| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 6.10-rc4.
Included in here are:
- thunderbolt debugfs bugfix
- USB typec bugfixes
- kcov usb bugfix
- xhci bugfixes
- usb-storage bugfix
- dt-bindings bugfix
- cdc-wdm log message spam bugfix
All of these, except for the last cdc-wdm log level change, have been
in linux-next for a while with no reported problems. The cdc-wdm
bugfix has been tested by syzbot and proved to fix the reported cpu
lockup issues when the log is constantly spammed by a broken device"
* tag 'usb-6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: class: cdc-wdm: Fix CPU lockup caused by excessive log messages
xhci: Handle TD clearing for multiple streams case
xhci: Apply broken streams quirk to Etron EJ188 xHCI host
xhci: Apply reset resume quirk to Etron EJ188 xHCI host
xhci: Set correct transferred length for cancelled bulk transfers
usb-storage: alauda: Check whether the media is initialized
usb: typec: ucsi: Ack also failed Get Error commands
kcov, usb: disable interrupts in kcov_remote_start_usb_softirq
dt-bindings: usb: realtek,rts5411: Add missing "additionalProperties" on child nodes
usb: typec: tcpm: Ignore received Hard Reset in TOGGLING state
usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps
USB: xen-hcd: Traverse host/ when CONFIG_USB_XEN_HCD is selected
usb: typec: ucsi: glink: increase max ports for x1e80100
Revert "usb: chipidea: move ci_ulpi_init after the phy initialization"
thunderbolt: debugfs: Fix margin debugfs node creation condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small char/misc and iio driver fixes for
6.10-rc4. Included in here are the following:
- iio driver fixes for a bunch of reported problems.
- mei driver fixes for a number of reported issues.
- amiga parport driver build fix.
- .editorconfig fix that was causing lots of unintended whitespace
changes to happen to files when they were being edited. Unless we
want to sweep the whole tree and remove all trailing whitespace at
once, this is needed for the .editorconfig file to be able to be
used at all. This change is required because the original
submitters never touched older files in the tree.
- jfs bugfix for a buffer overflow
The jfs bugfix is in here as I didn't know where else to put it, and
it's been ignored for a while as the filesystem seems to be abandoned
and I'm tired of seeing the same issue reported in multiple places.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (25 commits)
.editorconfig: remove trim_trailing_whitespace option
jfs: xattr: fix buffer overflow for invalid xattr
misc: microchip: pci1xxxx: Fix a memory leak in the error handling of gp_aux_bus_probe()
misc: microchip: pci1xxxx: fix double free in the error handling of gp_aux_bus_probe()
parport: amiga: Mark driver struct with __refdata to prevent section mismatch
mei: vsc: Fix wrong invocation of ACPI SID method
mei: vsc: Don't stop/restart mei device during system suspend/resume
mei: me: release irq in mei_me_pci_resume error path
mei: demote client disconnect warning on suspend to debug
iio: inkern: fix channel read regression
iio: imu: inv_mpu6050: stabilized timestamping in interrupt
iio: adc: ad7173: Fix sampling frequency setting
iio: adc: ad7173: Clear append status bit
iio: imu: inv_icm42600: delete unneeded update watermark call
iio: imu: inv_icm42600: stabilized timestamp in interrupt
iio: invensense: fix odr switching to same value
iio: adc: ad7173: Remove index from temp channel
iio: adc: ad7173: Add ad7173_device_info names
iio: adc: ad7173: fix buffers enablement for ad7176-2
iio: temperature: mlx90635: Fix ERR_PTR dereference in mlx90635_probe()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential read out of bounds in hid-asus (Andrew Ballance)
- fix endian-conversion on little endian systems in intel-ish-hid (Arnd
Bergmann)
- A couple of new input event codes (Aseda Aboagye)
- errors handling fixes in hid-nvidia-shield (Chen Ni), hid-nintendo
(Christophe JAILLET), hid-logitech-dj (José Expósito)
- current leakage fix while the device is in suspend on a i2c-hid
laptop (Johan Hovold)
- other assorted smaller fixes and device ID / quirk entry additions
* tag 'for-linus-2024060801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: Ignore battery for ELAN touchscreens 2F2C and 4116
HID: i2c-hid: elan: fix reset suspend current leakage
dt-bindings: HID: i2c-hid: elan: add 'no-reset-on-power-off' property
dt-bindings: HID: i2c-hid: elan: add Elan eKTH5015M
dt-bindings: HID: i2c-hid: add dedicated Ilitek ILI2901 schema
input: Add support for "Do Not Disturb"
input: Add event code for accessibility key
hid: asus: asus_report_fixup: fix potential read out of bounds
HID: logitech-hidpp: add missing MODULE_DESCRIPTION() macro
HID: intel-ish-hid: fix endian-conversion
HID: nintendo: Fix an error handling path in nintendo_hid_probe()
HID: logitech-dj: Fix memory leak in logi_dj_recv_switch_to_dj_mode()
HID: core: remove unnecessary WARN_ON() in implement()
HID: nvidia-shield: Add missing check for input_ff_create_memless
HID: intel-ish-hid: Fix build error for COMPILE_TEST
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix the initial state of the save button in 'make gconfig'
- Improve the Kconfig documentation
- Fix a Kconfig bug regarding property visibility
- Fix build breakage for systems where 'sed' is not installed in /bin
- Fix a false warning about missing MODULE_DESCRIPTION()
* tag 'kbuild-fixes-v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: do not warn about missing MODULE_DESCRIPTION() for vmlinux.o
kbuild: explicitly run mksysmap as sed script from link-vmlinux.sh
kconfig: remove wrong expr_trans_bool()
kconfig: doc: document behavior of 'select' and 'imply' followed by 'if'
kconfig: doc: fix a typo in the note about 'imply'
kconfig: gconf: give a proper initial state to the Save button
kconfig: remove unneeded code for user-supplied values being out of range
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fixes for the new ipu6 driver (and related fixes to mei csi driver)
- fix a double debugfs remove logic at mgb4 driver
- a documentation fix
* tag 'media/v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: intel/ipu6: add csi2 port sanity check in notifier bound
media: intel/ipu6: update the maximum supported csi2 port number to 6
media: mei: csi: Warn less verbosely of a missing device fwnode
media: mei: csi: Put the IPU device reference
media: intel/ipu6: fix the buffer flags caused by wrong parentheses
media: intel/ipu6: Fix an error handling path in isys_probe()
media: intel/ipu6: Move isys_remove() close to isys_probe()
media: intel/ipu6: Fix some redundant resources freeing in ipu6_pci_remove()
media: Documentation: v4l: Fix ACTIVE route flag
media: mgb4: Fix double debugfs remove
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"14 hotfixes, 6 of which are cc:stable.
All except the nilfs2 fix affect MM and all are singletons - see the
chagelogs for details"
* tag 'mm-hotfixes-stable-2024-06-07-15-24' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
nilfs2: fix nilfs_empty_dir() misjudgment and long loop on I/O errors
mm: fix xyz_noprof functions calling profiled functions
codetag: avoid race at alloc_slab_obj_exts
mm/hugetlb: do not call vma_add_reservation upon ENOMEM
mm/ksm: fix ksm_zero_pages accounting
mm/ksm: fix ksm_pages_scanned accounting
kmsan: do not wipe out origin when doing partial unpoisoning
vmalloc: check CONFIG_EXECMEM in is_vmalloc_or_module_addr()
mm: page_alloc: fix highatomic typing in multi-block buddies
nilfs2: fix potential kernel bug due to lack of writeback flag waiting
memcg: remove the lockdep assert from __mod_objcg_mlstate()
mm: arm64: fix the out-of-bounds issue in contpte_clear_young_dirty_ptes
mm: huge_mm: fix undefined reference to `mthp_stats' for CONFIG_SYSFS=n
mm: drop the 'anon_' prefix for swap-out mTHP counters
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
1st set of IIO fixes for the 6.10 cycle.
The usual mixed bag of old and new driver bugs plus one core issue that
highlighted we have some documentation issues that we need to fix
as a follow up action.
core in kernel interface
- Wrong return value documentation didn't help with an error in
a cleanup. Result is that thermal is failing to read the temperature.
adi,ad3552r
- Fix DT binding output range sign error.
adi,ad5592r
- Wrong scaling on temperature channel.
adi,ad7173
- Driver assumed all supported devices had input buffers. Make sure not to
enable them on the ad7176-2 which doesn't.
- Add some missing device names for recently added models.
- Drop an unneeded zero index on the single temperature channel.
- Clear buffered capture specific control bit when returning to on
demand sampling which otherwise no longer works.
- Make sampling frequency per channel rather than just setting it for the
first channel.
adi,ad9467
- Capital S for sign of channel whereas ABI is lowercase.
bosch,bmi323
- Make sure to release the trigger even on error paths in the trigger
handler as otherwise there is no path to recover.
bosch,bmp280
- Avoid an overflow in calculating the temperature.
invensense,timestamp helper
- Fix case where ODR is being switched to the existing ODR an update that
never finishes.
- Fix an issue with the timestamp being updated whilst still handling
previous interrupt (icm42600 and mpu6050)
invensense,icm42600
- Don't update the watermark parameters twice.
melexis,mlx90635
- Fix variable returned as error code.
* tag 'iio-fixes-for-6.10a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: inkern: fix channel read regression
iio: imu: inv_mpu6050: stabilized timestamping in interrupt
iio: adc: ad7173: Fix sampling frequency setting
iio: adc: ad7173: Clear append status bit
iio: imu: inv_icm42600: delete unneeded update watermark call
iio: imu: inv_icm42600: stabilized timestamp in interrupt
iio: invensense: fix odr switching to same value
iio: adc: ad7173: Remove index from temp channel
iio: adc: ad7173: Add ad7173_device_info names
iio: adc: ad7173: fix buffers enablement for ad7176-2
iio: temperature: mlx90635: Fix ERR_PTR dereference in mlx90635_probe()
iio: imu: bmi323: Fix trigger notification in case of error
iio: dac: ad5592r: fix temperature channel scaling value
iio: pressure: bmp280: Fix BMP580 temperature reading
dt-bindings: iio: dac: fix ad354xr output range
iio: adc: ad9467: fix scan type sign
|
|
When the power supply is shared with other peripherals the reset line
can be wired in such a way that it can remain deasserted regardless of
whether the supply is on or not.
This is important as it can be used to avoid holding the controller in
reset for extended periods of time when it remains powered, something
which can lead to increased power consumption. Leaving reset deasserted
also avoids leaking current through the reset circuitry pull-up
resistors.
Add a new 'no-reset-on-power-off' devicetree property which can be used
by the OS to determine when reset needs to be asserted on power down.
Note that this property can also be used when the supply cannot be
turned off by the OS at all.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240507144821.12275-4-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Add a compatible string for the Elan eKTH5015M touch controller.
Judging from the current binding and commit bd3cba00dcc6 ("HID: i2c-hid:
elan: Add support for Elan eKTH6915 i2c-hid touchscreens"), eKTH5015M
appears to be compatible with eKTH6915. Notably the power-on sequence is
the same.
While at it, drop a redundant label from the example.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240507144821.12275-3-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
The Ilitek ILI2901 touch screen controller was apparently incorrectly
added to the Elan eKTH6915 schema simply because it also has a reset
gpio and is currently managed by the Elan driver in Linux.
The two controllers are not related even if an unfortunate wording in
the commit message adding the Ilitek compatible made it sound like they
were.
Add a dedicated schema for the ILI2901 which does not specify the I2C
address (which is likely 0x41 rather than 0x10 as for other Ilitek touch
controllers) to avoid cluttering the Elan schema with unrelated devices
and to make it easier to find the correct schema when adding further
Ilitek controllers.
Fixes: d74ac6f60a7e ("dt-bindings: HID: i2c-hid: elan: Introduce Ilitek ili2901")
Cc: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240507144821.12275-2-johan+linaro@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The core change is to detect unusually large number of VPD pages
(caused by device manufacturers having an endiannes issue) and reject
them rather than trying to parse a huge non-existent array.
The remaining fixes are in drivers the most user visible of which is
the ALUA state transition recognition (leads to intermittent I/O
errors in some situations otherwise)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: mcq: Fix error output and clean up ufshcd_mcq_abort()
scsi: core: Handle devices which return an unusually large VPD page count
scsi: mpt3sas: Add missing kerneldoc parameter descriptions
scsi: qedf: Set qed_slowpath_params to zero before use
scsi: qedf: Wait for stag work during unload
scsi: qedf: Don't process stag work during unload and recovery
scsi: sr: Fix unintentional arithmetic wraparound
scsi: core: alua: I/O errors for ALUA state transitions
scsi: mpi3mr: Use proper format specifier in mpi3mr_sas_port_add()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from BPF and big collection of fixes for WiFi core and
drivers.
Current release - regressions:
- vxlan: fix regression when dropping packets due to invalid src
addresses
- bpf: fix a potential use-after-free in bpf_link_free()
- xdp: revert support for redirect to any xsk socket bound to the
same UMEM as it can result in a corruption
- virtio_net:
- add missing lock protection when reading return code from
control_buf
- fix false-positive lockdep splat in DIM
- Revert "wifi: wilc1000: convert list management to RCU"
- wifi: ath11k: fix error path in ath11k_pcic_ext_irq_config
Previous releases - regressions:
- rtnetlink: make the "split" NLM_DONE handling generic, restore the
old behavior for two cases where we started coalescing those
messages with normal messages, breaking sloppily-coded userspace
- wifi:
- cfg80211: validate HE operation element parsing
- cfg80211: fix 6 GHz scan request building
- mt76: mt7615: add missing chanctx ops
- ath11k: move power type check to ASSOC stage, fix connecting to
6 GHz AP
- ath11k: fix WCN6750 firmware crash caused by 17 num_vdevs
- rtlwifi: ignore IEEE80211_CONF_CHANGE_RETRY_LIMITS
- iwlwifi: mvm: fix a crash on 7265
Previous releases - always broken:
- ncsi: prevent multi-threaded channel probing, a spec violation
- vmxnet3: disable rx data ring on dma allocation failure
- ethtool: init tsinfo stats if requested, prevent unintentionally
reporting all-zero stats on devices which don't implement any
- dst_cache: fix possible races in less common IPv6 features
- tcp: auth: don't consider TCP_CLOSE to be in TCP_AO_ESTABLISHED
- ax25: fix two refcounting bugs
- eth: ionic: fix kernel panic in XDP_TX action
Misc:
- tcp: count CLOSE-WAIT sockets for TCP_MIB_CURRESTAB"
* tag 'net-6.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (107 commits)
selftests: net: lib: set 'i' as local
selftests: net: lib: avoid error removing empty netns name
selftests: net: lib: support errexit with busywait
net: ethtool: fix the error condition in ethtool_get_phy_stats_ethtool()
ipv6: fix possible race in __fib6_drop_pcpu_from()
af_unix: Annotate data-race of sk->sk_shutdown in sk_diag_fill().
af_unix: Use skb_queue_len_lockless() in sk_diag_show_rqlen().
af_unix: Use skb_queue_empty_lockless() in unix_release_sock().
af_unix: Use unix_recvq_full_lockless() in unix_stream_connect().
af_unix: Annotate data-race of net->unx.sysctl_max_dgram_qlen.
af_unix: Annotate data-races around sk->sk_sndbuf.
af_unix: Annotate data-races around sk->sk_state in UNIX_DIAG.
af_unix: Annotate data-race of sk->sk_state in unix_stream_read_skb().
af_unix: Annotate data-races around sk->sk_state in sendmsg() and recvmsg().
af_unix: Annotate data-race of sk->sk_state in unix_accept().
af_unix: Annotate data-race of sk->sk_state in unix_stream_connect().
af_unix: Annotate data-races around sk->sk_state in unix_write_space() and poll().
af_unix: Annotate data-race of sk->sk_state in unix_inq_len().
af_unix: Annodate data-races around sk->sk_state for writers.
af_unix: Set sk->sk_state under unix_state_lock() for truly disconencted peer.
...
|
|
Pull tomoyo fixlet from Tetsuo Handa:
"Single patch to update project links, no behavior changes"
* tag 'tomoyo-pr-20240606' of git://git.code.sf.net/p/tomoyo/tomoyo:
tomoyo: update project links
|
|
Documentation/kbuild/kconfig-language.rst explains the behavior of
'select' as follows:
reverse dependencies can be used to force a lower limit of
another symbol. The value of the current menu symbol is used as the
minimal value <symbol> can be set to.
This is not true when the 'select' property is followed by 'if'.
[Test Code]
config MODULES
def_bool y
modules
config A
def_tristate y
select C if B
config B
def_tristate m
config C
tristate
[Result]
CONFIG_MODULES=y
CONFIG_A=y
CONFIG_B=m
CONFIG_C=m
If "the value of A is used as the minimal value C can be set to",
C must be 'y'.
The actual behavior is "C is selected by (A && B)". The lower limit of
C is downgraded due to B being 'm'.
This behavior is kind of weird, and this has arisen several times in
the mailing list.
I do not know whether it is a bug or intended behavior. Anyway, it is
not feasible to change it now because many Kconfig files are written
based on this behavior. The same applies to 'imply'.
Document this (but reserve the possibility for a future change).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
|
|
This sentence does not make sense due to a typo. Fix it.
Fixes: def2fbffe62c ("kconfig: allow symbols implied by y to become m")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
|
|
The mTHP swap related counters: 'anon_swpout' and 'anon_swpout_fallback'
are confusing with an 'anon_' prefix, since the shmem can swap out
non-anonymous pages. So drop the 'anon_' prefix to keep consistent with
the old swap counter names.
This is needed in 6.10-rcX to avoid having an inconsistent ABI out in the
field.
Link: https://lkml.kernel.org/r/7a8989c13299920d7589007a30065c3e2c19f0e0.1716431702.git.baolin.wang@linux.alibaba.com
Fixes: d0f048ac39f6 ("mm: add per-order mTHP anon_swpout and anon_swpout_fallback counters")
Fixes: 42248b9d34ea ("mm: add docs for per-order mTHP counters and transhuge_page ABI")
Signed-off-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Suggested-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Barry Song <baohua@kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Lance Yang <ioworker0@gmail.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This reverts commit 968595a93669b6b4f6d1fcf80cf2d97956b6868f.
Reported-by: Yuval El-Hanany <YuvalE@radware.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/xdp-newbies/8100DBDC-0B7C-49DB-9995-6027F6E63147@radware.com
Link: https://lore.kernel.org/bpf/20240604122927.29080-3-magnus.karlsson@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix regression in 'interrupt-map' handling affecting Apple M1 mini
(at least)
- Fix binding example warning in stm32 st,mlahb binding
- Fix schema error in Allwinner platform binding causing lots of
spurious warnings
- Add missing MODULE_DESCRIPTION() to DT kunit tests
* tag 'devicetree-fixes-for-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: property: Fix fw_devlink handling of interrupt-map
of/irq: Factor out parsing of interrupt-map parent phandle+args from of_irq_parse_raw()
dt-bindings: arm: stm32: st,mlahb: Drop spurious "reg" property from example
dt-bindings: arm: sunxi: Fix incorrect '-' usage
of: of_test: add MODULE_DESCRIPTION()
|
|
child nodes
All nodes need an explicit additionalProperties or unevaluatedProperties
unless a $ref has one that's false. As that is not the case with
usb-device.yaml, "additionalProperties" is needed here.
Fixes: c44d9dab31d6 ("dt-bindings: usb: Add downstream facing ports to realtek binding")
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20240523194500.2958192-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TOMOYO project has moved to SourceForge.net .
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- dma-mapping benchmark error handling fixes (Fedor Pchelkin)
- correct a config symbol reference in the DMA API documentation (Lukas
Bulwahn)
* tag 'dma-mapping-6.10-2024-05-31' of git://git.infradead.org/users/hch/dma-mapping:
Documentation/core-api: correct reference to SWIOTLB_DYNAMIC
dma-mapping: benchmark: handle NUMA_NO_NODE correctly
dma-mapping: benchmark: fix node id validation
dma-mapping: benchmark: avoid needless copy_to_user if benchmark fails
dma-mapping: benchmark: fix up kthread-related error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- a use-after-free bugfix
- Kconfig fixes for randconfig builds
- allow setting touchscreen_dmi quirks from the cmdline for debugging
- touchscreen_dmi quirks for two new laptop/tablet models
* tag 'platform-drivers-x86-v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: touchscreen_dmi: Add info for the EZpad 6s Pro
platform/x86: touchscreen_dmi: Add info for GlobalSpace SolT IVW 11.6" tablet
platform/x86: touchscreen_dmi: Add support for setting touchscreen properties from cmdline
platform/x86: thinkpad_acpi: Select INPUT_SPARSEKMAP in Kconfig
platform/x86: x86-android-tablets: Add "select LEDS_CLASS"
platform/x86: ISST: fix use-after-free in tpmi_sst_dev_remove()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to avoid pt_regs aliasing with idle thread stacks on secondary
harts.
- HAVE_ARCH_HUGE_VMAP is enabled on XIP kernels, which fixes boot
issues on XIP systems with huge pages.
- An update to the uABI documentation clarifying that only scalar
misaligned accesses were grandfathered in as supported, as the vector
extension did not exist at the time the uABI was frozen.
- A fix for the recently-added byte/half atomics to avoid losing the
fully ordered decorations.
* tag 'riscv-for-linus-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix fully ordered LR/SC xchg[8|16]() implementations
Documentation: RISC-V: uabi: Only scalar misaligned loads are supported
riscv: enable HAVE_ARCH_HUGE_VMAP for XIP kernel
riscv: prevent pt_regs corruption for secondary idle threads
|
|
We're stuck supporting scalar misaligned loads in userspace because they
were part of the ISA at the time we froze the uABI. That wasn't the
case for vector misaligned accesses, so depending on them
unconditionally is a userspace bug. All extant vector hardware traps on
these misaligned accesses.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240524185600.5919-1-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- gro: initialize network_offset in network layer
- tcp: reduce accepted window in NEW_SYN_RECV state
Current release - new code bugs:
- eth: mlx5e: do not use ptp structure for tx ts stats when not
initialized
- eth: ice: check for unregistering correct number of devlink params
Previous releases - regressions:
- bpf: Allow delete from sockmap/sockhash only if update is allowed
- sched: taprio: extend minimum interval restriction to entire cycle
too
- netfilter: ipset: add list flush to cancel_gc
- ipv4: fix address dump when IPv4 is disabled on an interface
- sock_map: avoid race between sock_map_close and sk_psock_put
- eth: mlx5: use mlx5_ipsec_rx_status_destroy to correctly delete
status rules
Previous releases - always broken:
- core: fix __dst_negative_advice() race
- bpf:
- fix multi-uprobe PID filtering logic
- fix pkt_type override upon netkit pass verdict
- netfilter: tproxy: bail out if IP has been disabled on the device
- af_unix: annotate data-race around unix_sk(sk)->addr
- eth: mlx5e: fix UDP GSO for encapsulated packets
- eth: idpf: don't enable NAPI and interrupts prior to allocating Rx
buffers
- eth: i40e: fully suspend and resume IO operations in EEH case
- eth: octeontx2-pf: free send queue buffers incase of leaf to inner
- eth: ipvlan: dont Use skb->sk in ipvlan_process_v{4,6}_outbound"
* tag 'net-6.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
netdev: add qstat for csum complete
ipvlan: Dont Use skb->sk in ipvlan_process_v{4,6}_outbound
net: ena: Fix redundant device NUMA node override
ice: check for unregistering correct number of devlink params
ice: fix 200G PHY types to link speed mapping
i40e: Fully suspend and resume IO operations in EEH case
i40e: factoring out i40e_suspend/i40e_resume
e1000e: move force SMBUS near the end of enable_ulp function
net: dsa: microchip: fix RGMII error in KSZ DSA driver
ipv4: correctly iterate over the target netns in inet_dump_ifaddr()
net: fix __dst_negative_advice() race
nfc/nci: Add the inconsistency check between the input data length and count
MAINTAINERS: dwmac: starfive: update Maintainer
net/sched: taprio: extend minimum interval restriction to entire cycle too
net/sched: taprio: make q->picos_per_byte available to fill_sched_entry()
netfilter: nft_fib: allow from forward/input without iif selector
netfilter: tproxy: bail out if IP has been disabled on the device
netfilter: nft_payload: skbuff vlan metadata mangle support
net: ti: icssg-prueth: Fix start counter for ft1 filter
sock_map: avoid race between sock_map_close and sk_psock_put
...
|
|
Recent commit 0cfe71f45f42 ("netdev: add queue stats") added
a lot of useful stats, but only those immediately needed by virtio.
Presumably virtio does not support CHECKSUM_COMPLETE,
so statistic for that form of checksumming wasn't included.
Other drivers will definitely need it, in fact we expect it
to be needed in net-next soon (mlx5). So let's add the definition
of the counter for CHECKSUM_COMPLETE to uAPI in net already,
so that the counters are in a more natural order (all subsequent
counters have not been present in any released kernel, yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Fixes: 0cfe71f45f42 ("netdev: add queue stats")
Link: https://lore.kernel.org/r/20240529163547.3693194-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
"reg" is not documented nor used for st,mlahb, so drop it from the
example to fix the warning:
Documentation/devicetree/bindings/arm/stm32/st,mlahb.example.dtb: ahb@38000000: Unevaluated properties are not allowed ('reg' was unexpected)
from schema $id: http://devicetree.org/schemas/arm/stm32/st,mlahb.yaml#
Since "reg" is dropped, the unit-address must be as well.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240523154208.2457864-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Commit 6bc6bf8a940a ("dt-bindings: arm: sunxi: document Anbernic RG35XX
handheld gaming device variants") mistakenly added '-' on each line
which created empty (i.e. description only) schemas matching anything.
This causes validation to fail on all the root node compatibles as
there are multiple oneOf clauses passing.
Fixes: 6bc6bf8a940a ("dt-bindings: arm: sunxi: document Anbernic RG35XX handheld gaming device variants")
Reviewed-by: Ryan Walklin <ryan@testtoast.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240503154402.967632-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
Pull in remaining commits from 6.10/scsi-queue.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The documentation in one occasion mentions the
VIDIOC_SUBDEV_STREAM_FL_ACTIVE flag. This was meant to be
V4L2_SUBDEV_STREAM_FL_ACTIVE as it's a flag, not an IOCTL. Fix it.
Fixes: cd2c75454d74 ("media: Documentation: Document S_ROUTING behaviour")
Reported-by: Samuel Wein PhD <sam@samwein.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
s/of/off/
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Fixes: e110ba659271 ("docs: netdev: add note about Changes Requested and revising commit messages")
Link: https://lore.kernel.org/r/20240527103618.265801-2-thorsten.blum@toblux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
constraints
The child nodes are missing "additionalProperties" constraints which
means any undocumented properties or child nodes are allowed. Add the
constraints and all the undocumented properties exposed by the fix.
Fixes: f562202fedad ("dt-bindings: net: pse-pd: Add bindings for TPS23881 PSE controller")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240523171750.2837331-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
"additionalProperties" constraints
The child nodes are missing "additionalProperties" constraints which
means any undocumented properties or child nodes are allowed. Add the
constraints, and fix the fallout of wrong manager node regex and
missing properties.
Fixes: 9c1de033afad ("dt-bindings: net: pse-pd: Add bindings for PD692x0 PSE controller")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240523171732.2836880-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c93f261dfc39 ("Documentation/core-api: add swiotlb documentation")
accidentally refers to CONFIG_DYNAMIC_SWIOTLB in one place, while the
config is actually called CONFIG_SWIOTLB_DYNAMIC.
Correct the reference to the intended config option.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Reviewed-by: Petr Tesarik <petr@tesarici.cz>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
properties from cmdline
On x86/ACPI platforms touchscreens mostly just work without needing any
device/model specific configuration. But in some cases (mostly with Silead
and Goodix touchscreens) it is still necessary to manually specify various
touchscreen-properties on a per model basis.
touchscreen_dmi is a special place for DMI quirks for this, but it can be
challenging for users to figure out the right property values, especially
for Silead touchscreens where non of these can be read back from
the touchscreen-controller.
ATM users can only test touchscreen properties by editing touchscreen_dmi.c
and then building a completely new kernel which makes it unnecessary
difficult for users to test and submit properties when necessary for their
laptop / tablet model.
Add support for specifying properties on the kernel commandline to allow
users to easily figure out the right settings. See the added documentation
in kernel-parameters.txt for the commandline syntax.
Cc: Gregor Riepl <onitake@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240523143601.47555-1-hdegoede@redhat.com
|
|
Fix output range, as per datasheet must be -2.5 to 7.5.
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Fixes: b0a96c5f599e ("dt-bindings: iio: dac: Add adi,ad3552r.yaml")
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240503185528.2043127-1-adureghello@baylibre.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
|
|
Pull ceph updates from Ilya Dryomov:
"A series from Xiubo that adds support for additional access checks
based on MDS auth caps which were recently made available to clients.
This is needed to prevent scenarios where the MDS quietly discards
updates that a UID-restricted client previously (wrongfully) acked to
the user.
Other than that, just a documentation fixup"
* tag 'ceph-for-6.10-rc1' of https://github.com/ceph/ceph-client:
doc: ceph: update userspace command to get CephFS metadata
ceph: add CEPHFS_FEATURE_MDS_AUTH_CAPS_CHECK feature bit
ceph: check the cephx mds auth access for async dirop
ceph: check the cephx mds auth access for open
ceph: check the cephx mds auth access for setattr
ceph: add ceph_mds_check_access() helper
ceph: save cap_auths in MDS client when session is opened
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is one new driver and then most of the changes are the device
tree bindings conversions to yaml.
New driver:
- Epson RX8111
Drivers:
- Many Device Tree bindings conversions to dtschema
- pcf8563: wakeup-source support"
* tag 'rtc-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
pcf8563: add wakeup-source support
rtc: rx8111: handle VLOW flag
rtc: rx8111: demote warnings to debug level
rtc: rx6110: Constify struct regmap_config
dt-bindings: rtc: convert trivial devices into dtschema
dt-bindings: rtc: stmp3xxx-rtc: convert to dtschema
dt-bindings: rtc: pxa-rtc: convert to dtschema
rtc: Add driver for Epson RX8111
dt-bindings: rtc: Add Epson RX8111
rtc: mcp795: drop unneeded MODULE_ALIAS
rtc: nuvoton: Modify part number value
rtc: test: Split rtc unit test into slow and normal speed test
dt-bindings: rtc: nxp,lpc1788-rtc: convert to dtschema
dt-bindings: rtc: digicolor-rtc: move to trivial-rtc
dt-bindings: rtc: alphascale,asm9260-rtc: convert to dtschema
dt-bindings: rtc: armada-380-rtc: convert to dtschema
rtc: cros-ec: provide ID table for avoiding fallback match
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more mm updates from Andrew Morton:
"Jeff Xu's implementation of the mseal() syscall"
* tag 'mm-stable-2024-05-24-11-49' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
selftest mm/mseal read-only elf memory segment
mseal: add documentation
selftest mm/mseal memory sealing
mseal: add mseal syscall
mseal: wire up mseal syscall
|
|
Add version string and a header at the beginning of /proc/allocinfo to
allow later format changes. Example output:
> head /proc/allocinfo
allocinfo - version: 1.0
# <size> <calls> <tag info>
0 0 init/main.c:1314 func:do_initcalls
0 0 init/do_mounts.c:353 func:mount_nodev_root
0 0 init/do_mounts.c:187 func:mount_root_generic
0 0 init/do_mounts.c:158 func:do_mount_root
0 0 init/initramfs.c:493 func:unpack_to_rootfs
0 0 init/initramfs.c:492 func:unpack_to_rootfs
0 0 init/initramfs.c:491 func:unpack_to_rootfs
512 1 arch/x86/events/rapl.c:681 func:init_rapl_pmus
128 1 arch/x86/events/rapl.c:571 func:rapl_cpu_online
[akpm@linux-foundation.org: remove stray newline from struct allocinfo_private]
Link: https://lkml.kernel.org/r/20240514163128.3662251-1-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a change to input core to trim amount of keys data in modalias string
in case when a device declares too many keys and they do not fit in
uevent buffer instead of reporting an error which results in uevent
not being generated at all
- support for Machenike G5 Pro Controller added to xpad driver
- support for FocalTech FT5452 and FT8719 added to edt-ft5x06
- support for new SPMI vibrator added to pm8xxx-vibrator driver
- missing locking added to cyapa touchpad driver
- removal of unused fields in various driver structures
- explicit initialization of i2c_device_id::driver_data to 0 dropped
from input drivers
- other assorted fixes and cleanups.
* tag 'input-for-v6.10-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (24 commits)
Input: edt-ft5x06 - add support for FocalTech FT5452 and FT8719
dt-bindings: input: touchscreen: edt-ft5x06: Document FT5452 and FT8719 support
Input: xpad - add support for Machenike G5 Pro Controller
Input: try trimming too long modalias strings
Input: drop explicit initialization of struct i2c_device_id::driver_data to 0
Input: zet6223 - remove an unused field in struct zet6223_ts
Input: chipone_icn8505 - remove an unused field in struct icn8505_data
Input: cros_ec_keyb - remove an unused field in struct cros_ec_keyb
Input: lpc32xx-keys - remove an unused field in struct lpc32xx_kscan_drv
Input: matrix_keypad - remove an unused field in struct matrix_keypad
Input: tca6416-keypad - remove unused struct tca6416_drv_data
Input: tca6416-keypad - remove an unused field in struct tca6416_keypad_chip
Input: da7280 - remove an unused field in struct da7280_haptic
Input: ff-core - prefer struct_size over open coded arithmetic
Input: cyapa - add missing input core locking to suspend/resume functions
input: pm8xxx-vibrator: add new SPMI vibrator support
dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module
input: pm8xxx-vibrator: refactor to support new SPMI vibrator
Input: pm8xxx-vibrator - correct VIB_MAX_LEVELS calculation
Input: sur40 - convert le16 to cpu before use
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes for 6.10-rc1. Most of changes are various
device-specific fixes and quirks, while there are a few small changes
in ALSA core timer and module / built-in fixes"
* tag 'sound-fix-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: fix mute/micmute LEDs don't work for ProBook 440/460 G11.
ALSA: core: Enable proc module when CONFIG_MODULES=y
ALSA: core: Fix NULL module pointer assignment at card init
ALSA: hda/realtek: Enable headset mic of JP-IK LEAP W502 with ALC897
ASoC: dt-bindings: stm32: Ensure compatible pattern matches whole string
ASoC: tas2781: Fix wrong loading calibrated data sequence
ASoC: tas2552: Add TX path for capturing AUDIO-OUT data
ALSA: usb-audio: Fix for sampling rates support for Mbox3
Documentation: sound: Fix trailing whitespaces
ALSA: timer: Set lower bound of start tick time
ASoC: codecs: ES8326: solve hp and button detect issue
ASoC: rt5645: mic-in detection threshold modification
ASoC: Intel: sof_sdw_rt_sdca_jack_common: Use name_prefix for `-sdca` detection
|
|
Add documentation for mseal().
Link: https://lkml.kernel.org/r/20240415163527.626541-5-jeffxu@chromium.org
Signed-off-by: Jeff Xu <jeffxu@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: Jeff Xu <jeffxu@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jorge Lucangeli Obes <jorgelo@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: Stephen Röttger <sroettger@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Amer Al Shanawany <amer.shanawany@gmail.com>
Cc: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The major fix here is for a filesystem corruption issue reported on
Apple M1 as a result of buggy management of the floating point
register state introduced in 6.8. I initially reverted one of the
offending patches, but in the end Ard cooked a proper fix so there's a
revert+reapply in the series.
Aside from that, we've got some CPU errata workarounds and misc other
fixes.
- Fix broken FP register state tracking which resulted in filesystem
corruption when dm-crypt is used
- Workarounds for Arm CPU errata affecting the SSBS Spectre
mitigation
- Fix lockdep assertion in DMC620 memory controller PMU driver
- Fix alignment of BUG table when CONFIG_DEBUG_BUGVERBOSE is
disabled"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/fpsimd: Avoid erroneous elide of user state reload
Reapply "arm64: fpsimd: Implement lazy restore for kernel mode FPSIMD"
arm64: asm-bug: Add .align 2 to the end of __BUG_ENTRY
perf/arm-dmc620: Fix lockdep assert in ->event_init()
Revert "arm64: fpsimd: Implement lazy restore for kernel mode FPSIMD"
arm64: errata: Add workaround for Arm errata 3194386 and 3312417
arm64: cputype: Add Neoverse-V3 definitions
arm64: cputype: Add Cortex-X4 definitions
arm64: barrier: Restore spec_bar() macro
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.10
A bunch of fixes that came in during the merge window, all driver
specific and none of them especially remarkable.
|
|
According to ceph documentation [1], "getfattr -d /some/dir" no longer
displays the list of all extended attributes. Both CephFS kernel and
FUSE clients hide this information.
To retrieve the information you have to specify the particular attribute
name e.g. "getfattr -n ceph.dir.rbytes /some/dir".
[1] https://docs.ceph.com/en/latest/cephfs/quota/
Signed-off-by: Artem Ikonnikov <artem@datacrunch.io>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more non-mm updates from Andrew Morton:
- A series ("kbuild: enable more warnings by default") from Arnd
Bergmann which enables a number of additional build-time warnings. We
fixed all the fallout which we could find, there may still be a few
stragglers.
- Samuel Holland has developed the series "Unified cross-architecture
kernel-mode FPU API". This does a lot of consolidation of
per-architecture kernel-mode FPU usage and enables the use of newer
AMD GPUs on RISC-V.
- Tao Su has fixed some selftests build warnings in the series
"Selftests: Fix compilation warnings due to missing _GNU_SOURCE
definition".
- This pull also includes a nilfs2 fixup from Ryusuke Konishi.
* tag 'mm-nonmm-stable-2024-05-22-17-30' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (23 commits)
nilfs2: make block erasure safe in nilfs_finish_roll_forward()
selftests/harness: use 1024 in place of LINE_MAX
Revert "selftests/harness: remove use of LINE_MAX"
selftests/fpu: allow building on other architectures
selftests/fpu: move FP code to a separate translation unit
drm/amd/display: use ARCH_HAS_KERNEL_FPU_SUPPORT
drm/amd/display: only use hard-float, not altivec on powerpc
riscv: add support for kernel-mode FPU
x86: implement ARCH_HAS_KERNEL_FPU_SUPPORT
powerpc: implement ARCH_HAS_KERNEL_FPU_SUPPORT
LoongArch: implement ARCH_HAS_KERNEL_FPU_SUPPORT
lib/raid6: use CC_FLAGS_FPU for NEON CFLAGS
arm64: crypto: use CC_FLAGS_FPU for NEON CFLAGS
arm64: implement ARCH_HAS_KERNEL_FPU_SUPPORT
ARM: crypto: use CC_FLAGS_FPU for NEON CFLAGS
ARM: implement ARCH_HAS_KERNEL_FPU_SUPPORT
arch: add ARCH_HAS_KERNEL_FPU_SUPPORT
x86/fpu: fix asm/fpu/types.h include guard
kbuild: enable -Wcast-function-type-strict unconditionally
kbuild: enable -Wformat-truncation on clang
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver subsystem updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem updates
for 6.10-rc1. Nothing major here, just lots of new drivers and updates
for apis and new hardware types. Included in here are:
- big IIO driver updates with more devices and drivers added
- fpga driver updates
- hyper-v driver updates
- uio_pruss driver removal, no one uses it, other drivers control the
same hardware now
- binder minor updates
- mhi driver updates
- excon driver updates
- counter driver updates
- accessability driver updates
- coresight driver updates
- other hwtracing driver updates
- nvmem driver updates
- slimbus driver updates
- spmi driver updates
- other smaller misc and char driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (319 commits)
misc: ntsync: mark driver as "broken" to prevent from building
spmi: pmic-arb: Add multi bus support
spmi: pmic-arb: Register controller for bus instead of arbiter
spmi: pmic-arb: Make core resources acquiring a version operation
spmi: pmic-arb: Make the APID init a version operation
spmi: pmic-arb: Fix some compile warnings about members not being described
dt-bindings: spmi: Deprecate qcom,bus-id
dt-bindings: spmi: Add X1E80100 SPMI PMIC ARB schema
spmi: pmic-arb: Replace three IS_ERR() calls by null pointer checks in spmi_pmic_arb_probe()
spmi: hisi-spmi-controller: Do not override device identifier
dt-bindings: spmi: hisilicon,hisi-spmi-controller: clean up example
dt-bindings: spmi: hisilicon,hisi-spmi-controller: fix binding references
spmi: make spmi_bus_type const
extcon: adc-jack: Document missing struct members
extcon: realtek: Remove unused of_gpio.h
extcon: usbc-cros-ec: Convert to platform remove callback returning void
extcon: usb-gpio: Convert to platform remove callback returning void
extcon: max77843: Convert to platform remove callback returning void
extcon: max3355: Convert to platform remove callback returning void
extcon: intel-mrfld: Convert to platform remove callback returning void
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.10-rc1.
Included in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos
instead of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (113 commits)
serial: Clear UPF_DEAD before calling tty_port_register_device_attr_serdev()
serial: imx: Raise TX trigger level to 8
serial: 8250_pnp: Simplify "line" related code
serial: sh-sci: simplify locking when re-issuing RXDMA fails
serial: sh-sci: let timeout timer only run when DMA is scheduled
serial: sh-sci: describe locking requirements for invalidating RXDMA
serial: sh-sci: protect invalidating RXDMA on shutdown
tty: add the option to have a tty reject a new ldisc
serial: core: Call device_set_awake_path() for console port
dt-bindings: serial: brcm,bcm2835-aux-uart: convert to dtschema
tty: serial: uartps: Add support for uartps controller reset
arm64: zynqmp: Add resets property for UART nodes
dt-bindings: serial: cdns,uart: Add optional reset property
serial: 8250_pnp: Switch to DEFINE_SIMPLE_DEV_PM_OPS()
serial: 8250_exar: Keep the includes sorted
serial: 8250_exar: Make type of bit the same in exar_ee_*_bit()
serial: 8250_exar: Use BIT() in exar_ee_read()
serial: 8250_exar: Switch to use dev_err_probe()
serial: 8250_exar: Return directly from switch-cases
serial: 8250_exar: Decrease indentation level
...
|
