summaryrefslogtreecommitdiff
path: root/drivers/thunderbolt
AgeCommit message (Collapse)Author
2024-05-31thunderbolt: debugfs: Fix margin debugfs node creation conditionAapo Vienamo
The margin debugfs node controls the "Enable Margin Test" field of the lane margining operations. This field selects between either low or high voltage margin values for voltage margin test or left or right timing margin values for timing margin test. According to the USB4 specification, whether or not the "Enable Margin Test" control applies, depends on the values of the "Independent High/Low Voltage Margin" or "Independent Left/Right Timing Margin" capability fields for voltage and timing margin tests respectively. The pre-existing condition enabled the debugfs node also in the case where both low/high or left/right margins are returned, which is incorrect. This change only enables the debugfs node in question, if the specific required capability values are met. Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com> Fixes: d0f1e0c2a699 ("thunderbolt: Add support for receiver lane margining") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-05-10Merge tag 'thunderbolt-for-v6.10-rc1' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next Mika writes: thunderbolt: Changes for v6.10 merge window This includes following USB4/Thunderbolt changes for the v6.10 merge window: - Enable NVM firmare upgrade on Intel Maple Ridge Thunderbolt 4 controller - Improve USB3 tunnel bandwidth calculation - Improve sideband access - Minor cleanups and fixes. All these have been in linux-next with no reported issues. * tag 'thunderbolt-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: thunderbolt: Correct trace output of firmware connection manager packets thunderbolt: Fix kernel-doc for tb_tunnel_alloc_dp() thunderbolt: Fix uninitialized variable in tb_tunnel_alloc_usb3() thunderbolt: There are only 5 basic router registers in pre-USB4 routers thunderbolt: No need to loop over all retimers if access fails thunderbolt: Increase sideband access polling delay thunderbolt: Get rid of TB_CFG_PKG_PREPARE_TO_SLEEP thunderbolt: Use correct error code with ERROR_NOT_SUPPORTED thunderbolt: Allow USB3 bandwidth to be lower than maximum supported thunderbolt: Fix calculation of consumed USB3 bandwidth on a path thunderbolt: Enable NVM upgrade support on Intel Maple Ridge
2024-04-29thunderbolt: Correct trace output of firmware connection manager packetsMika Westerberg
These are special packets that the drivers sends directly to the firmware connection manager (ICM). These do not have route string because they are always consumed by the firmware connection manager running on the host router, so hard-code that in the output accordingly. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-27thunderbolt: Fix kernel-doc for tb_tunnel_alloc_dp()Gil Fine
In case of no bandwidth available for DP tunnel, the function get the arguments @max_up and @max_down set to zero. Fix the kernel-doc to describe more accurately the purpose of the function. No functional changes. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-27thunderbolt: Fix uninitialized variable in tb_tunnel_alloc_usb3()Gil Fine
Currently in case of no bandwidth available for USB3 tunnel, we are left with uninitialized variable that can lead to huge negative allocated bandwidth. Fix this by initializing the variable to zero. While there, fix the kernel-doc to describe more accurately the purpose of the function tb_tunnel_alloc_usb3(). Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/linux-usb/6289898b-cd63-4fb8-906a-1b6977321af9@moroto.mountain/ Fixes: 25d905d2b819 ("thunderbolt: Allow USB3 bandwidth to be lower than maximum supported") Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-24thunderbolt: There are only 5 basic router registers in pre-USB4 routersMika Westerberg
Intel pre-USB4 routers only have ROUTER_CS_0 up to ROUTER_CS_4 and it immediately follows the TMU router registers. Correct this accordingly. Reported-by: Rajaram Regupathy <rajaram.regupathy@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-23thunderbolt: No need to loop over all retimers if access failsMika Westerberg
When we read the NVM authentication status or unsetting the inbound SBTX there is no point to continue the loop after first access to a retimer fails because there won't be any more retimers after this anyway so bail out from the loops early. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-23thunderbolt: Increase sideband access polling delayMika Westerberg
The USB4 sideband access is slow compared to the high-speed link and the access timing parameters are tens of milliseconds according the spec. To avoid too much unnecessary polling for the sideband pass the wait delay to usb4_port_wait_for_bit() and use larger (5ms) value compared to the high-speed access. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-19thunderbolt: Get rid of TB_CFG_PKG_PREPARE_TO_SLEEPMika Westerberg
This is not used anywhere in the driver so remove it. No functional changes. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-19thunderbolt: Use correct error code with ERROR_NOT_SUPPORTEDMika Westerberg
We check for -EOPNOTSUPP but tb_xdp_handle_error() translated it to -ENOTSUPP instead which is dealt as "transient" error and retried after a while. Fix this so that we bail out early when the other side clearly tells us it is does not support this. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-12thunderbolt: Allow USB3 bandwidth to be lower than maximum supportedGil Fine
Currently USB3 tunnel setup fails if USB4 link available bandwidth is too low to allow USB3 Maximum Supported Link Rate. In reality, this limitation is not needed, and may cause failure of USB3 tunnel establishment, if USB4 link available bandwidth is lower than USB3 Maximum Supported Link Rate. E.g. if we connect to USB4 v1 host router, a USB4 v1 device router, via 10 Gb/s cable. Hence, here we discard this limitation, and now we only limit USB3 bandwidth allocation to be not higher than 90% of USB3 Max Supported Link Rate (for first USB3 tunnel only). Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-12thunderbolt: Fix calculation of consumed USB3 bandwidth on a pathGil Fine
Currently, when setup a new USB3 tunnel that is starting from downstream USB3 adapter of first depth router (or deeper), to upstream USB3 adapter of a second depth router (or deeper), we calculate consumed bandwidth. For this calculation we take into account first USB3 tunnel consumed bandwidth while we shouldn't, because we just recalculating the first USB3 tunnel allocated bandwidth. Fix that, so that more bandwidth is available for the new USB3 tunnel being setup. While there, fix the kernel-doc to decribe more accurately the purpose of the function. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-10thunderbolt: Avoid notify PM core about runtime PM resumeGil Fine
Currently we notify PM core about occurred wakes after any resume. This is not actually needed after resume from runtime suspend. Hence, notify PM core about occurred wakes only after resume from system sleep. Also, if the wake occurred in USB4 router upstream port, we don't notify the PM core about it since it is not actually needed and can cause unexpected autowake (e.g. if /sys/power/wakeup_count is used). While there add the missing kernel-doc for tb_switch_resume(). Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-10thunderbolt: Fix wake configurations after device unplugGil Fine
Currently we don't configure correctly the wake events after unplug of device router. What can happen is that the downstream ports of host router will be configured to wake on: USB4-wake and wake-on-disconnect, but not on wake-on-connect. This may cause the later plugged device not to wake the domain and fail in enumeration. Fix this by clearing downstream port's "USB4 Port is Configured" bit, after unplug of a device router. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-08thunderbolt: Enable NVM upgrade support on Intel Maple RidgeAlex James
Intel Maple Ridge supports NVM firmware upgrade with the same flows used on previous discrete Thunderbolt contollers from Intel (such as Titan Ridge). Advertise NVM upgrade support for Maple Ridge in icm_probe() to expose the corresponding files in /sys/bus/thunderbolt. The NVM firmware process was successfully tested on a system with a JHL8540 controller (ASUS ProArt Z790-CREATOR). Signed-off-by: Alex James <git@alextjam.es> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-04-02thunderbolt: Do not create DisplayPort tunnels on adapters of the same routerMika Westerberg
Probably due to a firmware bug Dell TB16 dock announces that one of its DisplayPort adapters is actually DP IN. Now this is possible and used with some external GPUs but not likely in this case as we are dealing with a dock. Anyways the problem is that the driver tries to create a DisplayPort tunnel between adapters of the same router which then shows to user that there is no picture on the display (because there are no available DP OUT adapters on the dock anymore). Fix this by not creating DisplayPort tunnels between adapters that are on the same router. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10265 Fixes: 274baf695b08 ("thunderbolt: Add DP IN added last in the head of the list of DP resources") Cc: Gil Fine <gil.fine@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-03-21Merge tag 'usb-6.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of USB and Thunderbolt changes for 6.9-rc1. Lots of tiny changes and forward progress to support new hardware and better support for existing devices. Included in here are: - Thunderbolt (i.e. USB4) updates for newer hardware and uses as more people start to use the hardware - default USB authentication mode Kconfig and documentation update to make it more obvious what is going on - USB typec updates and enhancements - usual dwc3 driver updates - usual xhci driver updates - function USB (i.e. gadget) driver updates and additions - new device ids for lots of drivers - loads of other small updates, full details in the shortlog All of these, including a "last minute regression fix" have been in linux-next with no reported issues" * tag 'usb-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (185 commits) usb: usb-acpi: Fix oops due to freeing uninitialized pld pointer usb: gadget: net2272: Use irqflags in the call to net2272_probe_fin usb: gadget: tegra-xudc: Fix USB3 PHY retrieval logic phy: tegra: xusb: Add API to retrieve the port number of phy USB: gadget: pxa27x_udc: Remove unused of_gpio.h usb: gadget/snps_udc_plat: Remove unused of_gpio.h usb: ohci-pxa27x: Remove unused of_gpio.h usb: sl811-hcd: only defined function checkdone if QUIRK2 is defined usb: Clarify expected behavior of dev_bin_attrs_are_visible() xhci: Allow RPM on the USB controller (1022:43f7) by default usb: isp1760: remove SLAB_MEM_SPREAD flag usage usb: misc: onboard_hub: use pointer consistently in the probe function usb: gadget: fsl: Increase size of name buffer for endpoints usb: gadget: fsl: Add of device table to enable module autoloading usb: typec: tcpm: add support to set tcpc connector orientatition usb: typec: tcpci: add generic tcpci fallback compatible dt-bindings: usb: typec-tcpci: add tcpci fallback binding usb: gadget: fsl-udc: Replace custom log wrappers by dev_{err,warn,dbg,vdbg} usb: core: Set connect_type of ports based on DT node dt-bindings: usb: Add downstream facing ports to realtek binding ...
2024-03-02Merge tag 'thunderbolt-for-v6.9-rc1' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next Mika writes: thunderbolt: Changes for v6.9 merge window This includes following USB4/Thunderbolt changes for the v6.9 merge window: - Reset the topology also for USB4 v1 routers on driver load - DisplayPort tunneling and bandwidth allocation mode improvements - Tracepoint support for the control channel - Couple of minor fixes and cleanups. All these have been in linux-next with no reported issues. * tag 'thunderbolt-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: (23 commits) thunderbolt: Constify the struct device_type usage thunderbolt: Add trace events support for the control channel thunderbolt: Keep the domain powered when USB4 port is in redrive mode thunderbolt: Improve DisplayPort tunnel setup process to be more robust thunderbolt: Calculate DisplayPort tunnel bandwidth after DPRX capabilities read thunderbolt: Reserve released DisplayPort bandwidth for a group for 10 seconds thunderbolt: Introduce tb_tunnel_direction_downstream() thunderbolt: Re-order bandwidth group functions thunderbolt: Fail the failed bandwidth request properly thunderbolt: Log an error if DPTX request is not cleared thunderbolt: Handle bandwidth allocation mode disable request thunderbolt: Re-calculate estimated bandwidth when allocation mode is enabled thunderbolt: Use DP_LOCAL_CAP for maximum bandwidth calculation thunderbolt: Correct typo in host_reset parameter thunderbolt: Skip discovery also in USB4 v2 host thunderbolt: Reset only non-USB4 host routers in resume thunderbolt: Remove usage of the deprecated ida_simple_xx() API thunderbolt: Fix rollback in tb_port_lane_bonding_enable() for lane 1 thunderbolt: Fix XDomain rx_lanes_show and tx_lanes_show thunderbolt: Reset topology created by the boot firmware ...
2024-03-02Merge tag 'thunderbolt-for-v6.8-rc7' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus Mika writes: thunderbolt: Fix for v6.8-rc7 This includes one USB4/Thunderbolt fix for v6.8-rc7: - Fix NULL pointer dereference in tb_port_update_credits() on Apple Thunderbolt 1 hardware. This has been in linux-next with no reported issues. * tag 'thunderbolt-for-v6.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: thunderbolt: Fix NULL pointer dereference in tb_port_update_credits()
2024-02-26thunderbolt: Constify the struct device_type usageRicardo B. Marliere
Since commit aed65af1cc2f ("drivers: make device_type const"), the driver core can properly handle constant struct device_type. Move the tb_domain_type, tb_retimer_type, tb_switch_type, usb4_port_device_type, tb_service_type and tb_xdomain_type variables to be constant structures as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-26thunderbolt: Add trace events support for the control channelGil Fine
Sometimes it is useful to see the traffic happening inside the control channel, especially when debugging a possible problem. This adds tracepoints close to the hardware which can be enabled dynamically as needed using the standard Linux trace events facility. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-26thunderbolt: Keep the domain powered when USB4 port is in redrive modeMika Westerberg
If a DiplayPort cable is directly connected to the host routers USB4 port, there is no tunnel involved but the port is in "redrive" mode meaning that it is re-driving the DisplayPort signals from its DisplayPort source. In this case we need to keep the domain powered on otherwise once the domain enters D3cold the connected monitor blanks too. Since this happens only on Intel Barlow Ridge add a quirk that takes runtime PM reference if we detect that the USB4 port entered redrive mode (and release it once it exits the mode). Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Improve DisplayPort tunnel setup process to be more robustGil Fine
After DisplayPort tunnel setup, we add verification that the DPRX capabilities read process completed. Otherwise, we bail out, teardown the tunnel, and try setup another DisplayPort tunnel using next available DP IN adapter. We do so till all DP IN adapters tried. This way, we avoid allocating DP IN adapter and (bandwidth for it) for unusable tunnel. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Calculate DisplayPort tunnel bandwidth after DPRX capabilities readGil Fine
According to USB4 Connection Manager guide, after DisplayPort tunnel was setup, the DPRX capabilities read is performed by the DPTX. According to VESA spec, this shall be completed within 5 seconds after the DisplayPort tunnel was setup. Hence, if the bit: DPRX Capabilities Read Done, was not set to '1' by this time, we timeout and fail calculating DisplayPort tunnel consumed bandwidth. Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Reserve released DisplayPort bandwidth for a group for 10 secondsMika Westerberg
The USB4 spec says that the Connection Manager should reserve the bandwidth that is released in the same group for 10 seconds before it can be shared with other groups. Add support for this. We also delay the symmetric transition by that same 10 seconds to avoid any unnecessary transitions (i.e if the released bandwidth is used by another DisplayPort tunnel in the same group the link can stay asymmetric the whole time). Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Introduce tb_tunnel_direction_downstream()Mika Westerberg
This helper takes tunnel as parameter. Convert existing code to call this where possible. No functional changes. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Re-order bandwidth group functionsMika Westerberg
This is needed by the following patches so that we do not have to add forward declaratations for any of these. Separating the move and the actual changes also makes it easier to review the code. No functional changes. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Fail the failed bandwidth request properlyMika Westerberg
The USB4 spec says that if the Connection Manager writes Allocated_BW that is smaller than Requested_BW, the DisplayPort IN adapter signals this failure back to the DPTX (graphics driver). Implement this by rewriting the same allocated bandwidth values back. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Log an error if DPTX request is not clearedMika Westerberg
This helps debugging issues around DisplayPort bandwidth allocation mode. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Handle bandwidth allocation mode disable requestMika Westerberg
Graphics can disable DisplayPort bandwidth allocation mode as well so if this make sure to reset the tunnel state accordingly. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Re-calculate estimated bandwidth when allocation mode is enabledMika Westerberg
When we program the initial bandwidth estimation the DPTX (graphics driver) has not yet read the capabilities of the monitor so the values used are the highest possible of the involved DisplayPort IN and OUT adapters, not the actual monitor capabilities. To allow the graphics more accurate bandwidth estimation re-calculate it once we receive the bandwidth allocation mode enabled notification. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Use DP_LOCAL_CAP for maximum bandwidth calculationMika Westerberg
The DisplayPort IN adapter DP_LOCAL_CAP holds the aggregated capabilities and gets updated after graphics side does the DPRX capabilities read so we should use this to figure out the maximum possible bandwidth for the DisplayPort tunnel. While there make the variable name to match better what it is used for and add kernel-doc comment to the function. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-16thunderbolt: Fix NULL pointer dereference in tb_port_update_credits()Mika Westerberg
Olliver reported that his system crashes when plugging in Thunderbolt 1 device: BUG: kernel NULL pointer dereference, address: 0000000000000020 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:tb_port_do_update_credits+0x1b/0x130 [thunderbolt] Call Trace: <TASK> ? __die+0x23/0x70 ? page_fault_oops+0x171/0x4e0 ? exc_page_fault+0x7f/0x180 ? asm_exc_page_fault+0x26/0x30 ? tb_port_do_update_credits+0x1b/0x130 ? tb_switch_update_link_attributes+0x83/0xd0 tb_switch_add+0x7a2/0xfe0 tb_scan_port+0x236/0x6f0 tb_handle_hotplug+0x6db/0x900 process_one_work+0x171/0x340 worker_thread+0x27b/0x3a0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe5/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> This is due the fact that some Thunderbolt 1 devices only have one lane adapter. Fix this by checking for the lane 1 before we read its credits. Reported-by: Olliver Schinagl <oliver@schinagl.nl> Closes: https://lore.kernel.org/linux-usb/c24c7882-6254-4e68-8f22-f3e8f65dc84f@schinagl.nl/ Fixes: 81af2952e606 ("thunderbolt: Add support for asymmetric link") Cc: stable@vger.kernel.org Cc: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-13thunderbolt: Correct typo in host_reset parameterMika Westerberg
It should say USB4 now since we reset by default all USB4 host routers. Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-13thunderbolt: Skip discovery also in USB4 v2 hostMika Westerberg
If the host router is reset, there is no point running discovery as the links are down. Furthermore this prevents CL-state enabling. For this reason skip discovery in USB4 v2 host the same way we do with USB4 v1. Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-02-13thunderbolt: Reset only non-USB4 host routers in resumeMika Westerberg
There is no need to reset the USB4 host routers on resume because they are reset already and this may cause problems if the link does not come up soon enough. For this reason limit this to happen in non-USB4 host routers only (that's Apple systems with Intel Thunderbolt controllers). Fixes: 59a54c5f3dbd ("thunderbolt: Reset topology created by the boot firmware") Cc: Sanath S <Sanath.S@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-29thunderbolt: Fix setting the CNS bit in ROUTER_CS_5Mohammad Rahimi
The bit 23, CM TBT3 Not Supported (CNS), in ROUTER_CS_5 indicates whether a USB4 Connection Manager is TBT3-Compatible and should be: 0b for TBT3-Compatible 1b for Not TBT3-Compatible Fixes: b04079837b20 ("thunderbolt: Add initial support for USB4") Cc: stable@vger.kernel.org Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-23thunderbolt: Remove usage of the deprecated ida_simple_xx() APIChristophe JAILLET
ida_alloc() and ida_free() should be preferred to the deprecated ida_simple_get() and ida_simple_remove(). Note that the upper limit of ida_simple_get() is exclusive, but the one of ida_alloc_range()/ida_alloc_max() is inclusive. So a -1 has been added when needed. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Fix rollback in tb_port_lane_bonding_enable() for lane 1Mohammad Rahimi
If enabling lane bonding on lane 1 of a USB4 port results in an error, the rollback should set TB_LINK_WIDTH_SINGLE for both lanes. Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Fix XDomain rx_lanes_show and tx_lanes_showMohammad Rahimi
If the Inter-Domain link is operating in asymmetric TB_LINK_WIDTH_ASYM_TX mode, the rx_lanes_show should return 1 since there is only one receiver and tx_lanes_show should return 3 since there are 3 transmitters. Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Reset topology created by the boot firmwareSanath S
Boot firmware (typically BIOS) might have created tunnels of its own. The tunnel configuration that it does might be sub-optimal. For instance it may only support HBR2 monitors so the DisplayPort tunnels it created may limit Linux graphics drivers. In addition there is an issue on some AMD based systems where the BIOS does not allocate enough PCIe resources for future topology extension. By resetting the USB4 topology the PCIe links will be reset as well allowing Linux to re-allocate. This aligns the behavior with Windows Connection Manager. We already issued host router reset for USB4 v2 routers, now extend it to USB4 v1 routers as well. For pre-USB4 (that's Apple systems) we leave it as is and continue to discover the existing tunnels. Suggested-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Make tb_switch_reset() support Thunderbolt 2, 3 and USB4 routersSanath S
Currently tb_switch_reset() only did something for Thunderbolt 1 devices. Expand this to support all generations, including USB4, and both host and device routers. Signed-off-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Introduce tb_path_deactivate_hop()Sanath S
This function can be used to clear path config space of an adapter. Make it available for other files in this driver. Signed-off-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-22thunderbolt: Introduce tb_port_reset()Sanath S
Introduce a function that issues Downstream Port Reset to a USB4 port. This supports Thunderbolt 2, 3 and USB4 routers. Signed-off-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2024-01-18Merge tag 'usb-6.8-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt updates from Greg KH: "Here is the big set of USB and Thunderbolt changes for 6.8-rc1. Included in here are the following: - Thunderbolt subsystem and driver updates for USB 4 hardware and issues reported by real devices - xhci driver updates - dwc3 driver updates - uvc_video gadget driver updates - typec driver updates - gadget string functions cleaned up - other small changes All of these have been in the linux-next tree for a while with no reported issues" * tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits) usb: typec: tipd: fix use of device-specific init function usb: typec: tipd: Separate reset for TPS6598x usb: mon: Fix atomicity violation in mon_bin_vma_fault usb: gadget: uvc: Remove nested locking usb: gadget: uvc: Fix use are free during STREAMOFF usb: typec: class: fix typec_altmode_put_partner to put plugs dt-bindings: usb: dwc3: Limit num-hc-interrupters definition dt-bindings: usb: xhci: Add num-hc-interrupters definition xhci: add support to allocate several interrupters USB: core: Use device_driver directly in struct usb_driver and usb_device_driver arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue arm64: dts: qcom: msm8996: Remove PNoC clock from MSS arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI arm64: dts: qcom: msm8939: Drop RPM bus clocks arm64: dts: qcom: sdm630: Drop RPM bus clocks arm64: dts: qcom: qcs404: Drop RPM bus clocks arm64: dts: qcom: msm8996: Drop RPM bus clocks ...
2024-01-02Merge tag 'thunderbolt-for-v6.8-rc1' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into char-misc-next Mika writes: thunderbolt: Changes for v6.8 merge window This includes following USB4/Thunderbolt changes for the v6.8 merge window: - Intel Lunar Lake support - PCIe tunneling improvements - DisplayPort tunneling improvements - Asymmetric switching improvements - Couple of minor fixes and cleanups. All these have been in linux-next with no reported issues. * tag 'thunderbolt-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: thunderbolt: Reduce retry timeout to speed up boot for some devices thunderbolt: Keep link as asymmetric if preferred by hardware thunderbolt: Add support for Intel Lunar Lake thunderbolt: Disable PCIe extended encapsulation upon teardown properly thunderbolt: Make PCIe tunnel setup and teardown follow CM guide thunderbolt: Improve logging when DisplayPort resource is added due to hotplug thunderbolt: Use tb_dp_read_cap() to read DP_COMMON_CAP as well thunderbolt: Disable CL states only when actually needed thunderbolt: Transition link to asymmetric only when both sides support it thunderbolt: Log XDomain link speed and width thunderbolt: Move width_name() helper to tb.h thunderbolt: Handle lane bonding of Gen 4 XDomain links properly thunderbolt: Unwind TMU configuration if tb_switch_set_tmu_mode_params() fails thunderbolt: Remove duplicated re-assignment of pointer 'out'
2023-12-22thunderbolt: Reduce retry timeout to speed up boot for some devicesWerner Sembach
This is a followup to "thunderbolt: Workaround an IOMMU fault on certain systems with Intel Maple Ridge". It seems like the timeout can be reduced to 250ms. This reduces the overall delay caused by the retires to ~1s. This is about the time other things being initialized in parallel need anyway*, so like this the effective boot time is no longer compromised. *I only had a single device available for my measurements: A Clevo X170KM-G desktop replacement notebook. Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2023-12-22thunderbolt: Keep link as asymmetric if preferred by hardwareGil Fine
In case of the link is brought up as asymmetric (due to hardware preference), we honor that and don't transition it to symmetric, unless a router with symmetric link got plugged below, in the topology (and a bandwidth allows transition to symmetric). Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2023-12-20thunderbolt: make tb_bus_type constGreg Kroah-Hartman
Now that the driver core can properly handle constant struct bus_type, move the tb_bus_type variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Andreas Noever <andreas.noever@gmail.com> Cc: Michael Jamet <michael.jamet@intel.com> Cc: Yehezkel Bernat <YehezkelShB@gmail.com> Cc: <linux-usb@vger.kernel.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/2023121904-utopia-broadcast-06d1@gregkh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-14thunderbolt: Add support for Intel Lunar LakeMika Westerberg
Intel Lunar Lake has similar integrated Thunderbolt/USB4 controller as Intel Meteor Lake with some small differences in the host router (it has 3 DP IN adapters for instance). Add the Intel Lunar Lake PCI IDs to the driver list of supported devices. Tested-by: Pengfei Xu <pengfei.xu@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>