summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorMauro Carvalho Chehab <mchehab@s-opensource.com>2016-07-18 13:32:53 -0300
committerMauro Carvalho Chehab <mchehab@s-opensource.com>2016-07-18 13:32:53 -0300
commitf8eb496f4cadb392f03f329bf586a8134174a502 (patch)
tree5615340c4e3cb24b98153fc89dddc4760e38aa3f
parentd9b8a3f099d9a8b76393da271278d3bd88c0e9ed (diff)
[media] cx2341x.rst: add contents of fw-dma.txt
Add the contents of fw-dma.txt, converted to ReST, and drop the old file. Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-rw-r--r--Documentation/media/v4l-drivers/cx2341x.rst99
-rw-r--r--Documentation/video4linux/cx2341x/fw-dma.txt96
2 files changed, 99 insertions, 96 deletions
diff --git a/Documentation/media/v4l-drivers/cx2341x.rst b/Documentation/media/v4l-drivers/cx2341x.rst
index cbfa14eccd76..ca2f15c5b8f7 100644
--- a/Documentation/media/v4l-drivers/cx2341x.rst
+++ b/Documentation/media/v4l-drivers/cx2341x.rst
@@ -2703,3 +2703,102 @@ out what values are bad when it hangs.
--------------------------------------------------------------------------------
+The cx231xx DMA engine
+----------------------
+
+
+This page describes the structures and procedures used by the cx2341x DMA
+engine.
+
+Introduction
+~~~~~~~~~~~~
+
+The cx2341x PCI interface is busmaster capable. This means it has a DMA
+engine to efficiently transfer large volumes of data between the card and main
+memory without requiring help from a CPU. Like most hardware, it must operate
+on contiguous physical memory. This is difficult to come by in large quantities
+on virtual memory machines.
+
+Therefore, it also supports a technique called "scatter-gather". The card can
+transfer multiple buffers in one operation. Instead of allocating one large
+contiguous buffer, the driver can allocate several smaller buffers.
+
+In practice, I've seen the average transfer to be roughly 80K, but transfers
+above 128K were not uncommon, particularly at startup. The 128K figure is
+important, because that is the largest block that the kernel can normally
+allocate. Even still, 128K blocks are hard to come by, so the driver writer is
+urged to choose a smaller block size and learn the scatter-gather technique.
+
+Mailbox #10 is reserved for DMA transfer information.
+
+Note: the hardware expects little-endian data ('intel format').
+
+Flow
+~~~~
+
+This section describes, in general, the order of events when handling DMA
+transfers. Detailed information follows this section.
+
+- The card raises the Encoder interrupt.
+- The driver reads the transfer type, offset and size from Mailbox #10.
+- The driver constructs the scatter-gather array from enough free dma buffers
+ to cover the size.
+- The driver schedules the DMA transfer via the ScheduleDMAtoHost API call.
+- The card raises the DMA Complete interrupt.
+- The driver checks the DMA status register for any errors.
+- The driver post-processes the newly transferred buffers.
+
+NOTE! It is possible that the Encoder and DMA Complete interrupts get raised
+simultaneously. (End of the last, start of the next, etc.)
+
+Mailbox #10
+~~~~~~~~~~~
+
+The Flags, Command, Return Value and Timeout fields are ignored.
+
+- Name: Mailbox #10
+- Results[0]: Type: 0: MPEG.
+- Results[1]: Offset: The position relative to the card's memory space.
+- Results[2]: Size: The exact number of bytes to transfer.
+
+My speculation is that since the StartCapture API has a capture type of "RAW"
+available, that the type field will have other values that correspond to YUV
+and PCM data.
+
+Scatter-Gather Array
+~~~~~~~~~~~~~~~~~~~~
+
+The scatter-gather array is a contiguously allocated block of memory that
+tells the card the source and destination of each data-block to transfer.
+Card "addresses" are derived from the offset supplied by Mailbox #10. Host
+addresses are the physical memory location of the target DMA buffer.
+
+Each S-G array element is a struct of three 32-bit words. The first word is
+the source address, the second is the destination address. Both take up the
+entire 32 bits. The lowest 18 bits of the third word is the transfer byte
+count. The high-bit of the third word is the "last" flag. The last-flag tells
+the card to raise the DMA_DONE interrupt. From hard personal experience, if
+you forget to set this bit, the card will still "work" but the stream will
+most likely get corrupted.
+
+The transfer count must be a multiple of 256. Therefore, the driver will need
+to track how much data in the target buffer is valid and deal with it
+accordingly.
+
+Array Element:
+
+- 32-bit Source Address
+- 32-bit Destination Address
+- 14-bit reserved (high bit is the last flag)
+- 18-bit byte count
+
+DMA Transfer Status
+~~~~~~~~~~~~~~~~~~~
+
+Register 0x0004 holds the DMA Transfer Status:
+
+- bit 0: read completed
+- bit 1: write completed
+- bit 2: DMA read error
+- bit 3: DMA write error
+- bit 4: Scatter-Gather array error
diff --git a/Documentation/video4linux/cx2341x/fw-dma.txt b/Documentation/video4linux/cx2341x/fw-dma.txt
deleted file mode 100644
index be52b6fd1e9a..000000000000
--- a/Documentation/video4linux/cx2341x/fw-dma.txt
+++ /dev/null
@@ -1,96 +0,0 @@
-This page describes the structures and procedures used by the cx2341x DMA
-engine.
-
-Introduction
-============
-
-The cx2341x PCI interface is busmaster capable. This means it has a DMA
-engine to efficiently transfer large volumes of data between the card and main
-memory without requiring help from a CPU. Like most hardware, it must operate
-on contiguous physical memory. This is difficult to come by in large quantities
-on virtual memory machines.
-
-Therefore, it also supports a technique called "scatter-gather". The card can
-transfer multiple buffers in one operation. Instead of allocating one large
-contiguous buffer, the driver can allocate several smaller buffers.
-
-In practice, I've seen the average transfer to be roughly 80K, but transfers
-above 128K were not uncommon, particularly at startup. The 128K figure is
-important, because that is the largest block that the kernel can normally
-allocate. Even still, 128K blocks are hard to come by, so the driver writer is
-urged to choose a smaller block size and learn the scatter-gather technique.
-
-Mailbox #10 is reserved for DMA transfer information.
-
-Note: the hardware expects little-endian data ('intel format').
-
-Flow
-====
-
-This section describes, in general, the order of events when handling DMA
-transfers. Detailed information follows this section.
-
-- The card raises the Encoder interrupt.
-- The driver reads the transfer type, offset and size from Mailbox #10.
-- The driver constructs the scatter-gather array from enough free dma buffers
- to cover the size.
-- The driver schedules the DMA transfer via the ScheduleDMAtoHost API call.
-- The card raises the DMA Complete interrupt.
-- The driver checks the DMA status register for any errors.
-- The driver post-processes the newly transferred buffers.
-
-NOTE! It is possible that the Encoder and DMA Complete interrupts get raised
-simultaneously. (End of the last, start of the next, etc.)
-
-Mailbox #10
-===========
-
-The Flags, Command, Return Value and Timeout fields are ignored.
-
-Name: Mailbox #10
-Results[0]: Type: 0: MPEG.
-Results[1]: Offset: The position relative to the card's memory space.
-Results[2]: Size: The exact number of bytes to transfer.
-
-My speculation is that since the StartCapture API has a capture type of "RAW"
-available, that the type field will have other values that correspond to YUV
-and PCM data.
-
-Scatter-Gather Array
-====================
-
-The scatter-gather array is a contiguously allocated block of memory that
-tells the card the source and destination of each data-block to transfer.
-Card "addresses" are derived from the offset supplied by Mailbox #10. Host
-addresses are the physical memory location of the target DMA buffer.
-
-Each S-G array element is a struct of three 32-bit words. The first word is
-the source address, the second is the destination address. Both take up the
-entire 32 bits. The lowest 18 bits of the third word is the transfer byte
-count. The high-bit of the third word is the "last" flag. The last-flag tells
-the card to raise the DMA_DONE interrupt. From hard personal experience, if
-you forget to set this bit, the card will still "work" but the stream will
-most likely get corrupted.
-
-The transfer count must be a multiple of 256. Therefore, the driver will need
-to track how much data in the target buffer is valid and deal with it
-accordingly.
-
-Array Element:
-
-- 32-bit Source Address
-- 32-bit Destination Address
-- 14-bit reserved (high bit is the last flag)
-- 18-bit byte count
-
-DMA Transfer Status
-===================
-
-Register 0x0004 holds the DMA Transfer Status:
-
-Bit
-0 read completed
-1 write completed
-2 DMA read error
-3 DMA write error
-4 Scatter-Gather array error