Merge tag 'v3.9-rc3' into drm-intel-next-queued

Backmerge so that I can merge Imre Deak's coalesced sg entries fixes,
which depend upon the new for_each_sg_page introduce in

commit a321e91b6d73ed011ffceed384c40d2785cf723b
Author: Imre Deak <imre.deak@intel.com>
Date:   Wed Feb 27 17:02:56 2013 -0800

    lib/scatterlist: add simple page iterator

The merge itself is just two trivial conflicts:

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

1 files changed, 14 insertions, 2 deletions

diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index 47a1bdd88878..72474e18f1e0 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -46,7 +46,11 @@
  * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
  *	(open emitter). Sending this config will enabale open drain mode, the
  *	argument is ignored.
- * @PIN_CONFIG_INPUT_SCHMITT_DISABLE: disable schmitt-trigger mode on the pin.
+ * @PIN_CONFIG_DRIVE_STRENGTH: the pin will output the current passed as
+ * 	argument. The argument is in mA.
+ * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
+ *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
+ *      schmitt-trigger mode is disabled.
  * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
  *	schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
  *	the threshold value is given on a custom format as argument when
@@ -58,10 +62,15 @@
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ * 	this parameter (on a custom format) tells the driver which alternative
+ * 	slew rate to use.
  * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
  *	operation, if several modes of operation are supported these can be
  *	passed in the argument on a custom form, else just use argument 1
  *	to indicate low power mode, argument 0 turns low power mode off.
+ * @PIN_CONFIG_OUTPUT: this will configure the pin in output, use argument
+ *	1 to indicate high level, argument 0 to indicate low level.
  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  *	you need to pass in custom configurations to the pin controller, use
  *	PIN_CONFIG_END+1 as the base offset.
@@ -74,11 +83,14 @@ enum pin_config_param {
 	PIN_CONFIG_DRIVE_PUSH_PULL,
 	PIN_CONFIG_DRIVE_OPEN_DRAIN,
 	PIN_CONFIG_DRIVE_OPEN_SOURCE,
-	PIN_CONFIG_INPUT_SCHMITT_DISABLE,
+	PIN_CONFIG_DRIVE_STRENGTH,
+	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_INPUT_SCHMITT,
 	PIN_CONFIG_INPUT_DEBOUNCE,
 	PIN_CONFIG_POWER_SOURCE,
+	PIN_CONFIG_SLEW_RATE,
 	PIN_CONFIG_LOW_POWER_MODE,
+	PIN_CONFIG_OUTPUT,
 	PIN_CONFIG_END = 0x7FFF,
 };