diff options
| -rw-r--r-- | drivers/spi/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/spi/spi-bcmbca-hsspi.c | 651 |
3 files changed, 661 insertions, 0 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index db033d424bb5..2ede343fde42 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -199,6 +199,15 @@ config SPI_BCM_QSPI based platforms. This driver works for both SPI master for SPI NOR flash device as well as MSPI device. +config SPI_BCMBCA_HSSPI + tristate "Broadcom BCMBCA HS SPI controller driver" + depends on ARCH_BCMBCA || COMPILE_TEST + help + This enables support for the High Speed SPI controller present on + newer Broadcom BCMBCA SoCs. These SoCs include an updated SPI controller + that adds the capability to allow the driver to control chip select + explicitly. + config SPI_BITBANG tristate "Utilities for Bitbanging SPI masters" help diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index be9ba40ef8d0..fe92106447c3 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -30,6 +30,7 @@ obj-$(CONFIG_SPI_BCM2835) += spi-bcm2835.o obj-$(CONFIG_SPI_BCM2835AUX) += spi-bcm2835aux.o obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o +obj-$(CONFIG_SPI_BCMBCA_HSSPI) += spi-bcmbca-hsspi.o obj-$(CONFIG_SPI_BCM_QSPI) += spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.o obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o obj-$(CONFIG_SPI_BUTTERFLY) += spi-butterfly.o diff --git a/drivers/spi/spi-bcmbca-hsspi.c b/drivers/spi/spi-bcmbca-hsspi.c new file mode 100644 index 000000000000..d58033251c02 --- /dev/null +++ b/drivers/spi/spi-bcmbca-hsspi.c @@ -0,0 +1,651 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Broadcom BCMBCA High Speed SPI Controller driver + * + * Copyright 2000-2010 Broadcom Corporation + * Copyright 2012-2013 Jonas Gorski <jogo@openwrt.org> + * Copyright 2019-2022 Broadcom Ltd + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/dma-mapping.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/spi/spi.h> +#include <linux/mutex.h> +#include <linux/of.h> +#include <linux/spi/spi-mem.h> +#include <linux/pm_runtime.h> + +#define HSSPI_GLOBAL_CTRL_REG 0x0 +#define GLOBAL_CTRL_CS_POLARITY_SHIFT 0 +#define GLOBAL_CTRL_CS_POLARITY_MASK 0x000000ff +#define GLOBAL_CTRL_PLL_CLK_CTRL_SHIFT 8 +#define GLOBAL_CTRL_PLL_CLK_CTRL_MASK 0x0000ff00 +#define GLOBAL_CTRL_CLK_GATE_SSOFF BIT(16) +#define GLOBAL_CTRL_CLK_POLARITY BIT(17) +#define GLOBAL_CTRL_MOSI_IDLE BIT(18) + +#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4 + +#define HSSPI_INT_STATUS_REG 0x8 +#define HSSPI_INT_STATUS_MASKED_REG 0xc +#define HSSPI_INT_MASK_REG 0x10 + +#define HSSPI_PINGx_CMD_DONE(i) BIT((i * 8) + 0) +#define HSSPI_PINGx_RX_OVER(i) BIT((i * 8) + 1) +#define HSSPI_PINGx_TX_UNDER(i) BIT((i * 8) + 2) +#define HSSPI_PINGx_POLL_TIMEOUT(i) BIT((i * 8) + 3) +#define HSSPI_PINGx_CTRL_INVAL(i) BIT((i * 8) + 4) + +#define HSSPI_INT_CLEAR_ALL 0xff001f1f + +#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40) +#define PINGPONG_CMD_COMMAND_MASK 0xf +#define PINGPONG_COMMAND_NOOP 0 +#define PINGPONG_COMMAND_START_NOW 1 +#define PINGPONG_COMMAND_START_TRIGGER 2 +#define PINGPONG_COMMAND_HALT 3 +#define PINGPONG_COMMAND_FLUSH 4 +#define PINGPONG_CMD_PROFILE_SHIFT 8 +#define PINGPONG_CMD_SS_SHIFT 12 + +#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40) +#define HSSPI_PINGPONG_STATUS_SRC_BUSY BIT(1) + +#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20) +#define CLK_CTRL_FREQ_CTRL_MASK 0x0000ffff +#define CLK_CTRL_SPI_CLK_2X_SEL BIT(14) +#define CLK_CTRL_ACCUM_RST_ON_LOOP BIT(15) +#define CLK_CTRL_CLK_POLARITY BIT(16) + +#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20) +#define SIGNAL_CTRL_LATCH_RISING BIT(12) +#define SIGNAL_CTRL_LAUNCH_RISING BIT(13) +#define SIGNAL_CTRL_ASYNC_INPUT_PATH BIT(16) + +#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20) +#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8 +#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12 +#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16 +#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18 +#define MODE_CTRL_MODE_3WIRE BIT(20) +#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24 + +#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200) + +#define HSSPI_OP_MULTIBIT BIT(11) +#define HSSPI_OP_CODE_SHIFT 13 +#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT) +#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT) +#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT) +#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT) +#define HSSPI_OP_SETIRQ (4 << HSSPI_OP_CODE_SHIFT) + +#define HSSPI_BUFFER_LEN 512 +#define HSSPI_OPCODE_LEN 2 + +#define HSSPI_MAX_PREPEND_LEN 15 + +#define HSSPI_MAX_SYNC_CLOCK 30000000 + +#define HSSPI_SPI_MAX_CS 8 +#define HSSPI_BUS_NUM 1 /* 0 is legacy SPI */ +#define HSSPI_POLL_STATUS_TIMEOUT_MS 100 + +#define HSSPI_WAIT_MODE_POLLING 0 +#define HSSPI_WAIT_MODE_INTR 1 +#define HSSPI_WAIT_MODE_MAX HSSPI_WAIT_MODE_INTR + +#define SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT 0 +#define SPIM_CTRL_CS_OVERRIDE_SEL_MASK 0xff +#define SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT 8 +#define SPIM_CTRL_CS_OVERRIDE_VAL_MASK 0xff + +struct bcmbca_hsspi { + struct completion done; + struct mutex bus_mutex; + struct mutex msg_mutex; + struct platform_device *pdev; + struct clk *clk; + struct clk *pll_clk; + void __iomem *regs; + void __iomem *spim_ctrl; + u8 __iomem *fifo; + u32 speed_hz; + u8 cs_polarity; + u32 wait_mode; +}; + +static ssize_t wait_mode_show(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct spi_controller *ctrl = dev_get_drvdata(dev); + struct bcmbca_hsspi *bs = spi_master_get_devdata(ctrl); + + return sprintf(buf, "%d\n", bs->wait_mode); +} + +static ssize_t wait_mode_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct spi_controller *ctrl = dev_get_drvdata(dev); + struct bcmbca_hsspi *bs = spi_master_get_devdata(ctrl); + u32 val; + + if (kstrtou32(buf, 10, &val)) + return -EINVAL; + + if (val > HSSPI_WAIT_MODE_MAX) { + dev_warn(dev, "invalid wait mode %u\n", val); + return -EINVAL; + } + + mutex_lock(&bs->msg_mutex); + bs->wait_mode = val; + /* clear interrupt status to avoid spurious int on next transfer */ + if (val == HSSPI_WAIT_MODE_INTR) + __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG); + mutex_unlock(&bs->msg_mutex); + + return count; +} + +static DEVICE_ATTR_RW(wait_mode); + +static struct attribute *bcmbca_hsspi_attrs[] = { + &dev_attr_wait_mode.attr, + NULL, +}; + +static const struct attribute_group bcmbca_hsspi_group = { + .attrs = bcmbca_hsspi_attrs, +}; + +static void bcmbca_hsspi_set_cs(struct bcmbca_hsspi *bs, unsigned int cs, + bool active) +{ + u32 reg; + + /* No cs orerriden needed for SS7 internal cs on pcm based voice dev */ + if (cs == 7) + return; + + mutex_lock(&bs->bus_mutex); + + reg = __raw_readl(bs->spim_ctrl); + if (active) + reg |= BIT(cs + SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT); + else + reg &= ~BIT(cs + SPIM_CTRL_CS_OVERRIDE_SEL_SHIFT); + + __raw_writel(reg, bs->spim_ctrl); + + mutex_unlock(&bs->bus_mutex); +} + +static void bcmbca_hsspi_set_clk(struct bcmbca_hsspi *bs, + struct spi_device *spi, int hz) +{ + unsigned int profile = spi->chip_select; + u32 reg; + + reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz)); + __raw_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg, + bs->regs + HSSPI_PROFILE_CLK_CTRL_REG(profile)); + + reg = __raw_readl(bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); + if (hz > HSSPI_MAX_SYNC_CLOCK) + reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH; + else + reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH; + __raw_writel(reg, bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile)); + + mutex_lock(&bs->bus_mutex); + /* setup clock polarity */ + reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG); + reg &= ~GLOBAL_CTRL_CLK_POLARITY; + if (spi->mode & SPI_CPOL) + reg |= GLOBAL_CTRL_CLK_POLARITY; + __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG); + + mutex_unlock(&bs->bus_mutex); +} + +static int bcmbca_hsspi_wait_cmd(struct bcmbca_hsspi *bs, unsigned int cs) +{ + unsigned long limit; + u32 reg = 0; + int rc = 0; + + if (bs->wait_mode == HSSPI_WAIT_MODE_INTR) { + if (wait_for_completion_timeout(&bs->done, HZ) == 0) + rc = 1; + } else { + limit = jiffies + msecs_to_jiffies(HSSPI_POLL_STATUS_TIMEOUT_MS); + + while (!time_after(jiffies, limit)) { + reg = __raw_readl(bs->regs + HSSPI_PINGPONG_STATUS_REG(0)); + if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY) + cpu_relax(); + else + break; + } + if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY) + rc = 1; + } + + if (rc) + dev_err(&bs->pdev->dev, "transfer timed out!\n"); + + return rc; +} + +static int bcmbca_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t, + struct spi_message *msg) +{ + struct bcmbca_hsspi *bs = spi_master_get_devdata(spi->master); + unsigned int chip_select = spi->chip_select; + u16 opcode = 0; + int pending = t->len; + int step_size = HSSPI_BUFFER_LEN; + const u8 *tx = t->tx_buf; + u8 *rx = t->rx_buf; + u32 reg = 0, cs_act = 0; + + bcmbca_hsspi_set_clk(bs, spi, t->speed_hz); + + if (tx && rx) + opcode = HSSPI_OP_READ_WRITE; + else if (tx) + opcode = HSSPI_OP_WRITE; + else if (rx) + opcode = HSSPI_OP_READ; + + if (opcode != HSSPI_OP_READ) + step_size -= HSSPI_OPCODE_LEN; + + if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) || + (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) { + opcode |= HSSPI_OP_MULTIBIT; + + if (t->rx_nbits == SPI_NBITS_DUAL) + reg |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT; + if (t->tx_nbits == SPI_NBITS_DUAL) + reg |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT; + } + + __raw_writel(reg | 0xff, + bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select)); + + while (pending > 0) { + int curr_step = min_t(int, step_size, pending); + + reinit_completion(&bs->done); + if (tx) { + memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step); + tx += curr_step; + } + __raw_writew((u16)cpu_to_be16(opcode | curr_step), bs->fifo); + + /* enable interrupt */ + if (bs->wait_mode == HSSPI_WAIT_MODE_INTR) + __raw_writel(HSSPI_PINGx_CMD_DONE(0), + bs->regs + HSSPI_INT_MASK_REG); + + if (!cs_act) { + /* must apply cs signal as close as the cmd starts */ + bcmbca_hsspi_set_cs(bs, chip_select, true); + cs_act = 1; + } + + reg = chip_select << PINGPONG_CMD_SS_SHIFT | + chip_select << PINGPONG_CMD_PROFILE_SHIFT | + PINGPONG_COMMAND_START_NOW; + __raw_writel(reg, bs->regs + HSSPI_PINGPONG_COMMAND_REG(0)); + + if (bcmbca_hsspi_wait_cmd(bs, spi->chip_select)) + return -ETIMEDOUT; + + pending -= curr_step; + + if (rx) { + memcpy_fromio(rx, bs->fifo, curr_step); + rx += curr_step; + } + } + + return 0; +} + +static int bcmbca_hsspi_setup(struct spi_device *spi) +{ + struct bcmbca_hsspi *bs = spi_master_get_devdata(spi->master); + u32 reg; + + reg = __raw_readl(bs->regs + + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING); + if (spi->mode & SPI_CPHA) + reg |= SIGNAL_CTRL_LAUNCH_RISING; + else + reg |= SIGNAL_CTRL_LATCH_RISING; + __raw_writel(reg, bs->regs + + HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select)); + + mutex_lock(&bs->bus_mutex); + reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG); + + if (spi->mode & SPI_CS_HIGH) + reg |= BIT(spi->chip_select); + else + reg &= ~BIT(spi->chip_select); + __raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG); + + if (spi->mode & SPI_CS_HIGH) + bs->cs_polarity |= BIT(spi->chip_select); + else + bs->cs_polarity &= ~BIT(spi->chip_select); + + reg = __raw_readl(bs->spim_ctrl); + reg &= ~BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); + if (spi->mode & SPI_CS_HIGH) + reg |= BIT(spi->chip_select + SPIM_CTRL_CS_OVERRIDE_VAL_SHIFT); + __raw_writel(reg, bs->spim_ctrl); + + mutex_unlock(&bs->bus_mutex); + + return 0; +} + +static int bcmbca_hsspi_transfer_one(struct spi_master *master, + struct spi_message *msg) +{ + struct bcmbca_hsspi *bs = spi_master_get_devdata(master); + struct spi_transfer *t; + struct spi_device *spi = msg->spi; + int status = -EINVAL; + bool keep_cs = false; + + mutex_lock(&bs->msg_mutex); + list_for_each_entry(t, &msg->transfers, transfer_list) { + status = bcmbca_hsspi_do_txrx(spi, t, msg); + if (status) + break; + + spi_transfer_delay_exec(t); + + if (t->cs_change) { + if (list_is_last(&t->transfer_list, &msg->transfers)) { + keep_cs = true; + } else { + if (!t->cs_off) + bcmbca_hsspi_set_cs(bs, spi->chip_select, false); + + spi_transfer_cs_change_delay_exec(msg, t); + + if (!list_next_entry(t, transfer_list)->cs_off) + bcmbca_hsspi_set_cs(bs, spi->chip_select, true); + } + } else if (!list_is_last(&t->transfer_list, &msg->transfers) && + t->cs_off != list_next_entry(t, transfer_list)->cs_off) { + bcmbca_hsspi_set_cs(bs, spi->chip_select, t->cs_off); + } + + msg->actual_length += t->len; + } + + mutex_unlock(&bs->msg_mutex); + + if (status || !keep_cs) + bcmbca_hsspi_set_cs(bs, spi->chip_select, false); + + msg->status = status; + spi_finalize_current_message(master); + + return 0; +} + +static irqreturn_t bcmbca_hsspi_interrupt(int irq, void *dev_id) +{ + struct bcmbca_hsspi *bs = (struct bcmbca_hsspi *)dev_id; + + if (__raw_readl(bs->regs + HSSPI_INT_STATUS_MASKED_REG) == 0) + return IRQ_NONE; + + __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG); + __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG); + + complete(&bs->done); + + return IRQ_HANDLED; +} + +static int bcmbca_hsspi_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct bcmbca_hsspi *bs; + struct resource *res_mem; + void __iomem *spim_ctrl; + void __iomem *regs; + struct device *dev = &pdev->dev; + struct clk *clk, *pll_clk = NULL; + int irq, ret; + u32 reg, rate, num_cs = HSSPI_SPI_MAX_CS; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hsspi"); + if (!res_mem) + return -EINVAL; + regs = devm_ioremap_resource(dev, res_mem); + if (IS_ERR(regs)) + return PTR_ERR(regs); + + res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "spim-ctrl"); + if (!res_mem) + return -EINVAL; + spim_ctrl = devm_ioremap_resource(dev, res_mem); + if (IS_ERR(spim_ctrl)) + return PTR_ERR(spim_ctrl); + + clk = devm_clk_get(dev, "hsspi"); + if (IS_ERR(clk)) + return PTR_ERR(clk); + + ret = clk_prepare_enable(clk); + if (ret) + return ret; + + rate = clk_get_rate(clk); + if (!rate) { + pll_clk = devm_clk_get(dev, "pll"); + + if (IS_ERR(pll_clk)) { + ret = PTR_ERR(pll_clk); + goto out_disable_clk; + } + + ret = clk_prepare_enable(pll_clk); + if (ret) + goto out_disable_clk; + + rate = clk_get_rate(pll_clk); + if (!rate) { + ret = -EINVAL; + goto out_disable_pll_clk; + } + } + + master = spi_alloc_master(&pdev->dev, sizeof(*bs)); + if (!master) { + ret = -ENOMEM; + goto out_disable_pll_clk; + } + + bs = spi_master_get_devdata(master); + bs->pdev = pdev; + bs->clk = clk; + bs->pll_clk = pll_clk; + bs->regs = regs; + bs->spim_ctrl = spim_ctrl; + bs->speed_hz = rate; + bs->fifo = (u8 __iomem *) (bs->regs + HSSPI_FIFO_REG(0)); + bs->wait_mode = HSSPI_WAIT_MODE_POLLING; + + mutex_init(&bs->bus_mutex); + mutex_init(&bs->msg_mutex); + init_completion(&bs->done); + + master->dev.of_node = dev->of_node; + if (!dev->of_node) + master->bus_num = HSSPI_BUS_NUM; + + of_property_read_u32(dev->of_node, "num-cs", &num_cs); + if (num_cs > 8) { + dev_warn(dev, "unsupported number of cs (%i), reducing to 8\n", + num_cs); + num_cs = HSSPI_SPI_MAX_CS; + } + master->num_chipselect = num_cs; + master->setup = bcmbca_hsspi_setup; + master->transfer_one_message = bcmbca_hsspi_transfer_one; + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | + SPI_RX_DUAL | SPI_TX_DUAL; + master->bits_per_word_mask = SPI_BPW_MASK(8); + master->auto_runtime_pm = true; + + platform_set_drvdata(pdev, master); + + /* Initialize the hardware */ + __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG); + + /* clean up any pending interrupts */ + __raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG); + + /* read out default CS polarities */ + reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG); + bs->cs_polarity = reg & GLOBAL_CTRL_CS_POLARITY_MASK; + __raw_writel(reg | GLOBAL_CTRL_CLK_GATE_SSOFF, + bs->regs + HSSPI_GLOBAL_CTRL_REG); + + if (irq > 0) { + ret = devm_request_irq(dev, irq, bcmbca_hsspi_interrupt, IRQF_SHARED, + pdev->name, bs); + if (ret) + goto out_put_master; + } + + pm_runtime_enable(&pdev->dev); + + if (sysfs_create_group(&pdev->dev.kobj, &bcmbca_hsspi_group)) { + dev_err(&pdev->dev, "couldn't register sysfs group\n"); + goto out_pm_disable; + } + + /* register and we are done */ + ret = devm_spi_register_master(dev, master); + if (ret) + goto out_sysgroup_disable; + + dev_info(dev, "Broadcom BCMBCA High Speed SPI Controller driver"); + + return 0; + +out_sysgroup_disable: + sysfs_remove_group(&pdev->dev.kobj, &bcmbca_hsspi_group); +out_pm_disable: + pm_runtime_disable(&pdev->dev); +out_put_master: + spi_master_put(master); +out_disable_pll_clk: + clk_disable_unprepare(pll_clk); +out_disable_clk: + clk_disable_unprepare(clk); + return ret; +} + +static int bcmbca_hsspi_remove(struct platform_device *pdev) +{ + struct spi_master *master = platform_get_drvdata(pdev); + struct bcmbca_hsspi *bs = spi_master_get_devdata(master); + + /* reset the hardware and block queue progress */ + __raw_writel(0, bs->regs + HSSPI_INT_MASK_REG); + clk_disable_unprepare(bs->pll_clk); + clk_disable_unprepare(bs->clk); + sysfs_remove_group(&pdev->dev.kobj, &bcmbca_hsspi_group); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int bcmbca_hsspi_suspend(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct bcmbca_hsspi *bs = spi_master_get_devdata(master); + + spi_master_suspend(master); + clk_disable_unprepare(bs->pll_clk); + clk_disable_unprepare(bs->clk); + + return 0; +} + +static int bcmbca_hsspi_resume(struct device *dev) +{ + struct spi_master *master = dev_get_drvdata(dev); + struct bcmbca_hsspi *bs = spi_master_get_devdata(master); + int ret; + + ret = clk_prepare_enable(bs->clk); + if (ret) + return ret; + + if (bs->pll_clk) { + ret = clk_prepare_enable(bs->pll_clk); + if (ret) { + clk_disable_unprepare(bs->clk); + return ret; + } + } + + spi_master_resume(master); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(bcmbca_hsspi_pm_ops, bcmbca_hsspi_suspend, + bcmbca_hsspi_resume); + +static const struct of_device_id bcmbca_hsspi_of_match[] = { + { .compatible = "brcm,bcmbca-hsspi-v1.1", }, + {}, +}; + +MODULE_DEVICE_TABLE(of, bcmbca_hsspi_of_match); + +static struct platform_driver bcmbca_hsspi_driver = { + .driver = { + .name = "bcmbca-hsspi", + .pm = &bcmbca_hsspi_pm_ops, + .of_match_table = bcmbca_hsspi_of_match, + }, + .probe = bcmbca_hsspi_probe, + .remove = bcmbca_hsspi_remove, +}; + +module_platform_driver(bcmbca_hsspi_driver); + +MODULE_ALIAS("platform:bcmbca_hsspi"); +MODULE_DESCRIPTION("Broadcom BCMBCA High Speed SPI Controller driver"); +MODULE_LICENSE("GPL"); |