path: root/drivers/ata/pata_pdc202xx_old.c
AgeCommit message (Collapse)Author
2010-10-21pata_pdc202xx_old: implement sff_irq_check() methodSergei Shtylyov
Signed-off-by: Sergei Shtylyov <> Signed-off-by: Jeff Garzik <>
2010-05-25libata-sff: separate out BMDMA initTejun Heo
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one() from their SFF counterparts. SFF ones no longer try to initialize BMDMA or set PCI master. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2010-05-19libata-sff: clean up BMDMA initializationTejun Heo
When BMDMA initialization failed or BMDMA was not available for whatever reason, bmdma_addr was left at zero and used as an indication that BMDMA shouldn't be used. This leads to the following problems. p1. For BMDMA drivers which don't use traditional BMDMA register, ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those drivers either have to inherit from ata_sff_port_ops or clear ->mode_filter explicitly. p2. non-BMDMA drivers call into BMDMA PRD table allocation. It doesn't actually allocate PRD table if bmdma_addr is not initialized but is still confusing. p3. For BMDMA drivers which don't use traditional BMDMA register, some methods might not be invoked as expected (e.g. bmdma_stop from ata_sff_post_internal_cmd()). p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops worrying libata core might call into one of them. These problems are caused by the muddy line between SFF and BMDMA and the assumption that all BMDMA controllers initialize bmdma_addr. This patch fixes p1 and p2 by removing the bmdma_addr assumption and moving prd allocation to BMDMA port start. Later patches will fix the remaining issues. This patch improves BMDMA initialization such that * When BMDMA register initialization fails, falls back to PIO instead of failing. ata_pci_bmdma_init() never fails now. * When ata_pci_bmdma_init() falls back to PIO, it clears ap->mwdma_mask and udma_mask instead of depending on ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter() unnecessary thus resolving p1. * ata_port_start() which actually is BMDMA specific is moved to ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start() are killed. * ata_sff_port_start32() is moved and renamed to ata_bmdma_port_start32(). Drivers which no longer call into PRD table allocation are... pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all drivers which inherit from ata_sff_port_ops. pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD but is a BMDMA controller and doesn't have custom port_start like other such controllers. Note that with the previous patch which makes all and only BMDMA drivers inherit from ata_bmdma_port_ops, this change doesn't break drivers which need PRD table. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2010-03-01libata: Pass host flags into the pci helperAlan Cox
This allows parallel scan and the like to be set without having to stop using the existing full helper functions. This patch merely adds the argument and fixes up the callers. It doesn't undo the special cases already in the tree or add any new parallel callers. Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2010-03-01pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsetsBartlomiej Zolnierkiewicz
PDC2026x chipsets need the same treatment as PDC20246 one. This is completely untested but will hopefully fix UDMA issues that people have been reporting against pata_pdc202xx_old for the last couple of years. Signed-off-by: Bartlomiej Zolnierkiewicz <> Signed-off-by: Jeff Garzik <>
2010-03-01pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cardsBartlomiej Zolnierkiewicz
On Monday 04 January 2010 02:30:24 pm Russell King wrote: > Found the problem - getting rid of the read of the alt status register > after the command has been written fixes the UDMA CRC errors on write: > > @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct > ata_taskfile *tf) > DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); > > iowrite8(tf->command, ap->ioaddr.command_addr); > - ata_sff_pause(ap); > + ndelay(400); > +// ata_sff_pause(ap); > } > EXPORT_SYMBOL_GPL(ata_sff_exec_command); > > > This rather makes sense. The PDC20247 handles the UDMA part of the > protocol. It has no way to tell the PDC20246 to wait while it suspends > UDMA, so that a normal register access can take place - the 246 ploughs > on with the register access without any regard to the state of the 247. > > If the drive immediately starts the UDMA protocol after a write to the > command register (as it probably will for the DMA WRITE command), then > we'll be accessing the taskfile in the middle of the UDMA setup, which > can't be good. It's certainly a violation of the ATA specs. Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets. Debugged-by: Russell King <> Signed-off-by: Bartlomiej Zolnierkiewicz <> Signed-off-by: Jeff Garzik <>
2009-05-11pata_pdc202xx_old: fix UDMA33 handlingBartlomiej Zolnierkiewicz
The original driver doesn't use 66 MHz clock for UDMA33. [ The alternative solution would be to adjust UDMA33 timings for 66 MHz clock but I think that it is safer to stick with old & tested behavior for now. ] Signed-off-by: Bartlomiej Zolnierkiewicz <> Signed-off-by: Jeff Garzik <>
2009-03-24[libata] convert drivers to use ata.h mode mask definesErik Inge Bolsø
No functional changes in this patch. Signed-off-by: Erik Inge Bolsø <> Signed-off-by: Jeff Garzik <>
2008-10-27ata: Switch all my stuff to a common addressAlan Cox
Signed-off-by: Jeff Garzik <>
2008-04-17libata: rename SFF functionsTejun Heo
SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <>
2008-04-17libata: stop overloading port_info->private_dataTejun Heo
port_info->private_data is currently used for two purposes - to record private data about the port_info or to specify host->private_data to use when allocating ata_host. This overloading is confusing and counter-intuitive in that port_info->private_data becomes host->private_data instead of port->private_data. In addition, port_info and host don't correspond to each other 1-to-1. Currently, the first non-NULL port_info->private_data is used. This patch makes port_info->private_data just be what it is - private_data for the port_info where LLD can jot down extra info. libata no longer sets host->private_data to the first non-NULL port_info->private_data, @host_priv argument is added to ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use this argument to pass in pointer to host private data. LLDs which don't should use init-register model anyway and can initialize host->private_data directly. Adding @host_priv instead of using init-register model for LLDs which use ata_pci_init_one() is suggested by Alan Cox. Signed-off-by: Tejun Heo <> Cc: Alan Cox <>
2008-04-17libata: make ata_pci_init_one() not use ops->irq_handler and pi->shtTejun Heo
ata_pci_init_one() is the only function which uses ops->irq_handler and pi->sht. Other initialization functions take the same information as arguments. This causes confusion and duplicate unused entries in structures. Make ata_pci_init_one() take sht as an argument and use ata_interrupt implicitly. All current users use ata_interrupt and if different irq handler is necessary open coding ata_pci_init_one() using ata_prepare_sff_host() and ata_activate_sff_host can be done under ten lines including error handling and driver which requires custom interrupt handler is likely to require custom initialization anyway. As ata_pci_init_one() was the last user of ops->irq_handler, this patch also kills the field. Signed-off-by: Tejun Heo <>
2008-04-17libata: implement and use ops inheritanceTejun Heo
libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <>
2008-04-17libata: implement and use SHT initializersTejun Heo
libata lets low level drivers build scsi_host_template and register it to the SCSI layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This patch implements SHT initializers which can be used to initialize all the boilerplate entries in a sht. Three variants of them are implemented - BASE, BMDMA and NCQ - for different types of drivers. Note that entries can be overriden by putting individual initializers after the helper macro. All sht tables are identical before and after this patch. Signed-off-by: Tejun Heo <>
2008-01-23libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*Tejun Heo
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to ATAPI_PROT_* and make them consistent with ATA counterpart. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2008-01-19pata_pdc202xx_old: Fix crashes with ATAPIAlan Cox
The PDC202xx older devices do not support ATAPI DMA via the usual interfaces. What documentation I have isn't sufficient to support DMA and it isn't clear if the Windows drivers do this or it is possible at all. (Neither do the drivers/ide old drivers) So turn it ATAPI DMA off, these are disk optimised controllers. Signed-off-by: Alan Cox <> Signed-off-by: Linus Torvalds <>
2008-01-10pata_pdc202xx_old: Further fixupsAlan Cox
Turns out distros always enabled burst mode and it is pretty essential so do the same. Also sort out the post DMA mode restore properly. My 20263 card now seems happy but needs some four drive tests done yet (when I've persuaded the kernel not to hang in the edd boot code if I plug them in ..) Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-10-29[libata] fix 'if(' and similar areas that lack whitespaceJeff Garzik
Signed-off-by: Jeff Garzik <>
2007-10-12pata_pdc202xx_old MWDMA fixes, and notesAlan Cox
I've been doing an audit of this driver to try and find out why we have problems with some Clevo boxes that use it. Didn't get anywhere other than to discover all the bug reporters I have use vmware, which may or may not be chance. In the process however I did find out our MWDMA2 performance was a bit low and code review showed the MWDMA0/2 timings are reversed due to a thinko in the table ordering Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-10-12libata: Switch most of the remaining SFF drivers to ata_sff_port_startAlan Cox
This avoids allocating DMA buffers if not needed but at the moment is mostly just a neatness item. Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-10-12[libata] Remove ->port_disable() hookJeff Garzik
It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <>
2007-10-12[libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik
* ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <>
2007-07-09[libata] PATA drivers: remove ATA_FLAG_SRSTJeff Garzik
This flag only has meaning in old-EH drivers, and these drivers have already been converted to the new EH. Remove. Signed-off-by: Jeff Garzik <>
2007-07-03pata_pdc202xx_old: Correct cable detect logicAlan Cox
We got it backwards and now the other detects are fixed it shows up Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-05-11libata: clean up SFF init messTejun Heo
The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2007-05-11libata: reimplement suspend/resume support using sdev->manage_start_stopTejun Heo
Reimplement suspend/resume support using sdev->manage_start_stop. * Device suspend/resume is now SCSI layer's responsibility and the code is simplified a lot. * DPM is dropped. This also simplifies code a lot. Suspend/resume status is port-wide now. * ata_scsi_device_suspend/resume() and ata_dev_ready() removed. * Resume now has to wait for disk to spin up before proceeding. I couldn't find easy way out as libata is in EH waiting for the disk to be ready and sd is waiting for EH to complete to issue START_STOP. * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config(). This fixes spindown on shutdown and suspend-to-disk. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2007-04-28[libata] Update several PATA drivers for new ->cable_detect hookJeff Garzik
All patches authored and signed-off-by Alan Cox, sent on Mar 7, 2007. I merely combined them all into a single patch. Signed-off-by: Jeff Garzik <>
2007-04-28libata: dev_config does not need ap and adev passingAlan
It used to be impossible to get from ata_device to ata_port but that is no longer true. Various methods have been cleaned up over time but dev_config still takes both and most users don't need both anyway. Tidy this one up Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-03-28pata_pdc202xx_old: LBA48 bugAlan Cox
In LBA48 mode we have to help the controller to get anything to work. The chip provides a register giving word counts meant for ATAPI use which we can use. However we need to load the count in words not bytes.. Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2007-03-06pata_pdc202xx_old: fix data corruption and other problemsBartlomiej Zolnierkiewicz
Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}() They were broken for all configurations except one (master device on primary channel, no other devices) and as a result device settings + PIO/DMA timings were being programmed into the wrong PCI registers. This could result in a large variety of problems including data corruption, hangs etc. (depending on devices used and your luck :-). ap->port_no ap->devno used PCI registers correct PCI registers 0 0 0x60-0x62 0x60-0x62 0 1 0x62-0x64 0x64-0x66 1 0 0x64-0x66 0x68-0x6a 1 1 0x66-0x68 0x6c-0x6e Also forward port recent fixes from drivers/ide pdc202xx_old driver: * fix XFER_MW_DMA0 timings (they were overclocked, use the official ones) * fix bitmasks for clearing bits of register B: - when programming DMA mode bit 0x10 of register B was cleared which resulted in overclocked PIO timing setting (iff PIO0 was used) - when programming PIO mode bits 0x18 weren't cleared so suboptimal timings were used for PIO1-4 if PIO0 was previously set (bit 0x10) and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08) and finally bump driver version. Signed-off-by: Bartlomiej Zolnierkiewicz <> Signed-off-by: Jeff Garzik <>
2007-03-02libata: add missing CONFIG_PM in LLDsTejun Heo
Add missing #ifdef CONFIG_PM conditionals around all PM related parts in libata LLDs. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2007-02-26[libata] bump versionsJeff Garzik
Bump versions based on changes submitted during 2.6.21 merge window. Signed-off-by: Jeff Garzik <>
2007-02-09libata: add another IRQ calls (libata drivers)Akira Iguchi
This patch is against each libata driver. Two IRQ calls are added in ata_port_operations. - irq_on() is used to enable interrupts. - irq_ack() is used to acknowledge a device interrupt. In most drivers, ata_irq_on() and ata_irq_ack() are used for irq_on and irq_ack respectively. In some drivers (ex: ahci, sata_sil24) which cannot use them as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used. Signed-off-by: Kou Ishizaki <> Signed-off-by: Akira Iguchi <> Signed-off-by: Jeff Garzik <>
2007-02-09libata: convert to iomapTejun Heo
Convert libata core layer and LLDs to use iomap. * managed iomap is used. Pointer to pcim_iomap_table() is cached at host->iomap and used through out LLDs. This basically replaces host->mmio_base. * if possible, pcim_iomap_regions() is used Most iomap operation conversions are taken from Jeff Garzik <>'s iomap branch. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2007-02-09libata: update libata LLDs to use devresTejun Heo
Update libata LLDs to use devres. Core layer is already converted to support managed LLDs. This patch simplifies initialization and fixes many resource related bugs in init failure and detach path. For example, all converted drivers now handle ata_device_add() failure gracefully without excessive resource rollback code. As most resources are released automatically on driver detach, many drivers don't need or can do with much simpler ->{port|host}_stop(). In general, stop callbacks are need iff port or host needs to be given commands to shut it down. Note that freezing is enough in many cases and ports are automatically frozen before being detached. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2007-02-09libata: kill qc->nsect and cursectTejun Heo
libata used two separate sets of variables to record request size and current offset for ATA and ATAPI. This is confusing and fragile. This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and kills them. Also, ata_pio_sector() is updated to use bytes for qc->cursg_ofs instead of sectors. The field used to be used in bytes for ATAPI and in sectors for ATA. Signed-off-by: Tejun Heo <> Signed-off-by: Jeff Garzik <>
2006-12-03[PATCH] libata: kill unnecessary sht->max_sectors initializationsTejun Heo
sht->max_sectors is overrided unconditionally in ->slave_configure. There's no reason to set it to any value. Signed-off-by: Tejun Heo <>
2006-12-01[PATCH] pata : more drivers that need only standard suspend and resumeAlan
Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2006-12-01[PATCH] pdc202xx_old: Fix name clashes with PA-RISCAlan Cox
pdc_* functions are part of the global namespace for the PDC on PA-RISC systems and this means our choice of pdc_ causes collisions between the PDC globals and our static functions. Rename them to pdc202xx where they are for both 2024x and 2026x. Signed-off-by: Alan Cox <> Signed-off-by: Jeff Garzik <>
2006-11-29[PATCH] libata: add missing sht->slave_destroyTejun Heo
Many LLDs are missing sht->slave_destroy. The method is mandatory to support device warm unplugging (echo 1 > /sys/.../delete). Without it, libata might access released scsi device. Signed-off-by: Tejun Heo <>
2006-09-28[libata] PCI ID table cleanup in various driversJeff Garzik
* Use PCI_VDEVICE() macro * const-ify pci_device_id table * standardize list terminator as "{ }" * convert spaces to tab in pci_driver struct (Alan-ism) * various minor whitespace cleanups Signed-off-by: Jeff Garzik <>
2006-08-31[libata #pata-drivers] Trim trailing whitespace.Jeff Garzik
2006-08-29[libata] Add a bunch of PATA drivers.Jeff Garzik
The vast majority of drivers and changes are from Alan Cox. Albert Lee contributed and maintains pata_pdc2027x. Adrian Bunk, Andrew Morton, and Tejun Heo contributed various minor fixes and updates. Signed-off-by: Jeff Garzik <>