From a925a3763982799460b9e9b5299520172652b785 Mon Sep 17 00:00:00 2001
From: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Date: Fri, 28 Aug 2015 17:21:34 +0530
Subject: ath10k: fix DMA alloc failure for target requested memory chunks

During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.

To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.

Failure happens with the following stack trace

[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 +
 1 file changed, 1 insertion(+)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b87b98617073..6e5aeed5faee 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -1714,6 +1714,7 @@ void ath10k_core_destroy(struct ath10k *ar)
 	destroy_workqueue(ar->workqueue_aux);
 
 	ath10k_debug_destroy(ar);
+	ath10k_wmi_free_host_mem(ar);
 	ath10k_mac_destroy(ar);
 }
 EXPORT_SYMBOL(ath10k_core_destroy);
-- 
cgit v1.2.3


From 7b7da0a02192fd518c26c46dad6b14aca4569605 Mon Sep 17 00:00:00 2001
From: Vivek Natarajan <nataraja@qti.qualcomm.com>
Date: Mon, 31 Aug 2015 16:34:55 +0530
Subject: ath10k: drop probe responses when too many are queued

In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.

Fix this by limiting the probe responses when the specified
threshold limit is reached.

Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c   |  5 +++
 drivers/net/wireless/ath/ath10k/core.h   |  5 +++
 drivers/net/wireless/ath/ath10k/htt.h    |  3 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 52 +++++++++++++++++++++++++++-----
 drivers/net/wireless/ath/ath10k/txrx.c   | 14 +++++++--
 5 files changed, 68 insertions(+), 11 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 6e5aeed5faee..6e5033bac2b4 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -54,6 +54,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.has_shifted_cc_wraparound = true,
 		.otp_exe_param = 0,
 		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
 		.fw = {
 			.dir = QCA988X_HW_2_0_FW_DIR,
 			.fw = QCA988X_HW_2_0_FW_FILE,
@@ -70,6 +71,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.uart_pin = 6,
 		.otp_exe_param = 0,
 		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
 		.fw = {
 			.dir = QCA6174_HW_2_1_FW_DIR,
 			.fw = QCA6174_HW_2_1_FW_FILE,
@@ -86,6 +88,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.uart_pin = 6,
 		.otp_exe_param = 0,
 		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
 		.fw = {
 			.dir = QCA6174_HW_3_0_FW_DIR,
 			.fw = QCA6174_HW_3_0_FW_FILE,
@@ -102,6 +105,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.uart_pin = 6,
 		.otp_exe_param = 0,
 		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
 		.fw = {
 			/* uses same binaries as hw3.0 */
 			.dir = QCA6174_HW_3_0_FW_DIR,
@@ -120,6 +124,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.otp_exe_param = 0x00000700,
 		.continuous_frag_desc = true,
 		.channel_counters_freq_hz = 150000,
+		.max_probe_resp_desc_thres = 24,
 		.fw = {
 			.dir = QCA99X0_HW_2_0_FW_DIR,
 			.fw = QCA99X0_HW_2_0_FW_FILE,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 12542144fe12..04e040a06cb1 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -612,6 +612,11 @@ struct ath10k {
 
 		u32 channel_counters_freq_hz;
 
+		/* Mgmt tx descriptors threshold for limiting probe response
+		 * frames.
+		 */
+		u32 max_probe_resp_desc_thres;
+
 		struct ath10k_hw_params_fw {
 			const char *dir;
 			const char *fw;
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 573187512895..5a8e4eae7a9c 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1485,6 +1485,7 @@ struct ath10k_htt {
 	spinlock_t tx_lock;
 	int max_num_pending_tx;
 	int num_pending_tx;
+	int num_pending_mgmt_tx;
 	struct idr pending_tx;
 	wait_queue_head_t empty_tx_wq;
 	struct dma_pool *tx_pool;
@@ -1587,7 +1588,7 @@ int ath10k_htt_h2t_aggr_cfg_msg(struct ath10k_htt *htt,
 				u8 max_subfrms_ampdu,
 				u8 max_subfrms_amsdu);
 
-void __ath10k_htt_tx_dec_pending(struct ath10k_htt *htt);
+void __ath10k_htt_tx_dec_pending(struct ath10k_htt *htt, bool limit_mgmt_desc);
 int ath10k_htt_tx_alloc_msdu_id(struct ath10k_htt *htt, struct sk_buff *skb);
 void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id);
 int ath10k_htt_mgmt_tx(struct ath10k_htt *htt, struct sk_buff *);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 43aa5e2d1b87..ea53c2151122 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -22,22 +22,28 @@
 #include "txrx.h"
 #include "debug.h"
 
-void __ath10k_htt_tx_dec_pending(struct ath10k_htt *htt)
+void __ath10k_htt_tx_dec_pending(struct ath10k_htt *htt, bool limit_mgmt_desc)
 {
+	if (limit_mgmt_desc)
+		htt->num_pending_mgmt_tx--;
+
 	htt->num_pending_tx--;
 	if (htt->num_pending_tx == htt->max_num_pending_tx - 1)
 		ath10k_mac_tx_unlock(htt->ar, ATH10K_TX_PAUSE_Q_FULL);
 }
 
-static void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt)
+static void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt,
+				      bool limit_mgmt_desc)
 {
 	spin_lock_bh(&htt->tx_lock);
-	__ath10k_htt_tx_dec_pending(htt);
+	__ath10k_htt_tx_dec_pending(htt, limit_mgmt_desc);
 	spin_unlock_bh(&htt->tx_lock);
 }
 
-static int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt)
+static int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt,
+				     bool limit_mgmt_desc, bool is_probe_resp)
 {
+	struct ath10k *ar = htt->ar;
 	int ret = 0;
 
 	spin_lock_bh(&htt->tx_lock);
@@ -47,6 +53,15 @@ static int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt)
 		goto exit;
 	}
 
+	if (limit_mgmt_desc) {
+		if (is_probe_resp && (htt->num_pending_mgmt_tx >
+		    ar->hw_params.max_probe_resp_desc_thres)) {
+			ret = -EBUSY;
+			goto exit;
+		}
+		htt->num_pending_mgmt_tx++;
+	}
+
 	htt->num_pending_tx++;
 	if (htt->num_pending_tx == htt->max_num_pending_tx)
 		ath10k_mac_tx_lock(htt->ar, ATH10K_TX_PAUSE_Q_FULL);
@@ -417,8 +432,19 @@ int ath10k_htt_mgmt_tx(struct ath10k_htt *htt, struct sk_buff *msdu)
 	int len = 0;
 	int msdu_id = -1;
 	int res;
+	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)msdu->data;
+	bool limit_mgmt_desc = false;
+	bool is_probe_resp = false;
+
+	if (ar->hw_params.max_probe_resp_desc_thres) {
+		limit_mgmt_desc = true;
+
+		if (ieee80211_is_probe_resp(hdr->frame_control))
+			is_probe_resp = true;
+	}
+
+	res = ath10k_htt_tx_inc_pending(htt, limit_mgmt_desc, is_probe_resp);
 
-	res = ath10k_htt_tx_inc_pending(htt);
 	if (res)
 		goto err;
 
@@ -476,7 +502,7 @@ err_free_msdu_id:
 	ath10k_htt_tx_free_msdu_id(htt, msdu_id);
 	spin_unlock_bh(&htt->tx_lock);
 err_tx_dec:
-	ath10k_htt_tx_dec_pending(htt);
+	ath10k_htt_tx_dec_pending(htt, limit_mgmt_desc);
 err:
 	return res;
 }
@@ -498,8 +524,18 @@ int ath10k_htt_tx(struct ath10k_htt *htt, struct sk_buff *msdu)
 	dma_addr_t paddr = 0;
 	u32 frags_paddr = 0;
 	struct htt_msdu_ext_desc *ext_desc = NULL;
+	bool limit_mgmt_desc = false;
+	bool is_probe_resp = false;
+
+	if (unlikely(ieee80211_is_mgmt(hdr->frame_control)) &&
+	    ar->hw_params.max_probe_resp_desc_thres) {
+		limit_mgmt_desc = true;
+
+		if (ieee80211_is_probe_resp(hdr->frame_control))
+			is_probe_resp = true;
+	}
 
-	res = ath10k_htt_tx_inc_pending(htt);
+	res = ath10k_htt_tx_inc_pending(htt, limit_mgmt_desc, is_probe_resp);
 	if (res)
 		goto err;
 
@@ -678,7 +714,7 @@ err_free_msdu_id:
 	ath10k_htt_tx_free_msdu_id(htt, msdu_id);
 	spin_unlock_bh(&htt->tx_lock);
 err_tx_dec:
-	ath10k_htt_tx_dec_pending(htt);
+	ath10k_htt_tx_dec_pending(htt, limit_mgmt_desc);
 err:
 	return res;
 }
diff --git a/drivers/net/wireless/ath/ath10k/txrx.c b/drivers/net/wireless/ath/ath10k/txrx.c
index e4a9c4c8d0cb..7db7d501726b 100644
--- a/drivers/net/wireless/ath/ath10k/txrx.c
+++ b/drivers/net/wireless/ath/ath10k/txrx.c
@@ -52,6 +52,9 @@ void ath10k_txrx_tx_unref(struct ath10k_htt *htt,
 	struct ieee80211_tx_info *info;
 	struct ath10k_skb_cb *skb_cb;
 	struct sk_buff *msdu;
+	struct ieee80211_hdr *hdr;
+	__le16 fc;
+	bool limit_mgmt_desc = false;
 
 	ath10k_dbg(ar, ATH10K_DBG_HTT,
 		   "htt tx completion msdu_id %u discard %d no_ack %d success %d\n",
@@ -72,14 +75,21 @@ void ath10k_txrx_tx_unref(struct ath10k_htt *htt,
 		spin_unlock_bh(&htt->tx_lock);
 		return;
 	}
+
+	hdr = (struct ieee80211_hdr *)msdu->data;
+	fc = hdr->frame_control;
+
+	if (unlikely(ieee80211_is_mgmt(fc)) &&
+	    ar->hw_params.max_probe_resp_desc_thres)
+		limit_mgmt_desc = true;
+
 	ath10k_htt_tx_free_msdu_id(htt, tx_done->msdu_id);
-	__ath10k_htt_tx_dec_pending(htt);
+	__ath10k_htt_tx_dec_pending(htt, limit_mgmt_desc);
 	if (htt->num_pending_tx == 0)
 		wake_up(&htt->empty_tx_wq);
 	spin_unlock_bh(&htt->tx_lock);
 
 	skb_cb = ATH10K_SKB_CB(msdu);
-
 	dma_unmap_single(dev, skb_cb->paddr, msdu->len, DMA_TO_DEVICE);
 
 	if (skb_cb->htt.txbuf)
-- 
cgit v1.2.3


From b6c7bafa7d4b1398cce93e4af0a48603919fa933 Mon Sep 17 00:00:00 2001
From: Bob Copeland <me@bobcopeland.com>
Date: Wed, 9 Sep 2015 12:47:36 -0400
Subject: ath10k: implement mesh support

Add support for mesh to ath10k.  We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.

Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode.  As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true.  The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.

When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:

    ip link set wlan0 down
    iw dev wlan0 set type mp
    ip link set wlan0 up
    iw dev wlan0 set freq 5745 80 5775
    iw dev wlan0 mesh join mesh-vht

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 12 ++++++++++++
 drivers/net/wireless/ath/ath10k/mac.c  | 36 +++++++++++++++++++++++++++++++++-
 2 files changed, 47 insertions(+), 1 deletion(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 6e5033bac2b4..09a74a8e082e 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -34,16 +34,19 @@ unsigned int ath10k_debug_mask;
 static unsigned int ath10k_cryptmode_param;
 static bool uart_print;
 static bool skip_otp;
+static bool rawmode;
 
 module_param_named(debug_mask, ath10k_debug_mask, uint, 0644);
 module_param_named(cryptmode, ath10k_cryptmode_param, uint, 0644);
 module_param(uart_print, bool, 0644);
 module_param(skip_otp, bool, 0644);
+module_param(rawmode, bool, 0644);
 
 MODULE_PARM_DESC(debug_mask, "Debugging mask");
 MODULE_PARM_DESC(uart_print, "Uart target debugging");
 MODULE_PARM_DESC(skip_otp, "Skip otp failure for calibration in testmode");
 MODULE_PARM_DESC(cryptmode, "Crypto mode: 0-hardware, 1-software");
+MODULE_PARM_DESC(rawmode, "Use raw 802.11 frame datapath");
 
 static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	{
@@ -1122,6 +1125,15 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
 	ar->htt.max_num_amsdu = ATH10K_HTT_MAX_NUM_AMSDU_DEFAULT;
 	ar->htt.max_num_ampdu = ATH10K_HTT_MAX_NUM_AMPDU_DEFAULT;
 
+	if (rawmode) {
+		if (!test_bit(ATH10K_FW_FEATURE_RAW_MODE_SUPPORT,
+			      ar->fw_features)) {
+			ath10k_err(ar, "rawmode = 1 requires support from firmware");
+			return -EINVAL;
+		}
+		set_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags);
+	}
+
 	if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
 		ar->wmi.rx_decap_mode = ATH10K_HW_TXRX_RAW;
 
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 80efcc8debfe..1cda4f9dd453 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4211,6 +4211,14 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	case NL80211_IFTYPE_ADHOC:
 		arvif->vdev_type = WMI_VDEV_TYPE_IBSS;
 		break;
+	case NL80211_IFTYPE_MESH_POINT:
+		if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) {
+			ret = -EINVAL;
+			ath10k_warn(ar, "must load driver with rawmode=1 to add mesh interfaces\n");
+			goto err;
+		}
+		arvif->vdev_type = WMI_VDEV_TYPE_AP;
+		break;
 	case NL80211_IFTYPE_AP:
 		arvif->vdev_type = WMI_VDEV_TYPE_AP;
 
@@ -4251,6 +4259,7 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	 * become corrupted, e.g. have garbled IEs or out-of-date TIM bitmap.
 	 */
 	if (vif->type == NL80211_IFTYPE_ADHOC ||
+	    vif->type == NL80211_IFTYPE_MESH_POINT ||
 	    vif->type == NL80211_IFTYPE_AP) {
 		arvif->beacon_buf = dma_zalloc_coherent(ar->dev,
 							IEEE80211_MAX_FRAME_LEN,
@@ -4590,6 +4599,13 @@ static void ath10k_bss_info_changed(struct ieee80211_hw *hw,
 		if (ret)
 			ath10k_warn(ar, "failed to update beacon template: %d\n",
 				    ret);
+
+		if (ieee80211_vif_is_mesh(vif)) {
+			/* mesh doesn't use SSID but firmware needs it */
+			strncpy(arvif->u.ap.ssid, "mesh",
+				sizeof(arvif->u.ap.ssid));
+			arvif->u.ap.ssid_len = 4;
+		}
 	}
 
 	if (changed & BSS_CHANGED_AP_PROBE_RESP) {
@@ -5329,6 +5345,7 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 	} else if (old_state == IEEE80211_STA_AUTH &&
 		   new_state == IEEE80211_STA_ASSOC &&
 		   (vif->type == NL80211_IFTYPE_AP ||
+		    vif->type == NL80211_IFTYPE_MESH_POINT ||
 		    vif->type == NL80211_IFTYPE_ADHOC)) {
 		/*
 		 * New association.
@@ -5364,6 +5381,7 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 	} else if (old_state == IEEE80211_STA_ASSOC &&
 		    new_state == IEEE80211_STA_AUTH &&
 		    (vif->type == NL80211_IFTYPE_AP ||
+		     vif->type == NL80211_IFTYPE_MESH_POINT ||
 		     vif->type == NL80211_IFTYPE_ADHOC)) {
 		/*
 		 * Disassociation.
@@ -6678,6 +6696,9 @@ static const struct ieee80211_iface_limit ath10k_if_limits[] = {
 	{
 	.max	= 7,
 	.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+		| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -6685,6 +6706,9 @@ static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = {
 	{
 	.max	= 8,
 	.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+		| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -6722,6 +6746,9 @@ static const struct ieee80211_iface_limit ath10k_tlv_if_limit[] = {
 	{
 		.max = 2,
 		.types = BIT(NL80211_IFTYPE_AP) |
+#ifdef CONFIG_MAC80211_MESH
+			 BIT(NL80211_IFTYPE_MESH_POINT) |
+#endif
 			 BIT(NL80211_IFTYPE_P2P_CLIENT) |
 			 BIT(NL80211_IFTYPE_P2P_GO),
 	},
@@ -6743,6 +6770,9 @@ static const struct ieee80211_iface_limit ath10k_tlv_qcs_if_limit[] = {
 	{
 		.max = 1,
 		.types = BIT(NL80211_IFTYPE_AP) |
+#ifdef CONFIG_MAC80211_MESH
+			 BIT(NL80211_IFTYPE_MESH_POINT) |
+#endif
 			 BIT(NL80211_IFTYPE_P2P_GO),
 	},
 	{
@@ -6809,6 +6839,9 @@ static const struct ieee80211_iface_limit ath10k_10_4_if_limits[] = {
 	{
 		.max	= 16,
 		.types	= BIT(NL80211_IFTYPE_AP)
+#ifdef CONFIG_MAC80211_MESH
+			| BIT(NL80211_IFTYPE_MESH_POINT)
+#endif
 	},
 };
 
@@ -7033,7 +7066,8 @@ int ath10k_mac_register(struct ath10k *ar)
 
 	ar->hw->wiphy->interface_modes =
 		BIT(NL80211_IFTYPE_STATION) |
-		BIT(NL80211_IFTYPE_AP);
+		BIT(NL80211_IFTYPE_AP) |
+		BIT(NL80211_IFTYPE_MESH_POINT);
 
 	ar->hw->wiphy->available_antennas_rx = ar->supp_rx_chainmask;
 	ar->hw->wiphy->available_antennas_tx = ar->supp_tx_chainmask;
-- 
cgit v1.2.3


From 5af82fa66a7ee8dfc29fadb487a02e2ef14ea965 Mon Sep 17 00:00:00 2001
From: Kalle Valo <kvalo@qca.qualcomm.com>
Date: Wed, 9 Sep 2015 11:34:37 +0300
Subject: ath10k: add ATH10K_FW_FEATURE_RAW_MODE_SUPPORT to
 ath10k_core_fw_feature_str[]

This was missed in the original commit adding the flag and ath10k only printed "bit10":

ath10k_pci 0000:02:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70.6-2 api 3
htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,bit10

Also add a build test to avoid this happening again.

Fixes: ccec9038c721 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 5 +++++
 1 file changed, 5 insertions(+)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 09a74a8e082e..879625adc63a 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -150,12 +150,17 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_IGNORE_OTP_RESULT] = "ignore-otp",
 	[ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING] = "no-4addr-pad",
 	[ATH10K_FW_FEATURE_SUPPORTS_SKIP_CLOCK_INIT] = "skip-clock-init",
+	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
 						   size_t buf_len,
 						   enum ath10k_fw_features feat)
 {
+	/* make sure that ath10k_core_fw_feature_str[] gets updated */
+	BUILD_BUG_ON(ARRAY_SIZE(ath10k_core_fw_feature_str) !=
+		     ATH10K_FW_FEATURE_COUNT);
+
 	if (feat >= ARRAY_SIZE(ath10k_core_fw_feature_str) ||
 	    WARN_ON(!ath10k_core_fw_feature_str[feat])) {
 		return scnprintf(buf, buf_len, "bit%d", feat);
-- 
cgit v1.2.3


From be62e92a5b2b5960b494fc81ce27611240016821 Mon Sep 17 00:00:00 2001
From: Kalle Valo <kvalo@qca.qualcomm.com>
Date: Mon, 5 Oct 2015 17:56:34 +0300
Subject: ath10k: fix checkpatch warning about logical continuations

checkpatch found:

drivers/net/wireless/ath/ath9k/core.c:490: Logical continuations should be on the previous line

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 879625adc63a..87ad2e998a94 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -486,8 +486,8 @@ static int ath10k_download_and_run_otp(struct ath10k *ar)
 	ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot otp execute result %d\n", result);
 
 	if (!(skip_otp || test_bit(ATH10K_FW_FEATURE_IGNORE_OTP_RESULT,
-				   ar->fw_features))
-	    && result != 0) {
+				   ar->fw_features)) &&
+	    result != 0) {
 		ath10k_err(ar, "otp calibration failed: %d", result);
 		return -EINVAL;
 	}
-- 
cgit v1.2.3


From 617b0f4d4a69962e0e86604f889d6af9e8f4150d Mon Sep 17 00:00:00 2001
From: Kalle Valo <kvalo@qca.qualcomm.com>
Date: Mon, 5 Oct 2015 17:56:35 +0300
Subject: ath10k: indentation fixes

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 10 +++++-----
 drivers/net/wireless/ath/ath10k/mac.c  |  6 +++---
 drivers/net/wireless/ath/ath10k/pci.c  |  2 +-
 drivers/net/wireless/ath/ath10k/wmi.c  |  2 +-
 4 files changed, 10 insertions(+), 10 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 87ad2e998a94..12fef599debe 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -510,7 +510,7 @@ static int ath10k_download_fw(struct ath10k *ar, enum ath10k_firmware_mode mode)
 		data_len = ar->firmware_len;
 		mode_name = "normal";
 		ret = ath10k_swap_code_seg_configure(ar,
-				ATH10K_SWAP_CODE_SEG_BIN_TYPE_FW);
+						     ATH10K_SWAP_CODE_SEG_BIN_TYPE_FW);
 		if (ret) {
 			ath10k_err(ar, "failed to configure fw code swap: %d\n",
 				   ret);
@@ -1263,10 +1263,10 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode)
 		goto err;
 
 	/* Some of of qca988x solutions are having global reset issue
-         * during target initialization. Bypassing PLL setting before
-         * downloading firmware and letting the SoC run on REF_CLK is
-         * fixing the problem. Corresponding firmware change is also needed
-         * to set the clock source once the target is initialized.
+	 * during target initialization. Bypassing PLL setting before
+	 * downloading firmware and letting the SoC run on REF_CLK is
+	 * fixing the problem. Corresponding firmware change is also needed
+	 * to set the clock source once the target is initialized.
 	 */
 	if (test_bit(ATH10K_FW_FEATURE_SUPPORTS_SKIP_CLOCK_INIT,
 		     ar->fw_features)) {
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 3f6c1c42a70f..3106e3bfa515 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4656,7 +4656,7 @@ static void ath10k_bss_info_changed(struct ieee80211_hw *hw,
 						info->use_cts_prot ? 1 : 0);
 		if (ret)
 			ath10k_warn(ar, "failed to set protection mode %d on vdev %i: %d\n",
-					info->use_cts_prot, arvif->vdev_id, ret);
+				    info->use_cts_prot, arvif->vdev_id, ret);
 	}
 
 	if (changed & BSS_CHANGED_ERP_SLOT) {
@@ -6268,8 +6268,8 @@ ath10k_mac_update_rx_channel(struct ath10k *ar,
 	rcu_read_lock();
 	if (!ctx && ath10k_mac_num_chanctxs(ar) == 1) {
 		ieee80211_iter_chan_contexts_atomic(ar->hw,
-					ath10k_mac_get_any_chandef_iter,
-					&def);
+						    ath10k_mac_get_any_chandef_iter,
+						    &def);
 
 		if (vifs)
 			def = &vifs[0].new_ctx->def;
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 110fcad609b9..08cc4304001e 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -2257,7 +2257,7 @@ static int ath10k_pci_qca6174_chip_reset(struct ath10k *ar)
 	ret = ath10k_pci_wait_for_target_init(ar);
 	if (ret) {
 		ath10k_warn(ar, "failed to wait for target after cold reset: %d\n",
-				ret);
+			    ret);
 		return ret;
 	}
 
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 87d9de2aa8c5..0c7a233a223c 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -3507,7 +3507,7 @@ void ath10k_wmi_event_spectral_scan(struct ath10k *ar,
 							  tsf);
 			if (res < 0) {
 				ath10k_dbg(ar, ATH10K_DBG_WMI, "failed to process fft report: %d\n",
-					    res);
+					   res);
 				return;
 			}
 			break;
-- 
cgit v1.2.3


From 9a14969fa1674d2215d6d9f171ed323bd3ebb39d Mon Sep 17 00:00:00 2001
From: Kalle Valo <kvalo@qca.qualcomm.com>
Date: Mon, 5 Oct 2015 17:56:36 +0300
Subject: ath10k: fix whitespace usage

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 -
 drivers/net/wireless/ath/ath10k/mac.c  | 4 +++-
 drivers/net/wireless/ath/ath10k/pci.c  | 1 +
 3 files changed, 4 insertions(+), 2 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 12fef599debe..c295c919568b 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -570,7 +570,6 @@ static void ath10k_core_free_firmware_files(struct ath10k *ar)
 	ar->firmware_len = 0;
 
 	ar->cal_file = NULL;
-
 }
 
 static int ath10k_fetch_cal_file(struct ath10k *ar)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index cde0af81b6e7..185651db71c0 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4064,6 +4064,7 @@ static u32 get_nss_from_chainmask(u16 chain_mask)
 static int ath10k_mac_get_vht_cap_bf_sts(struct ath10k *ar)
 {
 	int nsts = ar->vht_cap_info;
+
 	nsts &= IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK;
 	nsts >>= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT;
 
@@ -4080,8 +4081,9 @@ static int ath10k_mac_get_vht_cap_bf_sts(struct ath10k *ar)
 static int ath10k_mac_get_vht_cap_bf_sound_dim(struct ath10k *ar)
 {
 	int sound_dim = ar->vht_cap_info;
+
 	sound_dim &= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK;
-	sound_dim >>=IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT;
+	sound_dim >>= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT;
 
 	/* If the sounding dimension is not advertised by the firmware,
 	 * let's use a default value of 1
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 08cc4304001e..61df93e2e1c9 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -1504,6 +1504,7 @@ static void ath10k_pci_irq_enable(struct ath10k *ar)
 static int ath10k_pci_hif_start(struct ath10k *ar)
 {
 	struct ath10k_pci *ar_pci = ath10k_pci_priv(ar);
+
 	ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot hif start\n");
 
 	ath10k_pci_irq_enable(ar);
-- 
cgit v1.2.3


From 0a51b343abfe2c0dbcbd9ec3c4b18bb8779fefa8 Mon Sep 17 00:00:00 2001
From: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Date: Fri, 9 Oct 2015 11:55:58 +0300
Subject: ath10k: add board 2 API support

QCA6174 needs different board files based on board type. To make it easier to
distribute multiple board files and automatically choose correct board file
create a simple TLV file format following the same principles as with FW IEs.
The file is named board-2.bin and contain multiple board files. Each board file
then can have multiple names.

ath10k searches for file board-N.bin (where N is the interface version number
for the board file, just like we for firmware files) in /lib/firmware/*, for
example for qca99x0 it will try to find it here:

/lib/firmware/ath10k/QCA99X0/hw2.0/board-2.bin

If ath10k doesn't find board-2.bin then it will fallback to the old board.bin file.

This patch adds a simple name scheme using pci device id which for now will be
used by qca6174:

bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x

This removes the old method of having subsystem ids in ar->spec_board_id and
using that in the board file name.

Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: simplified the file format, rewrote commit log, other smaller changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c  | 249 +++++++++++++++++++++++++++-----
 drivers/net/wireless/ath/ath10k/core.h  |   9 +-
 drivers/net/wireless/ath/ath10k/debug.c |  12 +-
 drivers/net/wireless/ath/ath10k/hw.h    |  13 ++
 drivers/net/wireless/ath/ath10k/pci.c   |  16 +-
 5 files changed, 250 insertions(+), 49 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index c295c919568b..99a4e145c9b6 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -541,11 +541,18 @@ static int ath10k_download_fw(struct ath10k *ar, enum ath10k_firmware_mode mode)
 	return ret;
 }
 
-static void ath10k_core_free_firmware_files(struct ath10k *ar)
+static void ath10k_core_free_board_files(struct ath10k *ar)
 {
 	if (!IS_ERR(ar->board))
 		release_firmware(ar->board);
 
+	ar->board = NULL;
+	ar->board_data = NULL;
+	ar->board_len = 0;
+}
+
+static void ath10k_core_free_firmware_files(struct ath10k *ar)
+{
 	if (!IS_ERR(ar->otp))
 		release_firmware(ar->otp);
 
@@ -557,10 +564,6 @@ static void ath10k_core_free_firmware_files(struct ath10k *ar)
 
 	ath10k_swap_code_seg_release(ar);
 
-	ar->board = NULL;
-	ar->board_data = NULL;
-	ar->board_len = 0;
-
 	ar->otp = NULL;
 	ar->otp_data = NULL;
 	ar->otp_len = 0;
@@ -591,68 +594,241 @@ static int ath10k_fetch_cal_file(struct ath10k *ar)
 	return 0;
 }
 
-static int ath10k_core_fetch_spec_board_file(struct ath10k *ar)
+static int ath10k_core_fetch_board_data_api_1(struct ath10k *ar)
 {
-	char filename[100];
-
-	scnprintf(filename, sizeof(filename), "board-%s-%s.bin",
-		  ath10k_bus_str(ar->hif.bus), ar->spec_board_id);
+	if (!ar->hw_params.fw.board) {
+		ath10k_err(ar, "failed to find board file fw entry\n");
+		return -EINVAL;
+	}
 
-	ar->board = ath10k_fetch_fw_file(ar, ar->hw_params.fw.dir, filename);
+	ar->board = ath10k_fetch_fw_file(ar,
+					 ar->hw_params.fw.dir,
+					 ar->hw_params.fw.board);
 	if (IS_ERR(ar->board))
 		return PTR_ERR(ar->board);
 
 	ar->board_data = ar->board->data;
 	ar->board_len = ar->board->size;
-	ar->spec_board_loaded = true;
 
 	return 0;
 }
 
-static int ath10k_core_fetch_generic_board_file(struct ath10k *ar)
+static int ath10k_core_parse_bd_ie_board(struct ath10k *ar,
+					 const void *buf, size_t buf_len,
+					 const char *boardname)
 {
-	if (!ar->hw_params.fw.board) {
-		ath10k_err(ar, "failed to find board file fw entry\n");
-		return -EINVAL;
+	const struct ath10k_fw_ie *hdr;
+	bool name_match_found;
+	int ret, board_ie_id;
+	size_t board_ie_len;
+	const void *board_ie_data;
+
+	name_match_found = false;
+
+	/* go through ATH10K_BD_IE_BOARD_ elements */
+	while (buf_len > sizeof(struct ath10k_fw_ie)) {
+		hdr = buf;
+		board_ie_id = le32_to_cpu(hdr->id);
+		board_ie_len = le32_to_cpu(hdr->len);
+		board_ie_data = hdr->data;
+
+		buf_len -= sizeof(*hdr);
+		buf += sizeof(*hdr);
+
+		if (buf_len < ALIGN(board_ie_len, 4)) {
+			ath10k_err(ar, "invalid ATH10K_BD_IE_BOARD length: %zu < %zu\n",
+				   buf_len, ALIGN(board_ie_len, 4));
+			ret = -EINVAL;
+			goto out;
+		}
+
+		switch (board_ie_id) {
+		case ATH10K_BD_IE_BOARD_NAME:
+			ath10k_dbg_dump(ar, ATH10K_DBG_BOOT, "board name", "",
+					board_ie_data, board_ie_len);
+
+			if (board_ie_len != strlen(boardname))
+				break;
+
+			ret = memcmp(board_ie_data, boardname, strlen(boardname));
+			if (ret)
+				break;
+
+			name_match_found = true;
+			ath10k_dbg(ar, ATH10K_DBG_BOOT,
+				   "boot found match for name '%s'",
+				   boardname);
+			break;
+		case ATH10K_BD_IE_BOARD_DATA:
+			if (!name_match_found)
+				/* no match found */
+				break;
+
+			ath10k_dbg(ar, ATH10K_DBG_BOOT,
+				   "boot found board data for '%s'",
+				   boardname);
+
+			ar->board_data = board_ie_data;
+			ar->board_len = board_ie_len;
+
+			ret = 0;
+			goto out;
+		default:
+			ath10k_warn(ar, "unknown ATH10K_BD_IE_BOARD found: %d\n",
+				    board_ie_id);
+			break;
+		}
+
+		/* jump over the padding */
+		board_ie_len = ALIGN(board_ie_len, 4);
+
+		buf_len -= board_ie_len;
+		buf += board_ie_len;
 	}
 
-	ar->board = ath10k_fetch_fw_file(ar,
-					 ar->hw_params.fw.dir,
-					 ar->hw_params.fw.board);
+	/* no match found */
+	ret = -ENOENT;
+
+out:
+	return ret;
+}
+
+static int ath10k_core_fetch_board_data_api_n(struct ath10k *ar,
+					      const char *boardname,
+					      const char *filename)
+{
+	size_t len, magic_len, ie_len;
+	struct ath10k_fw_ie *hdr;
+	const u8 *data;
+	int ret, ie_id;
+
+	ar->board = ath10k_fetch_fw_file(ar, ar->hw_params.fw.dir, filename);
 	if (IS_ERR(ar->board))
 		return PTR_ERR(ar->board);
 
-	ar->board_data = ar->board->data;
-	ar->board_len = ar->board->size;
-	ar->spec_board_loaded = false;
+	data = ar->board->data;
+	len = ar->board->size;
+
+	/* magic has extra null byte padded */
+	magic_len = strlen(ATH10K_BOARD_MAGIC) + 1;
+	if (len < magic_len) {
+		ath10k_err(ar, "failed to find magic value in %s/%s, file too short: %zu\n",
+			   ar->hw_params.fw.dir, filename, len);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	if (memcmp(data, ATH10K_BOARD_MAGIC, magic_len)) {
+		ath10k_err(ar, "found invalid board magic\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	/* magic is padded to 4 bytes */
+	magic_len = ALIGN(magic_len, 4);
+	if (len < magic_len) {
+		ath10k_err(ar, "failed: %s/%s too small to contain board data, len: %zu\n",
+			   ar->hw_params.fw.dir, filename, len);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	data += magic_len;
+	len -= magic_len;
+
+	while (len > sizeof(struct ath10k_fw_ie)) {
+		hdr = (struct ath10k_fw_ie *)data;
+		ie_id = le32_to_cpu(hdr->id);
+		ie_len = le32_to_cpu(hdr->len);
+
+		len -= sizeof(*hdr);
+		data = hdr->data;
+
+		if (len < ALIGN(ie_len, 4)) {
+			ath10k_err(ar, "invalid length for board ie_id %d ie_len %zu len %zu\n",
+				   ie_id, ie_len, len);
+			ret = -EINVAL;
+			goto err;
+		}
+
+		switch (ie_id) {
+		case ATH10K_BD_IE_BOARD:
+			ret = ath10k_core_parse_bd_ie_board(ar, data, ie_len,
+							    boardname);
+			if (ret == -ENOENT)
+				/* no match found, continue */
+				break;
+			else if (ret)
+				/* there was an error, bail out */
+				goto err;
+
+			/* board data found */
+			goto out;
+		}
+
+		/* jump over the padding */
+		ie_len = ALIGN(ie_len, 4);
+
+		len -= ie_len;
+		data += ie_len;
+	}
+
+out:
+	if (!ar->board_data || !ar->board_len) {
+		ath10k_err(ar,
+			   "failed to fetch board data for %s from %s/%s\n",
+			   ar->hw_params.fw.dir, boardname, filename);
+		ret = -ENODATA;
+		goto err;
+	}
+
+	return 0;
+
+err:
+	ath10k_core_free_board_files(ar);
+	return ret;
+}
+
+static int ath10k_core_create_board_name(struct ath10k *ar, char *name,
+					 size_t name_len)
+{
+	scnprintf(name, name_len,
+		  "bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x",
+		  ath10k_bus_str(ar->hif.bus),
+		  ar->id.vendor, ar->id.device,
+		  ar->id.subsystem_vendor, ar->id.subsystem_device);
+
+	ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot using board name '%s'\n", name);
 
 	return 0;
 }
 
 static int ath10k_core_fetch_board_file(struct ath10k *ar)
 {
+	char boardname[100];
 	int ret;
 
-	if (strlen(ar->spec_board_id) > 0) {
-		ret = ath10k_core_fetch_spec_board_file(ar);
-		if (ret) {
-			ath10k_info(ar, "failed to load spec board file, falling back to generic: %d\n",
-				    ret);
-			goto generic;
-		}
-
-		ath10k_dbg(ar, ATH10K_DBG_BOOT, "found specific board file for %s\n",
-			   ar->spec_board_id);
-		return 0;
+	ret = ath10k_core_create_board_name(ar, boardname, sizeof(boardname));
+	if (ret) {
+		ath10k_err(ar, "failed to create board name: %d", ret);
+		return ret;
 	}
 
-generic:
-	ret = ath10k_core_fetch_generic_board_file(ar);
+	ar->bd_api = 2;
+	ret = ath10k_core_fetch_board_data_api_n(ar, boardname,
+						 ATH10K_BOARD_API2_FILE);
+	if (!ret)
+		goto success;
+
+	ar->bd_api = 1;
+	ret = ath10k_core_fetch_board_data_api_1(ar);
 	if (ret) {
-		ath10k_err(ar, "failed to fetch generic board data: %d\n", ret);
+		ath10k_err(ar, "failed to fetch board data\n");
 		return ret;
 	}
 
+success:
+	ath10k_dbg(ar, ATH10K_DBG_BOOT, "using board api %d\n", ar->bd_api);
 	return 0;
 }
 
@@ -1626,6 +1802,7 @@ void ath10k_core_unregister(struct ath10k *ar)
 	ath10k_testmode_destroy(ar);
 
 	ath10k_core_free_firmware_files(ar);
+	ath10k_core_free_board_files(ar);
 
 	ath10k_debug_unregister(ar);
 }
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 002de7113e63..af5c0d741659 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -676,10 +676,15 @@ struct ath10k {
 		struct ath10k_swap_code_seg_info *firmware_swap_code_seg_info;
 	} swap;
 
-	char spec_board_id[100];
-	bool spec_board_loaded;
+	struct {
+		u32 vendor;
+		u32 device;
+		u32 subsystem_vendor;
+		u32 subsystem_device;
+	} id;
 
 	int fw_api;
+	int bd_api;
 	enum ath10k_cal_mode cal_mode;
 
 	struct {
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index f316efdbd6c3..7e8f6511b232 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -125,19 +125,21 @@ EXPORT_SYMBOL(ath10k_info);
 void ath10k_print_driver_info(struct ath10k *ar)
 {
 	char fw_features[128] = {};
+	char boardinfo[100];
 
 	ath10k_core_get_fw_features_str(ar, fw_features, sizeof(fw_features));
 
-	ath10k_info(ar, "%s (0x%08x, 0x%08x%s%s%s) fw %s api %d htt-ver %d.%d wmi-op %d htt-op %d cal %s max-sta %d raw %d hwcrypto %d features %s\n",
+	scnprintf(boardinfo, sizeof(boardinfo), "sub %04x:%04x",
+		  ar->id.subsystem_vendor, ar->id.subsystem_device);
+
+	ath10k_info(ar, "%s (0x%08x, 0x%08x %s) fw %s fwapi %d bdapi %d htt-ver %d.%d wmi-op %d htt-op %d cal %s max-sta %d raw %d hwcrypto %d features %s\n",
 		    ar->hw_params.name,
 		    ar->target_version,
 		    ar->chip_id,
-		    (strlen(ar->spec_board_id) > 0 ? ", " : ""),
-		    ar->spec_board_id,
-		    (strlen(ar->spec_board_id) > 0 && !ar->spec_board_loaded
-		     ? " fallback" : ""),
+		    boardinfo,
 		    ar->hw->wiphy->fw_version,
 		    ar->fw_api,
+		    ar->bd_api,
 		    ar->htt.target_version_major,
 		    ar->htt.target_version_minor,
 		    ar->wmi.op_version,
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index bc421a5c5356..291df3d6d484 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -97,6 +97,9 @@ enum qca6174_chip_id_rev {
 
 /* includes also the null byte */
 #define ATH10K_FIRMWARE_MAGIC               "QCA-ATH10K"
+#define ATH10K_BOARD_MAGIC                  "QCA-ATH10K-BOARD"
+
+#define ATH10K_BOARD_API2_FILE         "board-2.bin"
 
 #define REG_DUMP_COUNT_QCA988X 60
 
@@ -159,6 +162,16 @@ enum ath10k_fw_htt_op_version {
 	ATH10K_FW_HTT_OP_VERSION_MAX,
 };
 
+enum ath10k_bd_ie_type {
+	/* contains sub IEs of enum ath10k_bd_ie_board_type */
+	ATH10K_BD_IE_BOARD = 0,
+};
+
+enum ath10k_bd_ie_board_type {
+	ATH10K_BD_IE_BOARD_NAME = 0,
+	ATH10K_BD_IE_BOARD_DATA = 1,
+};
+
 enum ath10k_hw_rev {
 	ATH10K_HW_QCA988X,
 	ATH10K_HW_QCA6174,
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 4401779af253..863117bd18ea 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -2918,7 +2918,9 @@ static int ath10k_pci_probe(struct pci_dev *pdev,
 		return -ENOMEM;
 	}
 
-	ath10k_dbg(ar, ATH10K_DBG_PCI, "pci probe\n");
+	ath10k_dbg(ar, ATH10K_DBG_BOOT, "pci probe %04x:%04x %04x:%04x\n",
+		   pdev->vendor, pdev->device,
+		   pdev->subsystem_vendor, pdev->subsystem_device);
 
 	ar_pci = ath10k_pci_priv(ar);
 	ar_pci->pdev = pdev;
@@ -2926,11 +2928,10 @@ static int ath10k_pci_probe(struct pci_dev *pdev,
 	ar_pci->ar = ar;
 	ar->dev_id = pci_dev->device;
 
-	if (pdev->subsystem_vendor || pdev->subsystem_device)
-		scnprintf(ar->spec_board_id, sizeof(ar->spec_board_id),
-			  "%04x:%04x:%04x:%04x",
-			  pdev->vendor, pdev->device,
-			  pdev->subsystem_vendor, pdev->subsystem_device);
+	ar->id.vendor = pdev->vendor;
+	ar->id.device = pdev->device;
+	ar->id.subsystem_vendor = pdev->subsystem_vendor;
+	ar->id.subsystem_device = pdev->subsystem_device;
 
 	spin_lock_init(&ar_pci->ce_lock);
 	spin_lock_init(&ar_pci->ps_lock);
@@ -3084,13 +3085,16 @@ MODULE_FIRMWARE(QCA988X_HW_2_0_FW_DIR "/" ATH10K_FW_API3_FILE);
 MODULE_FIRMWARE(QCA988X_HW_2_0_FW_DIR "/" ATH10K_FW_API4_FILE);
 MODULE_FIRMWARE(QCA988X_HW_2_0_FW_DIR "/" ATH10K_FW_API5_FILE);
 MODULE_FIRMWARE(QCA988X_HW_2_0_FW_DIR "/" QCA988X_HW_2_0_BOARD_DATA_FILE);
+MODULE_FIRMWARE(QCA988X_HW_2_0_FW_DIR "/" ATH10K_BOARD_API2_FILE);
 
 /* QCA6174 2.1 firmware files */
 MODULE_FIRMWARE(QCA6174_HW_2_1_FW_DIR "/" ATH10K_FW_API4_FILE);
 MODULE_FIRMWARE(QCA6174_HW_2_1_FW_DIR "/" ATH10K_FW_API5_FILE);
 MODULE_FIRMWARE(QCA6174_HW_2_1_FW_DIR "/" QCA6174_HW_2_1_BOARD_DATA_FILE);
+MODULE_FIRMWARE(QCA6174_HW_2_1_FW_DIR "/" ATH10K_BOARD_API2_FILE);
 
 /* QCA6174 3.1 firmware files */
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_FW_API4_FILE);
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_FW_API5_FILE);
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" QCA6174_HW_3_0_BOARD_DATA_FILE);
+MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_BOARD_API2_FILE);
-- 
cgit v1.2.3


From db0984e51a187f5bbe41231af7e671cc12586346 Mon Sep 17 00:00:00 2001
From: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Date: Fri, 9 Oct 2015 11:55:59 +0300
Subject: ath10k: select board data based on BMI chip id and board id

QCA99X0 uses radio specific board names based on chip id and
board id combinations. We get these IDs from the target using BMI after otp.bin
has been started.

This patch reorders the call to the function ath10k_core_fetch_board_file
so that we have OTP binary before requesting for boardid-chipid. We get this
OTP data after parsing firmware-N.bin.

[kvalo@qca.qualcomm.com: try BMI_PARAM_GET_EEPROM_BOARD_ID with
 all boards and detect if command is not supported]
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/bmi.h   | 10 +++++
 drivers/net/wireless/ath/ath10k/core.c  | 79 ++++++++++++++++++++++++++++++---
 drivers/net/wireless/ath/ath10k/core.h  |  4 ++
 drivers/net/wireless/ath/ath10k/debug.c |  8 +++-
 4 files changed, 93 insertions(+), 8 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/bmi.h b/drivers/net/wireless/ath/ath10k/bmi.h
index df7c7616533b..7d3231acfb24 100644
--- a/drivers/net/wireless/ath/ath10k/bmi.h
+++ b/drivers/net/wireless/ath/ath10k/bmi.h
@@ -82,6 +82,16 @@ enum bmi_cmd_id {
 
 #define BMI_NVRAM_SEG_NAME_SZ 16
 
+#define BMI_PARAM_GET_EEPROM_BOARD_ID 0x10
+
+#define ATH10K_BMI_BOARD_ID_FROM_OTP_MASK   0x7c00
+#define ATH10K_BMI_BOARD_ID_FROM_OTP_LSB    10
+
+#define ATH10K_BMI_CHIP_ID_FROM_OTP_MASK    0x18000
+#define ATH10K_BMI_CHIP_ID_FROM_OTP_LSB     15
+
+#define ATH10K_BMI_BOARD_ID_STATUS_MASK 0xff
+
 struct bmi_cmd {
 	__le32 id; /* enum bmi_cmd_id */
 	union {
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 99a4e145c9b6..13de3617d5ab 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -448,6 +448,56 @@ out:
 	return ret;
 }
 
+static int ath10k_core_get_board_id_from_otp(struct ath10k *ar)
+{
+	u32 result, address;
+	u8 board_id, chip_id;
+	int ret;
+
+	address = ar->hw_params.patch_load_addr;
+
+	if (!ar->otp_data || !ar->otp_len) {
+		ath10k_warn(ar,
+			    "failed to retrieve board id because of invalid otp\n");
+		return -ENODATA;
+	}
+
+	ath10k_dbg(ar, ATH10K_DBG_BOOT,
+		   "boot upload otp to 0x%x len %zd for board id\n",
+		   address, ar->otp_len);
+
+	ret = ath10k_bmi_fast_download(ar, address, ar->otp_data, ar->otp_len);
+	if (ret) {
+		ath10k_err(ar, "could not write otp for board id check: %d\n",
+			   ret);
+		return ret;
+	}
+
+	ret = ath10k_bmi_execute(ar, address, BMI_PARAM_GET_EEPROM_BOARD_ID,
+				 &result);
+	if (ret) {
+		ath10k_err(ar, "could not execute otp for board id check: %d\n",
+			   ret);
+		return ret;
+	}
+
+	board_id = MS(result, ATH10K_BMI_BOARD_ID_FROM_OTP);
+	chip_id = MS(result, ATH10K_BMI_CHIP_ID_FROM_OTP);
+
+	ath10k_dbg(ar, ATH10K_DBG_BOOT,
+		   "boot get otp board id result 0x%08x board_id %d chip_id %d\n",
+		   result, board_id, chip_id);
+
+	if ((result & ATH10K_BMI_BOARD_ID_STATUS_MASK) != 0)
+		return -EOPNOTSUPP;
+
+	ar->id.bmi_ids_valid = true;
+	ar->id.bmi_board_id = board_id;
+	ar->id.bmi_chip_id = chip_id;
+
+	return 0;
+}
+
 static int ath10k_download_and_run_otp(struct ath10k *ar)
 {
 	u32 result, address = ar->hw_params.patch_load_addr;
@@ -792,12 +842,22 @@ err:
 static int ath10k_core_create_board_name(struct ath10k *ar, char *name,
 					 size_t name_len)
 {
+	if (ar->id.bmi_ids_valid) {
+		scnprintf(name, name_len,
+			  "bus=%s,bmi-chip-id=%d,bmi-board-id=%d",
+			  ath10k_bus_str(ar->hif.bus),
+			  ar->id.bmi_chip_id,
+			  ar->id.bmi_board_id);
+		goto out;
+	}
+
 	scnprintf(name, name_len,
 		  "bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x",
 		  ath10k_bus_str(ar->hif.bus),
 		  ar->id.vendor, ar->id.device,
 		  ar->id.subsystem_vendor, ar->id.subsystem_device);
 
+out:
 	ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot using board name '%s'\n", name);
 
 	return 0;
@@ -1060,12 +1120,6 @@ static int ath10k_core_fetch_firmware_files(struct ath10k *ar)
 	/* calibration file is optional, don't check for any errors */
 	ath10k_fetch_cal_file(ar);
 
-	ret = ath10k_core_fetch_board_file(ar);
-	if (ret) {
-		ath10k_err(ar, "failed to fetch board file: %d\n", ret);
-		return ret;
-	}
-
 	ar->fw_api = 5;
 	ath10k_dbg(ar, ATH10K_DBG_BOOT, "trying fw api %d\n", ar->fw_api);
 
@@ -1675,6 +1729,19 @@ static int ath10k_core_probe_fw(struct ath10k *ar)
 		goto err_power_down;
 	}
 
+	ret = ath10k_core_get_board_id_from_otp(ar);
+	if (ret && ret != -EOPNOTSUPP) {
+		ath10k_err(ar, "failed to get board id from otp for qca99x0: %d\n",
+			   ret);
+		return ret;
+	}
+
+	ret = ath10k_core_fetch_board_file(ar);
+	if (ret) {
+		ath10k_err(ar, "failed to fetch board file: %d\n", ret);
+		goto err_free_firmware_files;
+	}
+
 	ret = ath10k_core_init_firmware_features(ar);
 	if (ret) {
 		ath10k_err(ar, "fatal problem with firmware features: %d\n",
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index af5c0d741659..7cc7cdd56c95 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -681,6 +681,10 @@ struct ath10k {
 		u32 device;
 		u32 subsystem_vendor;
 		u32 subsystem_device;
+
+		bool bmi_ids_valid;
+		u8 bmi_board_id;
+		u8 bmi_chip_id;
 	} id;
 
 	int fw_api;
diff --git a/drivers/net/wireless/ath/ath10k/debug.c b/drivers/net/wireless/ath/ath10k/debug.c
index 7e8f6511b232..eab71e2eb4d7 100644
--- a/drivers/net/wireless/ath/ath10k/debug.c
+++ b/drivers/net/wireless/ath/ath10k/debug.c
@@ -129,8 +129,12 @@ void ath10k_print_driver_info(struct ath10k *ar)
 
 	ath10k_core_get_fw_features_str(ar, fw_features, sizeof(fw_features));
 
-	scnprintf(boardinfo, sizeof(boardinfo), "sub %04x:%04x",
-		  ar->id.subsystem_vendor, ar->id.subsystem_device);
+	if (ar->id.bmi_ids_valid)
+		scnprintf(boardinfo, sizeof(boardinfo), "bmi %d:%d",
+			  ar->id.bmi_chip_id, ar->id.bmi_board_id);
+	else
+		scnprintf(boardinfo, sizeof(boardinfo), "sub %04x:%04x",
+			  ar->id.subsystem_vendor, ar->id.subsystem_device);
 
 	ath10k_info(ar, "%s (0x%08x, 0x%08x %s) fw %s fwapi %d bdapi %d htt-ver %d.%d wmi-op %d htt-op %d cal %s max-sta %d raw %d hwcrypto %d features %s\n",
 		    ar->hw_params.name,
-- 
cgit v1.2.3


From 62f77f095c27dc6b3536735aa960a8bb21e4c5eb Mon Sep 17 00:00:00 2001
From: Maharaja <c_mkenna@qti.qualcomm.com>
Date: Wed, 21 Oct 2015 11:49:18 +0300
Subject: ath10k: enable adaptive CCA

European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.

Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.

The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.

Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c    |  1 +
 drivers/net/wireless/ath/ath10k/core.h    |  3 +++
 drivers/net/wireless/ath/ath10k/mac.c     | 12 ++++++++++++
 drivers/net/wireless/ath/ath10k/wmi-ops.h | 25 +++++++++++++++++++++++++
 drivers/net/wireless/ath/ath10k/wmi.c     | 31 +++++++++++++++++++++++++++++++
 drivers/net/wireless/ath/ath10k/wmi.h     | 13 +++++++++++++
 6 files changed, 85 insertions(+)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 13de3617d5ab..e70e715ae1a7 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -151,6 +151,7 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_NO_NWIFI_DECAP_4ADDR_PADDING] = "no-4addr-pad",
 	[ATH10K_FW_FEATURE_SUPPORTS_SKIP_CLOCK_INIT] = "skip-clock-init",
 	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
+	[ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA] = "adaptive-cca",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7cc7cdd56c95..3f88aa09086b 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -497,6 +497,9 @@ enum ath10k_fw_features {
 	 */
 	ATH10K_FW_FEATURE_RAW_MODE_SUPPORT = 10,
 
+	/* Firmware Supports Adaptive CCA*/
+	ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA = 11,
+
 	/* keep last */
 	ATH10K_FW_FEATURE_COUNT,
 };
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 484c1a10372f..769d7d830770 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -3905,6 +3905,18 @@ static int ath10k_start(struct ieee80211_hw *hw)
 		goto err_core_stop;
 	}
 
+	if (test_bit(ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA,
+		     ar->fw_features)) {
+		ret = ath10k_wmi_pdev_enable_adaptive_cca(ar, 1,
+							  WMI_CCA_DETECT_LEVEL_AUTO,
+							  WMI_CCA_DETECT_MARGIN_AUTO);
+		if (ret) {
+			ath10k_warn(ar, "failed to enable adaptive cca: %d\n",
+				    ret);
+			goto err_core_stop;
+		}
+	}
+
 	ret = ath10k_wmi_pdev_set_param(ar,
 					ar->wmi.pdev_param->ani_enable, 1);
 	if (ret) {
diff --git a/drivers/net/wireless/ath/ath10k/wmi-ops.h b/drivers/net/wireless/ath/ath10k/wmi-ops.h
index b54aa08cb25c..8f4f6a892581 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-ops.h
+++ b/drivers/net/wireless/ath/ath10k/wmi-ops.h
@@ -182,6 +182,10 @@ struct wmi_ops {
 	void (*fw_stats_fill)(struct ath10k *ar,
 			      struct ath10k_fw_stats *fw_stats,
 			      char *buf);
+	struct sk_buff *(*gen_pdev_enable_adaptive_cca)(struct ath10k *ar,
+							u8 enable,
+							u32 detect_level,
+							u32 detect_margin);
 };
 
 int ath10k_wmi_cmd_send(struct ath10k *ar, struct sk_buff *skb, u32 cmd_id);
@@ -1302,4 +1306,25 @@ ath10k_wmi_fw_stats_fill(struct ath10k *ar, struct ath10k_fw_stats *fw_stats,
 	ar->wmi.ops->fw_stats_fill(ar, fw_stats, buf);
 	return 0;
 }
+
+static inline int
+ath10k_wmi_pdev_enable_adaptive_cca(struct ath10k *ar, u8 enable,
+				    u32 detect_level, u32 detect_margin)
+{
+	struct sk_buff *skb;
+
+	if (!ar->wmi.ops->gen_pdev_enable_adaptive_cca)
+		return -EOPNOTSUPP;
+
+	skb = ar->wmi.ops->gen_pdev_enable_adaptive_cca(ar, enable,
+							detect_level,
+							detect_margin);
+
+	if (IS_ERR(skb))
+		return PTR_ERR(skb);
+
+	return ath10k_wmi_cmd_send(ar, skb,
+				   ar->wmi.cmd->pdev_enable_adaptive_cca_cmdid);
+}
+
 #endif
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 6e7d7a7f6a97..2b32f02992f3 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -148,6 +148,7 @@ static struct wmi_cmd_map wmi_cmd_map = {
 	.gpio_config_cmdid = WMI_GPIO_CONFIG_CMDID,
 	.gpio_output_cmdid = WMI_GPIO_OUTPUT_CMDID,
 	.pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
+	.pdev_enable_adaptive_cca_cmdid = WMI_CMD_UNSUPPORTED,
 	.scan_update_request_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_standby_response_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_resume_response_cmdid = WMI_CMD_UNSUPPORTED,
@@ -313,6 +314,7 @@ static struct wmi_cmd_map wmi_10x_cmd_map = {
 	.gpio_config_cmdid = WMI_10X_GPIO_CONFIG_CMDID,
 	.gpio_output_cmdid = WMI_10X_GPIO_OUTPUT_CMDID,
 	.pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
+	.pdev_enable_adaptive_cca_cmdid = WMI_CMD_UNSUPPORTED,
 	.scan_update_request_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_standby_response_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_resume_response_cmdid = WMI_CMD_UNSUPPORTED,
@@ -477,6 +479,7 @@ static struct wmi_cmd_map wmi_10_2_4_cmd_map = {
 	.gpio_config_cmdid = WMI_10_2_GPIO_CONFIG_CMDID,
 	.gpio_output_cmdid = WMI_10_2_GPIO_OUTPUT_CMDID,
 	.pdev_get_temperature_cmdid = WMI_10_2_PDEV_GET_TEMPERATURE_CMDID,
+	.pdev_enable_adaptive_cca_cmdid = WMI_10_2_SET_CCA_PARAMS,
 	.scan_update_request_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_standby_response_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_resume_response_cmdid = WMI_CMD_UNSUPPORTED,
@@ -1407,6 +1410,7 @@ static struct wmi_cmd_map wmi_10_2_cmd_map = {
 	.gpio_config_cmdid = WMI_10_2_GPIO_CONFIG_CMDID,
 	.gpio_output_cmdid = WMI_10_2_GPIO_OUTPUT_CMDID,
 	.pdev_get_temperature_cmdid = WMI_CMD_UNSUPPORTED,
+	.pdev_enable_adaptive_cca_cmdid = WMI_CMD_UNSUPPORTED,
 	.scan_update_request_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_standby_response_cmdid = WMI_CMD_UNSUPPORTED,
 	.vdev_resume_response_cmdid = WMI_CMD_UNSUPPORTED,
@@ -6996,6 +7000,28 @@ unlock:
 		buf[len] = 0;
 }
 
+static struct sk_buff *
+ath10k_wmi_op_gen_pdev_enable_adaptive_cca(struct ath10k *ar, u8 enable,
+					   u32 detect_level, u32 detect_margin)
+{
+	struct wmi_pdev_set_adaptive_cca_params *cmd;
+	struct sk_buff *skb;
+
+	skb = ath10k_wmi_alloc_skb(ar, sizeof(*cmd));
+	if (!skb)
+		return ERR_PTR(-ENOMEM);
+
+	cmd = (struct wmi_pdev_set_adaptive_cca_params *)skb->data;
+	cmd->enable = __cpu_to_le32(enable);
+	cmd->cca_detect_level = __cpu_to_le32(detect_level);
+	cmd->cca_detect_margin = __cpu_to_le32(detect_margin);
+
+	ath10k_dbg(ar, ATH10K_DBG_WMI,
+		   "wmi pdev set adaptive cca params enable:%d detection level:%d detection margin:%d\n",
+		   enable, detect_level, detect_margin);
+	return skb;
+}
+
 static const struct wmi_ops wmi_ops = {
 	.rx = ath10k_wmi_op_rx,
 	.map_svc = wmi_main_svc_map,
@@ -7059,6 +7085,7 @@ static const struct wmi_ops wmi_ops = {
 	/* .gen_prb_tmpl not implemented */
 	/* .gen_p2p_go_bcn_ie not implemented */
 	/* .gen_adaptive_qcs not implemented */
+	/* .gen_pdev_enable_adaptive_cca not implemented */
 };
 
 static const struct wmi_ops wmi_10_1_ops = {
@@ -7125,6 +7152,7 @@ static const struct wmi_ops wmi_10_1_ops = {
 	/* .gen_prb_tmpl not implemented */
 	/* .gen_p2p_go_bcn_ie not implemented */
 	/* .gen_adaptive_qcs not implemented */
+	/* .gen_pdev_enable_adaptive_cca not implemented */
 };
 
 static const struct wmi_ops wmi_10_2_ops = {
@@ -7188,6 +7216,7 @@ static const struct wmi_ops wmi_10_2_ops = {
 	.gen_addba_set_resp = ath10k_wmi_op_gen_addba_set_resp,
 	.gen_delba_send = ath10k_wmi_op_gen_delba_send,
 	.fw_stats_fill = ath10k_wmi_10x_op_fw_stats_fill,
+	/* .gen_pdev_enable_adaptive_cca not implemented */
 };
 
 static const struct wmi_ops wmi_10_2_4_ops = {
@@ -7251,6 +7280,8 @@ static const struct wmi_ops wmi_10_2_4_ops = {
 	.gen_delba_send = ath10k_wmi_op_gen_delba_send,
 	.gen_pdev_get_tpc_config = ath10k_wmi_10_2_4_op_gen_pdev_get_tpc_config,
 	.fw_stats_fill = ath10k_wmi_10x_op_fw_stats_fill,
+	.gen_pdev_enable_adaptive_cca =
+		ath10k_wmi_op_gen_pdev_enable_adaptive_cca,
 	/* .gen_bcn_tmpl not implemented */
 	/* .gen_prb_tmpl not implemented */
 	/* .gen_p2p_go_bcn_ie not implemented */
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 6e84d1c1a6ca..c6718e7422f5 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -772,6 +772,7 @@ struct wmi_cmd_map {
 	u32 mu_cal_start_cmdid;
 	u32 set_cca_params_cmdid;
 	u32 pdev_bss_chan_info_request_cmdid;
+	u32 pdev_enable_adaptive_cca_cmdid;
 };
 
 /*
@@ -1381,6 +1382,9 @@ enum wmi_10_2_cmd_id {
 	WMI_10_2_VDEV_ATF_REQUEST_CMDID,
 	WMI_10_2_PEER_ATF_REQUEST_CMDID,
 	WMI_10_2_PDEV_GET_TEMPERATURE_CMDID,
+	WMI_10_2_MU_CAL_START_CMDID,
+	WMI_10_2_SET_LTEU_CONFIG_CMDID,
+	WMI_10_2_SET_CCA_PARAMS,
 	WMI_10_2_PDEV_UTF_CMDID = WMI_10_2_END_CMDID - 1,
 };
 
@@ -6094,6 +6098,15 @@ enum wmi_txbf_conf {
 	WMI_TXBF_CONF_AFTER_ASSOC,
 };
 
+#define	WMI_CCA_DETECT_LEVEL_AUTO	0
+#define	WMI_CCA_DETECT_MARGIN_AUTO	0
+
+struct wmi_pdev_set_adaptive_cca_params {
+	__le32 enable;
+	__le32 cca_detect_level;
+	__le32 cca_detect_margin;
+} __packed;
+
 struct ath10k;
 struct ath10k_vif;
 struct ath10k_fw_stats_pdev;
-- 
cgit v1.2.3


From a81a98cee94519807e826e199bb579a546efa289 Mon Sep 17 00:00:00 2001
From: Alan Liu <alanliu@qca.qualcomm.com>
Date: Wed, 28 Oct 2015 21:38:32 +0200
Subject: ath10k: add FW API support to test mode

Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.

Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c     |   4 +-
 drivers/net/wireless/ath/ath10k/core.h     |   5 +-
 drivers/net/wireless/ath/ath10k/hw.h       |   1 +
 drivers/net/wireless/ath/ath10k/testmode.c | 202 ++++++++++++++++++++++++++---
 drivers/net/wireless/ath/ath10k/wmi-tlv.c  |  14 ++
 5 files changed, 205 insertions(+), 21 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index e70e715ae1a7..519a1b91f309 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -569,8 +569,8 @@ static int ath10k_download_fw(struct ath10k *ar, enum ath10k_firmware_mode mode)
 		}
 		break;
 	case ATH10K_FIRMWARE_MODE_UTF:
-		data = ar->testmode.utf->data;
-		data_len = ar->testmode.utf->size;
+		data = ar->testmode.utf_firmware_data;
+		data_len = ar->testmode.utf_firmware_len;
 		mode_name = "utf";
 		break;
 	default:
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 3f88aa09086b..9bd264f3031c 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -817,9 +817,12 @@ struct ath10k {
 	struct {
 		/* protected by conf_mutex */
 		const struct firmware *utf;
+		char utf_version[32];
+		const void *utf_firmware_data;
+		size_t utf_firmware_len;
 		DECLARE_BITMAP(orig_fw_features, ATH10K_FW_FEATURE_COUNT);
 		enum ath10k_fw_wmi_op_version orig_wmi_op_version;
-
+		enum ath10k_fw_wmi_op_version op_version;
 		/* protected by data_lock */
 		bool utf_monitor;
 	} testmode;
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 2d87737e35ff..0c8ea0226684 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -94,6 +94,7 @@ enum qca6174_chip_id_rev {
 #define ATH10K_FW_API5_FILE		"firmware-5.bin"
 
 #define ATH10K_FW_UTF_FILE		"utf.bin"
+#define ATH10K_FW_UTF_API2_FILE		"utf-2.bin"
 
 /* includes also the null byte */
 #define ATH10K_FIRMWARE_MAGIC               "QCA-ATH10K"
diff --git a/drivers/net/wireless/ath/ath10k/testmode.c b/drivers/net/wireless/ath/ath10k/testmode.c
index b084f88da102..1d5a2fdcbf56 100644
--- a/drivers/net/wireless/ath/ath10k/testmode.c
+++ b/drivers/net/wireless/ath/ath10k/testmode.c
@@ -139,11 +139,181 @@ static int ath10k_tm_cmd_get_version(struct ath10k *ar, struct nlattr *tb[])
 	return cfg80211_testmode_reply(skb);
 }
 
-static int ath10k_tm_cmd_utf_start(struct ath10k *ar, struct nlattr *tb[])
+static int ath10k_tm_fetch_utf_firmware_api_2(struct ath10k *ar)
+{
+	size_t len, magic_len, ie_len;
+	struct ath10k_fw_ie *hdr;
+	char filename[100];
+	__le32 *version;
+	const u8 *data;
+	int ie_id, ret;
+
+	snprintf(filename, sizeof(filename), "%s/%s",
+		 ar->hw_params.fw.dir, ATH10K_FW_UTF_API2_FILE);
+
+	/* load utf firmware image */
+	ret = request_firmware(&ar->testmode.utf, filename, ar->dev);
+	if (ret) {
+		ath10k_warn(ar, "failed to retrieve utf firmware '%s': %d\n",
+			    filename, ret);
+		return ret;
+	}
+
+	data = ar->testmode.utf->data;
+	len = ar->testmode.utf->size;
+
+	/* FIXME: call release_firmware() in error cases */
+
+	/* magic also includes the null byte, check that as well */
+	magic_len = strlen(ATH10K_FIRMWARE_MAGIC) + 1;
+
+	if (len < magic_len) {
+		ath10k_err(ar, "utf firmware file is too small to contain magic\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	if (memcmp(data, ATH10K_FIRMWARE_MAGIC, magic_len) != 0) {
+		ath10k_err(ar, "invalid firmware magic\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	/* jump over the padding */
+	magic_len = ALIGN(magic_len, 4);
+
+	len -= magic_len;
+	data += magic_len;
+
+	/* loop elements */
+	while (len > sizeof(struct ath10k_fw_ie)) {
+		hdr = (struct ath10k_fw_ie *)data;
+
+		ie_id = le32_to_cpu(hdr->id);
+		ie_len = le32_to_cpu(hdr->len);
+
+		len -= sizeof(*hdr);
+		data += sizeof(*hdr);
+
+		if (len < ie_len) {
+			ath10k_err(ar, "invalid length for FW IE %d (%zu < %zu)\n",
+				   ie_id, len, ie_len);
+			ret = -EINVAL;
+			goto err;
+		}
+
+		switch (ie_id) {
+		case ATH10K_FW_IE_FW_VERSION:
+			if (ie_len > sizeof(ar->testmode.utf_version) - 1)
+				break;
+
+			memcpy(ar->testmode.utf_version, data, ie_len);
+			ar->testmode.utf_version[ie_len] = '\0';
+
+			ath10k_dbg(ar, ATH10K_DBG_TESTMODE,
+				   "testmode found fw utf version %s\n",
+				   ar->testmode.utf_version);
+			break;
+		case ATH10K_FW_IE_TIMESTAMP:
+			/* ignore timestamp, but don't warn about it either */
+			break;
+		case ATH10K_FW_IE_FW_IMAGE:
+			ath10k_dbg(ar, ATH10K_DBG_TESTMODE,
+				   "testmode found fw image ie (%zd B)\n",
+				   ie_len);
+
+			ar->testmode.utf_firmware_data = data;
+			ar->testmode.utf_firmware_len = ie_len;
+			break;
+		case ATH10K_FW_IE_WMI_OP_VERSION:
+			if (ie_len != sizeof(u32))
+				break;
+			version = (__le32 *)data;
+			ar->testmode.op_version = le32_to_cpup(version);
+			ath10k_dbg(ar, ATH10K_DBG_TESTMODE, "testmode found fw ie wmi op version %d\n",
+				   ar->testmode.op_version);
+			break;
+		default:
+			ath10k_warn(ar, "Unknown testmode FW IE: %u\n",
+				    le32_to_cpu(hdr->id));
+			break;
+		}
+		/* jump over the padding */
+		ie_len = ALIGN(ie_len, 4);
+
+		len -= ie_len;
+		data += ie_len;
+	}
+
+	if (!ar->testmode.utf_firmware_data || !ar->testmode.utf_firmware_len) {
+		ath10k_err(ar, "No ATH10K_FW_IE_FW_IMAGE found\n");
+		ret = -EINVAL;
+		goto err;
+	}
+
+	return 0;
+
+err:
+	release_firmware(ar->testmode.utf);
+
+	return ret;
+}
+
+static int ath10k_tm_fetch_utf_firmware_api_1(struct ath10k *ar)
 {
 	char filename[100];
 	int ret;
 
+	snprintf(filename, sizeof(filename), "%s/%s",
+		 ar->hw_params.fw.dir, ATH10K_FW_UTF_FILE);
+
+	/* load utf firmware image */
+	ret = request_firmware(&ar->testmode.utf, filename, ar->dev);
+	if (ret) {
+		ath10k_warn(ar, "failed to retrieve utf firmware '%s': %d\n",
+			    filename, ret);
+		return ret;
+	}
+
+	/* We didn't find FW UTF API 1 ("utf.bin") does not advertise
+	 * firmware features. Do an ugly hack where we force the firmware
+	 * features to match with 10.1 branch so that wmi.c will use the
+	 * correct WMI interface.
+	 */
+
+	ar->testmode.op_version = ATH10K_FW_WMI_OP_VERSION_10_1;
+	ar->testmode.utf_firmware_data = ar->testmode.utf->data;
+	ar->testmode.utf_firmware_len = ar->testmode.utf->size;
+
+	return 0;
+}
+
+static int ath10k_tm_fetch_firmware(struct ath10k *ar)
+{
+	int ret;
+
+	ret = ath10k_tm_fetch_utf_firmware_api_2(ar);
+	if (ret == 0) {
+		ath10k_dbg(ar, ATH10K_DBG_TESTMODE, "testmode using fw utf api 2");
+		return 0;
+	}
+
+	ret = ath10k_tm_fetch_utf_firmware_api_1(ar);
+	if (ret) {
+		ath10k_err(ar, "failed to fetch utf firmware binary: %d", ret);
+		return ret;
+	}
+
+	ath10k_dbg(ar, ATH10K_DBG_TESTMODE, "testmode using utf api 1");
+
+	return 0;
+}
+
+static int ath10k_tm_cmd_utf_start(struct ath10k *ar, struct nlattr *tb[])
+{
+	const char *ver;
+	int ret;
+
 	ath10k_dbg(ar, ATH10K_DBG_TESTMODE, "testmode cmd utf start\n");
 
 	mutex_lock(&ar->conf_mutex);
@@ -165,36 +335,27 @@ static int ath10k_tm_cmd_utf_start(struct ath10k *ar, struct nlattr *tb[])
 		goto err;
 	}
 
-	snprintf(filename, sizeof(filename), "%s/%s",
-		 ar->hw_params.fw.dir, ATH10K_FW_UTF_FILE);
-
-	/* load utf firmware image */
-	ret = request_firmware(&ar->testmode.utf, filename, ar->dev);
+	ret = ath10k_tm_fetch_firmware(ar);
 	if (ret) {
-		ath10k_warn(ar, "failed to retrieve utf firmware '%s': %d\n",
-			    filename, ret);
+		ath10k_err(ar, "failed to fetch UTF firmware: %d", ret);
 		goto err;
 	}
 
 	spin_lock_bh(&ar->data_lock);
-
 	ar->testmode.utf_monitor = true;
-
 	spin_unlock_bh(&ar->data_lock);
-
 	BUILD_BUG_ON(sizeof(ar->fw_features) !=
 		     sizeof(ar->testmode.orig_fw_features));
 
 	memcpy(ar->testmode.orig_fw_features, ar->fw_features,
 	       sizeof(ar->fw_features));
 	ar->testmode.orig_wmi_op_version = ar->wmi.op_version;
-
-	/* utf.bin firmware image does not advertise firmware features. Do
-	 * an ugly hack where we force the firmware features so that wmi.c
-	 * will use the correct WMI interface.
-	 */
 	memset(ar->fw_features, 0, sizeof(ar->fw_features));
-	ar->wmi.op_version = ATH10K_FW_WMI_OP_VERSION_10_1;
+
+	ar->wmi.op_version = ar->testmode.op_version;
+
+	ath10k_dbg(ar, ATH10K_DBG_TESTMODE, "testmode wmi version %d\n",
+		   ar->wmi.op_version);
 
 	ret = ath10k_hif_power_up(ar);
 	if (ret) {
@@ -212,7 +373,12 @@ static int ath10k_tm_cmd_utf_start(struct ath10k *ar, struct nlattr *tb[])
 
 	ar->state = ATH10K_STATE_UTF;
 
-	ath10k_info(ar, "UTF firmware started\n");
+	if (strlen(ar->testmode.utf_version) > 0)
+		ver = ar->testmode.utf_version;
+	else
+		ver = "API 1";
+
+	ath10k_info(ar, "UTF firmware %s started\n", ver);
 
 	mutex_unlock(&ar->conf_mutex);
 
diff --git a/drivers/net/wireless/ath/ath10k/wmi-tlv.c b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
index 8f835480a62c..6fbd17b69469 100644
--- a/drivers/net/wireless/ath/ath10k/wmi-tlv.c
+++ b/drivers/net/wireless/ath/ath10k/wmi-tlv.c
@@ -23,6 +23,7 @@
 #include "wmi-ops.h"
 #include "wmi-tlv.h"
 #include "p2p.h"
+#include "testmode.h"
 
 /***************/
 /* TLV helpers */
@@ -419,6 +420,7 @@ static void ath10k_wmi_tlv_op_rx(struct ath10k *ar, struct sk_buff *skb)
 {
 	struct wmi_cmd_hdr *cmd_hdr;
 	enum wmi_tlv_event_id id;
+	bool consumed;
 
 	cmd_hdr = (struct wmi_cmd_hdr *)skb->data;
 	id = MS(__le32_to_cpu(cmd_hdr->cmd_id), WMI_CMD_HDR_CMD_ID);
@@ -428,6 +430,18 @@ static void ath10k_wmi_tlv_op_rx(struct ath10k *ar, struct sk_buff *skb)
 
 	trace_ath10k_wmi_event(ar, id, skb->data, skb->len);
 
+	consumed = ath10k_tm_event_wmi(ar, id, skb);
+
+	/* Ready event must be handled normally also in UTF mode so that we
+	 * know the UTF firmware has booted, others we are just bypass WMI
+	 * events to testmode.
+	 */
+	if (consumed && id != WMI_TLV_READY_EVENTID) {
+		ath10k_dbg(ar, ATH10K_DBG_WMI,
+			   "wmi tlv testmode consumed 0x%x\n", id);
+		goto out;
+	}
+
 	switch (id) {
 	case WMI_TLV_MGMT_RX_EVENTID:
 		ath10k_wmi_event_mgmt_rx(ar, skb);
-- 
cgit v1.2.3


From a226b519d43a2a6b37267fea051aacb4a79c9614 Mon Sep 17 00:00:00 2001
From: Bartosz Markowski <bartosz.markowski@tieto.com>
Date: Wed, 28 Oct 2015 15:09:53 +0100
Subject: ath10k: add QCA9377 chipset support

Add the hardware name, revision and update the pci_id table.

Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.

QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c      | 16 ++++++++++++++++
 drivers/net/wireless/ath/ath10k/hw.h        | 11 +++++++++++
 drivers/net/wireless/ath/ath10k/pci.c       | 18 ++++++++++++++++++
 drivers/net/wireless/ath/ath10k/targaddrs.h |  3 +++
 4 files changed, 48 insertions(+)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 519a1b91f309..aa9bd92ac4ed 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -137,6 +137,21 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 			.board_ext_size = QCA99X0_BOARD_EXT_DATA_SZ,
 		},
 	},
+	{
+		.id = QCA9377_HW_1_0_DEV_VERSION,
+		.name = "qca9377 hw1.0",
+		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
+		.uart_pin = 7,
+		.otp_exe_param = 0,
+		.fw = {
+			.dir = QCA9377_HW_1_0_FW_DIR,
+			.fw = QCA9377_HW_1_0_FW_FILE,
+			.otp = QCA9377_HW_1_0_OTP_FILE,
+			.board = QCA9377_HW_1_0_BOARD_DATA_FILE,
+			.board_size = QCA9377_BOARD_DATA_SZ,
+			.board_ext_size = QCA9377_BOARD_EXT_DATA_SZ,
+		},
+	},
 };
 
 static const char *const ath10k_core_fw_feature_str[] = {
@@ -1901,6 +1916,7 @@ struct ath10k *ath10k_core_create(size_t priv_size, struct device *dev,
 		ar->hw_values = &qca988x_values;
 		break;
 	case ATH10K_HW_QCA6174:
+	case ATH10K_HW_QCA9377:
 		ar->regs = &qca6174_regs;
 		ar->hw_values = &qca6174_values;
 		break;
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 0c8ea0226684..39966a05c1cc 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -84,6 +84,15 @@ enum qca6174_chip_id_rev {
 #define QCA99X0_HW_2_0_BOARD_DATA_FILE "board.bin"
 #define QCA99X0_HW_2_0_PATCH_LOAD_ADDR	0x1234
 
+/* QCA9377 1.0 definitions */
+#define QCA9377_HW_1_0_DEV_VERSION     0x05020001
+#define QCA9377_HW_1_0_CHIP_ID_REV     0x1
+#define QCA9377_HW_1_0_FW_DIR          ATH10K_FW_DIR "/QCA9377/hw1.0"
+#define QCA9377_HW_1_0_FW_FILE         "firmware.bin"
+#define QCA9377_HW_1_0_OTP_FILE        "otp.bin"
+#define QCA9377_HW_1_0_BOARD_DATA_FILE "board.bin"
+#define QCA9377_HW_1_0_PATCH_LOAD_ADDR	0x1234
+
 #define ATH10K_FW_API2_FILE		"firmware-2.bin"
 #define ATH10K_FW_API3_FILE		"firmware-3.bin"
 
@@ -177,6 +186,7 @@ enum ath10k_hw_rev {
 	ATH10K_HW_QCA988X,
 	ATH10K_HW_QCA6174,
 	ATH10K_HW_QCA99X0,
+	ATH10K_HW_QCA9377,
 };
 
 struct ath10k_hw_regs {
@@ -229,6 +239,7 @@ void ath10k_hw_fill_survey_time(struct ath10k *ar, struct survey_info *survey,
 #define QCA_REV_988X(ar) ((ar)->hw_rev == ATH10K_HW_QCA988X)
 #define QCA_REV_6174(ar) ((ar)->hw_rev == ATH10K_HW_QCA6174)
 #define QCA_REV_99X0(ar) ((ar)->hw_rev == ATH10K_HW_QCA99X0)
+#define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377)
 
 /* Known pecularities:
  *  - raw appears in nwifi decap, raw and nwifi appear in ethernet decap
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 4a6538508e9d..3fca200b986c 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -61,12 +61,14 @@ MODULE_PARM_DESC(reset_mode, "0: auto, 1: warm only (default: 0)");
 #define QCA6164_2_1_DEVICE_ID	(0x0041)
 #define QCA6174_2_1_DEVICE_ID	(0x003e)
 #define QCA99X0_2_0_DEVICE_ID	(0x0040)
+#define QCA9377_1_0_DEVICE_ID	(0x0042)
 
 static const struct pci_device_id ath10k_pci_id_table[] = {
 	{ PCI_VDEVICE(ATHEROS, QCA988X_2_0_DEVICE_ID) }, /* PCI-E QCA988X V2 */
 	{ PCI_VDEVICE(ATHEROS, QCA6164_2_1_DEVICE_ID) }, /* PCI-E QCA6164 V2.1 */
 	{ PCI_VDEVICE(ATHEROS, QCA6174_2_1_DEVICE_ID) }, /* PCI-E QCA6174 V2.1 */
 	{ PCI_VDEVICE(ATHEROS, QCA99X0_2_0_DEVICE_ID) }, /* PCI-E QCA99X0 V2 */
+	{ PCI_VDEVICE(ATHEROS, QCA9377_1_0_DEVICE_ID) }, /* PCI-E QCA9377 V1 */
 	{0}
 };
 
@@ -90,6 +92,7 @@ static const struct ath10k_pci_supp_chip ath10k_pci_supp_chips[] = {
 	{ QCA6174_2_1_DEVICE_ID, QCA6174_HW_3_2_CHIP_ID_REV },
 
 	{ QCA99X0_2_0_DEVICE_ID, QCA99X0_HW_2_0_CHIP_ID_REV },
+	{ QCA9377_1_0_DEVICE_ID, QCA9377_HW_1_0_CHIP_ID_REV },
 };
 
 static void ath10k_pci_buffer_cleanup(struct ath10k *ar);
@@ -827,6 +830,7 @@ static u32 ath10k_pci_targ_cpu_to_ce_addr(struct ath10k *ar, u32 addr)
 	switch (ar->hw_rev) {
 	case ATH10K_HW_QCA988X:
 	case ATH10K_HW_QCA6174:
+	case ATH10K_HW_QCA9377:
 		val = (ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
 					  CORE_CTRL_ADDRESS) &
 		       0x7ff) << 21;
@@ -1483,6 +1487,7 @@ static void ath10k_pci_irq_msi_fw_mask(struct ath10k *ar)
 	switch (ar->hw_rev) {
 	case ATH10K_HW_QCA988X:
 	case ATH10K_HW_QCA6174:
+	case ATH10K_HW_QCA9377:
 		val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
 					CORE_CTRL_ADDRESS);
 		val &= ~CORE_CTRL_PCIE_REG_31_MASK;
@@ -1504,6 +1509,7 @@ static void ath10k_pci_irq_msi_fw_unmask(struct ath10k *ar)
 	switch (ar->hw_rev) {
 	case ATH10K_HW_QCA988X:
 	case ATH10K_HW_QCA6174:
+	case ATH10K_HW_QCA9377:
 		val = ath10k_pci_read32(ar, SOC_CORE_BASE_ADDRESS +
 					CORE_CTRL_ADDRESS);
 		val |= CORE_CTRL_PCIE_REG_31_MASK;
@@ -1872,6 +1878,8 @@ static int ath10k_pci_get_num_banks(struct ath10k *ar)
 			return 9;
 		}
 		break;
+	case QCA9377_1_0_DEVICE_ID:
+		return 2;
 	}
 
 	ath10k_warn(ar, "unknown number of banks, assuming 1\n");
@@ -2332,6 +2340,8 @@ static int ath10k_pci_chip_reset(struct ath10k *ar)
 		return ath10k_pci_qca988x_chip_reset(ar);
 	else if (QCA_REV_6174(ar))
 		return ath10k_pci_qca6174_chip_reset(ar);
+	else if (QCA_REV_9377(ar))
+		return ath10k_pci_qca6174_chip_reset(ar);
 	else if (QCA_REV_99X0(ar))
 		return ath10k_pci_qca99x0_chip_reset(ar);
 	else
@@ -2964,6 +2974,10 @@ static int ath10k_pci_probe(struct pci_dev *pdev,
 		hw_rev = ATH10K_HW_QCA99X0;
 		pci_ps = false;
 		break;
+	case QCA9377_1_0_DEVICE_ID:
+		hw_rev = ATH10K_HW_QCA9377;
+		pci_ps = true;
+		break;
 	default:
 		WARN_ON(1);
 		return -ENOTSUPP;
@@ -3165,3 +3179,7 @@ MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_FW_API4_FILE);
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_FW_API5_FILE);
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" QCA6174_HW_3_0_BOARD_DATA_FILE);
 MODULE_FIRMWARE(QCA6174_HW_3_0_FW_DIR "/" ATH10K_BOARD_API2_FILE);
+
+/* QCA9377 1.0 firmware files */
+MODULE_FIRMWARE(QCA9377_HW_1_0_FW_DIR "/" ATH10K_FW_API5_FILE);
+MODULE_FIRMWARE(QCA9377_HW_1_0_FW_DIR "/" QCA9377_HW_1_0_BOARD_DATA_FILE);
diff --git a/drivers/net/wireless/ath/ath10k/targaddrs.h b/drivers/net/wireless/ath/ath10k/targaddrs.h
index 768bef629099..05a421bc322a 100644
--- a/drivers/net/wireless/ath/ath10k/targaddrs.h
+++ b/drivers/net/wireless/ath/ath10k/targaddrs.h
@@ -450,6 +450,9 @@ Fw Mode/SubMode Mask
 #define QCA6174_BOARD_DATA_SZ     8192
 #define QCA6174_BOARD_EXT_DATA_SZ 0
 
+#define QCA9377_BOARD_DATA_SZ     QCA6174_BOARD_DATA_SZ
+#define QCA9377_BOARD_EXT_DATA_SZ 0
+
 #define QCA99X0_BOARD_DATA_SZ	  12288
 #define QCA99X0_BOARD_EXT_DATA_SZ 0
 
-- 
cgit v1.2.3


From 12551ced30bb4658496ba76b7998dc6930b45722 Mon Sep 17 00:00:00 2001
From: Bartosz Markowski <bartosz.markowski@tieto.com>
Date: Thu, 5 Nov 2015 09:50:40 +0100
Subject: ath10k: fix the currently supported QCA9377 target version name

When introducing the original QCA9377 support, the chip target
version was wrongly picked. The chip advertising itself with
bmi target value equal to 0x05020001 is in fact a 1.1 revision.
I realized this once I got a real 1.1 hw to play with.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 4 ++--
 drivers/net/wireless/ath/ath10k/hw.h   | 8 ++++++--
 drivers/net/wireless/ath/ath10k/pci.c  | 2 +-
 3 files changed, 9 insertions(+), 5 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index aa9bd92ac4ed..c8f6ca284b9d 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -138,8 +138,8 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		},
 	},
 	{
-		.id = QCA9377_HW_1_0_DEV_VERSION,
-		.name = "qca9377 hw1.0",
+		.id = QCA9377_HW_1_1_DEV_VERSION,
+		.name = "qca9377 hw1.1",
 		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
 		.uart_pin = 7,
 		.otp_exe_param = 0,
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 39966a05c1cc..01bf2244f54c 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -42,6 +42,8 @@
 #define QCA6174_HW_3_0_VERSION		0x05020000
 #define QCA6174_HW_3_2_VERSION		0x05030000
 
+#define QCA9377_HW_1_1_DEV_VERSION	0x05020001
+
 enum qca6174_pci_rev {
 	QCA6174_PCI_REV_1_1 = 0x11,
 	QCA6174_PCI_REV_1_3 = 0x13,
@@ -60,6 +62,10 @@ enum qca6174_chip_id_rev {
 	QCA6174_HW_3_2_CHIP_ID_REV = 10,
 };
 
+enum qca9377_chip_id_rev {
+	QCA9377_HW_1_1_CHIP_ID_REV = 0x1,
+};
+
 #define QCA6174_HW_2_1_FW_DIR		"ath10k/QCA6174/hw2.1"
 #define QCA6174_HW_2_1_FW_FILE		"firmware.bin"
 #define QCA6174_HW_2_1_OTP_FILE		"otp.bin"
@@ -85,8 +91,6 @@ enum qca6174_chip_id_rev {
 #define QCA99X0_HW_2_0_PATCH_LOAD_ADDR	0x1234
 
 /* QCA9377 1.0 definitions */
-#define QCA9377_HW_1_0_DEV_VERSION     0x05020001
-#define QCA9377_HW_1_0_CHIP_ID_REV     0x1
 #define QCA9377_HW_1_0_FW_DIR          ATH10K_FW_DIR "/QCA9377/hw1.0"
 #define QCA9377_HW_1_0_FW_FILE         "firmware.bin"
 #define QCA9377_HW_1_0_OTP_FILE        "otp.bin"
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 3fca200b986c..c444b43f183d 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -92,7 +92,7 @@ static const struct ath10k_pci_supp_chip ath10k_pci_supp_chips[] = {
 	{ QCA6174_2_1_DEVICE_ID, QCA6174_HW_3_2_CHIP_ID_REV },
 
 	{ QCA99X0_2_0_DEVICE_ID, QCA99X0_HW_2_0_CHIP_ID_REV },
-	{ QCA9377_1_0_DEVICE_ID, QCA9377_HW_1_0_CHIP_ID_REV },
+	{ QCA9377_1_0_DEVICE_ID, QCA9377_HW_1_1_CHIP_ID_REV },
 };
 
 static void ath10k_pci_buffer_cleanup(struct ath10k *ar);
-- 
cgit v1.2.3


From 6cf213958299803c1166e63c1805a8b8cd135be5 Mon Sep 17 00:00:00 2001
From: Bartosz Markowski <bartosz.markowski@tieto.com>
Date: Thu, 5 Nov 2015 09:50:41 +0100
Subject: ath10k: update missing hw_params of QCA9377 hw1.1

The uart_pin was incorrectly configured for QCA9377
and the recently added hw_params were omitted.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index c8f6ca284b9d..a30d41559134 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -141,8 +141,10 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 		.id = QCA9377_HW_1_1_DEV_VERSION,
 		.name = "qca9377 hw1.1",
 		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
-		.uart_pin = 7,
+		.uart_pin = 6,
 		.otp_exe_param = 0,
+		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
 		.fw = {
 			.dir = QCA9377_HW_1_0_FW_DIR,
 			.fw = QCA9377_HW_1_0_FW_FILE,
-- 
cgit v1.2.3


From 079a0490e207c5a88e4b40cefcc331f4bce562f4 Mon Sep 17 00:00:00 2001
From: Bartosz Markowski <bartosz.markowski@tieto.com>
Date: Thu, 5 Nov 2015 09:50:42 +0100
Subject: ath10k: introduce dev_id to hw_params

A follow up patch introducing a QCA9377 hw1.0 support will need
this device identification helper for an explicit distinction of
HWs, as apparently both QCA6174 hw3.0 and QCA9377 share the same BMI
target version (0x0502000x). For the QCA9377 hw1.1 previously
added we were just lucky we did not overlap with the same chip_id_rev.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 27 ++++++++++++++++++++++++++-
 drivers/net/wireless/ath/ath10k/core.h |  1 +
 drivers/net/wireless/ath/ath10k/hw.h   |  6 ++++++
 drivers/net/wireless/ath/ath10k/pci.c  |  6 ------
 4 files changed, 33 insertions(+), 7 deletions(-)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index a30d41559134..b80b8f372354 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -51,6 +51,7 @@ MODULE_PARM_DESC(rawmode, "Use raw 802.11 frame datapath");
 static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	{
 		.id = QCA988X_HW_2_0_VERSION,
+		.dev_id = QCA988X_2_0_DEVICE_ID,
 		.name = "qca988x hw2.0",
 		.patch_load_addr = QCA988X_HW_2_0_PATCH_LOAD_ADDR,
 		.uart_pin = 7,
@@ -69,6 +70,25 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	},
 	{
 		.id = QCA6174_HW_2_1_VERSION,
+		.dev_id = QCA6164_2_1_DEVICE_ID,
+		.name = "qca6164 hw2.1",
+		.patch_load_addr = QCA6174_HW_2_1_PATCH_LOAD_ADDR,
+		.uart_pin = 6,
+		.otp_exe_param = 0,
+		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
+		.fw = {
+			.dir = QCA6174_HW_2_1_FW_DIR,
+			.fw = QCA6174_HW_2_1_FW_FILE,
+			.otp = QCA6174_HW_2_1_OTP_FILE,
+			.board = QCA6174_HW_2_1_BOARD_DATA_FILE,
+			.board_size = QCA6174_BOARD_DATA_SZ,
+			.board_ext_size = QCA6174_BOARD_EXT_DATA_SZ,
+		},
+	},
+	{
+		.id = QCA6174_HW_2_1_VERSION,
+		.dev_id = QCA6174_2_1_DEVICE_ID,
 		.name = "qca6174 hw2.1",
 		.patch_load_addr = QCA6174_HW_2_1_PATCH_LOAD_ADDR,
 		.uart_pin = 6,
@@ -86,6 +106,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	},
 	{
 		.id = QCA6174_HW_3_0_VERSION,
+		.dev_id = QCA6174_2_1_DEVICE_ID,
 		.name = "qca6174 hw3.0",
 		.patch_load_addr = QCA6174_HW_3_0_PATCH_LOAD_ADDR,
 		.uart_pin = 6,
@@ -103,6 +124,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	},
 	{
 		.id = QCA6174_HW_3_2_VERSION,
+		.dev_id = QCA6174_2_1_DEVICE_ID,
 		.name = "qca6174 hw3.2",
 		.patch_load_addr = QCA6174_HW_3_0_PATCH_LOAD_ADDR,
 		.uart_pin = 6,
@@ -121,6 +143,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	},
 	{
 		.id = QCA99X0_HW_2_0_DEV_VERSION,
+		.dev_id = QCA99X0_2_0_DEVICE_ID,
 		.name = "qca99x0 hw2.0",
 		.patch_load_addr = QCA99X0_HW_2_0_PATCH_LOAD_ADDR,
 		.uart_pin = 7,
@@ -139,6 +162,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 	},
 	{
 		.id = QCA9377_HW_1_1_DEV_VERSION,
+		.dev_id = QCA9377_1_0_DEVICE_ID,
 		.name = "qca9377 hw1.1",
 		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
 		.uart_pin = 6,
@@ -1265,7 +1289,8 @@ static int ath10k_init_hw_params(struct ath10k *ar)
 	for (i = 0; i < ARRAY_SIZE(ath10k_hw_params_list); i++) {
 		hw_params = &ath10k_hw_params_list[i];
 
-		if (hw_params->id == ar->target_version)
+		if (hw_params->id == ar->target_version &&
+		    hw_params->dev_id == ar->dev_id)
 			break;
 	}
 
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 4a2301589902..622d3816eaf4 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -636,6 +636,7 @@ struct ath10k {
 
 	struct ath10k_hw_params {
 		u32 id;
+		u16 dev_id;
 		const char *name;
 		u32 patch_load_addr;
 		int uart_pin;
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 01bf2244f54c..13aacbdc98e6 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -22,6 +22,12 @@
 
 #define ATH10K_FW_DIR			"ath10k"
 
+#define QCA988X_2_0_DEVICE_ID   (0x003c)
+#define QCA6164_2_1_DEVICE_ID   (0x0041)
+#define QCA6174_2_1_DEVICE_ID   (0x003e)
+#define QCA99X0_2_0_DEVICE_ID   (0x0040)
+#define QCA9377_1_0_DEVICE_ID   (0x0042)
+
 /* QCA988X 1.0 definitions (unsupported) */
 #define QCA988X_HW_1_0_CHIP_ID_REV	0x0
 
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index c444b43f183d..14dce2a1b39f 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -57,12 +57,6 @@ MODULE_PARM_DESC(reset_mode, "0: auto, 1: warm only (default: 0)");
 #define ATH10K_PCI_TARGET_WAIT 3000
 #define ATH10K_PCI_NUM_WARM_RESET_ATTEMPTS 3
 
-#define QCA988X_2_0_DEVICE_ID	(0x003c)
-#define QCA6164_2_1_DEVICE_ID	(0x0041)
-#define QCA6174_2_1_DEVICE_ID	(0x003e)
-#define QCA99X0_2_0_DEVICE_ID	(0x0040)
-#define QCA9377_1_0_DEVICE_ID	(0x0042)
-
 static const struct pci_device_id ath10k_pci_id_table[] = {
 	{ PCI_VDEVICE(ATHEROS, QCA988X_2_0_DEVICE_ID) }, /* PCI-E QCA988X V2 */
 	{ PCI_VDEVICE(ATHEROS, QCA6164_2_1_DEVICE_ID) }, /* PCI-E QCA6164 V2.1 */
-- 
cgit v1.2.3


From 034074f3a889b69325326e612b7b37f3492a65ad Mon Sep 17 00:00:00 2001
From: Bartosz Markowski <bartosz.markowski@tieto.com>
Date: Thu, 5 Nov 2015 09:50:43 +0100
Subject: ath10k: add QCA9377 hw1.0 support

Add new BMI target version and chip id revision. Register it
on supported chips list.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 18 ++++++++++++++++++
 drivers/net/wireless/ath/ath10k/hw.h   |  3 +++
 drivers/net/wireless/ath/ath10k/pci.c  |  2 ++
 3 files changed, 23 insertions(+)

(limited to 'drivers/net/wireless/ath/ath10k/core.c')

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b80b8f372354..0947cc271e69 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -160,6 +160,24 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
 			.board_ext_size = QCA99X0_BOARD_EXT_DATA_SZ,
 		},
 	},
+	{
+		.id = QCA9377_HW_1_0_DEV_VERSION,
+		.dev_id = QCA9377_1_0_DEVICE_ID,
+		.name = "qca9377 hw1.0",
+		.patch_load_addr = QCA9377_HW_1_0_PATCH_LOAD_ADDR,
+		.uart_pin = 6,
+		.otp_exe_param = 0,
+		.channel_counters_freq_hz = 88000,
+		.max_probe_resp_desc_thres = 0,
+		.fw = {
+			.dir = QCA9377_HW_1_0_FW_DIR,
+			.fw = QCA9377_HW_1_0_FW_FILE,
+			.otp = QCA9377_HW_1_0_OTP_FILE,
+			.board = QCA9377_HW_1_0_BOARD_DATA_FILE,
+			.board_size = QCA9377_BOARD_DATA_SZ,
+			.board_ext_size = QCA9377_BOARD_EXT_DATA_SZ,
+		},
+	},
 	{
 		.id = QCA9377_HW_1_1_DEV_VERSION,
 		.dev_id = QCA9377_1_0_DEVICE_ID,
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 13aacbdc98e6..713c2bcea178 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -48,6 +48,8 @@
 #define QCA6174_HW_3_0_VERSION		0x05020000
 #define QCA6174_HW_3_2_VERSION		0x05030000
 
+/* QCA9377 target BMI version signatures */
+#define QCA9377_HW_1_0_DEV_VERSION	0x05020000
 #define QCA9377_HW_1_1_DEV_VERSION	0x05020001
 
 enum qca6174_pci_rev {
@@ -69,6 +71,7 @@ enum qca6174_chip_id_rev {
 };
 
 enum qca9377_chip_id_rev {
+	QCA9377_HW_1_0_CHIP_ID_REV = 0x0,
 	QCA9377_HW_1_1_CHIP_ID_REV = 0x1,
 };
 
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 14dce2a1b39f..679a3ebb34af 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -86,6 +86,8 @@ static const struct ath10k_pci_supp_chip ath10k_pci_supp_chips[] = {
 	{ QCA6174_2_1_DEVICE_ID, QCA6174_HW_3_2_CHIP_ID_REV },
 
 	{ QCA99X0_2_0_DEVICE_ID, QCA99X0_HW_2_0_CHIP_ID_REV },
+
+	{ QCA9377_1_0_DEVICE_ID, QCA9377_HW_1_0_CHIP_ID_REV },
 	{ QCA9377_1_0_DEVICE_ID, QCA9377_HW_1_1_CHIP_ID_REV },
 };
 
-- 
cgit v1.2.3