| Age | Commit message (Collapse) | Author |
|---|
|
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd6183 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf1675 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.
Fixes: a1ea57710c9d ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240517050121.2174412-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before DCB support, the KSZ driver had only PCP as source of packet
priority values. To avoid regressions, make PCP only as default value.
User will need enable DSCP support manually.
This patch do not affect other KSZ8 related quirks. User will still be
warned by setting not support configurations for the port 2.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All other functions are commented. Add missing comments to following
functions:
ksz_set_global_dscp_entry()
ksz_port_add_dscp_prio()
ksz_port_del_dscp_prio()
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509065023.3033397-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8xxx variants
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a separate phylink_mac_ops for the KSZ8830 chip-id.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1s0O7R-009gq2-Qm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1s0O7M-009gpw-Lj@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7H-009gpq-IF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7C-009gpk-Dh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ID table already has respective entry and MODULE_DEVICE_TABLE and
creates proper alias for SPI driver. Having another MODULE_ALIAS causes
the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240414154929.127045-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add check for unsupported control flags.
Only compile-tested, no access to HW.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
0 entries
We already have a variable to provide number of entries. So use it,
instead of using error number.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-9-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
got any
The read/write path may fail. So, return error if we got it.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
timeout
EAGAIN was not used by previous code and not used by current code. So,
remove it and use proper error value.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use 'ret' instead of 'rc' in ksz8_r_dyn_mac_table() to maintain
consistency with the rest of the file.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the code out of a long if statement scope in ksz8_r_dyn_mac_table()
to improve code readability.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor ksz8_fdb_dump() to address potential issues:
- Limit the number of iterations to avoid endless loops.
- Handle error codes returned by ksz8_r_dyn_mac_table(), with
an exception for -ENXIO when no more dynamic entries are detected.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz8_r_dyn_mac_table() is not used outside the source file. Make it
static.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ksz8_r_dyn_mac_table()
The FDB timestamps are not being utilized. This commit removes the
unused timestamp support from ksz8_r_dyn_mac_table() function.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240403125039.3414824-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Core in spi_register_driver() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240330211023.100924-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Merge in late fixes to prepare for the 6.9 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
soft reset
This driver has two separate reset sequence in different places:
- gpio/HW reset on start of ksz_switch_register()
- SW reset on start of ksz_setup()
The second one will overwrite drive strength configuration made in the
ksz_switch_register().
To fix it, move ksz_parse_drive_strength() from ksz_switch_register() to
ksz_setup().
Fixes: d67d7247f641 ("net: dsa: microchip: Add drive strength configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240304135612.814404-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/page_pool_user.c
0b11b1c5c320 ("netdev: let netlink core handle -EMSGSIZE errors")
429679dcf7d9 ("page_pool: fix netlink dump stop/resume")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This bug was noticed while re-implementing parts of the kernel
driver in userspace using spidev. The goal was to enable some
of the errata workarounds that Microchip describes in their
errata sheet [1].
Both the errata sheet and the regular datasheet of e.g. the KSZ8795
imply that you need to do this for indirect register accesses:
- write a 16-bit value to a control register pair (this value
consists of the indirect register table, and the offset inside
the table)
- either read or write an 8-bit value from the data storage
register (indicated by REG_IND_BYTE in the kernel)
The current implementation has the order swapped. It can be
proven, by reading back some indirect register with known content
(the EEE register modified in ksz8_handle_global_errata() is one of
these), that this implementation does not work.
Private discussion with Oleksij Rempel of Pengutronix has revealed
that the workaround was apparantly never tested on actual hardware.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/Errata/KSZ87xx-Errata-DS80000687C.pdf
Signed-off-by: Tobias Jakobi (Compleo) <tobias.jakobi.compleo@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 7b6e6235b664 ("net: dsa: microchip: ksz8795: handle eee specif erratum")
Link: https://lore.kernel.org/r/20240304154135.161332-1-tobias.jakobi.compleo@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8873
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the use of define DSA_TAG_PROTO_LAN937X_VALUE to
DSA_TAG_PROTO_LAN937X to improve readability.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20231206160124.1935451-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/stmicro/stmmac/dwmac5.c
drivers/net/ethernet/stmicro/stmmac/dwmac5.h
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c
drivers/net/ethernet/stmicro/stmmac/hwif.h
37e4b8df27bc ("net: stmmac: fix FPE events losing")
c3f3b97238f6 ("net: stmmac: Refactor EST implementation")
https://lore.kernel.org/all/20231206110306.01e91114@canb.auug.org.au/
Adjacent changes:
net/ipv4/tcp_ao.c
9396c4ee93f9 ("net/tcp: Don't store TCP-AO maclen on reqsk")
7b0f570f879a ("tcp: Move TCP-AO bits from cookie_v[46]_check() to tcp_ao_syncookie().")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.
When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.
This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8
Fixes: ab32f56a4100 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With the ksz_chip_id enums moved to the platform include file for ksz
switches, platform code that instantiates a device can now use these to
set ksz_platform_data::chip_id.
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ksz driver has bits and pieces of platform_data probing support, but
it doesn't work.
The conventional thing to do is to have an encapsulating structure for
struct dsa_chip_data that gets put into dev->platform_data. This driver
expects a struct ksz_platform_data, but that doesn't contain a struct
dsa_chip_data as first element, which will obviously not work with
dsa_switch_probe() -> dsa_switch_parse().
Pointing dev->platform_data to a struct dsa_chip_data directly is in
principle possible, but that doesn't work either. The driver has
ksz_switch_detect() to read the device ID from hardware, followed by
ksz_check_device_id() to compare it against a predetermined expected
value. This protects against early errors in the SPI/I2C communication.
With platform_data, the mechanism in ksz_check_device_id() doesn't work
and even leads to NULL pointer dereferences, since of_device_get_match_data()
doesn't work in that probe path.
So obviously, the platform_data support is actually missing, and the
existing handling of struct ksz_platform_data is bogus. Complete the
support by adding a struct dsa_chip_data as first element, and fixing up
ksz_check_device_id() to pick up the platform_data instead of the
unavailable of_device_get_match_data().
The early dev->chip_id assignment from ksz_switch_register() is also
bogus, because ksz_switch_detect() sets it to an initial value. So
remove it.
Also, ksz_platform_data :: enabled_ports isn't used anywhere, delete it.
Link: https://lore.kernel.org/netdev/20231204154315.3906267-1-dd@embedd.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microchip KSZ8863/KSZ8873 have the ability to select between internal
and external RMII reference clock. By default, reference clock
needs to be provided via REFCLKI_3 pin. If required, device can be
setup to provide RMII clock internally so that REFCLKI_3 pin can be
left unconnected.
Add a new "microchip,rmii-clk-internal" property which will set
RMII clock reference to internal. If property is not set, reference
clock needs to be provided externally.
While at it, move the ksz8795_cpu_interface_select() to
ksz8_config_cpu_port() to get a cleaner call path for cpu port.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Last part of the driver do now support phylink_mac_link_up(). So, make it
not optional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
