| Age | Commit message (Collapse) | Author |
|---|
|
The only user of blk_revalidate_disk_zones() second argument was the
SCSI disk driver (sd). Now that this driver does not require this
update_driver_data argument, remove it to simplify the interface of
blk_revalidate_disk_zones(). Also update the function kdoc comment to
be more accurate (i.e. there is no gendisk ->revalidate method).
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-21-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set the request queue of a TYPE_ZBC device as needing zone append
emulation by setting the device queue max_zone_append_sectors limit to
0. This enables the block layer generic implementation provided by zone
write plugging. With this, the sd driver will never see a
REQ_OP_ZONE_APPEND request and the zone append emulation code
implemented in sd_zbc.c can be removed.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Tested-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20240408014128.205141-14-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When zones were first added the SCSI and ATA specs, two different
models were supported (in addition to the drive managed one that
is invisible to the host):
- host managed where non-conventional zones there is strict requirement
to write at the write pointer, or else an error is returned
- host aware where a write point is maintained if writes always happen
at it, otherwise it is left in an under-defined state and the
sequential write preferred zones behave like conventional zones
(probably very badly performing ones, though)
Not surprisingly this lukewarm model didn't prove to be very useful and
was finally removed from the ZBC and SBC specs (NVMe never implemented
it). Due to to the easily disappearing write pointer host software
could never rely on the write pointer to actually be useful for say
recovery.
Fortunately only a few HDD prototypes shipped using this model which
never made it to mass production. Drop the support before it is too
late. Note that any such host aware prototype HDD can still be used
with Linux as we'll now treat it as a conventional HDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231217165359.604246-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In sd_zbc_revalidate_zones(), execute blk_queue_chunk_sectors() and
blk_queue_max_zone_append_sectors() to respectively set a ZBC device
zone size and maximum zone append sector limit before executing
blk_revalidate_disk_zones(). This is to allow the block layer zone
reavlidation to check these device characteristics prior to checking all
zones of the device.
Since blk_queue_max_zone_append_sectors() already caps the device
maximum zone append limit to the zone size and to the maximum command
size, the max_append value passed to blk_queue_max_zone_append_sectors()
is simplified to the maximum number of segments times the number of
sectors per page.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230703024812.76778-2-dlemoal@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use PAGE_SECTORS_SHIFT instead of open-coding it.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20230613-sd_zbc-page_sectors-v1-1-363460a4413d@wdc.com
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the sd driver revalidates host-managed SMR disks, it calls
disk_set_zoned() which changes the zone_write_granularity attribute value
to the logical block size regardless of the device type. After that, the sd
driver overwrites the value in sd_zbc_read_zone() with the physical block
size, since ZBC/ZAC requires this for host-managed disks. Between the calls
to disk_set_zoned() and sd_zbc_read_zone(), there exists a window where the
attribute shows the logical block size as the zone_write_granularity value,
which is wrong for host-managed disks. The duration of the window is from
20ms to 200ms, depending on report zone command execution time.
To avoid the wrong zone_write_granularity value between disk_set_zoned()
and sd_zbc_read_zone(), modify the value not in sd_zbc_read_zone() but
just after disk_set_zoned() call.
Fixes: a805a4fa4fa3 ("block: introduce zone_write_granularity limit")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230306063024.3376959-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
scsi_execute_req() is going to be removed. Conver zbc to
scsi_execute_cmd().
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add tracepoints to the SCSI zone append emulation in order to trace the
zone start to write-pointer aligned LBA translation and the corresponding
completion.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/d103bcf5f90139143469f2a0084c74bd9e03ad4a.1669804487.git.johannes.thumshirn@wdc.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE(16) for
host-managed zoned block devices, but does not mandate SYNCHRONIZE
CACHE(10). Call SYNCHRONIZE CACHE(16) in place of SYNCHRONIZE CACHE(10) to
ensure that the command is always supported. For this purpose, add
use_16_for_sync flag to struct scsi_device in same manner as use_16_for_rw
flag.
To be precise, ZBC does not mandate SYNCHRONIZE CACHE(16) for host-aware
zoned block devices. However, modern devices should support 16-byte
commands. Hence, call SYNCHRONIZE CACHE (16) on both types of ZBC devices,
host-aware and host-managed. Of note is that READ(16) and WRITE(16) have
same story and they are already called for both types of ZBC devices.
Another note is that this patch depends on the fix commit ea045fd344cb
("ata: libata-scsi: fix SYNCHRONIZE CACHE (16) command failure").
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20221115002905.1709006-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opendource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The type name enum req_opf is misleading since it suggests that values of
this type include both an operation type and flags. Since values of this
type represent an operation only, change the type name into enum req_op.
Convert the enum req_op documentation into kernel-doc format. Move a few
definitions such that the enum req_op documentation occurs just above
the enum req_op definition.
The name "req_opf" was introduced by commit ef295ecf090d ("block: better op
and flags encoding").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move the zone related fields that are currently stored in
struct request_queue to struct gendisk as these are part of the highlevel
block layer API and are only used for non-passthrough I/O that requires
the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Switch to a gendisk based API in preparation for moving all zone related
fields from the request_queue to the gendisk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-11-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Prepare for storing the zone related field in struct gendisk instead
of struct request_queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-7-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Make sure to always free a scsi disk zone information, even for regular
disks. This ensures that there is no memory leak, even in the case of a
zoned disk changing type to a regular disk (e.g. with a reformat using the
FORMAT WITH PRESET command or other vendor proprietary command).
To do this, rename sd_zbc_clear_zone_info() to sd_zbc_free_zone_info() and
remove sd_zbc_release_disk(). A call to sd_zbc_free_zone_info() is added to
sd_zbc_read_zones() for drives for which sd_is_zoned() returns
false. Furthermore, sd_zbc_free_zone_info() code make s sure that the sdkp
rev_mutex is never used while not being initialized by gating the cleanup
code with a a check on the zone_wp_update_buf field as it is never NULL
when rev_mutex has been initialized.
Link: https://lore.kernel.org/r/20220601062544.905141-3-damien.lemoal@opensource.wdc.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ZBC-2 allows host-managed disks to report gap zones. This allow zoned disks
to report an offset between data zone starts that is a power of two even if
the number of logical blocks with data per zone is not a power of two.
Another new feature in ZBC-2 is support for constant zone starting LBA
offsets. For zoned disks that report a constant zone starting LBA offset,
hide the gap zones from the block layer. Report the offset between data
zone starts as zone size and report the number of logical blocks with data
per zone as the zone capacity.
Link: https://lore.kernel.org/r/20220421183023.3462291-7-bvanassche@acm.org
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
[ bvanassche: Reworked this patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return early in sd_zbc_check_zoned_characteristics() for host-aware
disks. This patch does not change any functionality but makes a later patch
easier to read.
Link: https://lore.kernel.org/r/20220421183023.3462291-6-bvanassche@acm.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
[ bvanassche: extracted this change from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Deriving the meaning of the nr_zones, rev_nr_zones, zone_blocks and
rev_zone_blocks member variables requires careful analysis of the source
code. Make the meaning of these member variables easier to understand by
introducing struct zoned_disk_info.
Link: https://lore.kernel.org/r/20220421183023.3462291-5-bvanassche@acm.org
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When querying zones, track the position in logical blocks instead of in
sectors. This change slightly simplifies sd_zbc_report_zones().
Link: https://lore.kernel.org/r/20220421183023.3462291-4-bvanassche@acm.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
[ bvanassche: extracted this change from a larger patch ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following check in sd_zbc_cmnd_checks() can only work correctly if the
zone size is a power of two:
if (sector & (sd_zbc_zone_sectors(sdkp) - 1))
/* Unaligned request */
return BLK_STS_IOERR;
Hence this patch that verifies that the zone size is a power of two.
Link: https://lore.kernel.org/r/20220421183023.3462291-3-bvanassche@acm.org
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add several kernel-doc headers. Declare input arrays const. Specify the
array size in function declarations.
Link: https://lore.kernel.org/r/20220421183023.3462291-2-bvanassche@acm.org
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are no more end-users of REQ_OP_WRITE_SAME left, so we can start
deleting it.
Link: https://lore.kernel.org/r/20220209082828.2629273-5-hch@lst.de
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, pm80xx, lpfc,
mpi3mr, mpt3sas, hisi_sas, libsas) and minor updates and bug fixes.
The most impactful change is likely the switch from GFP_DMA to
GFP_KERNEL in a bunch of drivers, but even that shouldn't affect too
many people"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (121 commits)
scsi: mpi3mr: Bump driver version to 8.0.0.61.0
scsi: mpi3mr: Fixes around reply request queues
scsi: mpi3mr: Enhanced Task Management Support Reply handling
scsi: mpi3mr: Use TM response codes from MPI3 headers
scsi: mpi3mr: Add io_uring interface support in I/O-polled mode
scsi: mpi3mr: Print cable mngnt and temp threshold events
scsi: mpi3mr: Support Prepare for Reset event
scsi: mpi3mr: Add Event acknowledgment logic
scsi: mpi3mr: Gracefully handle online FW update operation
scsi: mpi3mr: Detect async reset that occurred in firmware
scsi: mpi3mr: Add IOC reinit function
scsi: mpi3mr: Handle offline FW activation in graceful manner
scsi: mpi3mr: Code refactor of IOC init - part2
scsi: mpi3mr: Code refactor of IOC init - part1
scsi: mpi3mr: Fault IOC when internal command gets timeout
scsi: mpi3mr: Display IOC firmware package version
scsi: mpi3mr: Handle unaligned PLL in unmap cmnds
scsi: mpi3mr: Increase internal cmnds timeout to 60s
scsi: mpi3mr: Do access status validation before adding devices
scsi: mpi3mr: Add support for PCIe Managed Switch SES device
...
|
|
Make sd_zbc_parse_report() use if/else when setting the write pointer,
instead of setting it unconditionally and then conditionally updating it.
Link: https://lore.kernel.org/r/20211201142821.64650-2-Niklas.Cassel@wdc.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
According to the ZBC (and ZAC) specification, a zone that has Zone Type set
to Conventional, must also have its Zone Condition set to "Not Write
Pointer".
Therefore, a conventional zone will never have Zone Condition set to
"Full", which means that we can omit the non-conventional prerequisite from
the zone full condition check.
Link: https://lore.kernel.org/r/20211201142821.64650-1-Niklas.Cassel@wdc.com
Suggested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Just use the disk attached to the request_queue instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch addresses the following Coverity report about the zno *
sdkp->zone_blocks expression:
CID 1475514 (#1 of 1): Unintentional integer overflow (OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression zno *
sdkp->zone_blocks with type unsigned int (32 bits, unsigned) is evaluated
using 32-bit arithmetic, and then used in a context that expects an
expression of type sector_t (64 bits, unsigned).
Link: https://lore.kernel.org/r/20210917212314.2362324-1-bvanassche@acm.org
Fixes: 5795eb443060 ("scsi: sd_zbc: emulate ZONE_APPEND commands")
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reporting zones on a SCSI device sometimes fail with the following error:
[76248.516390] ata16.00: invalid transfer count 131328
[76248.523618] sd 15:0:0:0: [sda] REPORT ZONES start lba 536870912 failed
The error (from drivers/ata/libata-scsi.c:ata_scsi_zbc_in_xlat()) indicates
that buffer size is not aligned to SECTOR_SIZE.
This happens when the __vmalloc() failed. Consider we are reporting 4096
zones, then we will have "bufsize = roundup((4096 + 1) * 64,
SECTOR_SIZE)" = (513 * 512) = 262656. Then, __vmalloc() failure halves
the bufsize to 131328, which is no longer aligned to SECTOR_SIZE.
Use rounddown() to ensure the size is always aligned to SECTOR_SIZE and fix
the comment as well.
Link: https://lore.kernel.org/r/20210906140642.2267569-1-naohiro.aota@wdc.com
Fixes: 23a50861adda ("scsi: sd_zbc: Cleanup sd_zbc_alloc_report_buffer()")
Cc: stable@vger.kernel.org # 5.5+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-4-bvanassche@acm.org
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace the check for DRIVER_SENSE with a check for
scsi_status_is_check_condition().
Audit all callsites to ensure the SAM status is set correctly. For
backwards compability move the DRIVER_SENSE definition to sg.h, and update
sg, bsg, and scsi_ioctl to set the DRIVER_SENSE driver_status whenever
SAM_STAT_CHECK_CONDITION is present.
[mkp: fix zeroday srp warning]
Link: https://lore.kernel.org/r/20210427083046.31620-10-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix
|
|
Return the actual error code in __scsi_execute() (which, according to the
documentation, should have happened anyway). And audit all callers to cope
with negative return values from __scsi_execute() and friends.
[mkp: resolve conflict and return bool]
Link: https://lore.kernel.org/r/20210427083046.31620-7-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/scsi/sd_zbc.c:137: warning: wrong kernel-doc identifier on line:
Link: https://lore.kernel.org/r/20210317091230.2912389-5-lee.jones@linaro.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Le Moal <damien.lemoal@hgst.com>
Cc: Shaun Tancheff <shaun.tancheff@seagate.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Recent changes changed the completion of SCSI commands from Soft-IRQ
context to IRQ context. This triggers the following warning, when we're
completing writes to zoned block devices that go through the zone append
emulation:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc2+ #2
Hardware name: Supermicro Super Server/X10SRL-F, BIOS 2.0 12/17/2015
RIP: 0010:__local_bh_disable_ip+0x3f/0x50
RSP: 0018:ffff8883e1409ba8 EFLAGS: 00010006
RAX: 0000000080010001 RBX: 0000000000000001 RCX: 0000000000000013
RDX: ffff888129e4d200 RSI: 0000000000000201 RDI: ffffffff915b9dbd
RBP: ffff888113e9a540 R08: ffff888113e9a540 R09: 00000000000077f0
R10: 0000000000080000 R11: 0000000000000001 R12: ffff888129e4d200
R13: 0000000000001000 R14: 00000000000077f0 R15: ffff888129e4d218
FS: 0000000000000000(0000) GS:ffff8883e1400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2f8418ebc0 CR3: 000000021202a006 CR4: 00000000001706f0
Call Trace:
<IRQ>
_raw_spin_lock_bh+0x18/0x40
sd_zbc_complete+0x43d/0x1150
sd_done+0x631/0x1040
? mark_lock+0xe4/0x2fd0
? provisioning_mode_store+0x3f0/0x3f0
scsi_finish_command+0x31b/0x5c0
_scsih_io_done+0x960/0x29e0 [mpt3sas]
? mpt3sas_scsih_scsi_lookup_get+0x1c7/0x340 [mpt3sas]
? __lock_acquire+0x166b/0x58b0
? _get_st_from_smid+0x4a/0x80 [mpt3sas]
_base_process_reply_queue+0x23f/0x26e0 [mpt3sas]
? lock_is_held_type+0x98/0x110
? find_held_lock+0x2c/0x110
? mpt3sas_base_sync_reply_irqs+0x360/0x360 [mpt3sas]
_base_interrupt+0x8d/0xd0 [mpt3sas]
? rcu_read_lock_sched_held+0x3f/0x70
__handle_irq_event_percpu+0x24d/0x600
handle_irq_event+0xef/0x240
? handle_irq_event_percpu+0x110/0x110
handle_edge_irq+0x1f6/0xb60
__common_interrupt+0x75/0x160
common_interrupt+0x7b/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
Don't use spin_lock_bh() to protect the update of the write pointer offset
cache, but use spin_lock_irqsave() for it.
Link: https://lore.kernel.org/r/3cfebe48d09db73041b7849be71ffbcec7ee40b3.1615369586.git.johannes.thumshirn@wdc.com
Fixes: 664f0dce2058 ("scsi: mpt3sas: Add support for shared host tagset for CPU hotplug")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more SCSI updates from James Bottomley:
"This is a few driver updates (iscsi, mpt3sas) that were still in the
staging queue when the merge window opened (all committed on or before
8 Feb) and some small bug fixes which came in during the merge window
(all committed on 22 Feb)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: hpsa: Correct dev cmds outstanding for retried cmds
scsi: sd: Fix Opal support
scsi: target: tcmu: Fix memory leak caused by wrong uio usage
scsi: target: tcmu: Move some functions without code change
scsi: sd: sd_zbc: Don't pass GFP_NOIO to kvcalloc
scsi: aic7xxx: Remove unused function pointer typedef ahc_bus_suspend/resume_t
scsi: bnx2fc: Fix Kconfig warning & CNIC build errors
scsi: ufs: Fix a duplicate dev quirk number
scsi: aic79xx: Fix spelling of version
scsi: target: core: Prevent underflow for service actions
scsi: target: core: Add cmd length set before cmd complete
scsi: iscsi: Drop session lock in iscsi_session_chkready()
scsi: qla4xxx: Use iscsi_is_session_online()
scsi: libiscsi: Reset max/exp cmdsn during recovery
scsi: iscsi_tcp: Fix shost can_queue initialization
scsi: libiscsi: Add helper to calculate max SCSI cmds per session
scsi: libiscsi: Fix iSCSI host workq destruction
scsi: libiscsi: Fix iscsi_task use after free()
scsi: libiscsi: Drop taskqueuelock
scsi: libiscsi: Fix iscsi_prep_scsi_cmd_pdu() error handling
...
|
|
Dan reported we're passing in GFP_NOIO to kvmalloc() which will then
fallback to doing kmalloc() instead of an optional vmalloc() if the size
exceeds kmalloc()s limits. This will break with drives that have zone
numbers exceeding PAGE_SIZE/sizeof(u32).
Instead of passing in GFP_NOIO, enter an implicit GFP_NOIO allocation
scope.
Link: https://lore.kernel.org/r/YCuvSfKw4qEQBr/t@mwanda
Link: https://lore.kernel.org/r/5a6345e2989fd06c049ac4e4627f6acb492c15b8.1613569821.git.johannes.thumshirn@wdc.com
Fixes: 5795eb443060: ("scsi: sd_zbc: emulate ZONE_APPEND commands")
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For host-aware ZBC disk, setting the device zoned model to BLK_ZONED_HA
using blk_queue_set_zoned() in sd_read_block_characteristics() may
result in the block device effective zoned model to be "none"
(BLK_ZONED_NONE) if partitions are present on the device. In this case,
sd_zbc_read_zones() should not setup the zone related queue limits for
the disk so that the device limits and configuration is consistent with
a regular disk and resources not uselessly allocated (e.g. the zone
write pointer tracking array for zone append emulation).
Furthermore, if the disk zoned model changes at run time due to the
creation of a partition by the user, the zone related resources can be
released.
Fix both problems by introducing the function sd_zbc_clear_zone_info()
to reset the scsi disk zone information and free resources and by
returning early in sd_zbc_read_zones() for a block device that has a
zoned model equal to BLK_ZONED_NONE.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@edc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Per ZBC and ZAC specifications, host-managed SMR hard-disks mandate that
all writes into sequential write required zones be aligned to the device
physical block size. However, NVMe ZNS does not have this constraint and
allows write operations into sequential zones to be aligned to the
device logical block size. This inconsistency does not help with
software portability across device types.
To solve this, introduce the zone_write_granularity queue limit to
indicate the alignment constraint, in bytes, of write operations into
zones of a zoned block device. This new limit is exported as a
read-only sysfs queue attribute and the helper
blk_queue_zone_write_granularity() introduced for drivers to set this
limit.
The function blk_queue_set_zoned() is modified to set this new limit to
the device logical block size by default. NVMe ZNS devices as well as
zoned nullb devices use this default value as is. The scsi disk driver
is modified to execute the blk_queue_zone_write_granularity() helper to
set the zone write granularity of host-managed SMR disks to the disk
physical block size.
The accessor functions queue_zone_write_granularity() and
bdev_zone_write_granularity() are also introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@edc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Make sure to call sd_zbc_init_disk() when the sdkp->zoned field is known,
that is, once sd_read_block_characteristics() is executed in
sd_revalidate_disk(), so that host-aware disks also get initialized. To do
so, move sd_zbc_init_disk() call in sd_zbc_revalidate_zones() and make sure
to execute it for all zoned disks, including for host-aware disks used as
regular disks as these disk zoned model may be changed back to BLK_ZONED_HA
when partitions are deleted.
Link: https://lore.kernel.org/r/20200915073347.832424-3-damien.lemoal@wdc.com
Fixes: 5795eb443060 ("scsi: sd_zbc: emulate ZONE_APPEND commands")
Cc: <stable@vger.kernel.org> # v5.8+
Reported-by: Borislav Petkov <bp@alien8.de>
Tested-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When CONFIG_BLK_DEV_ZONED is disabled, allow using host-aware ZBC disks as
regular disks. In this case, ensure that command completion is correctly
executed by changing sd_zbc_complete() to return good_bytes instead of 0
and causing a hang during device probe (endless retries).
When CONFIG_BLK_DEV_ZONED is enabled and a host-aware disk is detected to
have partitions, it will be used as a regular disk. In this case, make sure
to not do anything in sd_zbc_revalidate_zones() as that triggers warnings.
Since all these different cases result in subtle settings of the disk queue
zoned model, introduce the block layer helper function
blk_queue_set_zoned() to generically implement setting up the effective
zoned model according to the disk type, the presence of partitions on the
disk and CONFIG_BLK_DEV_ZONED configuration.
Link: https://lore.kernel.org/r/20200915073347.832424-2-damien.lemoal@wdc.com
Fixes: b72053072c0b ("block: allow partitions on host aware zone devices")
Cc: <stable@vger.kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more SCSI updates from James Bottomley:
"This is the set of patches which arrived too late to stabilise in
-next for the first pull.
It's really just an lpfc driver update and an assortment of minor
fixes, all in drivers. The only core update is to the zone block
device driver, which isn't the one most people use"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Update lpfc version to 12.8.0.3
scsi: lpfc: Fix LUN loss after cable pull
scsi: lpfc: Fix validation of bsg reply lengths
scsi: lpfc: Fix retry of PRLI when status indicates its unsupported
scsi: lpfc: Fix oops when unloading driver while running mds diags
scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter
scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value
scsi: lpfc: Fix FCoE speed reporting
scsi: lpfc: Add missing misc_deregister() for lpfc_init()
scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport
scsi: scsi_transport_sas: Add spaces around binary operator "|"
scsi: sd_zbc: Improve zone revalidation
scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases
scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del()
scsi: target: Make iscsit_register_transport() return void
|
|
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
|
|
Currently, for zoned disks, since blk_revalidate_disk_zones() requires the
disk capacity to be set already to operate correctly, zones revalidation
can only be done on the second revalidate scan once the gendisk capacity is
set at the end of the first scan. As a result, if zone revalidation fails,
there is no second chance to recover from the failure and the disk capacity
is changed to 0, with the disk left unusable.
This can be improved by shuffling around code, specifically, by moving the
call to sd_zbc_revalidate_zones() from sd_zbc_read_zones() to the end of
sd_revalidate_disk(), after set_capacity_revalidate_and_notify() is called
to set the gendisk capacity. With this change, if sd_zbc_revalidate_zones()
fails on the first scan, the second scan will call it again to recover, if
possible.
Using the new struct scsi_disk fields rev_nr_zones and rev_zone_blocks,
sd_zbc_revalidate_zones() does actual work only if it detects a change with
the disk zone configuration. This means that for a successful zones
revalidation on the first scan, the second scan will not cause another
heavy full check.
While at it, remove the unecesary "extern" declaration of
sd_zbc_read_zones().
Link: https://lore.kernel.org/r/20200731054928.668547-1-damien.lemoal@wdc.com
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Don't clamp the maximum number of zone append sectors to the maximum number
of hardware sectors in sd as the block layer is already enforcing this
limit when setting max_zone_append_sectors.
Link: https://lore.kernel.org/r/20200716091606.38316-1-johannes.thumshirn@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a new max_active zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max_active_zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_active_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
For SCSI devices, even though max active zones is not part of the ZBC/ZAC
spec, export max_active_zones as 0, signifying "no limit".
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add a new max_open_zones definition in the sysfs documentation.
This definition will be common for all devices utilizing the zoned block
device support in the kernel.
Export max open zones according to this new definition for NVMe Zoned
Namespace devices, ZAC ATA devices (which are treated as SCSI devices by
the kernel), and ZBC SCSI devices.
Add the new max_open_zones member to struct request_queue, rather
than as a queue limit, since this property cannot be split across stacking
drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In the zoned storage model, the sectors within a zone are typically all
writeable. With the introduction of the Zoned Namespace (ZNS) Command
Set in the NVM Express organization, the model was extended to have a
specific writeable capacity.
Extend the zone descriptor data structure with a zone capacity field to
indicate to the user how many sectors in a zone are writeable.
Introduce backward compatibility in the zone report ioctl by extending
the zone report header data structure with a flags field to indicate if
the capacity field is available.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Javier González <javier.gonz@samsung.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Fix the kdoc comment of the function sd_zbc_check_capacity() to avoid a
compiler warning when compiling with W=1.
No functional changes.
Link: https://lore.kernel.org/r/20200706123355.452091-1-damien.lemoal@wdc.com
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull block updates from Jens Axboe:
"Core block changes that have been queued up for this release:
- Remove dead blk-throttle and blk-wbt code (Guoqing)
- Include pid in blktrace note traces (Jan)
- Don't spew I/O errors on wouldblock termination (me)
- Zone append addition (Johannes, Keith, Damien)
- IO accounting improvements (Konstantin, Christoph)
- blk-mq hardware map update improvements (Ming)
- Scheduler dispatch improvement (Salman)
- Inline block encryption support (Satya)
- Request map fixes and improvements (Weiping)
- blk-iocost tweaks (Tejun)
- Fix for timeout failing with error injection (Keith)
- Queue re-run fixes (Douglas)
- CPU hotplug improvements (Christoph)
- Queue entry/exit improvements (Christoph)
- Move DMA drain handling to the few drivers that use it (Christoph)
- Partition handling cleanups (Christoph)"
* tag 'for-5.8/block-2020-06-01' of git://git.kernel.dk/linux-block: (127 commits)
block: mark bio_wouldblock_error() bio with BIO_QUIET
blk-wbt: rename __wbt_update_limits to wbt_update_limits
blk-wbt: remove wbt_update_limits
blk-throttle: remove tg_drain_bios
blk-throttle: remove blk_throtl_drain
null_blk: force complete for timeout request
blk-mq: drain I/O when all CPUs in a hctx are offline
blk-mq: add blk_mq_all_tag_iter
blk-mq: open code __blk_mq_alloc_request in blk_mq_alloc_request_hctx
blk-mq: use BLK_MQ_NO_TAG in more places
blk-mq: rename BLK_MQ_TAG_FAIL to BLK_MQ_NO_TAG
blk-mq: move more request initialization to blk_mq_rq_ctx_init
blk-mq: simplify the blk_mq_get_request calling convention
blk-mq: remove the bio argument to ->prepare_request
nvme: force complete cancelled requests
blk-mq: blk-mq: provide forced completion method
block: fix a warning when blkdev.h is included for !CONFIG_BLOCK builds
block: blk-crypto-fallback: remove redundant initialization of variable err
block: reduce part_stat_lock() scope
block: use __this_cpu_add() instead of access by smp_processor_id()
...
|
|
The pgprot argument to __vmalloc is always PAGE_KERNEL now, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com> [hyperv]
Acked-by: Gao Xiang <xiang@kernel.org> [erofs]
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200414131348.444715-22-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Emulate ZONE_APPEND for SCSI disks using a regular WRITE(16) command
with a start LBA set to the target zone write pointer position.
In order to always know the write pointer position of a sequential write
zone, the write pointer of all zones is tracked using an array of 32bits
zone write pointer offset attached to the scsi disk structure. Each
entry of the array indicate a zone write pointer position relative to
the zone start sector. The write pointer offsets are maintained in sync
with the device as follows:
1) the write pointer offset of a zone is reset to 0 when a
REQ_OP_ZONE_RESET command completes.
2) the write pointer offset of a zone is set to the zone size when a
REQ_OP_ZONE_FINISH command completes.
3) the write pointer offset of a zone is incremented by the number of
512B sectors written when a write, write same or a zone append
command completes.
4) the write pointer offset of all zones is reset to 0 when a
REQ_OP_ZONE_RESET_ALL command completes.
Since the block layer does not write lock zones for zone append
commands, to ensure a sequential ordering of the regular write commands
used for the emulation, the target zone of a zone append command is
locked when the function sd_zbc_prepare_zone_append() is called from
sd_setup_read_write_cmnd(). If the zone write lock cannot be obtained
(e.g. a zone append is in-flight or a regular write has already locked
the zone), the zone append command dispatching is delayed by returning
BLK_STS_ZONE_RESOURCE.
To avoid the need for write locking all zones for REQ_OP_ZONE_RESET_ALL
requests, use a spinlock to protect accesses and modifications of the
zone write pointer offsets. This spinlock is initialized from sd_probe()
using the new function sd_zbc_init().
Co-developed-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
