| Age | Commit message (Collapse) | Author |
|---|
|
Drop the second snapshot of mmu_invalidate_seq in kvm_faultin_pfn().
Before checking the mismatch of private vs. shared, mmu_invalidate_seq is
saved to fault->mmu_seq, which can be used to detect an invalidation
related to the gfn occurred, i.e. KVM will not install a mapping in page
table if fault->mmu_seq != mmu_invalidate_seq.
Currently there is a second snapshot of mmu_invalidate_seq, which may not
be same as the first snapshot in kvm_faultin_pfn(), i.e. the gfn attribute
may be changed between the two snapshots, but the gfn may be mapped in
page table without hindrance. Therefore, drop the second snapshot as it
has no obvious benefits.
Fixes: f6adeae81f35 ("KVM: x86/mmu: Handle no-slot faults at the beginning of kvm_faultin_pfn()")
Signed-off-by: Tao Su <tao1.su@linux.intel.com>
Message-ID: <20240528102234.2162763-1-tao1.su@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* Fixes and debugging help for the #VE sanity check. Also disable
it by default, even for CONFIG_DEBUG_KERNEL, because it was found
to trigger spuriously (most likely a processor erratum as the
exact symptoms vary by generation).
* Avoid WARN() when two NMIs arrive simultaneously during an NMI-disabled
situation (GIF=0 or interrupt shadow) when the processor supports
virtual NMI. While generally KVM will not request an NMI window
when virtual NMIs are supported, in this case it *does* have to
single-step over the interrupt shadow or enable the STGI intercept,
in order to deliver the latched second NMI.
* Drop support for hand tuning APIC timer advancement from userspace.
Since we have adaptive tuning, and it has proved to work well,
drop the module parameter for manual configuration and with it a
few stupid bugs that it had.
|
|
Remove support for specifying a static local APIC timer advancement value,
and instead present a read-only boolean parameter to let userspace enable
or disable KVM's dynamic APIC timer advancement. Realistically, it's all
but impossible for userspace to specify an advancement that is more
precise than what KVM's adaptive tuning can provide. E.g. a static value
needs to be tuned for the exact hardware and kernel, and if KVM is using
hrtimers, likely requires additional tuning for the exact configuration of
the entire system.
Dropping support for a userspace provided value also fixes several flaws
in the interface. E.g. KVM interprets a negative value other than -1 as a
large advancement, toggling between a negative and positive value yields
unpredictable behavior as vCPUs will switch from dynamic to static
advancement, changing the advancement in the middle of VM creation can
result in different values for vCPUs within a VM, etc. Those flaws are
mostly fixable, but there's almost no justification for taking on yet more
complexity (it's minimal complexity, but still non-zero).
The only arguments against using KVM's adaptive tuning is if a setup needs
a higher maximum, or if the adjustments are too reactive, but those are
arguments for letting userspace control the absolute max advancement and
the granularity of each adjustment, e.g. similar to how KVM provides knobs
for halt polling.
Link: https://lore.kernel.org/all/20240520115334.852510-1-zhoushuling@huawei.com
Cc: Shuling Zhou <zhoushuling@huawei.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240522010304.1650603-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As documented in APM[1], LBR Virtualization must be enabled for SEV-ES
guests. Although KVM currently enforces LBRV for SEV-ES guests, there
are multiple issues with it:
o MSR_IA32_DEBUGCTLMSR is still intercepted. Since MSR_IA32_DEBUGCTLMSR
interception is used to dynamically toggle LBRV for performance reasons,
this can be fatal for SEV-ES guests. For ex SEV-ES guest on Zen3:
[guest ~]# wrmsr 0x1d9 0x4
KVM: entry failed, hardware error 0xffffffff
EAX=00000004 EBX=00000000 ECX=000001d9 EDX=00000000
Fix this by never intercepting MSR_IA32_DEBUGCTLMSR for SEV-ES guests.
No additional save/restore logic is required since MSR_IA32_DEBUGCTLMSR
is of swap type A.
o KVM will disable LBRV if userspace sets MSR_IA32_DEBUGCTLMSR before the
VMSA is encrypted. Fix this by moving LBRV enablement code post VMSA
encryption.
[1]: AMD64 Architecture Programmer's Manual Pub. 40332, Rev. 4.07 - June
2023, Vol 2, 15.35.2 Enabling SEV-ES.
https://bugzilla.kernel.org/attachment.cgi?id=304653
Fixes: 376c6d285017 ("KVM: SVM: Provide support for SEV-ES vCPU creation/loading")
Co-developed-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Message-ID: <20240531044644.768-4-ravi.bangoria@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As documented in APM[1], LBR Virtualization must be enabled for SEV-ES
guests. So, prevent SEV-ES guests when LBRV support is missing.
[1]: AMD64 Architecture Programmer's Manual Pub. 40332, Rev. 4.07 - June
2023, Vol 2, 15.35.2 Enabling SEV-ES.
https://bugzilla.kernel.org/attachment.cgi?id=304653
Fixes: 376c6d285017 ("KVM: SVM: Provide support for SEV-ES vCPU creation/loading")
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Message-ID: <20240531044644.768-3-ravi.bangoria@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM currently allows userspace to read/write MSRs even after the VMSA is
encrypted. This can cause unintentional issues if MSR access has side-
effects. For ex, while migrating a guest, userspace could attempt to
migrate MSR_IA32_DEBUGCTLMSR and end up unintentionally disabling LBRV on
the target. Fix this by preventing access to those MSRs which are context
switched via the VMSA, once the VMSA is encrypted.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Nikunj A Dadhania <nikunj@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Message-ID: <20240531044644.768-2-ravi.bangoria@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When requesting an NMI window, WARN on vNMI support being enabled if and
only if NMIs are actually masked, i.e. if the vCPU is already handling an
NMI. KVM's ABI for NMIs that arrive simultanesouly (from KVM's point of
view) is to inject one NMI and pend the other. When using vNMI, KVM pends
the second NMI simply by setting V_NMI_PENDING, and lets the CPU do the
rest (hardware automatically sets V_NMI_BLOCKING when an NMI is injected).
However, if KVM can't immediately inject an NMI, e.g. because the vCPU is
in an STI shadow or is running with GIF=0, then KVM will request an NMI
window and trigger the WARN (but still function correctly).
Whether or not the GIF=0 case makes sense is debatable, as the intent of
KVM's behavior is to provide functionality that is as close to real
hardware as possible. E.g. if two NMIs are sent in quick succession, the
probability of both NMIs arriving in an STI shadow is infinitesimally low
on real hardware, but significantly larger in a virtual environment, e.g.
if the vCPU is preempted in the STI shadow. For GIF=0, the argument isn't
as clear cut, because the window where two NMIs can collide is much larger
in bare metal (though still small).
That said, KVM should not have divergent behavior for the GIF=0 case based
on whether or not vNMI support is enabled. And KVM has allowed
simultaneous NMIs with GIF=0 for over a decade, since commit 7460fb4a3400
("KVM: Fix simultaneous NMIs"). I.e. KVM's GIF=0 handling shouldn't be
modified without a *really* good reason to do so, and if KVM's behavior
were to be modified, it should be done irrespective of vNMI support.
Fixes: fa4c027a7956 ("KVM: x86: Add support for SVM's Virtual NMI")
Cc: stable@vger.kernel.org
Cc: Santosh Shukla <Santosh.Shukla@amd.com>
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240522021435.1684366-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Force KVM_WERROR if the global WERROR is enabled to avoid pestering the
user about a Kconfig that will ultimately be ignored. Force KVM_WERROR
instead of making it mutually exclusive with WERROR to avoid generating a
.config builds KVM with -Werror, but has KVM_WERROR=n.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240517180341.974251-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Disable KVM's "prove #VE" support by default, as it provides no functional
value, and even its sanity checking benefits are relatively limited. I.e.
it should be fully opt-in even on debug kernels, especially since EPT
Violation #VE suppression appears to be buggy on some CPUs.
Opportunistically add a line in the help text to make it abundantly clear
that KVM_INTEL_PROVE_VE should never be enabled in a production
environment.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Print the SPTEs that correspond to the faulting GPA on an unexpected EPT
Violation #VE to help the user debug failures, e.g. to pinpoint which SPTE
didn't have SUPPRESS_VE set.
Opportunistically assert that the underlying exit reason was indeed an EPT
Violation, as the CPU has *really* gone off the rails if a #VE occurs due
to a completely unexpected exit reason.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Dump the VMCS on an unexpected #VE, otherwise it's practically impossible
to figure out why the #VE occurred.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Assert that KVM doesn't set a SPTE to a value that could trigger an EPT
Violation #VE on a non-MMIO SPTE, e.g. to help detect bugs even without
KVM_INTEL_PROVE_VE enabled, and to help debug actual #VE failures.
Note, this will run afoul of TDX support, which needs to reflect emulated
MMIO accesses into the guest as #VEs (which was the whole point of adding
EPT Violation #VE support in KVM). The obvious fix for that is to exempt
MMIO SPTEs, but that's annoyingly difficult now that is_mmio_spte() relies
on a per-VM value. However, resolving that conundrum is a future problem,
whereas getting KVM_INTEL_PROVE_VE healthy is a current problem.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Always handle #VEs, e.g. due to prove EPT Violation #VE failures, in L0,
as KVM does not expose any #VE capabilities to L1, i.e. any and all #VEs
are KVM's responsibility.
Fixes: 8131cf5b4fd8 ("KVM: VMX: Introduce test mode related to EPT violation VE")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Point vmcs02.VE_INFORMATION_ADDRESS at the vCPU's #VE info page when
initializing vmcs02, otherwise KVM will run L2 with EPT Violation #VE
enabled and a VE info address pointing at pfn 0.
Fixes: 8131cf5b4fd8 ("KVM: VMX: Introduce test mode related to EPT violation VE")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Don't terminate the VM on an unexpected #VE, as it's extremely unlikely
the #VE is fatal to the guest, and even less likely that it presents a
danger to the host. Simply resume the guest on "failure", as the #VE info
page's BUSY field will prevent converting any more EPT Violations to #VEs
for the vCPU (at least, that's what the BUSY field is supposed to do).
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240518000430.1118488-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use SHADOW_NONPRESENT_VALUE when zapping TDP MMU SPTEs with mmu_lock held
for read, tdp_mmu_zap_spte_atomic() was simply missed during the initial
development.
Fixes: 7f01cab84928 ("KVM: x86/mmu: Allow non-zero value for non-present SPTE and removed SPTE")
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
[sean: write changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240518000430.1118488-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- Move a lot of state that was previously stored on a per vcpu basis
into a per-CPU area, because it is only pertinent to the host while
the vcpu is loaded. This results in better state tracking, and a
smaller vcpu structure.
- Add full handling of the ERET/ERETAA/ERETAB instructions in nested
virtualisation. The last two instructions also require emulating
part of the pointer authentication extension. As a result, the trap
handling of pointer authentication has been greatly simplified.
- Turn the global (and not very scalable) LPI translation cache into
a per-ITS, scalable cache, making non directly injected LPIs much
cheaper to make visible to the vcpu.
- A batch of pKVM patches, mostly fixes and cleanups, as the
upstreaming process seems to be resuming. Fingers crossed!
- Allocate PPIs and SGIs outside of the vcpu structure, allowing for
smaller EL2 mapping and some flexibility in implementing more or
less than 32 private IRQs.
- Purge stale mpidr_data if a vcpu is created after the MPIDR map has
been created.
- Preserve vcpu-specific ID registers across a vcpu reset.
- Various minor cleanups and improvements.
LoongArch:
- Add ParaVirt IPI support
- Add software breakpoint support
- Add mmio trace events support
RISC-V:
- Support guest breakpoints using ebreak
- Introduce per-VCPU mp_state_lock and reset_cntx_lock
- Virtualize SBI PMU snapshot and counter overflow interrupts
- New selftests for SBI PMU and Guest ebreak
- Some preparatory work for both TDX and SNP page fault handling.
This also cleans up the page fault path, so that the priorities of
various kinds of fauls (private page, no memory, write to read-only
slot, etc.) are easier to follow.
x86:
- Minimize amount of time that shadow PTEs remain in the special
REMOVED_SPTE state.
This is a state where the mmu_lock is held for reading but
concurrent accesses to the PTE have to spin; shortening its use
allows other vCPUs to repopulate the zapped region while the zapper
finishes tearing down the old, defunct page tables.
- Advertise the max mappable GPA in the "guest MAXPHYADDR" CPUID
field, which is defined by hardware but left for software use.
This lets KVM communicate its inability to map GPAs that set bits
51:48 on hosts without 5-level nested page tables. Guest firmware
is expected to use the information when mapping BARs; this avoids
that they end up at a legal, but unmappable, GPA.
- Fixed a bug where KVM would not reject accesses to MSR that aren't
supposed to exist given the vCPU model and/or KVM configuration.
- As usual, a bunch of code cleanups.
x86 (AMD):
- Implement a new and improved API to initialize SEV and SEV-ES VMs,
which will also be extendable to SEV-SNP.
The new API specifies the desired encryption in KVM_CREATE_VM and
then separately initializes the VM. The new API also allows
customizing the desired set of VMSA features; the features affect
the measurement of the VM's initial state, and therefore enabling
them cannot be done tout court by the hypervisor.
While at it, the new API includes two bugfixes that couldn't be
applied to the old one without a flag day in userspace or without
affecting the initial measurement. When a SEV-ES VM is created with
the new VM type, KVM_GET_REGS/KVM_SET_REGS and friends are rejected
once the VMSA has been encrypted. Also, the FPU and AVX state will
be synchronized and encrypted too.
- Support for GHCB version 2 as applicable to SEV-ES guests.
This, once more, is only accessible when using the new
KVM_SEV_INIT2 flow for initialization of SEV-ES VMs.
x86 (Intel):
- An initial bunch of prerequisite patches for Intel TDX were merged.
They generally don't do anything interesting. The only somewhat
user visible change is a new debugging mode that checks that KVM's
MMU never triggers a #VE virtualization exception in the guest.
- Clear vmcs.EXIT_QUALIFICATION when synthesizing an EPT Misconfig
VM-Exit to L1, as per the SDM.
Generic:
- Use vfree() instead of kvfree() for allocations that always use
vcalloc() or __vcalloc().
- Remove .change_pte() MMU notifier - the changes to non-KVM code are
small and Andrew Morton asked that I also take those through the
KVM tree.
The callback was only ever implemented by KVM (which was also the
original user of MMU notifiers) but it had been nonfunctional ever
since calls to set_pte_at_notify were wrapped with
invalidate_range_start and invalidate_range_end... in 2012.
Selftests:
- Enhance the demand paging test to allow for better reporting and
stressing of UFFD performance.
- Convert the steal time test to generate TAP-friendly output.
- Fix a flaky false positive in the xen_shinfo_test due to comparing
elapsed time across two different clock domains.
- Skip the MONITOR/MWAIT test if the host doesn't actually support
MWAIT.
- Avoid unnecessary use of "sudo" in the NX hugepage test wrapper
shell script, to play nice with running in a minimal userspace
environment.
- Allow skipping the RSEQ test's sanity check that the vCPU was able
to complete a reasonable number of KVM_RUNs, as the assert can fail
on a completely valid setup.
If the test is run on a large-ish system that is otherwise idle,
and the test isn't affined to a low-ish number of CPUs, the vCPU
task can be repeatedly migrated to CPUs that are in deep sleep
states, which results in the vCPU having very little net runtime
before the next migration due to high wakeup latencies.
- Define _GNU_SOURCE for all selftests to fix a warning that was
introduced by a change to kselftest_harness.h late in the 6.9
cycle, and because forcing every test to #define _GNU_SOURCE is
painful.
- Provide a global pseudo-RNG instance for all tests, so that library
code can generate random, but determinstic numbers.
- Use the global pRNG to randomly force emulation of select writes
from guest code on x86, e.g. to help validate KVM's emulation of
locked accesses.
- Allocate and initialize x86's GDT, IDT, TSS, segments, and default
exception handlers at VM creation, instead of forcing tests to
manually trigger the related setup.
Documentation:
- Fix a goof in the KVM_CREATE_GUEST_MEMFD documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (225 commits)
selftests/kvm: remove dead file
KVM: selftests: arm64: Test vCPU-scoped feature ID registers
KVM: selftests: arm64: Test that feature ID regs survive a reset
KVM: selftests: arm64: Store expected register value in set_id_regs
KVM: selftests: arm64: Rename helper in set_id_regs to imply VM scope
KVM: arm64: Only reset vCPU-scoped feature ID regs once
KVM: arm64: Reset VM feature ID regs from kvm_reset_sys_regs()
KVM: arm64: Rename is_id_reg() to imply VM scope
KVM: arm64: Destroy mpidr_data for 'late' vCPU creation
KVM: arm64: Use hVHE in pKVM by default on CPUs with VHE support
KVM: arm64: Fix hvhe/nvhe early alias parsing
KVM: SEV: Allow per-guest configuration of GHCB protocol version
KVM: SEV: Add GHCB handling for termination requests
KVM: SEV: Add GHCB handling for Hypervisor Feature Support requests
KVM: SEV: Add support to handle AP reset MSR protocol
KVM: x86: Explicitly zero kvm_caps during vendor module load
KVM: x86: Fully re-initialize supported_mce_cap on vendor module load
KVM: x86: Fully re-initialize supported_vm_types on vendor module load
KVM: x86/mmu: Sanity check that __kvm_faultin_pfn() doesn't create noslot pfns
KVM: x86/mmu: Initialize kvm_page_fault's pfn and hva to error values
...
|
|
KVM x86 misc changes for 6.10:
- Advertise the max mappable GPA in the "guest MAXPHYADDR" CPUID field, which
is unused by hardware, so that KVM can communicate its inability to map GPAs
that set bits 51:48 due to lack of 5-level paging. Guest firmware is
expected to use the information to safely remap BARs in the uppermost GPA
space, i.e to avoid placing a BAR at a legal, but unmappable, GPA.
- Use vfree() instead of kvfree() for allocations that always use vcalloc()
or __vcalloc().
- Don't completely ignore same-value writes to immutable feature MSRs, as
doing so results in KVM failing to reject accesses to MSR that aren't
supposed to exist given the vCPU model and/or KVM configuration.
- Don't mark APICv as being inhibited due to ABSENT if APICv is disabled
KVM-wide to avoid confusing debuggers (KVM will never bother clearing the
ABSENT inhibit, even if userspace enables in-kernel local APIC).
|
|
KVM x86 MMU changes for 6.10:
- Process TDP MMU SPTEs that are are zapped while holding mmu_lock for read
after replacing REMOVED_SPTE with '0' and flushing remote TLBs, which allows
vCPU tasks to repopulate the zapped region while the zapper finishes tearing
down the old, defunct page tables.
- Fix a longstanding, likely benign-in-practice race where KVM could fail to
detect a write from kvm_mmu_track_write() to a shadowed GPTE if the GPTE is
first page table being shadowed.
|
|
KVM VMX changes for 6.10:
- Clear vmcs.EXIT_QUALIFICATION when synthesizing an EPT Misconfig VM-Exit to
L1, as per the SDM.
- Move kvm_vcpu_arch's exit_qualification into x86_exception, as the field is
used only when synthesizing nested EPT violation, i.e. it's not the vCPU's
"real" exit_qualification, which is tracked elsewhere.
- Add a sanity check to assert that EPT Violations are the only sources of
nested PML Full VM-Exits.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson into HEAD
LoongArch KVM changes for v6.10
1. Add ParaVirt IPI support.
2. Add software breakpoint support.
3. Add mmio trace events support.
|
|
While the main additions from GHCB protocol version 1 to version 2
revolve mostly around SEV-SNP support, there are a number of changes
applicable to SEV-ES guests as well. Pluck a handful patches from the
SNP hypervisor patchset for GHCB-related changes that are also applicable
to SEV-ES. A KVM_SEV_INIT2 field lets userspace can control the maximum
GHCB protocol version advertised to guests and manage compatibility
across kernels/versions.
|
|
A combination of prep work for TDX and SNP, and a clean up of the
page fault path to (hopefully) make it easier to follow the rules for
private memory, noslot faults, writes to read-only slots, etc.
|
|
Allow a non-zero value for non-present SPTE and removed SPTE,
so that TDX can set the "suppress VE" bit.
|
|
The GHCB protocol version may be different from one guest to the next.
Add a field to track it for each KVM instance and extend KVM_SEV_INIT2
to allow it to be configured by userspace.
Now that all SEV-ES support for GHCB protocol version 2 is in place, go
ahead and default to it when creating SEV-ES guests through the new
KVM_SEV_INIT2 interface. Keep the older KVM_SEV_ES_INIT interface
restricted to GHCB protocol version 1.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240501071048.2208265-5-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
GHCB version 2 adds support for a GHCB-based termination request that
a guest can issue when it reaches an error state and wishes to inform
the hypervisor that it should be terminated. Implement support for that
similarly to GHCB MSR-based termination requests that are already
available to SEV-ES guests via earlier versions of the GHCB protocol.
See 'Termination Request' in the 'Invoking VMGEXIT' section of the GHCB
specification for more details.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240501071048.2208265-4-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Version 2 of the GHCB specification introduced advertisement of features
that are supported by the Hypervisor.
Now that KVM supports version 2 of the GHCB specification, bump the
maximum supported protocol version.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240501071048.2208265-3-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add support for AP Reset Hold being invoked using the GHCB MSR protocol,
available in version 2 of the GHCB specification.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240501071048.2208265-2-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Zero out all of kvm_caps when loading a new vendor module to ensure that
KVM can't inadvertently rely on global initialization of a field, and add
a comment above the definition of kvm_caps to call out that all fields
needs to be explicitly computed during vendor module load.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240423165328.2853870-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Effectively reset supported_mce_cap on vendor module load to ensure that
capabilities aren't unintentionally preserved across module reload, e.g.
if kvm-intel.ko added a module param to control LMCE support, or if
someone somehow managed to load a vendor module that doesn't support LMCE
after loading and unloading kvm-intel.ko.
Practically speaking, this bug is a non-issue as kvm-intel.ko doesn't have
a module param for LMCE, and there is no system in the world that supports
both kvm-intel.ko and kvm-amd.ko.
Fixes: c45dcc71b794 ("KVM: VMX: enable guest access to LMCE related MSRs")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240423165328.2853870-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Recompute the entire set of supported VM types when a vendor module is
loaded, as preserving supported_vm_types across vendor module unload and
reload can result in VM types being incorrectly treated as supported.
E.g. if a vendor module is loaded with TDP enabled, unloaded, and then
reloaded with TDP disabled, KVM_X86_SW_PROTECTED_VM will be incorrectly
retained. Ditto for SEV_VM and SEV_ES_VM and their respective module
params in kvm-amd.ko.
Fixes: 2a955c4db1dd ("KVM: x86: Add supported_vm_types to kvm_caps")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240423165328.2853870-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
WARN if __kvm_faultin_pfn() generates a "no slot" pfn, and gracefully
handle the unexpected behavior instead of continuing on with dangerous
state, e.g. tdp_mmu_map_handle_target_level() _only_ checks fault->slot,
and so could install a bogus PFN into the guest.
The existing code is functionally ok, because kvm_faultin_pfn() pre-checks
all of the cases that result in KVM_PFN_NOSLOT, but it is unnecessarily
unsafe as it relies on __gfn_to_pfn_memslot() getting the _exact_ same
memslot, i.e. not a re-retrieved pointer with KVM_MEMSLOT_INVALID set.
And checking only fault->slot would fall apart if KVM ever added a flag or
condition that forced emulation, similar to how KVM handles writes to
read-only memslots.
Cc: David Matlack <dmatlack@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-17-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Explicitly set "pfn" and "hva" to error values in kvm_mmu_do_page_fault()
to harden KVM against using "uninitialized" values. In quotes because the
fields are actually zero-initialized, and zero is a legal value for both
page frame numbers and virtual addresses. E.g. failure to set "pfn" prior
to creating an SPTE could result in KVM pointing at physical address '0',
which is far less desirable than KVM generating a SPTE with reserved PA
bits set and thus effectively killing the VM.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-16-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Explicitly set fault->hva to KVM_HVA_ERR_BAD when handling a "no slot"
fault to ensure that KVM doesn't use a bogus virtual address, e.g. if
there *was* a slot but it's unusable (APIC access page), or if there
really was no slot, in which case fault->hva will be '0' (which is a
legal address for x86).
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-15-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Handle the "no memslot" case at the beginning of kvm_faultin_pfn(), just
after the private versus shared check, so that there's no need to
repeatedly query whether or not a slot exists. This also makes it more
obvious that, except for private vs. shared attributes, the process of
faulting in a pfn simply doesn't apply to gfns without a slot.
Opportunistically stuff @fault's metadata in kvm_handle_noslot_fault() so
that it doesn't need to be duplicated in all paths that invoke
kvm_handle_noslot_fault(), and to minimize the probability of not stuffing
the right fields.
Leave the existing handle behind, but convert it to a WARN, to guard
against __kvm_faultin_pfn() unexpectedly nullifying fault->slot.
Cc: David Matlack <dmatlack@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-14-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the checks related to the validity of an access to a memslot from the
inner __kvm_faultin_pfn() to its sole caller, kvm_faultin_pfn(). This
allows emulating accesses to the APIC access page, which don't need to
resolve a pfn, even if there is a relevant in-progress mmu_notifier
invalidation. Ditto for accesses to KVM internal memslots from L2, which
KVM also treats as emulated MMIO.
More importantly, this will allow for future cleanup by having the
"no memslot" case bail from kvm_faultin_pfn() very early on.
Go to rather extreme and gross lengths to make the change a glorified
nop, e.g. call into __kvm_faultin_pfn() even when there is no slot, as the
related code is very subtle. E.g. fault->slot can be nullified if it
points at the APIC access page, some flows in KVM x86 expect fault->pfn
to be KVM_PFN_NOSLOT, while others check only fault->slot, etc.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-13-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Explicitly detect and disallow private accesses to emulated MMIO in
kvm_handle_noslot_fault() instead of relying on kvm_faultin_pfn_private()
to perform the check. This will allow the page fault path to go straight
to kvm_handle_noslot_fault() without bouncing through __kvm_faultin_pfn().
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240228024147.41573-12-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Allow mapping KVM's internal memslots used for EPT without unrestricted
guest into L2, i.e. allow mapping the hidden TSS and the identity mapped
page tables into L2. Unlike the APIC access page, there is no correctness
issue with letting L2 access the "hidden" memory. Allowing these memslots
to be mapped into L2 fixes a largely theoretical bug where KVM could
incorrectly emulate subsequent _L1_ accesses as MMIO, and also ensures
consistent KVM behavior for L2.
If KVM is using TDP, but L1 is using shadow paging for L2, then routing
through kvm_handle_noslot_fault() will incorrectly cache the gfn as MMIO,
and create an MMIO SPTE. Creating an MMIO SPTE is ok, but only because
kvm_mmu_page_role.guest_mode ensure KVM uses different roots for L1 vs.
L2. But vcpu->arch.mmio_gfn will remain valid, and could cause KVM to
incorrectly treat an L1 access to the hidden TSS or identity mapped page
tables as MMIO.
Furthermore, forcing L2 accesses to be treated as "no slot" faults doesn't
actually prevent exposing KVM's internal memslots to L2, it simply forces
KVM to emulate the access. In most cases, that will trigger MMIO,
amusingly due to filling vcpu->arch.mmio_gfn, but also because
vcpu_is_mmio_gpa() unconditionally treats APIC accesses as MMIO, i.e. APIC
accesses are ok. But the hidden TSS and identity mapped page tables could
go either way (MMIO or access the private memslot's backing memory).
Alternatively, the inconsistent emulator behavior could be addressed by
forcing MMIO emulation for L2 access to all internal memslots, not just to
the APIC. But that's arguably less correct than letting L2 access the
hidden TSS and identity mapped page tables, not to mention that it's
*extremely* unlikely anyone cares what KVM does in this case. From L1's
perspective there is R/W memory at those memslots, the memory just happens
to be initialized with non-zero data. Making the memory disappear when it
is accessed by L2 is far more magical and arbitrary than the memory
existing in the first place.
The APIC access page is special because KVM _must_ emulate the access to
do the right thing (emulate an APIC access instead of reading/writing the
APIC access page). And despite what commit 3a2936dedd20 ("kvm: mmu: Don't
expose private memslots to L2") said, it's not just necessary when L1 is
accelerating L2's virtual APIC, it's just as important (likely *more*
imporant for correctness when L1 is passing through its own APIC to L2.
Fixes: 3a2936dedd20 ("kvm: mmu: Don't expose private memslots to L2")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-11-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Prioritize private vs. shared gfn attribute checks above slot validity
checks to ensure a consistent userspace ABI. E.g. as is, KVM will exit to
userspace if there is no memslot, but emulate accesses to the APIC access
page even if the attributes mismatch.
Fixes: 8dd2eee9d526 ("KVM: x86/mmu: Handle page fault for private memory")
Cc: Yu Zhang <yu.c.zhang@linux.intel.com>
Cc: Chao Peng <chao.p.peng@linux.intel.com>
Cc: Fuad Tabba <tabba@google.com>
Cc: Michael Roth <michael.roth@amd.com>
Cc: Isaku Yamahata <isaku.yamahata@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
WARN and skip the emulated MMIO fastpath if a private, reserved page fault
is encountered, as private+reserved should be an impossible combination
(KVM should never create an MMIO SPTE for a private access).
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240228024147.41573-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Right now the error code is not used when an async page fault is completed.
This is not a problem in the current code, but it is untidy. For protected
VMs, we will also need to check that the page attributes match the current
state of the page, because asynchronous page faults can only occur on
shared pages (private pages go through kvm_faultin_pfn_private() instead of
__gfn_to_pfn_memslot()).
Start by piping the error code from kvm_arch_setup_async_pf() to
kvm_arch_async_page_ready() via the architecture-specific async page
fault data. For now, it can be used to assert that there are no
async page faults on private memory.
Extracted from a patch by Isaku Yamahata.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add and use a synthetic, KVM-defined page fault error code to indicate
whether a fault is to private vs. shared memory. TDX and SNP have
different mechanisms for reporting private vs. shared, and KVM's
software-protected VMs have no mechanism at all. Usurp an error code
flag to avoid having to plumb another parameter to kvm_mmu_page_fault()
and friends.
Alternatively, KVM could borrow AMD's PFERR_GUEST_ENC_MASK, i.e. set it
for TDX and software-protected VMs as appropriate, but that would require
*clearing* the flag for SEV and SEV-ES VMs, which support encrypted
memory at the hardware layer, but don't utilize private memory at the
KVM layer.
Opportunistically add a comment to call out that the logic for software-
protected VMs is (and was before this commit) broken for nested MMUs, i.e.
for nested TDP, as the GPA is an L2 GPA. Punt on trying to play nice with
nested MMUs as there is a _lot_ of functionality that simply doesn't work
for software-protected VMs, e.g. all of the paths where KVM accesses guest
memory need to be updated to be aware of private vs. shared memory.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20240228024147.41573-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
WARN if bits 63:32 are non-zero when handling an intercepted legacy #PF,
as the error code for #PF is limited to 32 bits (and in practice, 16 bits
on Intel CPUS). This behavior is architectural, is part of KVM's ABI
(see kvm_vcpu_events.error_code), and is explicitly documented as being
preserved for intecerpted #PF in both the APM:
The error code saved in EXITINFO1 is the same as would be pushed onto
the stack by a non-intercepted #PF exception in protected mode.
and even more explicitly in the SDM as VMCS.VM_EXIT_INTR_ERROR_CODE is a
32-bit field.
Simply drop the upper bits if hardware provides garbage, as spurious
information should do no harm (though in all likelihood hardware is buggy
and the kernel is doomed).
Handling all upper 32 bits in the #PF path will allow moving the sanity
check on synthetic checks from kvm_mmu_page_fault() to npf_interception(),
which in turn will allow deriving PFERR_PRIVATE_ACCESS from AMD's
PFERR_GUEST_ENC_MASK without running afoul of the sanity check.
Note, this is also why Intel uses bit 15 for SGX (highest bit on Intel CPUs)
and AMD uses bit 31 for RMP (highest bit on AMD CPUs); using the highest
bit minimizes the probability of a collision with the "other" vendor,
without needing to plumb more bits through microcode.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240228024147.41573-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Plumb the full 64-bit error code throughout the page fault handling code
so that KVM can use the upper 32 bits, e.g. SNP's PFERR_GUEST_ENC_MASK
will be used to determine whether or not a fault is private vs. shared.
Note, passing the 64-bit error code to FNAME(walk_addr)() does NOT change
the behavior of permission_fault() when invoked in the page fault path, as
KVM explicitly clears PFERR_IMPLICIT_ACCESS in kvm_mmu_page_fault().
Continue passing '0' from the async #PF worker, as guest_memfd and thus
private memory doesn't support async page faults.
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
[mdr: drop references/changes on rebase, update commit message]
Signed-off-by: Michael Roth <michael.roth@amd.com>
[sean: drop truncation in call to FNAME(walk_addr)(), rewrite changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-ID: <20240228024147.41573-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the sanity check that hardware never sets bits that collide with KVM-
define synthetic bits from kvm_mmu_page_fault() to npf_interception(),
i.e. make the sanity check #NPF specific. The legacy #PF path already
WARNs if _any_ of bits 63:32 are set, and the error code that comes from
VMX's EPT Violatation and Misconfig is 100% synthesized (KVM morphs VMX's
EXIT_QUALIFICATION into error code flags).
Add a compile-time assert in the legacy #PF handler to make sure that KVM-
define flags are covered by its existing sanity check on the upper bits.
Opportunistically add a description of PFERR_IMPLICIT_ACCESS, since we
are removing the comment that defined it.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@linux.intel.com>
Message-ID: <20240228024147.41573-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Open code the bit number directly in the PFERR_* masks and drop the
intermediate PFERR_*_BIT defines, as having to bounce through two macros
just to see which flag corresponds to which bit is quite annoying, as is
having to define two macros just to add recognition of a new flag.
Use ternary operator to derive the bit in permission_fault(), the one
function that actually needs the bit number as part of clever shifting
to avoid conditional branches. Generally the compiler is able to turn
it into a conditional move, and if not it's not really a big deal.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240228024147.41573-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Exit to userspace with -EFAULT / KVM_EXIT_MEMORY_FAULT if a private fault
triggers emulation of any kind, as KVM doesn't currently support emulating
access to guest private memory. Practically speaking, private faults and
emulation are already mutually exclusive, but there are many flow that
can result in KVM returning RET_PF_EMULATE, and adding one last check
to harden against weird, unexpected combinations and/or KVM bugs is
inexpensive.
Suggested-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20240228024147.41573-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The kvm_pi_irte_update tracepoint is called from both SVM and VMX vendor
code, and while the "posted interrupt" naming is also adopted by SVM in
several places, VT-d specifically refers to Intel's "Virtualization
Technology for Directed I/O".
Signed-off-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Link: https://lore.kernel.org/r/20240418021823.1275276-3-alejandro.j.jimenez@oracle.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Use the APICv enablement status to determine if APICV_INHIBIT_REASON_ABSENT
needs to be set, instead of unconditionally setting the reason during
initialization.
Specifically, in cases where AVIC is disabled via module parameter or lack
of hardware support, unconditionally setting an inhibit reason due to the
absence of an in-kernel local APIC can lead to a scenario where the reason
incorrectly remains set after a local APIC has been created by either
KVM_CREATE_IRQCHIP or the enabling of KVM_CAP_IRQCHIP_SPLIT. This is
because the helpers in charge of removing the inhibit return early if
enable_apicv is not true, and therefore the bit remains set.
This leads to confusion as to the cause why APICv is not active, since an
incorrect reason will be reported by tracepoints and/or a debugging tool
that examines the currently set inhibit reasons.
Fixes: ef8b4b720368 ("KVM: ensure APICv is considered inactive if there is no APIC")
Signed-off-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Link: https://lore.kernel.org/r/20240418021823.1275276-2-alejandro.j.jimenez@oracle.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
