Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (141 commits)
  MIPS: Alchemy: defconfig updates
  MIPS: Alchemy: Fix Au1100 ethernet build failure
  MIPS: Alchemy: Repair db1500/bosporus builds
  MIPS: ARC: Cleanup unused definitions from sgialib.h
  MIPS: Cobalt: convert legacy port addresses to GT-64111 bus addresses
  MIPS: Alchemy: use 36bit addresses for PCMCIA resources.
  MIPS: Cobalt: Fix theoretical port aliasing issue
  MIPS: Use ALIGN(x, bytes) instead of __ALIGN_MASK(x, bytes - 1)
  MIPS: Crazy spinlock speed test.
  MIPS: Optimize spinlocks.
  MIPS: Alchemy: devboard PM needs to save CPLD registers.
  MIPS: PowerTV: Eliminate duplicate opcode definition macros
  MIPS: Lemote 2F: Move printks out of port_access_lock.
  MIPS: PNX833x: Convert IRQ controller locks to raw spinlocks.
  MIPS: Octeon: Replace spinlock with raw_spinlocks in dma-octeon.c.
  MIPS: Octeon: Replace rwlocks in irq_chip handlers with raw_spinlocks.
  MIPS: Octeon: Convert octeon_irq_msi_lock to raw spinlock.
  MIPS: Loongson: Remove pointless sample_lock from oprofile code.
  MIPS: SNI: Convert sni_rm200_i8259A_lock to raw spinlock.
  MIPS: i8259: Convert IRQ controller lock to raw spinlock.
  ...

1 files changed, 7 insertions, 33 deletions

diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
index 6184baa56786..561e5da2658b 100644
--- a/arch/mips/alchemy/common/setup.c
+++ b/arch/mips/alchemy/common/setup.c
@@ -29,18 +29,13 @@
 #include <linux/ioport.h>
 #include <linux/jiffies.h>
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/mipsregs.h>
-#include <asm/reboot.h>
 #include <asm/time.h>
 
 #include <au1000.h>
 
 extern void __init board_setup(void);
-extern void au1000_restart(char *);
-extern void au1000_halt(void);
-extern void au1000_power_off(void);
 extern void set_cpuspec(void);
 
 void __init plat_mem_setup(void)
@@ -57,10 +52,6 @@ void __init plat_mem_setup(void)
 	/* this is faster than wasting cycles trying to approximate it */
 	preset_lpj = (est_freq >> 1) / HZ;
 
-	_machine_restart = au1000_restart;
-	_machine_halt = au1000_halt;
-	pm_power_off = au1000_power_off;
-
 	board_setup();  /* board specific setup */
 
 	if (au1xxx_cpu_needs_config_od())
@@ -78,37 +69,20 @@ void __init plat_mem_setup(void)
 	iomem_resource.end = IOMEM_RESOURCE_END;
 }
 
-#if defined(CONFIG_64BIT_PHYS_ADDR)
+#if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_PCI)
 /* This routine should be valid for all Au1x based boards */
 phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
 {
+	u32 start = (u32)Au1500_PCI_MEM_START;
+	u32 end   = (u32)Au1500_PCI_MEM_END;
+
 	/* Don't fixup 36-bit addresses */
 	if ((phys_addr >> 32) != 0)
 		return phys_addr;
 
-#ifdef CONFIG_PCI
-	{
-		u32 start = (u32)Au1500_PCI_MEM_START;
-		u32 end   = (u32)Au1500_PCI_MEM_END;
-
-		/* Check for PCI memory window */
-		if (phys_addr >= start && (phys_addr + size - 1) <= end)
-			return (phys_t)
-			       ((phys_addr - start) + Au1500_PCI_MEM_START);
-	}
-#endif
-
-	/*
-	 * All Au1xx0 SOCs have a PCMCIA controller.
-	 * We setup our 32-bit pseudo addresses to be equal to the
-	 * 36-bit addr >> 4, to make it easier to check the address
-	 * and fix it.
-	 * The PCMCIA socket 0 physical attribute address is 0xF 4000 0000.
-	 * The pseudo address we use is 0xF400 0000. Any address over
-	 * 0xF400 0000 is a PCMCIA pseudo address.
-	 */
-	if ((phys_addr >= 0xF4000000) && (phys_addr < 0xFFFFFFFF))
-		return (phys_t)(phys_addr << 4);
+	/* Check for PCI memory window */
+	if (phys_addr >= start && (phys_addr + size - 1) <= end)
+		return (phys_t)((phys_addr - start) + Au1500_PCI_MEM_START);
 
 	/* default nop */
 	return phys_addr;