check_phy_82574(struct e1000_hw *hw);
 extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index f32b19af9a72..6f94437d8c0e 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -54,12 +54,9 @@ enum e1e_registers {
 	E1000_ICS      = 0x000C8, /* Interrupt Cause Set - WO */
 	E1000_IMS      = 0x000D0, /* Interrupt Mask Set - RW */
 	E1000_IMC      = 0x000D8, /* Interrupt Mask Clear - WO */
-	E1000_EIAC_82574 = 0x000DC, /* Ext. Interrupt Auto Clear - RW */
 	E1000_IAM      = 0x000E0, /* Interrupt Acknowledge Auto Mask */
 	E1000_IVAR     = 0x000E4, /* Interrupt Vector Allocation - RW */
 	E1000_FEXTNVM7  = 0x000E4, /* Future Extended NVM 7 - RW */
-	E1000_EITR_82574_BASE = 0x000E8, /* Interrupt Throttling - RW */
-#define E1000_EITR_82574(_n) (E1000_EITR_82574_BASE + (_n << 2))
 	E1000_LPIC     = 0x000FC, /* Low Power Idle Control - RW */
 	E1000_RCTL     = 0x00100, /* Rx Control - RW */
 	E1000_FCTTV    = 0x00170, /* Flow Control Transmit Timer Value - RW */
@@ -1005,4 +1002,6 @@ struct e1000_hw {
 	} dev_spec;
 };
 
+#include "82571.h"
+
 #endif
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index e0eb5dddf3ea..6fcf9e8008c0 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -2024,7 +2024,6 @@ static void e1000_configure_msix(struct e1000_adapter *adapter)
 	ctrl_ext |= E1000_CTRL_EXT_PBA_CLR;
 
 	/* Auto-Mask Other interrupts upon ICR read */
-#define E1000_EIAC_MASK_82574   0x01F00000
 	ew32(IAM, ~E1000_EIAC_MASK_82574 | E1000_IMS_OTHER);
 	ctrl_ext |= E1000_CTRL_EXT_EIAME;
 	ew32(CTRL_EXT, ctrl_ext);
-- 
cgit v1.2.3


From 1b41db37f40dc682ee5d6fb47b3af545c3eabd1f Mon Sep 17 00:00:00 2001
From: Bruce Allan <bruce.w.allan@intel.com>
Date: Tue, 22 Jan 2013 08:44:14 +0000
Subject: e1000e: cosmetic move of #defines and prototypes to the new ich8lan.h

Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names).  These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
 drivers/net/ethernet/intel/e1000e/defines.h |  36 ----
 drivers/net/ethernet/intel/e1000e/e1000.h   |  53 ------
 drivers/net/ethernet/intel/e1000e/hw.h      |  13 +-
 drivers/net/ethernet/intel/e1000e/ich8lan.c | 126 -------------
 drivers/net/ethernet/intel/e1000e/ich8lan.h | 268 ++++++++++++++++++++++++++++
 drivers/net/ethernet/intel/e1000e/phy.c     |   4 -
 6 files changed, 270 insertions(+), 230 deletions(-)
 create mode 100644 drivers/net/ethernet/intel/e1000e/ich8lan.h

(limited to 'drivers/net/ethernet/intel/e1000e/defines.h')

diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h
index b425544144ec..fc3a4fe1ac71 100644
--- a/drivers/net/ethernet/intel/e1000e/defines.h
+++ b/drivers/net/ethernet/intel/e1000e/defines.h
@@ -749,38 +749,6 @@
 /* BME1000 PHY Specific Control Register */
 #define BME1000_PSCR_ENABLE_DOWNSHIFT   0x0800 /* 1 = enable downshift */
 
-/* PHY Low Power Idle Control */
-#define I82579_LPI_CTRL				PHY_REG(772, 20)
-#define I82579_LPI_CTRL_100_ENABLE		0x2000
-#define I82579_LPI_CTRL_1000_ENABLE		0x4000
-#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
-#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
-
-/* Extended Management Interface (EMI) Registers */
-#define I82579_EMI_ADDR		0x10
-#define I82579_EMI_DATA		0x11
-#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
-#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
-#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
-#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
-#define I82579_EEE_PCS_STATUS	0x182D	/* IEEE MMD Register 3.1 >> 8 */
-#define I82579_EEE_CAPABILITY	0x0410	/* IEEE MMD Register 3.20 */
-#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
-#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
-#define I82579_EEE_100_SUPPORTED	(1 << 1) /* 100BaseTx EEE supported */
-#define I82579_EEE_1000_SUPPORTED	(1 << 2) /* 1000BaseTx EEE supported */
-#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
-#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
-#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
-#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
-
-#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
-#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
-
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
-                           ((reg) & MAX_PHY_REG_ADDRESS))
-
 /* Bits...
  * 15-5: page
  * 4-0: register offset
@@ -827,8 +795,4 @@
 /* SerDes Control */
 #define E1000_GEN_POLL_TIMEOUT          640
 
-/* FW Semaphore */
-#define E1000_FWSM_WLOCK_MAC_MASK	0x0380
-#define E1000_FWSM_WLOCK_MAC_SHIFT	7
-
 #endif /* _E1000_DEFINES_H_ */
diff --git a/drivers/net/ethernet/intel/e1000e/e1000.h b/drivers/net/ethernet/intel/e1000e/e1000.h
index 12c5d4043505..7a383cd715d6 100644
--- a/drivers/net/ethernet/intel/e1000e/e1000.h
+++ b/drivers/net/ethernet/intel/e1000e/e1000.h
@@ -104,44 +104,6 @@ struct e1000_info;
 	 (((page) & 0xFFFF) << PHY_PAGE_SHIFT) |\
 	 (((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
 
-/* PHY Wakeup Registers and defines */
-#define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17)
-#define BM_RCTL         PHY_REG(BM_WUC_PAGE, 0)
-#define BM_WUC          PHY_REG(BM_WUC_PAGE, 1)
-#define BM_WUFC         PHY_REG(BM_WUC_PAGE, 2)
-#define BM_WUS          PHY_REG(BM_WUC_PAGE, 3)
-#define BM_RAR_L(_i)    (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
-#define BM_RAR_M(_i)    (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
-#define BM_RAR_H(_i)    (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
-#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
-#define BM_MTA(_i)      (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
-
-#define BM_RCTL_UPE           0x0001          /* Unicast Promiscuous Mode */
-#define BM_RCTL_MPE           0x0002          /* Multicast Promiscuous Mode */
-#define BM_RCTL_MO_SHIFT      3               /* Multicast Offset Shift */
-#define BM_RCTL_MO_MASK       (3 << 3)        /* Multicast Offset Mask */
-#define BM_RCTL_BAM           0x0020          /* Broadcast Accept Mode */
-#define BM_RCTL_PMCF          0x0040          /* Pass MAC Control Frames */
-#define BM_RCTL_RFCE          0x0080          /* Rx Flow Control Enable */
-
-#define HV_STATS_PAGE	778
-#define HV_SCC_UPPER	PHY_REG(HV_STATS_PAGE, 16) /* Single Collision Count */
-#define HV_SCC_LOWER	PHY_REG(HV_STATS_PAGE, 17)
-#define HV_ECOL_UPPER	PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. Count */
-#define HV_ECOL_LOWER	PHY_REG(HV_STATS_PAGE, 19)
-#define HV_MCC_UPPER	PHY_REG(HV_STATS_PAGE, 20) /* Multiple Coll. Count */
-#define HV_MCC_LOWER	PHY_REG(HV_STATS_PAGE, 21)
-#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision Count */
-#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
-#define HV_COLC_UPPER	PHY_REG(HV_STATS_PAGE, 25) /* Collision Count */
-#define HV_COLC_LOWER	PHY_REG(HV_STATS_PAGE, 26)
-#define HV_DC_UPPER	PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */
-#define HV_DC_LOWER	PHY_REG(HV_STATS_PAGE, 28)
-#define HV_TNCRS_UPPER	PHY_REG(HV_STATS_PAGE, 29) /* Transmit with no CRS */
-#define HV_TNCRS_LOWER	PHY_REG(HV_STATS_PAGE, 30)
-
-#define E1000_FCRTV_PCH     0x05F40 /* PCH Flow Control Refresh Timer Value */
-
 /* BM PHY Copper Specific Status */
 #define BM_CS_STATUS                      17
 #define BM_CS_STATUS_LINK_UP              0x0400
@@ -156,9 +118,6 @@ struct e1000_info;
 #define HV_M_STATUS_SPEED_1000            0x0200
 #define HV_M_STATUS_LINK_UP               0x0040
 
-#define E1000_ICH_FWSM_PCIM2PCI		0x01000000 /* ME PCIm-to-PCI active */
-#define E1000_ICH_FWSM_PCIM2PCI_COUNT	2000
-
 /* Time to wait before putting the device into D3 if there's no link (in ms). */
 #define LINK_TIMEOUT		100
 
@@ -579,17 +538,6 @@ extern s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num,
 
 extern bool e1000e_enable_mng_pass_thru(struct e1000_hw *hw);
 
-extern void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
-extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
-						 bool state);
-extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
-extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
-extern void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
-extern void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
-extern s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
-extern s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
-extern void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
-
 extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw);
 extern s32 e1000e_check_for_serdes_link(struct e1000_hw *hw);
@@ -700,7 +648,6 @@ extern s32 e1000_get_phy_info_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_ife(struct e1000_hw *hw);
 extern s32 e1000_phy_force_speed_duplex_ife(struct e1000_hw *hw);
 extern s32 e1000_check_polarity_igp(struct e1000_hw *hw);
-extern s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
 extern void e1000e_ptp_init(struct e1000_adapter *adapter);
 extern void e1000e_ptp_remove(struct e1000_adapter *adapter);
 
diff --git a/drivers/net/ethernet/intel/e1000e/hw.h b/drivers/net/ethernet/intel/e1000e/hw.h
index 8a145f468721..21a9cc36e467 100644
--- a/drivers/net/ethernet/intel/e1000e/hw.h
+++ b/drivers/net/ethernet/intel/e1000e/hw.h
@@ -200,10 +200,6 @@ enum e1e_registers {
 #define E1000_RA        (E1000_RAL(0))
 	E1000_RAH_BASE = 0x05404, /* Receive Address High - RW */
 #define E1000_RAH(_n)   (E1000_RAH_BASE + ((_n) * 8))
-	E1000_SHRAL_PCH_LPT_BASE = 0x05408,
-#define E1000_SHRAL_PCH_LPT(_n)   (E1000_SHRAL_PCH_LPT_BASE + ((_n) * 8))
-	E1000_SHRAH_PCH_LTP_BASE = 0x0540C,
-#define E1000_SHRAH_PCH_LPT(_n)   (E1000_SHRAH_PCH_LTP_BASE + ((_n) * 8))
 	E1000_SHRAL_BASE = 0x05438, /* Shared Receive Address Low - RW */
 #define E1000_SHRAL(_n)   (E1000_SHRAL_BASE + ((_n) * 8))
 	E1000_SHRAH_BASE = 0x0543C, /* Shared Receive Address High - RW */
@@ -215,6 +211,7 @@ enum e1e_registers {
 	E1000_MRQC     = 0x05818, /* Multiple Receive Control - RW */
 	E1000_MANC     = 0x05820, /* Management Control - RW */
 	E1000_FFLT     = 0x05F00, /* Flexible Filter Length Table - RW Array */
+	E1000_CRC_OFFSET = 0x05F50, /* CRC Offset register */
 	E1000_HOST_IF  = 0x08800, /* Host Interface */
 
 	E1000_KMRNCTRLSTA = 0x00034, /* MAC-PHY interface - RW */
@@ -233,9 +230,6 @@ enum e1e_registers {
 	E1000_RSSRK_BASE = 0x05C80, /* RSS Random Key - RW */
 #define E1000_RSSRK(_n)	(E1000_RSSRK_BASE + ((_n) * 4))
 	E1000_FFLT_DBG  = 0x05F04, /* Debug Register */
-	E1000_PCH_RAICC_BASE = 0x05F50, /* Receive Address Initial CRC */
-#define E1000_PCH_RAICC(_n)	(E1000_PCH_RAICC_BASE + ((_n) * 4))
-#define E1000_CRC_OFFSET	E1000_PCH_RAICC_BASE
 	E1000_HICR      = 0x08F00, /* Host Interface Control */
 	E1000_SYSTIML   = 0x0B600, /* System time register Low - RO */
 	E1000_SYSTIMH   = 0x0B604, /* System time register High - RO */
@@ -272,10 +266,6 @@ enum e1e_registers {
 #define BM_WUC_HOST_WU_BIT		(1 << 4)
 #define BM_WUC_ME_WU_BIT		(1 << 5)
 
-#define BM_WUC	PHY_REG(BM_WUC_PAGE, 1)
-#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
-#define BM_WUS	PHY_REG(BM_WUC_PAGE, 3)
-
 #define IGP01E1000_PHY_PCS_INIT_REG	0x00B4
 #define IGP01E1000_PHY_POLARITY_MASK	0x0078
 
@@ -1004,5 +994,6 @@ struct e1000_hw {
 
 #include "82571.h"
 #include "80003es2lan.h"
+#include "ich8lan.h"
 
 #endif
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index a019b46f30e2..1e838b235e8a 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -57,132 +57,6 @@
 
 #include "e1000.h"
 
-#define ICH_FLASH_GFPREG		0x0000
-#define ICH_FLASH_HSFSTS		0x0004
-#define ICH_FLASH_HSFCTL		0x0006
-#define ICH_FLASH_FADDR			0x0008
-#define ICH_FLASH_FDATA0		0x0010
-#define ICH_FLASH_PR0			0x0074
-
-#define ICH_FLASH_READ_COMMAND_TIMEOUT	500
-#define ICH_FLASH_WRITE_COMMAND_TIMEOUT	500
-#define ICH_FLASH_ERASE_COMMAND_TIMEOUT	3000000
-#define ICH_FLASH_LINEAR_ADDR_MASK	0x00FFFFFF
-#define ICH_FLASH_CYCLE_REPEAT_COUNT	10
-
-#define ICH_CYCLE_READ			0
-#define ICH_CYCLE_WRITE			2
-#define ICH_CYCLE_ERASE			3
-
-#define FLASH_GFPREG_BASE_MASK		0x1FFF
-#define FLASH_SECTOR_ADDR_SHIFT		12
-
-#define ICH_FLASH_SEG_SIZE_256		256
-#define ICH_FLASH_SEG_SIZE_4K		4096
-#define ICH_FLASH_SEG_SIZE_8K		8192
-#define ICH_FLASH_SEG_SIZE_64K		65536
-
-
-#define E1000_ICH_FWSM_RSPCIPHY	0x00000040 /* Reset PHY on PCI Reset */
-/* FW established a valid mode */
-#define E1000_ICH_FWSM_FW_VALID		0x00008000
-
-#define E1000_ICH_MNG_IAMT_MODE		0x2
-
-#define ID_LED_DEFAULT_ICH8LAN  ((ID_LED_DEF1_DEF2 << 12) | \
-				 (ID_LED_DEF1_OFF2 <<  8) | \
-				 (ID_LED_DEF1_ON2  <<  4) | \
-				 (ID_LED_DEF1_DEF2))
-
-#define E1000_ICH_NVM_SIG_WORD		0x13
-#define E1000_ICH_NVM_SIG_MASK		0xC000
-#define E1000_ICH_NVM_VALID_SIG_MASK    0xC0
-#define E1000_ICH_NVM_SIG_VALUE         0x80
-
-#define E1000_ICH8_LAN_INIT_TIMEOUT	1500
-
-#define E1000_FEXTNVM_SW_CONFIG		1
-#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M :/ */
-
-#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK    0x0C000000
-#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC  0x08000000
-
-#define E1000_FEXTNVM4_BEACON_DURATION_MASK    0x7
-#define E1000_FEXTNVM4_BEACON_DURATION_8USEC   0x7
-#define E1000_FEXTNVM4_BEACON_DURATION_16USEC  0x3
-
-#define PCIE_ICH8_SNOOP_ALL		PCIE_NO_SNOOP_ALL
-
-#define E1000_ICH_RAR_ENTRIES		7
-#define E1000_PCH2_RAR_ENTRIES		5 /* RAR[0], SHRA[0-3] */
-#define E1000_PCH_LPT_RAR_ENTRIES	12 /* RAR[0], SHRA[0-10] */
-
-#define PHY_PAGE_SHIFT 5
-#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
-			   ((reg) & MAX_PHY_REG_ADDRESS))
-#define IGP3_KMRN_DIAG  PHY_REG(770, 19) /* KMRN Diagnostic */
-#define IGP3_VR_CTRL    PHY_REG(776, 18) /* Voltage Regulator Control */
-
-#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS	0x0002
-#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
-#define IGP3_VR_CTRL_MODE_SHUTDOWN	0x0200
-
-#define HV_LED_CONFIG		PHY_REG(768, 30) /* LED Configuration */
-
-#define SW_FLAG_TIMEOUT    1000 /* SW Semaphore flag timeout in milliseconds */
-
-/* SMBus Control Phy Register */
-#define CV_SMB_CTRL		PHY_REG(769, 23)
-#define CV_SMB_CTRL_FORCE_SMBUS	0x0001
-
-/* SMBus Address Phy Register */
-#define HV_SMB_ADDR            PHY_REG(768, 26)
-#define HV_SMB_ADDR_MASK       0x007F
-#define HV_SMB_ADDR_PEC_EN     0x0200
-#define HV_SMB_ADDR_VALID      0x0080
-#define HV_SMB_ADDR_FREQ_MASK           0x1100
-#define HV_SMB_ADDR_FREQ_LOW_SHIFT      8
-#define HV_SMB_ADDR_FREQ_HIGH_SHIFT     12
-
-/* PHY Power Management Control */
-#define HV_PM_CTRL		PHY_REG(770, 17)
-#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
-
-/* Intel Rapid Start Technology Support */
-#define I217_PROXY_CTRL                 BM_PHY_REG(BM_WUC_PAGE, 70)
-#define I217_PROXY_CTRL_AUTO_DISABLE    0x0080
-#define I217_SxCTRL                     PHY_REG(BM_PORT_CTRL_PAGE, 28)
-#define I217_SxCTRL_ENABLE_LPI_RESET    0x1000
-#define I217_CGFREG                     PHY_REG(772, 29)
-#define I217_CGFREG_ENABLE_MTA_RESET    0x0002
-#define I217_MEMPWR                     PHY_REG(772, 26)
-#define I217_MEMPWR_DISABLE_SMB_RELEASE 0x0010
-
-/* Strapping Option Register - RO */
-#define E1000_STRAP                     0x0000C
-#define E1000_STRAP_SMBUS_ADDRESS_MASK  0x00FE0000
-#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
-#define E1000_STRAP_SMT_FREQ_MASK       0x00003000
-#define E1000_STRAP_SMT_FREQ_SHIFT      12
-
-/* OEM Bits Phy Register */
-#define HV_OEM_BITS            PHY_REG(768, 25)
-#define HV_OEM_BITS_LPLU       0x0004 /* Low Power Link Up */
-#define HV_OEM_BITS_GBE_DIS    0x0040 /* Gigabit Disable */
-#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
-
-#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
-#define E1000_NVM_K1_ENABLE 0x1  /* NVM Enable K1 bit */
-
-/* KMRN Mode Control */
-#define HV_KMRN_MODE_CTRL      PHY_REG(769, 16)
-#define HV_KMRN_MDIO_SLOW      0x0400
-
-/* KMRN FIFO Control and Status */
-#define HV_KMRN_FIFO_CTRLSTA                  PHY_REG(770, 16)
-#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK    0x7000
-#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT   12
-
 /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
 /* Offset 04h HSFSTS */
 union ich8_hws_flash_status {
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.h b/drivers/net/ethernet/intel/e1000e/ich8lan.h
new file mode 100644
index 000000000000..b6d3174d7d2d
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.h
@@ -0,0 +1,268 @@
+/*******************************************************************************
+
+  Intel PRO/1000 Linux driver
+  Copyright(c) 1999 - 2013 Intel Corporation.
+
+  This program is free software; you can redistribute it and/or modify it
+  under the terms and conditions of the GNU General Public License,
+  version 2, as published by the Free Software Foundation.
+
+  This program is distributed in the hope it will be useful, but WITHOUT
+  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+  more details.
+
+  You should have received a copy of the GNU General Public License along with
+  this program; if not, write to the Free Software Foundation, Inc.,
+  51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+
+  The full GNU General Public License is included in this distribution in
+  the file called "COPYING".
+
+  Contact Information:
+  Linux NICS <linux.nics@intel.com>
+  e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
+  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
+
+*******************************************************************************/
+
+#ifndef _E1000E_ICH8LAN_H_
+#define _E1000E_ICH8LAN_H_
+
+#define ICH_FLASH_GFPREG		0x0000
+#define ICH_FLASH_HSFSTS		0x0004
+#define ICH_FLASH_HSFCTL		0x0006
+#define ICH_FLASH_FADDR			0x0008
+#define ICH_FLASH_FDATA0		0x0010
+#define ICH_FLASH_PR0			0x0074
+
+/* Requires up to 10 seconds when MNG might be accessing part. */
+#define ICH_FLASH_READ_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_WRITE_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_ERASE_COMMAND_TIMEOUT	10000000
+#define ICH_FLASH_LINEAR_ADDR_MASK	0x00FFFFFF
+#define ICH_FLASH_CYCLE_REPEAT_COUNT	10
+
+#define ICH_CYCLE_READ			0
+#define ICH_CYCLE_WRITE			2
+#define ICH_CYCLE_ERASE			3
+
+#define FLASH_GFPREG_BASE_MASK		0x1FFF
+#define FLASH_SECTOR_ADDR_SHIFT		12
+
+#define ICH_FLASH_SEG_SIZE_256		256
+#define ICH_FLASH_SEG_SIZE_4K		4096
+#define ICH_FLASH_SEG_SIZE_8K		8192
+#define ICH_FLASH_SEG_SIZE_64K		65536
+
+#define E1000_ICH_FWSM_RSPCIPHY	0x00000040	/* Reset PHY on PCI Reset */
+/* FW established a valid mode */
+#define E1000_ICH_FWSM_FW_VALID	0x00008000
+#define E1000_ICH_FWSM_PCIM2PCI	0x01000000	/* ME PCIm-to-PCI active */
+#define E1000_ICH_FWSM_PCIM2PCI_COUNT	2000
+
+#define E1000_ICH_MNG_IAMT_MODE		0x2
+
+#define E1000_FWSM_WLOCK_MAC_MASK	0x0380
+#define E1000_FWSM_WLOCK_MAC_SHIFT	7
+
+/* Shared Receive Address Registers */
+#define E1000_SHRAL_PCH_LPT(_i)		(0x05408 + ((_i) * 8))
+#define E1000_SHRAH_PCH_LPT(_i)		(0x0540C + ((_i) * 8))
+
+#define ID_LED_DEFAULT_ICH8LAN	((ID_LED_DEF1_DEF2 << 12) | \
+				 (ID_LED_OFF1_OFF2 <<  8) | \
+				 (ID_LED_OFF1_ON2  <<  4) | \
+				 (ID_LED_DEF1_DEF2))
+
+#define E1000_ICH_NVM_SIG_WORD		0x13
+#define E1000_ICH_NVM_SIG_MASK		0xC000
+#define E1000_ICH_NVM_VALID_SIG_MASK	0xC0
+#define E1000_ICH_NVM_SIG_VALUE		0x80
+
+#define E1000_ICH8_LAN_INIT_TIMEOUT	1500
+
+#define E1000_FEXTNVM_SW_CONFIG		1
+#define E1000_FEXTNVM_SW_CONFIG_ICH8M	(1 << 27)	/* different on ICH8M */
+
+#define E1000_FEXTNVM3_PHY_CFG_COUNTER_MASK	0x0C000000
+#define E1000_FEXTNVM3_PHY_CFG_COUNTER_50MSEC	0x08000000
+
+#define E1000_FEXTNVM4_BEACON_DURATION_MASK	0x7
+#define E1000_FEXTNVM4_BEACON_DURATION_8USEC	0x7
+#define E1000_FEXTNVM4_BEACON_DURATION_16USEC	0x3
+
+#define PCIE_ICH8_SNOOP_ALL	PCIE_NO_SNOOP_ALL
+
+#define E1000_ICH_RAR_ENTRIES	7
+#define E1000_PCH2_RAR_ENTRIES	5	/* RAR[0], SHRA[0-3] */
+#define E1000_PCH_LPT_RAR_ENTRIES	12	/* RAR[0], SHRA[0-10] */
+
+#define PHY_PAGE_SHIFT		5
+#define PHY_REG(page, reg)	(((page) << PHY_PAGE_SHIFT) | \
+				 ((reg) & MAX_PHY_REG_ADDRESS))
+#define IGP3_KMRN_DIAG	PHY_REG(770, 19)	/* KMRN Diagnostic */
+#define IGP3_VR_CTRL	PHY_REG(776, 18)	/* Voltage Regulator Control */
+
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS		0x0002
+#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK	0x0300
+#define IGP3_VR_CTRL_MODE_SHUTDOWN		0x0200
+
+/* PHY Wakeup Registers and defines */
+#define BM_PORT_GEN_CFG		PHY_REG(BM_PORT_CTRL_PAGE, 17)
+#define BM_RCTL			PHY_REG(BM_WUC_PAGE, 0)
+#define BM_WUC			PHY_REG(BM_WUC_PAGE, 1)
+#define BM_WUFC			PHY_REG(BM_WUC_PAGE, 2)
+#define BM_WUS			PHY_REG(BM_WUC_PAGE, 3)
+#define BM_RAR_L(_i)		(BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
+#define BM_RAR_M(_i)		(BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
+#define BM_RAR_H(_i)		(BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
+#define BM_RAR_CTRL(_i)		(BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
+#define BM_MTA(_i)		(BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
+
+#define BM_RCTL_UPE		0x0001	/* Unicast Promiscuous Mode */
+#define BM_RCTL_MPE		0x0002	/* Multicast Promiscuous Mode */
+#define BM_RCTL_MO_SHIFT	3	/* Multicast Offset Shift */
+#define BM_RCTL_MO_MASK		(3 << 3)	/* Multicast Offset Mask */
+#define BM_RCTL_BAM		0x0020	/* Broadcast Accept Mode */
+#define BM_RCTL_PMCF		0x0040	/* Pass MAC Control Frames */
+#define BM_RCTL_RFCE		0x0080	/* Rx Flow Control Enable */
+
+#define HV_LED_CONFIG		PHY_REG(768, 30)	/* LED Configuration */
+#define HV_MUX_DATA_CTRL	PHY_REG(776, 16)
+#define HV_MUX_DATA_CTRL_GEN_TO_MAC	0x0400
+#define HV_MUX_DATA_CTRL_FORCE_SPEED	0x0004
+#define HV_STATS_PAGE	778
+/* Half-duplex collision counts */
+#define HV_SCC_UPPER	PHY_REG(HV_STATS_PAGE, 16)	/* Single Collision */
+#define HV_SCC_LOWER	PHY_REG(HV_STATS_PAGE, 17)
+#define HV_ECOL_UPPER	PHY_REG(HV_STATS_PAGE, 18)	/* Excessive Coll. */
+#define HV_ECOL_LOWER	PHY_REG(HV_STATS_PAGE, 19)
+#define HV_MCC_UPPER	PHY_REG(HV_STATS_PAGE, 20)	/* Multiple Collision */
+#define HV_MCC_LOWER	PHY_REG(HV_STATS_PAGE, 21)
+#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23)	/* Late Collision */
+#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
+#define HV_COLC_UPPER	PHY_REG(HV_STATS_PAGE, 25)	/* Collision */
+#define HV_COLC_LOWER	PHY_REG(HV_STATS_PAGE, 26)
+#define HV_DC_UPPER	PHY_REG(HV_STATS_PAGE, 27)	/* Defer Count */
+#define HV_DC_LOWER	PHY_REG(HV_STATS_PAGE, 28)
+#define HV_TNCRS_UPPER	PHY_REG(HV_STATS_PAGE, 29)	/* Tx with no CRS */
+#define HV_TNCRS_LOWER	PHY_REG(HV_STATS_PAGE, 30)
+
+#define E1000_FCRTV_PCH	0x05F40	/* PCH Flow Control Refresh Timer Value */
+
+#define E1000_NVM_K1_CONFIG	0x1B	/* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE	0x1	/* NVM Enable K1 bit */
+
+/* SMBus Control Phy Register */
+#define CV_SMB_CTRL		PHY_REG(769, 23)
+#define CV_SMB_CTRL_FORCE_SMBUS	0x0001
+
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR		PHY_REG(768, 26)
+#define HV_SMB_ADDR_MASK	0x007F
+#define HV_SMB_ADDR_PEC_EN	0x0200
+#define HV_SMB_ADDR_VALID	0x0080
+#define HV_SMB_ADDR_FREQ_MASK		0x1100
+#define HV_SMB_ADDR_FREQ_LOW_SHIFT	8
+#define HV_SMB_ADDR_FREQ_HIGH_SHIFT	12
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP			0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK	0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT	17
+#define E1000_STRAP_SMT_FREQ_MASK	0x00003000
+#define E1000_STRAP_SMT_FREQ_SHIFT	12
+
+/* OEM Bits Phy Register */
+#define HV_OEM_BITS		PHY_REG(768, 25)
+#define HV_OEM_BITS_LPLU	0x0004	/* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS	0x0040	/* Gigabit Disable */
+#define HV_OEM_BITS_RESTART_AN	0x0400	/* Restart Auto-negotiation */
+
+/* KMRN Mode Control */
+#define HV_KMRN_MODE_CTRL	PHY_REG(769, 16)
+#define HV_KMRN_MDIO_SLOW	0x0400
+
+/* KMRN FIFO Control and Status */
+#define HV_KMRN_FIFO_CTRLSTA			PHY_REG(770, 16)
+#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_MASK	0x7000
+#define HV_KMRN_FIFO_CTRLSTA_PREAMBLE_SHIFT	12
+
+/* PHY Power Management Control */
+#define HV_PM_CTRL		PHY_REG(770, 17)
+#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
+
+#define SW_FLAG_TIMEOUT		1000	/* SW Semaphore flag timeout in ms */
+
+/* PHY Low Power Idle Control */
+#define I82579_LPI_CTRL				PHY_REG(772, 20)
+#define I82579_LPI_CTRL_100_ENABLE		0x2000
+#define I82579_LPI_CTRL_1000_ENABLE		0x4000
+#define I82579_LPI_CTRL_ENABLE_MASK		0x6000
+#define I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT	0x80
+
+/* Extended Management Interface (EMI) Registers */
+#define I82579_EMI_ADDR		0x10
+#define I82579_EMI_DATA		0x11
+#define I82579_LPI_UPDATE_TIMER	0x4805	/* in 40ns units + 40 ns base value */
+#define I82579_MSE_THRESHOLD	0x084F	/* 82579 Mean Square Error Threshold */
+#define I82577_MSE_THRESHOLD	0x0887	/* 82577 Mean Square Error Threshold */
+#define I82579_MSE_LINK_DOWN	0x2411	/* MSE count before dropping link */
+#define I82579_EEE_PCS_STATUS		0x182D	/* IEEE MMD Register 3.1 >> 8 */
+#define I82579_EEE_CAPABILITY		0x0410	/* IEEE MMD Register 3.20 */
+#define I82579_EEE_ADVERTISEMENT	0x040E	/* IEEE MMD Register 7.60 */
+#define I82579_EEE_LP_ABILITY		0x040F	/* IEEE MMD Register 7.61 */
+#define I82579_EEE_100_SUPPORTED	(1 << 1)	/* 100BaseTx EEE */
+#define I82579_EEE_1000_SUPPORTED	(1 << 2)	/* 1000BaseTx EEE */
+#define I217_EEE_PCS_STATUS	0x9401	/* IEEE MMD Register 3.1 */
+#define I217_EEE_CAPABILITY	0x8000	/* IEEE MMD Register 3.20 */
+#define I217_EEE_ADVERTISEMENT	0x8001	/* IEEE MMD Register 7.60 */
+#define I217_EEE_LP_ABILITY	0x8002	/* IEEE MMD Register 7.61 */
+
+#define E1000_EEE_RX_LPI_RCVD	0x0400	/* Tx LP idle received */
+#define E1000_EEE_TX_LPI_RCVD	0x0800	/* Rx LP idle received */
+
+/* Intel Rapid Start Technology Support */
+#define I217_PROXY_CTRL		BM_PHY_REG(BM_WUC_PAGE, 70)
+#define I217_PROXY_CTRL_AUTO_DISABLE	0x0080
+#define I217_SxCTRL			PHY_REG(BM_PORT_CTRL_PAGE, 28)
+#define I217_SxCTRL_ENABLE_LPI_RESET	0x1000
+#define I217_CGFREG			PHY_REG(772, 29)
+#define I217_CGFREG_ENABLE_MTA_RESET	0x0002
+#define I217_MEMPWR			PHY_REG(772, 26)
+#define I217_MEMPWR_DISABLE_SMB_RELEASE	0x0010
+
+/* Receive Address Initial CRC Calculation */
+#define E1000_PCH_RAICC(_n)	(0x05F50 + ((_n) * 4))
+
+/* Latency Tolerance Reporting */
+#define E1000_LTRV			0x000F8
+#define E1000_LTRV_SCALE_MAX		5
+#define E1000_LTRV_SCALE_FACTOR		5
+#define E1000_LTRV_REQ_SHIFT		15
+#define E1000_LTRV_NOSNOOP_SHIFT	16
+#define E1000_LTRV_SEND			(1 << 30)
+
+/* Proprietary Latency Tolerance Reporting PCI Capability */
+#define E1000_PCI_LTR_CAP_LPT		0xA8
+
+/* OBFF Control & Threshold Defines */
+#define E1000_SVCR_OFF_EN		0x00000001
+#define E1000_SVCR_OFF_MASKINT		0x00001000
+#define E1000_SVCR_OFF_TIMER_MASK	0xFFFF0000
+#define E1000_SVCR_OFF_TIMER_SHIFT	16
+#define E1000_SVT_OFF_HWM_MASK		0x0000001F
+
+void e1000e_write_protect_nvm_ich8lan(struct e1000_hw *hw);
+void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
+						  bool state);
+void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
+void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
+void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
+void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
+s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
+void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
+s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
+s32 e1000_read_emi_reg_locked(struct e1000_hw *hw, u16 addr, u16 *data);
+#endif /* _E1000E_ICH8LAN_H_ */
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index ae656f16c9fd..851685dd00d4 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -91,10 +91,6 @@ static const u16 e1000_igp_2_cable_length_table[] = {
 /* BM PHY Copper Specific Control 1 */
 #define BM_CS_CTRL1                       16
 
-#define HV_MUX_DATA_CTRL               PHY_REG(776, 16)
-#define HV_MUX_DATA_CTRL_GEN_TO_MAC    0x0400
-#define HV_MUX_DATA_CTRL_FORCE_SPEED   0x0004
-
 /**
  *  e1000e_check_reset_block_generic - Check if PHY reset is blocked
  *  @hw: pointer to the HW structure
-- 
cgit v1.2.3